Selective separation of silver(I) and mercury(II) ions in natural water samples using alumina modified thiouracil derivatives as new solid phase extractors

A simple and reliable solid-phase extraction (SPE) method has been developed to synthesise two new sorbents: 6-propyl-2-thiouracil and 5,6-diamino-2-thiouracil physically loaded onto alumina surface, phases I and II, respectively. The synthesis of these new phases has been confirmed by IR-spectroscopy. The surface concentrations of the organic moieties were determined to be 0.182 and 0.562 mmol g^?1 for phases I and II, respectively. The evaluation of the selectivity and metal uptake properties incorporated in these two alumina phases were also studied and discussed for 10 different metal ions: Ca(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II), Hg(II), Pb(II) and Ag(I) under different controlling factors. The data obtained clearly indicated that the new SP-extractors have the highest affinity for retention of Hg(II) ions. Selective separation of Hg(II) from Ag(I) as one of the most interfering ion, in addition to the other eight coexisting metal ions under investigation, was achieved successfully using the new sorbents at pH = 9.0 under static conditions. Therefore, Hg(II) exhibits major retention percentage (100.0%) using phase I or II. However, Ag(I) exhibits minor retention percentage equal to 1.33% using phase I and 0.67% using phase II. On the other hand, the retention percentage of the other eight metal ions ranged (0.0–3.08%) using phase I and (0.0–1.54%) using phase II at the same pH. The new phases were applied for separation and determination of trace amounts of Hg(II) and Ag(I) spiked natural water samples using cold vapour atomic absorption spectroscopy and atomic absorption spectroscopy with no matrix interference. The high recovery values of Hg(II) and Ag(I) obtained using phases I and II were ranged 98.9 ± 0.1–99.2 ± 0.05% along with a good precision (RSD% 0.01–0.502%, N = 3) demonstrate the accuracy and validity of the new sorbents for separation and determination of Hg(II) and Ag(I).     

Nanometer SiO2 modified with 5-sulfosalicylic acid as selective solid-phase extractant for Fe(III) determination by ICP-AES from biological and natural water samples

A new modified nanometer SiO₂ using 5-sulfosalicylic acid (SSA) as a solid-phase extractant was used for separation, preconcentration and determination of Fe(III) in aqueous solutions by inductively coupled plasma atomic emission spectrometry (ICP-AES). Its adsorption and preconcentration behaviour for Fe(III) in aqueous solutions was investigated using static procedures in detail. The optimum pH value for the separation of Fe(III) on the newly designed sorbent was 3.5. Complete elution of the adsorbed Fe(III) from the nanometer SiO₂-SSA was carried out using 2.0 mL of 0.01 mol L^− 1 of HCl. The time of 90% sorption was less than 2 min for Fe(III) at pH 3.5. Common coexisting ions did not interfere with the separation and determination of Fe(III) at pH 3.5. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 44.01 mg of Fe(III) per gram of sorbent. The relative standard deviation (RSD) of the method under optimum conditions was 3% (n = 5). The procedure was validated by analyzing three certified reference materials (GBW 08301, GBW 08504, GBW 08511), the results obtained were in good agreement with standard values. The nanometer SiO₂-SSA was successfully employed in the separation and preconcentration of the investigated Fe(III) from the biological and natural water samples yielding 100-folds concentration factor.     

Development of a broad selective molecularly imprinted polymers-based solid phase extraction of contraceptive drug levonorgestrel from water samples

A broad selective molecularly imprinted polymers-based solid phase extraction (MISPE) for levonorgestrel (LNG) from water samples was developed. Using LNG as a template molecule, acrylamide (AA) as functional monomer, ethylene glycol dimethacrylate (EGDMA) as linking agent and bulk polymerisation as a synthetic method, the molecularly imprinted polymers (MIPs) were synthesised and characterised. The MIPs displayed a high specific rebinding for LNG with the imprinting factor of 3.71. The Scatchard analysis showed that there was at least one class of binding site for LNG formed in the MIPs with the dissociation constant of 8.046?µg?mL^?1. The results of selectivity testing indicated that the MIPs also exhibited high cross-reactivity with structurally related compounds (estrone, methylprednisolone and ethinyl estradiol), but no recognition with non-structurally related compound (indomethacin), suggesting that the MIPs could be used as a broad recognition absorbent. MISPE column was prepared by packing MIPs particles into a common SPE cartridge. The MISPE extraction conditions including loading, washing and eluting solutions were carefully optimised. Water samples spiked with LNG were extracted by MISPE column and detected by high-performance liquid chromatography. The recoveries were found to be 79.97?～?132.79% with relative standard deviations (RSD) of 1.92?～?10.43%, indicating the feasibility of the prepared MIPs for LNG extraction.     

Uses of 5-Methylresorcin-bonded polyurethan foam as a new solid phase extractor for the selective separation of mercury ions from natural water samples

In this work, 5-Methylresorcin (MR) bonded to untreated polyurethane foam (PUF) was successfully employed as a sorbent (MR-PUF) for the selective separation and determination of mercury in natural water samples. Mercury can be quantitatively recovered in the pH range of 5-7. The system presented a minicolumn packed with the new sorbent, where the sample solution was passed through it for a period of time and an eluent solution stripped out the retained mercury, which was further determined with dithizone. The new matrix was characterized by using different tools (IR spectra, stability and density). The kinetics of mercury uptake by the new matrix was found to be fast, reaching equilibrium in 20 minutes. A preconcentration factor of 350 was achieved. The proposed preconcentration procedure was applied successfully to the selective separation and determination of trace mercury in natural water samples.      

Selective solid-phase extraction of trace Fe(III) from biological and natural water samples using nanometer SiO2 modified with acetylsalicylic acid

A new method using acetylsalicylic acid (aspirin) modified SiO₂ nanoparticles (nanometer SiO₂-aspirin) as a solid-phase extractant (SPE) has been developed for the preconcentration of trace amounts of Fe(III) prior to their determination by inductively coupled plasma optical emission spectrometry. The preconcentration conditions of analytes were investigated, including the pH value, the shaking time, the mass of sorbent, the sample flow rate and volume, the elution condition and the interfering ions. At pH 4, the sorption capacity of nanometer SiO₂-aspirin was found to be 1.28 mmol g⁻¹. The preconcentration factor is 50. The detection limit (3σ) for Fe(III) was 0.49 ng mL⁻¹. The method was validated by analyzing two certified reference materials (GBW 08301, river sediment and GBW 08303, polluted farming soil), and the results obtained are in good agreement with standard values. The method was also applied to the determination of trace Fe(III) in biological and water samples with satisfactory results. Correspondence: Xiangbing Zhu, Department of Chemistry, Lanzhou University, Lanzhou 730000, P.R. China     

On-line solid-phase extraction and multisyringe flow injection analysis of Al(III) and Fe(III) in drinking water

A new analytical method was developed for on-line monitoring of residual coagulants (aluminium and iron salts) in potable water. The determination was based on a sequential procedure coupling an extraction/enrichment step of the analytes onto a modified resin and a spectrophotometric measurement of a surfactant-sensitized binary complex formed between eluted analytes and Chrome Azurol S. The optimization of the solid phase extraction was performed using factorial design and a Doehlert matrix considering six variables: sample percolation rate, sample metal concentration, flow-through sample volume (all three directly linked to the extraction step), elution flow rate, concentration and volume of eluent (all three directly linked to the elution step). A specific reagent was elaborated for sensitive and specific spectrophotometric determination of Al(III) and Fe(III), by optimizing surfactant and ligand concentrations and buffer composition. The whole procedure was automated by a multisyringe flow injection analysis (MSFIA) system. Detection limits of 4.9 and 5.6 μg L⁻¹ were obtained for Al(III) and Fe(III) determination , respectively, and the linear calibration graph up to 300 μg L⁻¹ (both for Al(III) and Fe(III)) was well adapted to the monitoring of drinking water quality. The system was successfully applied to the on-site determination of Al(III) and Fe(III) at the outlet of two water treatment units during two periods of the year (winter and summer conditions).     

Ion-pair adsorption film colorimetry of iron (III) in water samples and human serum

The anionic chelate of iron(III)-2,2-dihydroxyazobenzene (H₂L), [FeL₂]^–, formed 1 1 ion-pair with crystal violet cation (CV⁺), CV⁺ [FeL₂]^–, and was adsorbed on a surface of transparent polyvinyl chloride (PVC) film plasticized with di-n-octyl phthalate. Enrichment of the blue violet species of the ion-pair onto the transparent PVC film has enabled a highly sensitive and simple method for the determination of iron(III). The detection limits are 1 × 10^–8 mol dm^–3 (0.6 ppb) by spectrophotometry at 592 nm, and 4 × 10^–8 mol dm^–3 (2 ppb) by visual colorimetry. The method has been successfully applied to the determination of iron in water samples and human serum. No preparatory procedures for the separation of serum protein and other coexisting substances are required, since ion-pair adsorption process provides a new method to prevent interference of serum matrix.     

Construction and characterization of nano iron complex ionophore for electrochemical determination of Fe(III) in pure and various real water samples

Electrochemical methods represent an important class of widely used techniques for the detection of metal ions. The unique chemical and physical properties of nanoparticles make them extremely suitable for designing new and improved sensing devices, especially electrochemical sensors and biosensors. This study focused on the synthesis of a nano‐Fe(III)–Sud complex and its characterization using various spectroscopic and analytical tools, optimized using the density functional theory method, screened for antibacterial activity and evaluated for possible binding to DNA using molecular docking study. Proceeding from the collected information, nano‐Fe(III)–Sud was used further for constructing carbon paste and screen‐printed ion‐selective electrodes. The proposed sensors were successfully applied for the determination of Fe(III) ions in various real and environmental water samples. Some texture analyses of the electrode surface were conducted using atomic force microscopy. At optimum values of various conditions, the proposed electrodes responded towards Fe(III) ions linearly in the range 2.5 × 10^?9–1 × 10^?2 and 1.0 × 10^?8–1 × 10^?2 M with slope of 19.73 ± 0.82 and 18.57 ± 0.32 mV decade^?1 of Fe(III) ion concentration and detection limit of 2.5 × 10^?9 and 1.0 × 10^?8 M for Fe(III)–Sud‐SPE (electrode I) and Fe(III)–Sud‐CPE (electrode II), respectively. The electrode response is independent of pH in the range 2.0–7.0 and 2.5–7.0, with a fast response time (4 and 7 s) at 25°C for electrode I and electrode II, respectively. Moreover, the electrodes also showed high selectivity and long lifetime (more than 6 and 3 months for electrode I and electrode II, respectively). The electrodes showed good selectivity for Fe(III) ions among a wide variety of metal ions. The results obtained compared well with those obtained using atomic absorption spectrometry.     

A new efficient adsorbent in the preconcentration studies of the Cr(III) and Fe(III) ions

In this study, the imine‐graphene hybrid material (HM) was used as an adsorbent for removal of Fe(III) and Cr(III) metal ions from the drinking waters. The adsorbent material (HM) was prepared at three steps. At the first step, the graphite was oxidized by Hummer's method for preparation of graphene oxide (GO), in the second step, the silanization derivative (GO‐APTES) was obtained from the reaction of the 3‐(trimethoxysilyl) propylamine and GO. In the final step, the hybrid material (HM) was synthesized from the reaction of the 3,5‐diiodosalicylaldehyde and GO‐APTES. The chemical structures of three materials GO, GO‐APTES and HB were characterized by using the FT‐IR, XRD, EDX, SEM, TEM and UV‐vis methods. Thermal properties of the materials GO, GO‐APTES and HB were investigated by TGA/DTA methods in the 25–1000°C temperature range. Adsorption and desorption studies of the hybrid material toward Fe(III) and Cr(III) metal ions were investigated using the Batch method. The effect of pH, contact time, temperature, concentration on the adsorption properties of the hybrid material were investigated by ICP‐OES. The Fe(III) and Cr(III) ions have the maximum adsorption at the pH 7. The adsorption capacity decreases with the increase in pH values because above pH 9 the adsorption decreases due to the precipitation of metal hydroxide.     

Treated Rice Bran for Scavenging Cr(III) and Hg(II) from Acidic Solution

The purpose of this study was to examine the efficiency with which rice bran (treated or untreated) removes heavy metals, especially Cr(III) and Hg(II), from acidic solution. Sorption assays were done in shaken flasks in the presence of rice bran. Different experimental conditions such as pH, volume of solution, bran weight, particle size, exchange time and stirring time were improved. The efficiency of bran was studied before and after treatments. For treatment, solutions of acid, alkali and salt were used. The results show that after treating with 4 M sodium chloride solution, its efficiency in removal of Cr(III) and Hg(II) was improved. Kinetic measurements of chromium and mercury removal by bran have revealed that sorption equilibrium was obtained after 10 min of contact. Sorption experiments done with various granulometric fractions of rice bran have shown that this sorbent has the same efficiencies in meshes higher than 20. Further research is necessary in order to determine a mechanism for cations removal by the bran. It is mentioned that the process of making polished rice from brown rice discharges rice bran; therefore, it is very inexpensive, with a cost of 1/50 ? 1/40 of that of synthetic sorbent, and thus its use would significantly lower the cost of wastewater treatment.     

Influence of the chain and layer structure of Fe(III) and In(III) aqua-pentachloro-complexes on the bending vibrations of water molecules

Studies of IR and Raman spectra of monohydrates M^I₂[M^IIICl₅(H₂O)] (where M^I=K⁺, Rb⁺, Cs⁺ and M^III=Fe³⁺, In³⁺) at 1400-1900 cm⁻¹ have been carried out. The medium intensity band, detected in the region 1580-1595 cm⁻¹ was assigned to bending vibrations of water molecules (δHOH). The shift of the δHOH band towards low wavenumbers (1580-1595 cm⁻¹) is a main sign of the water molecule interactions in the chain hydrates. Additionally in the IR and Raman spectra of these salts, the appearance of the low intensity band between 1750 and 1810 cm⁻¹ (ν_x(H₂O)) was observed. In the presented paper we also discuss the influence of M^I and M^III cations on the position and splitting of these bands.     

Bacterial sensitivity and SOD behavior of N-pyrone glucosamine Schiff base Fe(III) complex: conjoint experimental-DFT evaluation

Iron and sugar are essential components of life processes. In the evident interest toward Fe(III) compounds to explore the ability of sugars toward metallotherapy, a systematic hyphenated DFT-experimental study of a novel sugar Schiff base Fe(III) complex of general composition [Fe(L)(OH)], where L = N-dehydroacetic acid-glucosamine (dha-glsH₂), is presented. Based on various experimental spectrometric and spectroscopic characterization techniques in combination with theoretical data, a suitable distorted tetragonal structure is suggested for the complex. In addition to the formulation of the synthesized complex, superoxide dismutase (SOD) mimetic, and antimicrobial actions have also been the active goal of the work. A promising superoxide dismutazing potential with IC₅₀ = 69 μM was found. But on the other hand antibacterial action of the complex has shown less sensitivity to be called as efficient bactericidal agent.     

Removal of Cu(II), Zn(II) and Co(II) ions from aqueous solutions by adsorption onto natural bentonite

In this study, the removal of Cu(II), Zn(II) and Co(II) ions from aqueous solutions using the adsorption process onto natural bentonite has been investigated as a function of initial metal concentration, pH and temperature. In order to find out the effect of temperature on adsorption, the experiments were conducted at 20, 50, 75 and 90 °C. For all the metal cations studied, the maximum adsorption was observed at 20 °C. The batch method has been employed using initial metal concentrations in solution ranging from 15 to 70 mg L⁻¹ at pH 3.0, 5.0, 7.0 and 9.0. A flame atomic absorption spectrometer was used for measuring the heavy metal concentrations before and after adsorption. The percentage adsorption and distribution coefficients (K _d) were determined for the adsorption system as a function of adsorbate concentration. In the ion exchange evaluation part of the study, it is determined that in every concentration range, adsorption ratios of bentonitic clay-heavy metal cations match to Langmuir, Freundlich and Dubinin-Kaganer-Radushkevich (DKR) adsorption isotherm data, adding to that every cation exchange capacity of metals has been calculated. It is shown that the bentonite is sensitive to pH changes, so that the amounts of heavy metal cations adsorbed increase as pH increase in adsorbent-adsorbate system. It is evident that the adsorption phenomena depend on the surface charge density of adsorbent and hydrated ion diameter depending upon the solution pH. According to the adsorption equilibrium studies, the selectivity order can be given as Zn²⁺>Cu²⁺>Co²⁺. These results show that bentonitic clay hold great potential to remove the relevant heavy metal cations from industrial wastewater. Also, from the results of the thermodynamic analysis, standard free energy ΔG ⁰, standard enthalpy ΔH ⁰ and standard entropy ΔS ⁰ of the adsorption process were calculated.     

New method for simultaneous determination of Fe(II) and Fe(III) in water using flow injection technique

The method exploits the possibilities of flow injection gradient titration in a system of reversed flow with spectrophotometric detection. In the developed approach a small amount of titrant (EDTA) is injected into a stream of sample containing a mixture of indicators (sulfosalicylic acid and 1,10-phenanthroline). In acid environment sulfosalicylic acid forms a complex with Fe(III), whereas 1,10-phenanthroline forms a complex with Fe(II). Measurements are performed at wavelength λ = 530 nm when radiation is absorbed by both complexes. After injection EDTA replaces sulfosalicylic acid and forms with Fe(III) more stable colourless complex. As a result, a characteristic “cut off” peak is registered with a width corresponding to the Fe(III) concentration and with a height corresponding to the Fe(II) concentration. Calibration was performed by titration of four two-component standard solutions of the Fe(II)/Fe(III) concentrations established in accordance with 2² factorial plan. The method was tested with the use of synthetic samples and then it was applied to the analysis of water samples taken from artesian wells. Under optimized experimental conditions Fe(II) and Fe(III) were determined with precision less than 0.8 and 2.5% (RSD) and accuracy less than 3.2 and 5.1% (relative error) within the concentration ranges of 0.1-3.0 and 0.9-3.5 mg L⁻¹ of both analytes, respectively.     

A novel ion selective membrane potentiometric sensor for direct determination of Fe(III) in the presence of Fe(II)

A new PVC membrane potentiometric sensor that is highly selective to Fe(III) ions was prepared by using 2-[(2-hydroxy-1-propenyl-buta-1,3-dienylimino)-methyl]-4-p-tolylazo-phenol [HPDTP] as a suitable carrier. The electrode exhibits a linear response for iron(III) ions over a wide concentration range (3.5 × 10⁻⁶ to 4.0 × 10⁻²) with a super Nernstian slope of 28.5 (±0.5) per decade. The electrode can be used in the pH range from 4.5 to 6.5. The proposed sensor shows fairly a good discriminating ability towards Fe³⁺ ion in comparison to some hard and soft metals such as Fe²⁺, Cd²⁺, Cu²⁺, Al³⁺ and Ca²⁺. It has a response time of <15 s and can be used for at least 2 months without any measurable divergence in response characteristics. The electrode was used in the direct determination of Fe³⁺ in aqueous samples and as an indicator electrode in potentiometric titration of Fe(III) ions.     

Synthesis of nano-pore samarium (III)-imprinted polymer for preconcentrative separation of samarium ions from other lanthanide ions via solid phase extraction

A batch process was developed to separate samarium ions from some lanthanide ions by a novel solid phase which was prepared via the ion-imprinting technique. The samarium (III) ion-imprinted polymer (IIP) particles were synthesized by preparing the ternary complex of samarium ions with 5,7-dichloroquinoline-8-ol (DCQ) and 4-vinylpyridine (VP). Then, thermally copolymerization with styrene (functional monomer, STY) and divinylbenzene (cross-linking monomer, DVB) followed in the presence of 2-methoxy ethanol (porogen) and 2,2′-azobisisobutyronitrile (initiator, AIBN). The imprinted ion was removed by stirring the above particles with 50% (v/v) HCl to obtain the leached IIP particles. Moreover, control polymer (CP) particles were similarly prepared without the samarium ions. The unleached and leached IIP particles were characterized by X-ray diffraction (XRD), infra-red spectroscopy (IR), thermo gravimetric analysis (TGA) and scanning electron microscopy (SEM). Finally, preconcentration and selectivity studies for samarium and the other lanthanide ions were carried out. The preconcentration of the samarium (III) traces was studied during rebinding with the leached IIP particles as a function of pH, the weight of the polymer material, the preconcentration and the elution times, the eluent volume and the aqueous phase volume. These studies indicated that the samarium (III) amount as low as 1 μg, present in 200 mL, could be preconcentrated into 25 mL of 1.0 M HCl.     

Degradation of carbofuran in aqueous solution by Fe(III) aquacomplexes as effective photocatalysts

The photodegradation of carbofuran by excitation of iron(III) aquacomplexes was investigated under UV irradiation. The degradation rate was strongly influenced by the pH, and initial concentration of Fe(III). The degradation efficiency of carbofuran at the difference pH was in good agreement with the initial concentration of Fe(OH)²⁺ in the solution. An initial carbofuran concentration of 10 mg L⁻¹ was completely degraded within 50 min at pH 2.8 with original Fe(III) concentration of 8 × 10⁻⁴ mol L⁻¹. This degradation reaction was found to follow the first order kinetics law and the rate constant of 1.60 × 10⁻³ s⁻¹ was observed. The decrease of TOC content was observed during the photocatalytic process and the removal percentage obtained was about 70% after 25 h. Furthermore, ammonium ion as an end-product was detected in the solution. Therefore, this process based on the catalytic reaction of Fe(II, III) is responsible for the continuous production of hydroxyl radicals in such system. A gas chromatography-mass spectrometry analysis showed the formation of four photoproducts, such as 2,2-dimethyl-2,3-dihydro-benzofuran-7-ol, etc., revealing that the carbamate branch, C-3 and C-2 positions in furan ring were attack targets of hydroxyl radicals. Based on these results, the photocatalytic system could be useful technology for the treatment and the mineralization of compounds like carbofuran.     

A facile fabrication of MOF for selective removal of chromium (III) from aqueous solution

A simple method for fabricating a metal organic framework (MOF: HKUST-1) as sorbent for selective removal of chromium (III) from aqueous solution is discussed. The structure and morphology of HKUST-1 was identified by fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), the powder X-ray diffraction (XRD) and N₂ adsorption-desorption (BET) analysis. Its removal process of chromium (III) and chromium (VI) on HKUST-1 was assessed systematically under various conditions such as pH value, shaking time and initial concentration of chromium (III). At pH 6.0–8.0, HKUST-1 were selective towards chromium (III) but hardly chromium (VI). Kinetic parameters fitted well with pseudo-second-order model and adsorption progress was described by Langmuir isotherm equations and spontaneous and endothermic according to the results of thermodynamics studies (?G?<?0, ?H?>?0, ?S?>?0).     

Silver modified magnetic carbon nanotubes composite as a selective solid phase extractor for preconcentration and determination of trace mercury ions in water solution

A magnetic composite of silver/iron oxides/carbon nanotubes (Ag/Fe₃O₄/CNTs) was synthesized and used as an adsorbent for the preconcentration of mercury ions in water solutions at room temperature (25°C) in this study. The silver nanoparticles were supported on the magnetic CNTs. The modification enabled the composite had not only a high adsorption capacity for mercury ions (Hg²⁺) but also the magnetic isolation properties. A fast, sensitive, and simple method was successfully developed for the preconcentration and determination of trace amount of Hg²⁺ in water using the synthesized nanocomposite as adsorbent. The mercury concentration was determined by an atomic fluorescence spectrometer (AFS). The experimental conditions such as pH value, extraction temperature, extraction time, sample volume, eluent composition and concentration, sorbent amount, and coexisting ions were investigated for the optimization. A 500 mL of sample volume resulted in a preconcentration factor of 125. When a 200 mL of sample was employed, the limit of detection for Hg²⁺ was as low as 0.03 ng mL^?1with relative standard deviation of 4.4% at 0.1 ng mL^?1 (n = 7). The ease of synthesis and separation, the good adsorption capacity, and the satisfactory recovery will possibly make the composite an attractive adsorbent for the preconcentration of ultratrace Hg²⁺ in waters.     

Solid-phase extraction of trace Cu(II) Fe(III) and Zn(II) with silica gel modified with curcumin from biological and natural water samples by ICP-OES

Silica gel was firstly functionalized with aminopropyltrimethoxysilane obtaining the aminopropylsilica gel (APSG). The APSG was reacted subsequently with curcumin yielding curcumin-bonded silica gel (curcumin-APSG). This new bonded silica gel was used for separation, pre-concentration and determination of Cu(II), Fe(III), Zn(II) in biological and natural water samples by inductively coupled plasma optical emission spectrometry (ICP-OES). Experimental conditions for effective adsorption of trace levels of metal ions were optimized with respect to different experimental parameters using batch and column procedures in detail. The optimum pH value for the separation of metal ions simultaneously on the newly sorbent was 4.0. Complete elution of the adsorbed metal ions from the sorbent surface was carried out using 2.0 mL of 0.1 mol L^− 1 of HCl. Common coexisting ions did not interfere with the separation and determination at pH 4.0. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 0.63, 0.46 and 0.37 mmol g^− 1 for Cu(II), Fe(III) and Zn(II) respectively. The time for 95% sorption for Cu(II) Fe(III) and Zn(II) was less than 2 min. The detection limits of the method defined by IUPAC was found to be 0.12, 0.15 and 0.40 ng mL^− 1 for Cu(II), Fe(III) and Zn(II), respectively. The relative standard deviation (RSD) of the method under optimum conditions was lower 3.0% (n = 5). The procedure was validated by analyzing the certified reference river sediment material (GBW 08301, China), the results obtained were in good agreement with standard values. This sorbent was successfully employed in the separation and pre-concentration of trace Cu(II), Fe(III) and Zn(II) from the biological and natural water samples yielding 75-fold concentration factor.