Structural characterization and optical properties of ZnSe thin films

Zinc selenide (ZnSe) thin films (d = 0.11-0.93 μm) were deposited onto glass substrates by the quasi-closed volume technique under vacuum. Their structural characteristics were studied by X-ray diffraction (XRD) and atomic force microscopy (AFM). The experiments showed that the films are polycrystalline and have a zinc blende (cubic) structure. The film crystallites are preferentially oriented with the (1 1 1) planes parallel to the substrate surface. AFM images showed that the films have a grain like surface morphology. The average roughness, R_a = 3.3-6.4 nm, and the root mean square roughness, R_rms = 5.4-11.9 nm, were calculated and found to depend on the film thickness and post-deposition heat treatment.The spectral dependence of the absorption coefficient was determined from transmission spectra, in the range 300-1400 nm.The values of optical bandgap were calculated from the absorption spectra, E_g = 2.6-2.7 eV.The effect of the deposition conditions and post-deposition heat treatment on the structural and optical characteristics was investigated.     

Structure and properties of nanocomposite Nb-Al-N films

Physics of the Solid State - Nanocomposite Nb-Al-N films prepared by magnetron sputtering have been studied. It has been found that, in the films, there are two stable crystalline structural...     

Structure and properties of nanocrystalline ZnS and ZnSe films

The influence of the condensation temperature on the structure and optical properties of ZnS and ZnSe films is studied. The presence of the hexagonal phase, along with the cubic, is revealed in films deposited on the cleaved NaCl facet. The appearance of the hexagonal phase is explained by the mechanical stress produced at the film-substrate interface.     

Magnetic and structural properties of nanocomposite Co-Ni-Cr-Al-Y-N thin films

The relation between structural and magnetic properties of Co-Ni-Cr-Al-Y-N thin films deposited by reactive r.f. magnetron sputtering was investigated. A marked change in the magnetic behaviour of the films with the different nitrogen partial pressure in the Ar/N₂ deposition atmosphere was observed and qualitatively explained in correlation with the phase composition. The nanocrystalline metal solid-solution obtained at low N₂ content and the nanocrystalline nitride/amorphous composite obtained at high N₂ content are not magnetic, whereas the amorphous phase produced for intermediate N₂ pressures behaves like a ferromagnetic semi-permanent material. The results demonstrate the possibility of modulating the magnetic properties of r.f. magnetron sputtered Co-Ni-Cr-Al-Y-N thin films, thus opening a new route for magnetic multilayer deposition. PACS 68.55.-a; 75.70.Ak; 75.75.+a; 85.70.-w     

Effects of the ZnSe concentration on the structural and optical properties of ZnSe/PVA nanocomposite thin film

This study investigated the effects of ZnSe nanoparticles (NPs) on the structural and (linear and nonlinear) optical properties of polyvinyl alcohol (PVA) thin film. Three samples of ZnSe NP-doped PVA thin films with different concentrations of ZnSe were produced on a glass substrate. The ZnSe NPs were synthesized by pulsed laser ablation of the ZnSe bulk target immersed in distilled water using a 1064 nm wavelength and a high frequency pulsed Nd:YAG laser. The optical bandgap energies of the films were extracted from their UV-Vis-NIR absorption spectra. The corresponding energy bandgaps of the nanocomposite films declined as the ZnSe NPs doping concentration increased. X-ray diffraction analysis was used to characterize the crystalline phases of the ZnSe/PVA nanocomposite films. The concentration-dependent nonlinear optical absorption and nonlinear refraction behaviors of the films after exposure to 532-nm nanosecond laser pulses were investigated using the Z-scan technique. The nonlinear absorption response of the films was positive when measured using an open aperture scheme, which was attributed to the two-photon absorption mechanism. In addition, the nonlinear refraction indices had a negative value and they increased as the concentration of ZnSe NPs in the films increased.     

Physical properties of ZnSe thin films deposited on glass and silicon substrates

ZnSe thin films were deposited onto Corning glass and silicon substrates using thermal evaporation. The samples were prepared at different substrate temperatures. The thin films’ surface chemical composition was determined through Auger electron spectroscopy (AES). AES signals corresponding to Zn and Se were only detected in AES spectra. The samples’ crystallographic structure was studied through X-ray diffraction. The material crystallised in the cubic structure with preferential orientation (111). Optical properties of the ZnSe films were studied over two energy ranges via electron energy loss spectroscopy (10–90 eV) and spectral transmittance measurements (0.4–4 eV). In both cases, the spectral variation of the refractive index and the absorption coefficient were determined by fitting the experimental results with well-established theoretical models. Experimental values for the material’s gap were also found, and photoconductivity (PC) measurements were carried out. Transitions between bands, usually labelled Γ^V₈ → Γ^C₆ and Γ^V₇ → Γ^C₆, were found in the optical and PC responses. A wide spectral photoconductive response between 300 and 850 nm was found in the ZnSe/Si samples prepared at 250 °C substrate temperature.     

Structural and optical properties of ZnSe thin films stacked with PbSe submonolayers

Structural and optical properties of Zinc Selenide (ZnSe) thin films stacked with multiple Lead Selenide (PbSe) submonolayers (ML) were studied. Thermal evaporation was preferred to produce ZnSe–PbSe thin films with the PbSe ML thickness ranges from 2.5 to 10 nm. Polycrystalline nature of the ZnSe was revealed through high resolution X-ray diffractometer measurement. The development of micro strain at the interfaces with increasing PbSe ML thickness was observed. A cross-sectional TEM image shows well-ordered periodicity and reproducibility of the layer thickness. The enhancement of optical absorption of ZnSe was identified upon stacking of PbSe ML. The evidence for quantum confinement in PbSe ML was revealed by the obtained red shift in band gap (2.5–1.8 eV) values as well as photoluminescence emission at 1,071 nm. The presence of tensile strain in the ZnSe layers upon staking of PbSe ML was discussed by the shift in LO phonon modes in Raman spectra.     

Structure and physical-mechanical properties of nanostructured thin films

The structure and mechanical properties of nanostructured thin films based on carbides, nitrides, and borides of transition metals are described. The mechanisms of localized deformation of the films during indentation are compared. It is shown that the tendency of a material to form shear bands during deformation can be predicted using the parameter H³/E², which describes the resistance of the material to plastic deformation. The columnar structure of the films is found to play an important role during deformation, which proceeds via slipping of columnar structural elements along the direction of an applied load.     

Structure and magneto-optical properties of fine-grain garnet thin films

The structure and magneto-optical properties of fine-grain garnet thin films crystallized by the rapid recurrent thermal annealing (RRTA) method have been studied. The RRAT method has been used to crystallize BiGaDyIG garnet single-layer or BiGaDyIG/AI double-layer films and to get nanometer grain size (about 30–50 nm), which results in a large Faraday rotation angle, a smoother surface and fewer voids in the films. Meanwhile we have discovered that the Faraday rotation angle increases with the number of recurrences during the rapid annealing and quenching. With the more recurrent annealing one can not only get a strong Faraday effect, but it suppresses the appearance of DyFeO₃ phase in garnet films, which has been explained very well. By applying the new method, the as-deposited films have been succesfully crystallized to the (BiDy)₃(FeGa)₅O₁₂ garnet phase. They exhibited excellent magneto-optical properties with a coercivity of about 1500 Oe and effective Faraday rotation angle of 1.5°. The composition, magnetic and magneto-optical properties of the crystallized garnet films have been examined.     

Effect of annealing on structural and optical properties of diamond-like nanocomposite thin films

The annealing effect on structural and optical properties of the Diamond-like Nanocomposite (DLN) thin film deposited on glass substrate by Plasma Assisted Chemical Vapor Deposition (PACVD) method has been investigated. The films were annealed at temperature ranging from 300 to 600 °C, with 100 °C interval for 9 minutes by rapid thermal process (RTP) under vacuum. The structural changes of the annealed films have been studied using Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, Scanning Electron Microscope (SEM), and optical parameters have been determined using transmittance and reflectance spectra in UV-UIS-NIR range. The result shows that the refractive index increases gradually from 1.79 to 2.84 with annealing temperature due to out-diffusion of H by breaking Si–H and C–H bond leads to Si–C bond, i.e. more cross linking structure. In higher temperature range, graphitization also enhanced the refractive index. However, the optical band gap at up to 400 °C initially increases from 3.05 to 3.20 eV and then decreases due to graphitization. The film has a great potential to be used as anti-reflection coating (ARC) on silicon-based solar cell.     

Structure and electrical properties of thin films of copper selenide

Electron-diffraction and electron-microscope methods were used to investigate the structure of Cu₂Se films of close to stoichiometric composition. It is shown that in polycrystalline and single-crystal films of thickness >400Å at room temperature, the tetragonal modification is stable, which at temperatures above 400°K is transformed into the cubical modification. In thinner films d<400 Å the cubical modification of copper selenide is stable at room temperature. A sharp peak is observed at 400°K on the temperature dependence of the resistance; this is connected with the phase transition. At room temperature, copper selenide is a degenerate p-type semiconductor with carrier concentration 5 · 10²²–8 · 10²⁰ cm^–3, depending on the thickness of the film.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 8, pp. 90–94, August, 1973.     

Structural, optical properties and VCNR mechanisms in vacuum evaporated iodine doped ZnSe thin films

Iodine doped ZnSe thin films were prepared onto uncoated and aluminium (Al) coated glass substrates using vacuum evaporation technique under a vacuum of 3 × 10⁻⁵ Torr. The composition, structural, optical and electrical properties of the deposited films were analyzed using Rutherford backscattering spectrometry (RBS), X-ray diffraction (XRD), spectroscopic ellipsometry (SE) and study of I-V characteristics, respectively. In the RBS analysis, the composition of the deposited film is calculated as ZnSeI_0.003. The X-ray diffractograms reveals the cubic structure of the film oriented along (1 1 1) direction. The structural parameters such as crystallite size, strain and dislocation density values are calculated as 32.98 nm, 1.193 × 10⁻³ lin⁻² m⁻⁴ and 9.55 × 10¹⁴ lin/m², respectively. Spectroscopic ellipsometric (SE) measurements were also presented for the prepared iodine doped ZnSe thin films. The optical band gap value of the deposited films was calculated as 2.681 eV by using the optical transmittance measurements and the results are discussed. In the electrical studies, the deposited films exhibit the VCNR conduction mechanism. The iodine doped ZnSe films show the non-linear I-V characteristics and switching phenomena.     

Mn掺杂ZnO薄膜的结构及光学性能研究

通过脉冲激光沉积(PLD)法在SiO₂基片上制备了不同含量的Mn掺杂ZnO薄膜.X射线衍射、X射线能谱、原子力显微镜与紫外-可见分光光度计测试结果表明：少量的Mn离子的掺杂并没有改变薄膜的结构，薄膜具有(103)面的择优取向；PLD法制备的ZnO薄膜的成分与靶材基本一致，实现了薄膜的同组分沉积；薄膜表面比较平坦，起伏度小于80nm，颗粒尺寸主要集中在25nm附近；但是Mn离子的掺杂改变了ZnO薄膜的禁带宽度，随Mn掺杂含量的增加，ZnO薄膜的禁带宽度增加；当薄膜中Mn含量从6%增加到 关键词： PLD ZnO薄膜 Mn掺杂 吸收谱     

CoPt(FePt)-C纳米复合膜的结构与磁性

用磁过滤脉冲真空电弧沉积方法制备了CoPt(FePt) C纳米复合薄膜，并在不同温度下进行了退火处理，研究了薄膜中碳的含量以及退火温度对薄膜结构与磁性能的影响.制备态薄膜经过足够高的温度退火后，x射线衍射和磁力显微镜分析发现，在碳基质中生成了面心四方相的CoPt(FePt)纳米颗粒.对于特定组分为Co24Pt31C45和Fe43Pt35C22的薄膜，矫顽力以及颗粒尺寸都随退火温度的升高而增大，当退火温度为700℃时，Co24Pt31C45薄膜的矫顽力为21×105A/m，晶粒尺寸为17nm;当退火温度为650℃时，Fe43Pt35C22相应值分别为28×105A/m和105nm. 关键词： 磁记录材料 磁性薄膜 CoPt FePt纳米复合薄膜     

Effect of deposition parameters on structural, optical and electrical properties of nanocrystalline ZnSe thin films

This paper presents the chemical bath deposition of zinc selenide (n-ZnSe) nanocrystalline thin films on non-conducting glass substrates, in an aqueous alkaline medium using sodium selenosulphate as Se²⁻ ion source. The X-ray diffraction studies show that the deposited ZnSe material is nanocrystalline with a mixture of hexagonal and cubic phase. The direct optical band gap ‘E_g’ for the as-deposited n-ZnSe films is found to be 3.5 eV. TEM studies show that the ZnSe nanocrystals (NCs) are spherical in shape. Formation of ZnSe has been confirmed with the help of infrared (IR) spectroscopy by observing bands corresponding to the multiphonon absorption. We demonstrate the effect of the deposition temperature and reactant concentration on the structural, optical and electrical properties of ZnSe films.     

Physical properties of ZnSe thin films: Air and vacuum annealing evolution to buffer layer applications

In order to develop high efficiency solar cell device by replacing conventional hazardous CdS window layer by environmental friendly Zn-based buffer layer, ZnSe thin films of thickness 100 nm were grown on glass and ITO substrates employing electron beam evaporation technique followed by air and vacuum annealing at temperature 100 °C, 200 °C and 300 °C. As-grown and annealed films were subjected to characterization tools like XRD, UV-Vis spectrophotometer, SEM, EDS and source meter. Structural results reveal the amorphous phase, SEM images indicate uniform deposition without pin holes and EDS patterns confirm the deposition. Transmittance is observed to be high in visible region and band gap is found to change with temperature of the treatment and I-V measurements demonstrate ohmic nature. On the basis of optimized results, the films annealed at 200 °C in vacuum may be used as buffer layer to develop high efficiency Cd-based and CIGS thin film solar cells.     

Photoelectrochemical properties of electrodeposited CdSe and CdSe/ZnSe thin films in sulphide-polysulphide and ferro-ferricyanide redox systems

Polycrystalline, (111) textured single CdSe and binary CdSe/ZnSe thin films were prepared by electrodeposition and used as active electrodes in regenerative, liquid junction solar cells with aqueous sulphide-polysulphide or ferro-ferricyanide redox electrolytes. The influence of ZnSe on the photoelectrochemical properties of CdSe was investigated. Microchemical characterization of the cell ingredients was made by X-ray diffraction, scanning microscopy imaging and atomic absorption spectrophotometry. The semiconductor electrodes could behave as rectifying diodes within certain conditions, though cell operation was inevitably associated to chemical changes of the electrodes. Aspects of the corrosion effects are discussed and the stabilization of particular cells is demonstrated.     

Structure and magnetoresistive properties of three-layer thin films of spin-valve type

Three-layer thin films of spin-valve type Co/Сu/Ni_xFe_100-x at x = 20–80 at.% were prepared by electron-beam sputter deposition. The investigated phase state and magnetoresistive properties were done for as-deposited and annealed to 400, 550, and 700 K films. The measurements of field dependences of magnetoresistance were held at different temperatures. It was demonstrated that phase state, crystal structure, and magnetoresistive properties of Co/Сu/Ni_xFe_100-x systems strongly dependent on both Ni_xFe_100-x composition Ni_xFe_100-x and heat treatment conditions.