Electrochemical investigation of corrosion and corrosion inhibition of iron in hydrochloric acid solutions

The inhibition effect of 1-methyl pyrazole (MPA) on the acidic corrosion of iron in 1.0 M HCl was studied at different concentrations (10^?3–10^?2 M) by potentiodynamic polarization and electrochemical impedance spectroscopy, and EIS measurements. It is found from the polarization studies that methyl pyrazole (MPA) behaves mainly as anodic inhibitor in HCl. Values of polarization resistance (R_p) and double layer capacitance (C_dl) in the absence and presence of MPA in 1.0 M HCl are determined. The adsorption of MPA on iron surface from HCl is found to obey Temkin adsorption isotherm.     

Corrosion inhibition of carbon steel in hydrochloric acid 0.5 M by hexa methylene diamine tetramethyl-phosphonic acid

The efficiency of hexa methylene diamine tetra methyl-phosphonic acid (HMDTMP), as corrosion inhibitor for carbon steel in 0.5 M HCl, has been determined by gravimetric and electrochemical measurements. Polarization curves indicate that the compound is a mixed inhibitor, affecting both cathodic and anodic corrosion currents. Adsorption of HMDTMP derivatives on the carbon steel surface is in agreement with the Langmuir adsorption isotherm model, and the calculated Gibbs free energy value confirms the chemical nature of the adsorption. EIS results show that the charge in the impedance parameters (R_t and C_dl) with concentrations of HMDTMP is indicative. The adsorption of this molecule leads to the formation of a protective layer on carbon steel surface. The electrochemical results have also been supplemented by surface morphological studies.     

Corrosion inhibition of mild steel in hydrochloric acid by betanin as a green inhibitor

The effect of betanin (2,6-pyridinedicarboxylic acid, 4-(2-(2-carboxy-5-(beta-D-glucopyr-anosyloxy)-2,3-dihydro-6-hydroxy-1H-indol-1-yl)ethenyl)-2,3-dihydro-(S-(R*,R*))) on the corrosion inhibition of mild steel has been investigated in 1 M HCl solution. Weight loss method, potentiodynamic polarization, and electrochemical impedance spectroscopy techniques were applied to study the mild steel corrosion behavior in the absence and presence of different concentrations of betanin under the influence of various experimental conditions. The results obtained showed that betanin is a good “green” inhibitor for mild steel in 1 M HCl solution. Scanning electron microscopy observations of the steel surface confirmed the protective role of the inhibitor. The polarization curves showed that betanin behaves mainly as a mixed-type inhibitor. Maximum inhibition efficiency (98%) is obtained at betanin concentrations of 0.01 M. The results obtained from weight loss, polarization, and impedance measurements are in good agreement.     

On-line dilution and determination of the amount of concentrated hydrochloric acid in the final products from a hydrochloric acid production plant using a sequential injection titration system

An on-line sequential injection titration system for the determination of the concentration of concentrated hydrochloric acid as final product from a hydrochloric acid production plant is described. The system involves on-line dilution of the concentrated hydrochloric acid solution to an acceptable range for direct measurement by merging the sample stream with a de-ionized water diluent stream, followed by mixing in a dilution coil, before aspiration into the sequential injection system. Concentrated standard solutions were treated in exactly the same way as the samples. The system was evaluated for reproducibility, linearity, accuracy, and sample throughput. A linear relationship between peak width and logarithm of acid concentration was found in the range 5.934–8.995 mol l⁻¹ and a concentration of 0.005 mol l⁻¹ NaOH solution was used as titrant. Samples from the production plant showed excellent agreement when compared with the manual and automated batchwise titrations. The relative standard deviation was found to be less than 0.4% with a sample frequency of 30 samples per hour.     

Corrosion and corrosion inhibition characteristics of bulk nanocrystalline ingot iron in sulphuric acid

The corrosion and corrosion inhibition of bulk nanocrystalline ingot iron (BNII) fabricated from conventional polycrystalline ingot iron (CPII) by severe rolling was studied in 0.5 M H₂SO₄ solution using electrochemical impedance spectroscopy and potentiodynamic polarization techniques. The results indicate that BNII was more susceptible to corrosion in the acidic environment essentially because of an increase in the kinetics of the anodic reaction. An amino acid cysteine (cys) was employed as a corrosion inhibitor at concentrations of 0.001 and 0.005 M. Tests in inhibited solutions revealed that cys reduced the corrosion rates of both metal specimens by different mechanisms. For CPII cys inhibited the cathodic reaction but had a stimulating effect on the anodic process at low concentration and a trivial effect at higher concentration. For BNII, cys inhibited both the cathodic and the anodic reactions, although the former effect was more pronounced. Iodide ions improved the inhibitive effect of cys without altering the inhibition mechanism.     

红四氮唑在盐酸介质中对冷轧钢的缓蚀作用

用失重法、电化学法和原子力显微镜（AFM）研究了红四氮唑在1.0 mol/L ~ 5.0 mol/L HCl介质中对冷轧钢的缓蚀作用。结果表明：红四氮唑对冷轧钢具有良好的缓蚀作用,为混合抑制型缓蚀剂,且在钢表面的吸附符合Langmuir吸附模型;并通过吸附热力学和动力学参数详细讨论了缓蚀作用机理;AFM测试结果表明红四氮唑在钢表面吸附形成了致密的缓蚀剂膜层。     

On the corrosion inhibition of iron in hydrochloric acid solutions,Part I: Electrochemical DC and AC studies

The inhibitive action of 4-methyl pyrazole (4MP) against the corrosion of iron (99.9999%) in solutions of hydrochloric acid has been studied using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). At inhibitor concentration range (10^?3–10^?2 M) in 1.0 M acid, the results showed that 4MP suppressed mainly the anodic processes of iron corrosion in 1.0 M HCl by adsorption on the iron surface according to Temkin adsorption isotherm. Both potentiodynamic and EIS measurements reveal that 4MP inhibits the iron corrosion in 1.0 M HCl and that the efficiency increases with increasing inhibitor concentration. Data obtained from EIS were analyzed to model the corrosion inhibition process through an equivalent circuit.     

Corrosion inhibition of mild steel in hydrochloric acid using extract of glycine max leaves

Research on Chemical Intermediates - The activity of glycine max leaves extract against corrosion of mild steel in 0.5 M HCl solution has been investigated at different temperatures...     

Study on the inhibition of mild steel corrosion by 1,3-bis-(morpholin-4-yl-phenyl-methyl)-thiourea in hydrochloric acid medium

1,3-Bis-(morpholin-4-yl-phenyl-methyl)-thiourea (MBT) was synthesized and their influence on the inhibition of corrosion on mild steel in various hydrochloric acid concentrations has been investigated by weight loss, potentiodynamic polarization, electrochemical impedance (EI), Tafel polarization, scanning electron microscope (SEM) and FT-IR methods. The result of weight loss study shows that the corrosion inhibition efficiency (IE) is directly proportional to the concentration of the inhibitor and inversely proportional to the temperature. Electrochemical study proved that the inhibitor acts as a mixed type inhibitor. SEM shows the formation of a protective film of the inhibitor on the mild steel. The IR data also provide evidence for the anticorrosion effect of the inhibitor.     

Corrosion inhibition and mechanism of mild steel in hydrochloric acid by ceftriaxone and amoxicillin

Corrosion inhibition of mild steel in 1 mol/L HCl by amoxicillin and ceftriaxone in the concentration range of 1.00×10-5-1.00×10-2 mol/L has been studied using weight loss,electrochemical potentiodynamic polarization,electrochemical impedance spectroscopy(EIS),scanning electron microscopy(SEM) and quantum chemistry tests at 298 K.The weight loss experiment showed that the inhibition efficiency increased with amoxicillin and ceftriaxone concentrations to attain the maximums of 80.3% and 94.1%,respectively at...     

氯化硝基四氮唑蓝对钢在盐酸溶液中的缓蚀作用

采用失重法、动电位极化曲线、电化学阻抗谱(EIS)和扫描电子显微镜(SEM)研究了氯化硝基四氮唑蓝(NTBC)在1.0-5.0mo·lL-1HCl溶液中对冷轧钢(CRS)的缓蚀作用.结果表明:NTBC在1.0mo·lL-1HCl溶液中对冷轧钢具有良好的缓蚀作用,且在钢表面的吸附符合Langmuir吸附等温式.缓蚀率随缓蚀剂浓度的增加而增大,但随盐酸浓度和温度的增加而减小.求出了相应的吸附热力学(吸附自由能ΔG0,吸附焓ΔH0,吸附熵ΔS0)和腐蚀动力学参数(腐蚀速率常数k,动力学常数B),并根据这些参数讨论了缓蚀作用机理.动电位极化曲线表明:NTBC为混合抑制型缓蚀剂;EIS谱在高频区呈容抗弧,在低频区出现感抗弧,电荷转移电阻随缓蚀剂浓度的增加而增大.SEM再次表明NTBC对钢在盐酸介质中的腐蚀产生了明显的抑制作用.     

Corrosion inhibition performance of tannins for mild steel in hydrochloric acid solution

Research on Chemical Intermediates - The corrosion inhibition behavior of commercial hydrolysable tannin (tara tannin), condensed tannin (black wattle tannin) and complex tannin (bayberry tannin)...     

Interactions and corrosion mitigation prospective of pyrazole derivative on mild steel in HCl environment

The effectiveness of 1H?pyrazole?3,5?dicarboxylic acid 5?benzyl ester 3?phenyl ester (PCBPE) as a preventer for deterioration of IS 513 Gr. D steel in 1 M HCl medium is evaluated via weight loss, electrochemical impedance, and polarization techniques. Kinetic and thermodynamic parameters assessed the feasibility of the adsorption process at diverse temperatures. The inhibition action on mild steel has been enhanced with increasing PCBPE concentration. It is found from the polarization studies that PCBPE behaves as mixed type inhibitor in HCl medium. The adsorption process of PCBPE on mild steel surface from acid environment is favoured Langmuir adsorption isotherm. The shielding efficiency of PCBPE has been enhanced at elevated concentrations, and it has been diminished at amplified temperatures. The Atomic Force Microscope (AFM), Scanning Electron Microscope (SEM), and Energy Dispersive Spectrum (EDS) were used to establish a surface characterization of metal specimens. A quantum chemical analysis of electron density distributions in the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) demonstrated how the inhibitor undergoes adsorption on mild steel in 1 M HCl. All experimental findings substantiate the corrosion mitigation performance of PCBPE on mild steel in acidic environments.     

竹叶提取物对铝在HCl溶液中的缓蚀作用

用不同浓度的C₂H₅OH（体积分数：20%-80%）从金竹竹叶中提取制备出竹叶缓蚀剂（简称为PSLE）,用紫外-可见（UV-Vis）光谱和傅里叶变换红外（FTIR）光谱对其进行了表征,并对总黄酮含量进行了测定. 采用失重法、动电位极化曲线、电化学阻抗谱（EIS）和扫描电子显微镜（SEM）研究PSLE在HCl 介质中对铝的缓蚀作用.采用量子化学密度泛函理论（DFT）研究了两个主要竹叶黄酮成分牡荆苷和异牡荆苷的吸附方式. 结果表明：PSLE对铝具有良好的缓蚀作用,且在铝表面的吸附符合Langmuir 吸附等温式. 缓蚀率随其浓度的增加而增大,但随温度的升高和盐酸浓度的增加而降低. 竹叶总黄酮含量和竹叶缓蚀剂的缓蚀性能有良好的相关性,初步推测竹叶缓蚀剂的有效成分主要为竹叶黄酮类化合物. PSLE为阴极抑制型缓蚀剂;EIS 在高频区呈容抗弧,在低频区呈感抗弧,添加PSLE后,阻抗值显著增大. SEM表明添加PSLE对铝的腐蚀产生了明显的抑制作用.量子化学计算结果表明,牡荆苷和异牡荆苷的吸附中心主要集中在竹叶黄酮骨架（FBS）.     

竹叶提取物对铝在HCI溶液中的缓蚀作用

用不同浓度的C2H5OH(体积分数:20％-80％)从金竹竹叶中提取制备出竹叶缓蚀剂(简称为PSLE),用紫外-可见(UV-Vis)光谱和傅里叶变换红外(FTIR)光谱对其进行了表征,并对总黄酮含量进行了测定.采用失重法、动电位极化曲线、电化学阻抗谱(EIS)和扫描电子显微镜(SEM)研究PSLE在HCI介质中对铝的缓蚀作用.采用量子化学密度泛函理论(DFT)研究了两个主要竹叶黄酮成分牡荆苷和异牡荆苷的吸附方式.结果表明:PSLE对铝具有良好的缓蚀作用,且在铝表面的吸附符合Langmuir吸附等温式.缓蚀率随其浓度的增加而增大,但随温度的升高和盐酸浓度的增加而降低.竹叶总黄酮含量和竹叶缓蚀剂的缓蚀性能有良好的相关性,初步推测竹叶缓蚀剂的有效成分主要为竹叶黄酮类化合物.PSLE为阴极抑制型缓蚀剂;EIS在高频区呈容抗弧,在低频区呈感抗弧,添加PSLE后,阻抗值显著增大.SEM表明添加PSLE对铝的腐蚀产生了明显的抑制作用.量子化学计算结果表明,牡荆苷和异牡荆苷的吸附中心主要集中在竹叶黄酮骨架(FBS).     

曲酸对马铃薯酪氨酸酶的抑制作用研究

曲酸等几种化合物对马铃薯酪氨酸酶的抑制作用表明：巯基类化合物、抗坏血酸和曲酸具有较强的抑制作用。预水浴温度和时间对曲酸的抑制作用并没有显著影响,曲酸通过延长L-tyrosine加氧羟化的迟滞时间,从而抑制单酚酶活性,以L—DOPA为底物测得曲酸为竞争性抑制,抑制常数艏为0．17mM。紫外光谱表明曲酸能将二酚酶催化的产物o-醌还原成二酚,从而抑制黑色素的生成。     

Impedance spectroscopic study of corrosion inhibition of Al-Pure by organic Schiff base in hydrochloric acid

A new corrosion inhibitor namely o-Chloroaniline-N-benzylidene (o-CANB) has been synthesized and its inhibitive performance toward the corrosion of Al-Pure in 1.0 M hydrochloric acid has been investigated. Corrosion inhibition was studied by chemical method (weight loss) and electrochemical techniques including polarization method and electrochemical impedance spectroscopy (EIS). The present study has shown that this inhibitor is good in acidic media and the inhibition efficiency up to >99% in 1.0 M HCl. Polarization measurement revealed that the investigated inhibitor is a mixed type with a predominant action on cathode. Impedance measurement showed that the charge transfer resistance (R_ct) increased and double layer capacitance (C_dl) decreased with an increase in the inhibitor's concentration. Obtained results about inhibition efficiency from weight loss, polarization study and EIS are in good agreement with each other. The adsorption of the inhibitor on the metal surface in the acid solution was found to obey Langmuir's adsorption isotherm.     

MMI作为铜的盐酸酸洗缓蚀剂作用机理的研究

用失重法研究了N-甲基-2-巯基咪唑（MMI）在5％盐酸中对铜的酸洗缓蚀性能.探讨了温度和MMI浓度对缓蚀效果的影响，从中得出了MMI在铜表面的吸附等温式，计算了吸附热及MMI的加入对铜在盐酸中腐蚀反应活化能的影响，进而探讨了MMI对铜缓蚀作用的机理.结果表明， 30 ℃下，在5％盐酸中，当MMI的浓度在3 mmol•L－1和8 mmol•L－1之间时,缓蚀率随MMI浓度的增加而迅速增加，当浓度达到8 mmol•L－1时，缓蚀率趋于定值，而当浓度小于3 mmol•L－1时， MMI的加入会加速铜的腐蚀；吸附在铜表面的MMI分子间的作用力整体表现为引力； MMI在铜表面的吸附是吸热反应； MMI的加入降低了铜的腐蚀反应活化能.     

竹叶提取物对铝在HCl溶液中的缓蚀作用(英文)

用不同浓度的C2H5OH(体积分数:20%-80%)从金竹竹叶中提取制备出竹叶缓蚀剂(简称为PSLE),用紫外-可见(UV-Vis)光谱和傅里叶变换红外(FTIR)光谱对其进行了表征,并对总黄酮含量进行了测定.采用失重法、动电位极化曲线、电化学阻抗谱(EIS)和扫描电子显微镜(SEM)研究PSLE在HCl介质中对铝的缓蚀作用.采用量子化学密度泛函理论(DFT)研究了两个主要竹叶黄酮成分牡荆苷和异牡荆苷的吸附方式.结果表明:PSLE对铝具有良好的缓蚀作用,且在铝表面的吸附符合Langmuir吸附等温式.缓蚀率随其浓度的增加而增大,但随温度的升高和盐酸浓度的增加而降低.竹叶总黄酮含量和竹叶缓蚀剂的缓蚀性能有良好的相关性,初步推测竹叶缓蚀剂的有效成分主要为竹叶黄酮类化合物.PSLE为阴极抑制型缓蚀剂;EIS在高频区呈容抗弧,在低频区呈感抗弧,添加PSLE后,阻抗值显著增大.SEM表明添加PSLE对铝的腐蚀产生了明显的抑制作用.量子化学计算结果表明,牡荆苷和异牡荆苷的吸附中心主要集中在竹叶黄酮骨架(FBS).     

嘧啶衍生物对钢在盐酸溶液中的缓蚀作用

采用失重法、动电位极化曲线、电化学阻抗谱(EIS)、量子化学计算研究了两种嘧啶衍生物(2-羟基嘧啶(HP)和2-巯基嘧啶(MP))在1.0-5.0 mol·L^-1 HCl溶液中对冷轧钢(CRS)的缓蚀作用. 结果表明: HP和MP在1.0 mol·L^-1 HCl溶液中对冷轧钢具有良好的缓蚀作用, 且在钢表面的吸附符合Langmuir吸附等温式. 缓蚀率随缓蚀剂浓度的增加而增大, 但随盐酸浓度的增加而减小.求出了相应的吸附热力学参数(吸附平衡常数(K),吸附自由能(ΔG⁰))和腐蚀动力学参数(表观活化能(E_a)、指前因子(A)、腐蚀速率常数(k)、动力学常数(B)), 并根据这些参数讨论了缓蚀作用机理. 动电位极化曲线表明, MP和HP均为混合抑制型缓蚀剂; EIS谱呈单一容抗弧,电荷转移电阻随缓蚀剂浓度的增加而增大. 两种嘧啶化合物的缓蚀率排序为MP>HP. 量子化学计算结果表明,MP比HP更具吸附活性,缓蚀性能的理论计算和实验结果相一致.