Impact of impregnation pressure on desulfurization performance of Zn-based sorbents supported on semi-coke

High-pressure impregnation, a new preparation method for sorbents to remove H2S from hot coal gas, is introduced in this paper. Semi-coke (SC) and ZnO is selected as the support and active component of sorbent, respectively. The sorbent preparation process includes high-pressure impregnation, filtration, ovendry and calcination. The aim of this research is to primarily study the effects of the impregnation pressure on physical properties and desulfurization ability of the sorbent. The desulfurization experiment was carried out in a fixed-bed reactor at 500°C and a simulated coal gas used in this work was composed of CO (33 vol%), H2 (39 vol%), H2S (300 ppm in volume), and N2 (balance). Experimental results show that the pore structure of the SC support can be improved effectively and ZnO active component can be uniformly dispersed on the support, with the small particle size of 10-500 nm. Sorbents prepared using high-pressure impregnation have better desulfurization capacity and their active components have higher utilization rate. P20-ZnSC sorbent, obtained by high-pressure impregnation at 20 atm, has the best desulfurization ability with a sulfur capacity of 7.54 g S/100g sorbent and a breakthrough time of 44 h. Its desulfurization precision and efficiency of removing H2S from the middle temperature gases can reach <1 ppm and >99.7%, respectively, before sorbent breakthrough.     

Desulfurization kinetics of ZnO sorbent loaded on semi-coke support for hot coal gas

Zn-based sorbent (Z20SC) prepared through semi-coke support in 20 wt% zinc nitrate solution by high-pressure impregnation presents an excellent desulfurization capacity in hot coal gas,in which H2 S can not be nearly detected in the outlet gas before 20 h breakthrough time.The effects of the main operational conditions and the particle size of Z20SC sorbent on its desulfurization performances sorbent were investigated in a fixed-bed reactor and the desulfurization kinetics of Z20SC sorbent removing H2 S from hot coal gas was calculated based on experimental data.Results showed that the conversion of Z20SC sorbent desulfurization reaction increased with the decrease of the particle size of the sorbent and the increases of gas volumetric flow rate,reaction temperature and H 2 S content in inlet gas.Z20SC sorbent obtained from hydrothermal synthesis by high-pressure impregnation possessed much larger surface area and pore volume than semi-coke support,and they were significantly reduced after the desulfurization reaction.The equivalent grain model was reasonably used to analyze experimental data,in which k s=4.382×10-3 exp(-8.270×103/RgT) and Dep=1.262×10-4exp(1.522×104/RgT).It suggests that the desulfurization reaction of the Z20SC sorbent is mainly controlled by the chemical reaction in the initial stage and later by the diffusion through the reacted sorbent layer.     

炭基载体对超声加压浸渍法制备锌基脱硫剂中温硫化性能的影响

以活性炭(AC)、褐煤半焦(LSC)、烟煤半焦(BSC)和褐煤焦(LC)4种炭基材料作为载体,利用超声辅助加压浸渍法分别制备了氧化锌炭基系列中温煤气脱硫剂。借助固定床硫化反应测试装置、氮气吸附、XRD和SEM等手段对4种脱硫剂的脱硫性能、物相组成、比表面积和孔结构进行了测试和表征。结果表明,超声辅助加压浸渍法能够有效改善炭基材料的孔隙结构,加压水热处理后的褐煤半焦比表面积可增大为原来的11倍;炭基材料种类不会影响氧化锌炭基脱硫剂中活性组分的赋存形态,但直接影响活性组分的上载率及其在载体表面分散的均匀性,进而影响脱硫剂的中温硫化性能。褐煤半焦制备的脱硫剂Zn/LSC中较高的活性组分利用率和丰富的孔隙结构使其脱硫效果最佳,脱硫精度达到99.99%时的穿透时间和实际硫容分别达到11.0 h和5.17%。褐煤半焦孔结构最易于改性,是加压水热合成中温煤气脱硫剂的一种优良的载体材料,这也是资源相对丰富的褐煤有效利用的途径之一。     

SO2气氛下半焦负载Zn/Fe/Ce高温煤气脱硫剂的再生行为研究

以共沉淀法制备了半焦负载Zn/Fe/Ce（物质的量比1.0：2.0：0.6）高温煤气脱硫剂,在固定床装置上研究了再生反应温度、进口SO₂浓度以及再生气空速对再生性能的影响,并进行三次硫化-再生循环测试。采用XRD、SEM、BET等测试手段对脱硫剂的新鲜样、硫化样及再生样进行了表征。实验结果表明,半焦负载Zn/Fe/Ce高温煤气脱硫剂在SO₂气氛下600 ℃就能发生再生反应,且再生后的主要产物为ZnFe₂O₄、CeO₂和单质硫;最佳再生条件为,再生温度700 ℃、进口SO₂体积分数为12%、再生气空速为5 000 h^-1。脱硫剂经过多次硫化-再生循环后,脱硫剂仍能保持较好的硫化活性。     

半焦吸附剂烟气脱硫脱硝性能

采用廉价半焦为原料,经硝酸氧化和高温热处理改性后,负载金属氧化物制备半焦吸附剂,考察吸附剂的脱硫脱硝性能和再生性能,并利用BET、TEM和TPD等手段研究影响半焦吸附剂性能的内在因素.结果表明,当烟气组成为NO-O2-N2时,吸附剂具有良好的脱硝性能,失活吸附剂经水洗再生后,脱硝活性恢复较好;当烟气组成为SO2-O2-...     

Effect of binder on the properties of iron oxide sorbent for hot gas desulfurization

The most difficult problem in hot gas desulfurization in Integrated Coal Gasification Combined Cycle (IGCC) is the pulverization of sulfur removal sorbents. Appropriate binders for hot gas sulfur removal sorbents can solve the pulverization problem. In this paper, six sorbents with binders of different argillaceous minerals were prepared by mechanical mixing method. Desulfurization behavior for hot gas desulfurization sorbents was investigated in a fixed-bed reactor. Result showed that sorbent NTKW2 with binder of clay had a better sulfidation performance. NTKW2 had a more stable performance than other sorbents in the continuous sulfidation-regeneration cycles. Sulfur capacity of sorbent remained the same in each cycle. The desulfurization efficiency and mechanical strength of NTKW2 were the best among the tested sorbents. The behavior of NTKW2 at different temperatures showed different performances, and the best reaction temperature was 550 ℃. Higher heat stability, sulfur capacity and desulfurization efficiency were found on NTKW2 in six continuous sulfidation-regeneration cycles.     

溶胶-凝胶法制备TiO2负载活化半焦光催化烟气脱硝

利用超声辅助溶胶-凝胶法,以钛酸正丁酯为钛源,制备了TiO2负载于活化半焦的光催化剂。考察了TiO2负载量,煅烧温度和时间,以及水对光催化脱硝活性的影响。利用X射线衍射（XRD）,BET,FT-IR,扫描电镜（SEM）以及能谱分析（EDS）等方法对催化剂进行了表征分析。实验结果表明,TiO2负载量为5.22 %,煅烧温度500 癈,煅烧时间为1 h时,TiO2/SC光催化脱硝剂效果最好,反应3小时后脱硝率仍高于70 %。通过添加自由基捕获剂的方法确定TiO2/ASC光催化脱硝过程中起主要作用的活性物种为?OH和?O2-,而空穴在本实验的光催化过程中几乎不起作用。对催化剂的再生研究发现,高温（400癈）水热一次再生可恢复催化剂脱硝活性至新鲜催化剂的100%,三次再生效果仍为新鲜催化剂脱硝率的80%。     

Hydrotreating performance of La-modified Ni/Al2O3 catalysts prepared by hydrothermal impregnation method

Kinetics and Catalysis - To enhance the surface active sites of the catalyst, a series of La-modified Ni/γ-Al2O3 samples were prepared by hydrothermal impregnation method and characterized by...     

铝基氧化铜干法烟气脱硫及再生研究

采用浸渍法制备了XP型和DS型两种铝基氧化铜脱硫剂，并利用制得的脱硫剂进行了烟气循环脱硫-再生实验，同时利用BET、XRD和EPMA等方法研究了载体性质对脱硫剂性能的影响以及脱硫剂的表面微观结构在脱硫和再生过程的变化。实验和分析表明，用于制备脱硫剂的载体应同时具备较大的比表面积和合适的孔结构，实验条件下制得的铝基氧化铜脱硫剂的脱硫效率可达90％，该脱硫剂在多次循环脱硫-再生过程中性能保持稳定。     

过渡金属对燃烧法制MgO负载 Cu2O催化剂的改性研究

本文以柠檬酸燃烧法制备MgO(B)载体,采用浸渍还原法以水合肼为还原剂制备Cu2O/MgO(B)催化剂,以环己醇脱氢制环己酮为探针反应,考察了过渡金属Fe、Co、Ni、Mo、Mn的添加对Cu2O/MgO(B)催化性能的影响;采用X射线衍射(XRD)、程序升温还原(TPR)、二氧化碳程序升温脱附(CO2-TPD)以及环己醇、环己酮程序升温脱附(环己醇/环己酮-TPD) 等手段对催化剂进行了表征.研究结果表明,Mn-Cu2O/MgO(B) 、 Ni-Cu2O/MgO(B)的催化性能优于Cu2O/MgO(B).其原因主要是Mn、Ni的添加使Cu2O的抗还原能力增强,Cu2O更稳定;同时,Mn和Ni的添加使Cu2O/MgO(B)催化剂对反应物和产物的吸附强度减弱;这些都有利于脱氢反应的进行.所有催化剂都呈碱性,是其具有高环己酮选择性的原因之一.     

Chromatographic effect during the preparation of supported two-component catalysts by impregnation

The reason for variation in the granule depth of the component ratio in supported two-component catalysts during their preparation has been studied. This phenomenon, which may be called chromatographic effect, depends on the different affinities between substrate and ions in the impregnating solution. The model system chosen is CuCo₂O₄/Al₂O₃. It has been established that after modification of the support with Cu²⁺ ions, the stoichiometric CuCo₂O₄ phase is formed. The catalysts obtained have an enhanced activity.     

The removal of H2S derived from livestock farm on activated carbon modified by combinatory method of high-pressure hydrothermal method and impregnation method

H₂S is considered as the main gas pollutant from livestock farm and activated carbon (AC) is widely used as adsorbent for H₂S. This paper focuses on the influence of modification conditions and operation conditions on the H₂S adsorption performance on AC samples. The H₂S adsorption performance on modified AC (MAC) samples by single and combinatory method has been investigated. It is concluded that the MAC by combinatory method of high-pressure hydrothermal method followed by alkaline solution impregnation method could promote the H₂S adsorption performance remarkably. The H₂S adsorption performance differs with different operation conditions. Meanwhile the samples of fresh AC and exhausted AC have been characterized using BET, FTIR, TPD and Boehm titration method. The experimental results are confirmed that the characteristics of AC have significant influence on the adsorption ability for H₂S.     

添加剂对乙二胺湿法烟气脱硫的影响

采用自主设计的鼓泡吸收装置,以乙二胺溶液为脱硫剂,研究了盐酸、硫酸、磷酸、柠檬酸和硼酸作为添加剂对湿法烟气脱硫的影响。实验结果表明,加入酸添加剂后,提高了吸收液的有效吸收容量。其中,乙二胺/硼酸和乙二胺/磷酸的有效吸收容量较高,分别为266 mg/L和269 mg/L,pH值缓冲效果最佳。同时发现,乙二胺溶液的脱硫率随时间的延长而迅速减小;加入添加剂后,吸收液能在较长时间内保持较高脱硫率。10次吸收-解吸循环实验结果显示,乙二胺/硼酸、乙二胺/磷酸和乙二胺/柠檬酸的平均脱硫率均达99%,SO2解吸顺序为乙二胺/硼酸乙二胺/磷酸乙二胺/柠檬酸。硼酸和磷酸可强化乙二胺湿法烟气脱硫过程,是具有开发前景的添加剂。     

Co掺杂铁基氧化物吸附剂燃煤烟气脱汞实验研究

使用柠檬酸法制备了Co掺杂的铁基氧化物(FeCo)吸附剂,通过固定床脱汞实验装置系统考察了FeCo吸附剂的脱汞性能,并利用比表面积(BET)、X射线衍射(XRD)、H₂-程序升温还原(H₂-TPR)、傅里叶红外光谱(FT-IR)、X射线光电子能谱(XPS)等表征手段分析吸附剂的物理化学特性。结果表明,α-Fe₂O₃中掺入Co后,比表面积、孔结构特性均得到改善,且氧化还原性能也相应提升;FeCo吸附剂在200-250℃获得最高约97%的脱汞效率;烟气中O₂和NO的存在有助于FeCo吸附剂对Hg⁰的脱除,而SO₂和H₂O则抑制FeCo吸附剂对Hg⁰的脱除,同时NO能削弱SO₂对FeCo脱汞的抑制作用。在脱汞过程中,FeCo吸附剂表面的活性组分Fe³⁺、Co³⁺和O^*均消耗,参与了Hg⁰氧...     

黏结剂对铁酸锌脱硫剂在高温煤气中脱硫性能的影响

以硝酸铁、硝酸锌、氨水及黏结剂为主要原料,用共沉淀法制成六种铁酸锌脱硫剂。研究了各种黏结剂的加入对脱硫剂的尖晶石结构、硫容量和脱硫效果的影响,在固定床上对其进行脱硫试验。并用X射线衍射（XRD）、扫描电子显微镜(SEM)和气体吸附等测试手段,对脱硫剂的物相组成、结构、比表面积和孔容进行了表征。结果表明,用共沉淀法制备的铁酸锌,具有不受黏结剂影响的尖晶石结构,其颗粒属于微米级;添加高岭土黏结剂的脱硫剂的脱硫效果最好,添加硅藻土的脱硫剂的脱硫效果最差;不同黏结剂对脱硫剂的织构的影响不同;脱硫剂的反应活性和硫容量与其孔容的大小有关。     

A voltammetric sensor on the basis of bismuth nanoparticles prepared by the method of gas condensation

A procedure is developed for the immobilization of bismuth nanoparticles prepared by the method of gas condensation on inert supports manufactured by the screen printing method using carbon-containing inks. The electrochemical behavior of the immobilized bismuth nanoparticles is investigated, and the conditions of their electrochemical activation are found. The composition of the modifying suspension “bismuth nanoparticles-liquid” is optimized. The elaborated thick-film carbon-containing electrode modified by bismuth nanoparticles is shown to be similar in its analytical parameters to the commercially available thick-film carbon-containing electrode premodified by calomel, and substantially exceeds carbon-containing electrodes with electrolytically deposited bismuth films in its properties. The limits of detection for heavy metals by stripping voltammetry are as follows (μg/L): 0.38 for Zn(II), 0.40 for Cd(II), and 0.55 for Pb(II) at the preconcentration time 180 s.     

Synthesis, characterization and gas permeation properties of a silica membrane prepared by high-pressure chemical vapor deposition

Cylindrical silica membranes with dead-end structure were prepared by an extended counter-diffusion chemical vapor deposition (CVD) method, in which a tetramethylorthosilicate (TMOS) silica source was fed from the outside of a cylindrical membrane support with γ-alumina interlayer (the membrane side), and oxygen gas was fed from the inside (the support side). Extended counter-diffusion CVD is a method of depositing silica films under highly pressurized conditions applied to the membrane side where TMOS is supplied. Two silica membranes were deposited for 10 h at 573 K under differential pressures of 0.1 MPa and 0.0 MPa applied between the cylindrical membranes. The hydrogen permeances for these silica membranes were unaffected (5 × 10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ at 573 K), although the methane and carbon dioxide permeances were greatly reduced for dense silica films prepared by high-pressure CVD (HPCVD). Therefore, the selectivity of hydrogen over methane and carbon dioxide was 24,000, and 1200, respectively. It is suggested from energy dispersive X-ray microanalysis (EDX) observations in scanning electron microscopy (SEM) and scanning probe microscopy (SPM) results that this high selectivity was due to the reduced number of defects and/or pinholes formed in the dense silica membranes by HPCVD.     

Physicochemical properties and desulfurization activities of metal oxide/biomass-based activated carbons prepared by blending method

Column activated carbons were prepared from walnut shell chars and transition metal oxide powders (i.e. Co₂O₃, Ni₂O₃, CuO and V₂O₅) with blending method. Samples were characterized by N₂ adsorption–desorption, X-ray diffraction, X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy. The texture properties of all modified activated carbons with metal oxides dosage of <5 wt% did not change evidently. The basic functionalities of these activated carbons increased relative to blank carbon. Moreover, metal species with different oxidation states coexisted on the modified activated carbons. The optimal dosage of all metal oxides was 2 wt%. The sulfur capacities of these modified activated carbons were 7.7–46.0 % higher than that of blank activated carbon and the highest occurred for V₂O₅ modified activated carbon. The improved desulfurization performance was mainly attributed to the higher catalytic activity of the active metal oxides formed in the presence of O₂ during the desulfurization process.     

称量法制备气体标准物质称量不确定度评定的简化方法

气体标准物质作为保证分析测量结果准确性的计量标准而在科学研究、环境检测、医疗卫生、石油化工、电力、煤炭、机械等国民经济的各个领域得到广泛的应用.其制备方法多种多样,目前国际上通用的配气方法有分压法[1]、静态容量法[2]、称量法[3]和动态容积法[4]等.称量法是以国际单位制基本单位质量作为基准的绝对方法,它具有最高的准确度,是国际上公认的基准方法.国际标准化组织也出版了相应的标准(ISO 6142-2001) [5]以对称量法配气进行规范.     

Ni catalysts supported on nano-crystalline aluminum oxide prepared by a microemulsion method for dry reforming reaction

Mesoporous nano-crystalline γ-Al₂O₃ with high surface area prepared by a microemulsion (ME) method was employed as carrier for nickel catalysts in dry reforming of methane for syngas production. The structural properties of the catalysts were characterized by X-ray diffraction, Brunauer–Emmett–Teller surface area analysis, temperature programmed reduction and oxidation and scanning electron microscopy techniques. Microemulsion showed it to be a promising way for the production of nano-crystalline aluminum oxide, and the nickel catalysts prepared with this support have significant features and properties to use in the dry reforming reaction. The results revealed that the prepared γ-Al₂O₃ exhibited a nano-crystalline structure (crystal size: c.4.8 nm) with a high specific surface area (308 m² g^?1). In addition, the catalysts with different nickel contents exhibited high catalytic activity in the dry reforming reaction. The results also showed that an increase in Ni loading from 5 to 15 wt% caused a decrease in the specific surface area and nickel dispersion.