Alteration in the surface properties of direct-current discharge-treated tetrafluoroethylene-ethylene copolymer films

A change in the contact properties of the surface of a tetrafluoroethylene-ethylene copolymer film by treatment of its samples mounted on the cathode and anode in a dc discharge has been studied. It has been shown that the modification leads to a significant improvement in the contact properties of the films owing to the appearance of oxygen-containing polar groups on the polymer surface. The formation of such groups has been proved by X-ray photoelectron spectroscopy. The peel strength of both the untreated and modified films was measured by the T-peel test method.     

木粉/聚乙烯复合材料的等离子体表面处理——等离子体处理时间对复合材料表面特性的影响

为改善木粉/聚乙烯复合材料的表面粘接性,实现木粉/聚乙烯复合材料的无缝连接,利用低温等离子体处理技术,对木粉/聚乙烯复合材料进行了表面处理.采用接触角测试、傅立叶变换红外光谱分析(FTIR)以及X射线光电子能谱分析(XPS)研究了等离子体处理前后复合材料表面性能的变化.试验结果表明,经等离子体处理后,复合材料表面的接触角减小,表面润湿性得以改善;FTIR分析结果表明,经等离子体处理后,复合材料表面有—OH、—C=O和—O—C=O基团生成;XPS分析表明,经等离子体处理后,复合材料表面含氧基团的含量增加,在较短的时间内表面氧元素含量增加会达到平衡,且生成大量的—O—C=O基团。     

Contact angle hysteresis, adhesion, and marine biofouling

Adhesive and marine biofouling release properties of coatings containing surface-oriented perfluoroalkyl groups were investigated. These coatings were prepared by cross-linking a copolymer of 1H,1H,2H,2H-heptadecafluorodecyl acrylate and acrylic acid with a copolymer of poly(2-isopropenyl-2-oxazoline) and methyl methacrylate at different molar ratios. The relationships between contact angle, contact angle hysteresis, adhesion, and marine biofouling were studied. Adhesion was determined by peel tests using pressure-sensitive adhesives. The chemical nature of the surfaces was studied by using X-ray photoelectron spectroscopy. Resistance to marine biofouling of an optimized coating was studied by immersion in seawater and compared to previous, less optimized coatings. The adhesive release properties of the coatings did not correlate well with the surface energies of the coatings estimated from the static and advancing contact angles nor with the amount of fluorine present on the surface. The adhesive properties of the surfaces, however, show a correlation with water receding contact angles and contact angle hysteresis (or wetting hysteresis) resulting from surface penetration and surface reconstruction. Coatings having the best release properties had both the highest cross-link density and the lowest contact angle hysteresis. An optimized coating exhibited unprecedented resistance to marine biofouling. Water contact angle hysteresis appears to correlate with marine biofouling resistance.     

Change in the surface properties of poly(vinylidene fluoride) films by treatment in direct-current discharge

It has been found that treatment in dc discharge results in a substantial and time-invariant increase in the surface energy of poly(vinylidene fluoride) films. This effect is obviously due to the formation of oxygen-containing groups on the polymer surface, a fact that is corroborated by Fourier-transform IR spectroscopy and X-ray photoelectron spectroscopy data. It has been shown that dc discharge is more effective in altering the contact properties of the polymer surface than low-frequency glow discharge.     

Preparation and properties of thin films of hyperbranched polyesters with different end groups

Hyperbranched polyesters (HBP) with different end groups were prepared as thin films. They were characterized with regard to their chemical composition, thickness, optical constants and morphology using infrared spectroscopy, spectroscopic ellipsometry, and atomic force microscopy. The surface properties of the films were determined by zeta‐potential and contact angles measurements. The differences in the molecular structure and surface energetic and acid‐base properties between HBP materials with carboxylic, hydroxy and acetoxy end groups result in differences in their swelling behavior in atmospheric humidity. The swelling behavior at different atmospheric humidity was observed in situ using spectroscopic ellipsometry and reflectometric interference spectroscopy. From the results it can be concluded that HBP films can be used potentially as sensoric materials.     

SURFACE REARRANGEMENTS OF OXYGEN PLASMA TREATED POLYSTYRENE： SURFACE DYNAMICS AND HUMIDITY EFFECT

The time evolution of oxygen plasma treated polystyrene(PS)surfaces was investigated upon storing them in theair under controlled humidity conditions.The methods of water contact angle,X-ray photoelectron spectroscopy(XPS),sumfrequency generation(SFG)vibrational spectroscopy,and atomic force microscopy(AFM)were used to infer the surfaceproperties and structure.Chemical groups containing oxygen were formed on the PS surface with the plasma treatment,demonstrated by water contact angle and XPS.The surface polarity decayed markedly on time,as assessed by steady increasein the water contact angle as a function of storage time,from zero to around 60°.The observed decay is interpreted as arisingfrom surface rearrangement processes to burying polar groups away from the uppermost layer of the surfaces,which is incontact with air.On the other hand,XPS results show that the chemical composition in the first 3 nm surface layer isunaffected by the surface aging,and the depth profile of oxygen is essentially the same with time.A possible change of PSsurface roughness was examined by AFM,and it showed that the increase of water contact angle during surface aging couldnot be attributed to surface roughness.Thus,it is concluded that surface aging is attributable to surface reorganization andthe motion of oxygen containing groups is confined within the XPS probing depth.SFG spectroscopy,which is intrinsicallyinterface-specific,was used to detect the chemical structure of PS surface at the molecular level after various aging times.The results are interpreted as follows.During the aging of the plasma treated PS surfaces,the oxygen containing groupsundergo reorientation processes toward the polymer bulk and/or parallel to the surface,while the CH_2 moiety stands up onthe PS surface.Our results indicate that the surface configuration changes do not require large length scale segmentalmotions or migration of macromolecules.Motions that are responsible for surface configuration changes could be relativelysmall rotational motions.The aging behaviors under different relative humidity conditions were shown to be similar from18% to 91%,whereas the kinetics of surface polarity decays were faster in higher relative humidity.Here,the surfacerearrangement of polystyrene films that were previously treated by oxygen plasma and aged,and was investigated in terms ofcontact angle after the water immersion.The contact angles of the water-immersed samples were found to change andapproach the initial values before the immersion asymptotically.     

Surface characterization of poly(L-lactic acid)-methoxy poly(ethylene glycol) diblock copolymers by static and dynamic contact angle measurements, FTIR, and ATR-FTIR

The surface composition and surface free energy properties of two types of amphiphilic and semicrystalline diblock copolymers consisting of poly(L-lactic acid) coupled to (methoxy poly(ethylene glycol) (PLLA-MePEG) having differing block lengths of PEG were investigated by using static and dynamic contact angle measurements, transmission Fourier infrared spectroscopy (FTIR), and attenuated total reflection spectroscopy (ATR-FTIR) and compared with results obtained from PLLA and MePEG homopolymers. The contact angle results were evaluated by using the van Oss-Good method (acid-base method), and it was determined that the Lewis base surface tension coefficient (gamma-) of the copolymers increased with an increase of the PEG molar content at the copolymer surface. This result is in good agreement with the transmission FTIR and ATR-FTIR results but not proportional to them, indicating that the surfaces of the copolymers are highly mobile and that the molecular rearrangement takes place upon contact with a polar liquid drop. The dynamic contact angle measurements showed that the strong acid-base interaction between the oxygen atoms in the copolymer backbone of the relatively more hydrophilic PEG segments with the Lewis acidic groups of the polar and hydrogen-bonding water molecules enabled the surface molecules to restructure (conformational change) at the contact area, so that the PEG segments moved upward, whereas the apolar methyl pendant groups of PLLA segments buried downward.     

Surface modification of microporous polypropylene membranes by the grafting of poly(γ-stearyl-l-glutamate)

A polypeptide, poly(γ-stearyl-l-glutamate) (PSLG), was grafted on the surface of hydrophobic polypropylene hollow fiber membranes through the ring opening polymerization of N-carboxyanhydride (NCA) of γ-stearyl-l-glutamate initiated by amino groups which was generated by ammonia plasma. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), together with water contact angle and bovium serum albumin adsorption measurements were used to characterize the modified membrane surface. The XPS and FT-IR spectra demonstrated that polypeptide was actually grafted on the membrane surface despite of the low degree of graft polymerization due to the hydroxyl groups on the membrane surface. To subject the ammonia plasma-treated membrane with γ-(aminopropyl)triethanoxysilane (γ-APS) which can react with hydroxyl groups and leave amino groups, the degree of graft polymerization could be improved. The bovium serum albumin adsorption measurement was conducted to further examine the surface properties of modified and original membranes. Potential applications of the PSLG grafted membranes are expected for enantiomer separation and/or enzyme immobilization.     

Alteration in the surface properties of direct-current discharge-treated tetrafluoroethylene-vinylidene fluoride copolymer films

A change in the contact properties of the surface of tetrafluoroethylene-vinylidene fluoride copolymer films by a dc discharge treatment has been studied, depending on the treatment time and the discharge current. It has been shown that the treatment of the films at the anode and cathode leads to a significant decrease in the contact angle and an increase in the total surface energy and its polar term. The change in the contact properties of the plasma-modified films during storage and heating has been studied as well. The experiments have shown that the formation of polyconjugated structures and crosslinking of macromolecules take place in the film surface layer during long-term treatment at the anode (>60 s, 50 mA), processes that result in an acetone-insoluble layer. The composition and surface structure of the films have been examined by Fourier-transform IR spectroscopy and X-ray photoelectron spectroscopy. The formation of new oxygen-containing groups and double bonds on the polymer surface and crosslinking of macromolecules in the case of anode treatment have been revealed. It has been found experimentally that the discharge treatment increases the peel strength in the Scotch® 810/copolymer film system.     

Surface modification of high heat resistant UV cured polyurethane dispersions

To modify the surface of UV cured polyurethane dispersion (UV-PUD), fluorinated PU called surface modifying agent (SMA) was blended with base PU prior to dispersion in water. X-ray photoelectron spectroscopy (XPS) and contact angle measurements showed that surfaces of dispersion cast film are significantly enriched with fluorine groups. Atomic force microscopy (AFM) showed that surface was roughened with the addition of SMA, which provided possible mechanism of increased water resistance as well as low friction coefficient of the film. On the other hand, hardness, mechanical and dynamic mechanical properties indicated that the bulk properties are marginally altered by the additive amount of SMA.     

Surface modification of PDMS by surface-initiated atom transfer radical polymerization of water-soluble dendronized PEG methacrylate

The current paper reports the synthesis of a highly hydrophilic, antifouling dendronized poly(3,4,5-tris(2-(2-(2-hydroxylethoxy)ethoxy)ethoxy)benzyl methacrylate) (PolyPEG) brush using surface initiated atom transfer radical polymerization (SI-ATRP) on PDMS substrates. The PDMS substrates were first oxidized in H₂SO₄/H₂O₂ solution to transform the Si-CH₃ groups on their surfaces into Si-OH groups. Subsequently, a surface initiator for ATRP was immobilized onto the PDMS surface, and PolyPEG was finally grafted onto the PDMS surface via copper-mediated ATRP. Various characterization techniques, including contact angle measurements, attenuated total reflection infrared spectroscopy, and X-ray photoelectron spectroscopy, were used to ascertain the successful grafting of the PolyPEG brush onto the PDMS surface. Furthermore, the wettability and stability of the PDMS-PolyPEG surface were examined by contact angle measurements. Anti-adhesion properties were investigated via protein adsorption, as well as bacterial and cell adhesion studies. The results suggest that the PDMS-PolyPEG surface exhibited durable wettability and stability, as well as significantly anti-adhesion properties, compared with native PDMS surfaces. Additionally, our results present possible uses for the PDMS-PolyPEG surface as adhesion barriers and anti-fouling or functional surfaces in biomedical applications.     

Contributions to the Characterization of Chlorinated Polyisoprene Surfaces

Summary: The present work is focused on the characterization of the surface properties and the mechanical properties of chlorinated polyisoprene films. Cross-linked polyisoprene films were treated with acidified hypochlorite solution and the influence of the chlorination time on the surface properties was determined by spectroscopic techniques including FT-IR spectroscopy and X-ray photoelectron spectroscopy (XPS). The surface morphology was investigated by scanning electron microscopy (SEM), optical microscopy and contact angle measurements. In addition, the effect of the chlorination time on the tensile strength and ageing stability of natural rubber latex gloves was investigated.     

Photolabile carboxylic acid protected terpolymers for surface patterning. Part 2: Photocleavage and film patterning

The surface properties of films made of p-methoxyphenacyl derivative terpolymers, associated with photocleavage by UV irradiation, and their optical patterning are investigated. The deprotection reaction has been monitored by UV and FTIR spectroscopy, contact angle measurements, and X-ray photoelectron spectroscopy, revealing the photoremoval of the protecting p-methoxyphenacyl group in high yields under mild conditions. Parallel and serial patterning of the films has been performed by selective irradiation through optical masks and by laser irradiation via fiber tips of a scanning near-field optical microscope, respectively. By irradiation of photolabile protected functional groups, free carboxylic groups become exposed to the surface with which fluorescent dyes and proteins can be associated specifically.     

Direct-current discharge treatment of polytetrafluoroethylene films

The effect of treatment in a low-pressure dc discharge on the surface properties of polytetrafluoroethylene (PTFE) films modified at the anode and cathode was examined. It was found that the anode treatment of the films considerably improves the adhesive properties of the polymer and makes it possible to obtain substantially lower values of the contact angle and higher values of the work of adhesion and surface energy than in the case of other PTFE surface modification techniques. By means of IR and X-ray photoelectron spectroscopy, it was shown that discharge treatment at the anode and cathode noticeably increases the amount of oxygen-containing groups on the surface of the films.     

Surface modification of glass beads with poly(acrylic acid)

Non‐porous P₂ glass beads were etched with sodium hydroxide to increase the number of silanol groups that could be used to modify the surface. The etched glass beads were then functionalized with 3‐aminopropyltriethoxysilane (APS) and/or glycidoxypropyltrimethoxysilane (GPS). The surface of the glass beads were further modified with poly(acrylic acid) (PAA) by reacting the carboxyl groups on PAA with the amino groups of the pregrafted APS. The chemical modifications were characterized by FT‐IR spectroscopy, particle size analyzer and tensiometry for contact angle and porosity measurements. Five different molecular weight PAA polymers ranging from 2000 to 3,000,000 were grafted with less than expected increase of grafted PAA with molecular weight. The amount of APS and PAA on the surface was determined from thermogravimetric analysis and elemental analysis data. The surface properties of the surface modified glass beads were determined by measuring water and hexane penetration rate and contact angle. The surface morphology was examined by scanning electron microscopy. Copyright © 2006 John Wiley & Sons, Ltd.     

Laser induced surface modification of polydimethylsiloxane as a super-hydrophobic material

In order to render the surface of polydimethylsiloxane (PDMS) super-hydrophobic without changing its bulk properties, a PDMS film without photosensitizer was exposed to CO₂ pulsed laser, at room temperature, as the excitation source. The modified surfaces have been studied by performing scanning electron microscopy (SEM) combined with energy dispersive X-ray analysis (EDXA) and attenuated total reflectance infrared (ATR-IR) spectroscopy. To evaluate the surface property, the water drop contact angle was measured. The dependence of ---Si---O---Si infrared peak intensity, O/Si ratio and water drop contact angle of the treated PDMS as a function of the number of laser pulses were studied. SEM micrographs and water drop contact angle variations show the uniform porosity and super-hydrophobic nature on the surface of PDMS. ATR-FTIR spectra show that the modified PDMS surface contains carbonate groups which enriched the oxygen content of the surface. EDXA analysis shows a higher percentage of oxygen on the surface of the modified PDMS. The hydrophobicity of the samples was found to depend upon the number of laser pulses, but with significant variation between the treated samples. The bulk mechanical properties of PDMS after being laser-treated did not change as shown by dynamic mechanical thermal analysis (DMTA).     

Surface characterization and radical decay studies of oxygen plasma‐treated PMMA films

Polymethylmethacrylate (PMMA) films were modified by RF oxygen plasma with various powers applied for different periods, and the effects of these parameters on the surface properties such as hydrophilicity, surface free energy (SFE), chemistry, and topography were investigated by water contact angle, goniometer, X‐ray photoelectron spectroscopy (XPS), and atomic force microscopy, and the types of the created free radicals and their decay were detected by electron spin resonance spectroscopy (ESR). SFE and contact angle results varied depending on the plasma parameters. Oxygen plasma treatment (100 W–30 min) enhanced the hydrophilicity of PMMA surface as shown by decreasing the water contact angle from 70° to 26°. XPS analysis showed the change in the amounts of the present functionalities as well as formation of new groups as free carbonyl and carbonate groups. The roughness of the surface increased considerably from ~2 nm to ~75 nm after 100 W–30 min oxygen plasma treatment. ESR analysis indicated the introduction of peroxy radicals by oxygen plasma treatment, and the intensity of the radicals increased with increasing the applied power. Significant decrease in radical concentration was observed especially for the samples treated with higher powers when the samples were kept under the atmospheric conditions. As a conclusion, RF plasma, causes changes in the chemical and physical properties of the materials depending on the applied parameters, and can be used for the creation of specific groups or radicals to link or immobilize active molecules onto the surface of a material. Copyright © 2012 John Wiley & Sons, Ltd.     

Hemocompatibility and ultrafiltration performance of PAN membranes surface‐modified by hyperbranched polyesters

Maleic anhydride was grafted onto a polyacrylonitrile (PAN) membrane surface via ultraviolet irradiation. Then, hyperbranched polyester, with varying numbers of hydroxyl end‐groups (H20, H30, and H40), was grafted onto the PAN membrane surface by the reaction of hydroxyl groups with anhydride groups of maleic anhydride. The modified membranes were characterized by scanning electron microscopy, static water contact angle, and attenuated total reflectance‐Fourier transform infrared spectroscopy measurements. The modified membranes showed a higher water flux and better antifouling properties than pristine PAN membranes, and their hydrophilicity was significantly improved. Membrane biocompatibility was characterized by platelet adhesion, and the results indicate that the modified membranes exhibited good biocompatibility. Copyright © 2016 John Wiley & Sons, Ltd.     

表面接枝含氟苯乙烯共聚物的聚酯薄膜制备与表征

利用表面引发原子转移自由基聚合(SI-ATRP)在聚对苯二甲酸乙二醇酯(PET)薄膜表面接枝苯乙烯和4-氟苯乙烯的共聚物.研究不同反应时间和不同配比下接枝共聚物对聚酯薄膜表面组成、结构和性能的影响.通过傅利叶变换红外光谱仪(ATR/FTIR),X-射线光电子能谱仪(XPS),凝胶渗透色谱(GPC)和扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析;利用接触角测试和表面能计算对比研究接枝改性前后PET薄膜的表面性能.结果表明反应时间和单体百分含量对接枝百分率及接触角有一定的影响,随着反应时间的增长,聚酯薄膜表面接枝百分率增大,接触角增加,表面自由能下降.     

Synthesis and properties of novel fluorinated polyurethane based on fluorinated gemini diol

In the current study, the novel fluorinated polyurethanes (FPUs) that contained the gemini branched fluoroether side groups on the hard segments were developed. In brief, to obtain these FPUs, a new class of fluorinated gemini diol with double‐branched fluoroether side groups was first synthesized and characterized by using Fourier transform infrared spectroscopy, nuclear magnetic resonance, and mass spectrometry. Subsequently, a series of FPUs were designed and prepared by using hexamethylene diisocyanate, poly (tetramethylene oxide glycol), 1,4‐butanediol, and fluorinated gemini diol. Analysis of the FPUs' surface properties from contact angle analysis indicated that the water contact angle increased from 81° to more than 120° when the content of fluorinated gemini diol was increased. Differential scanning calorimetry results revealed that introduction of fluorinated gemini dio decreased the T_g of FPUs, causing a better phase separation. Results from thermogravimetric analysis studies indicated the thermal stability of FPUs was improved. Scanning electron microscopy and energy dispersive X‐ray spectroscopy revealed that fluoroether groups migrate to and enrich on the outmost surface of FPUs.