涂石蜡大米傅立叶变换红外吸收光谱识别分析

针对11种未涂石蜡大米和18个涂不同量石蜡的大米样品,以石油醚提取的油脂为试样,采用傅立叶变换红外光谱仪,扫描样品的傅立叶变换红外吸收光谱,并对光谱进行预处理,提取红外特征信息,将2855与1746、1462与1163 cm-1处特征峰的面积比值为坐标,采用Origín 6.0软件作识别分类图.结果表明:特征峰的面积比值与所涂石蜡量成线性变化,大米油脂的特征峰面积比值在一定的区域分布,涂以0.05%以上石蜡的大米,其油脂特征峰面积比值与未涂石蜡米油脂的值有一定区别.     

TGA/FT-IR: Thermogravimetric analysis with fourier transform infrared detection of evolved gases

Thermogravimetric analysis (TGA) is a widely employed technique for measuring the change in weight of a sample as a function of temperature or time in a controlled atmosphere. FT-IR has been utilized with success in the identification of gases [1]. The combination of these two techniques permits a complete characterization of materials in terms of thermal stability and decomposition mechanisms [2]. A complete integrated system for TGA/FT-IR analysis is described.     

板蓝根颗粒中蔗糖含量的红外光谱法测定

A method for rapid quantitative determination of sucrose in isatis-root granules by Fourier Transform Infrared Spectrophotometry(FTIR) was developed. Potassium ferricyanide was chosen as an inside mark material because it has only one strong absorption peak at 2117cm-1 and the peak was chosen as its quantitative peak. The peak at 1283cm-1 is the characteristic absorption of sucrose and was chosen as the quantitative peak of sucrose. The ratio of the two absorbances is I=Ai/As.K3[Fe(CN)6] and sucrose were mixed according to a certain mass ratio m=mi/ms to prepare standard samples. The curve of m versus I is the quantitative working curve. The linear range for sucrose is 5.0～23.0mg/g,the recovery is in the range of 91%～103%,the relative standard deviation is less than 5%.     

Fourier transform raman spectroscopy using a bench-top fourier transform infrared spectrometer

The use of a bench top FTIR spectrometer for near infrared Fourier transform Raman spectroscopy is demonstrated. The use of near infrared excitation results in fluorescence free Raman spectra allowing previously difficult samples to be measured.     

Comparative analysis of smokeless gunpowders by Fourier transform infrared and Raman spectroscopy

Fourier Transform Infrared (FTIR) and Raman spectroscopic techniques were used to perform a comparative study of the spectral profiles of single-base, double-base and triple-base smokeless gunpowders. Preliminary results based on visual comparison of the spectra point out that spectra obtained by both vibrational techniques were useful for a rapid identification of gunpowders containing dinitrotoluene as one of the major components and triple-base gunpowders. Additionally, the Raman spectra of gunpowders with diphenylamine in its primary composition showed a characteristic band, assigned to 2-nitro-diphenylamine, allowing the identification of this type of gunpowders.     

Diffusion measurements with fourier transform infrared attenuated total reflectance spectroscopy: Water diffusion in polypropylene*

The diffusion of pure liquid water into a commercial polypropylene (PP) film at 278–348 K was studied with Fourier transform infrared attenuated total reflectance spectroscopy. Abnormal diffusion behavior was indicated by a significant deviation between the experimental data and a Fickian diffusion model with the conventional saturated boundary condition applied at the water/PP interface. This deviation was observed at all the temperatures studied. With a modified boundary condition that took into account a mass‐transfer resistance at the water/PP interface, the Fickian model was able to represent the experimental data satisfactorily. The average water diffusion coefficient varied between 1.41 and 7.64 × 10^?9 cm²/s, with an activation energy of diffusion of about 19.3 kJ/mol. The interfacial mass‐transfer resistance was represented by an exponential model with an empirical relaxation parameter. The relaxation parameter β increased as the temperature increased and reached an apparent plateau. The infrared spectrum indicated a positive chemical shift of 18 cm^?1 for the less strongly hydrogen‐bonded component of the broad hydroxyl stretching band with respect to pure liquid water, indicating that hydrogen‐bonding interactions were weakened or broken when water molecules diffused into the PP matrix. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 980–991, 2002     

Determination of trace amounts of chromium (VI) by flow injection analysis with chemiluminescence detection

A new sensitive chemiluminescence (CL) method combined with continuous flow injection analysis is described for the determination of Cr(VI). Strong CL signals were generated by Cr(VI)-catalysed oxidation of gallic acid in the presence of potassium permanganate and hydrogen peroxide. Effects of reagent concentrations, temperature, pH, flow rates, mixing coil length and mixing flow sequences on the chemiluminescence intensity were studied. Under the optimised experimental conditions, the relationship between the logarithm of concentration (log?C) of Cr(VI) and the logarithm of intensity (log?I) is linear over the range of 2?×?10^?11 – 5?×?10^?4?mol?L^?1, with the detection limit (3σ) of 4?×?10^?12?mol?L^?1. Relative standard deviation of ten measurements of 1?×?10^?9?mol?L^?1 Cr(VI) is 1.7%. This flow injection analysis (FIA) system proved to be able to analyse up to 40 samples h^?1. Effects of various interferences possibly present in the water samples were investigated. Most cations and anions, as well as organic compounds, did not interfere with the determination of Cr(VI) in water samples. The experimental results obtained for chromium in reference materials were also in good agreement with the certified values.     

Electrospray micro liquid chromatography – Fourier transform infrared micro spectrometry

Microcolumn liquid chromatography has been interfaced with infrared microspectrometry by means of a novel technique involving electrospray nebulization. The eluent from the LC column is subjected to a high positive potential relative to the surroundings and the electric field generated charges the surface of the emerging liquid causing it to disintegrate into charged droplets which are attracted to an earthed, infrared-transparent, zinc selenide deposition plate. Nitrogen sheath gas is used to evaporate the solvent in the droplets, and the separated components are deposited on the zinc selenide plate for subsequent analysis by means of a Fourier transform infrared microscope and spectrometer. Provided low flow rates (～4 μl/min) are used, total elimination of the solvent is achieved and easily identifiable infrared spectra can be measured from less than 500 pg of sample (caffeine).     

Determination of caffeine in black tea leaves by Fourier transform infrared spectrometry using multiple linear regression

A simple and fast analytical procedure was developed for the determination of caffeine in black tea leaves. The method is based on multiple linear regression treatment of Fourier transform infrared spectrometric data obtained in the wave number range 1800–1300 cm⁻¹ after extraction of caffeine in CHCl₃ from tea samples, wetted with an aqueous solution of NH₃ (0.1 M). The procedure requires no complex sample preparation. It provided a limit of detection of 0.035 mg/ml, a sampling frequency of 6 h⁻¹ and a coefficient of variation of 0.8% for five independent measurements of a tea sample with 3.68% w/w caffeine content. This procedure provides a drastic reduction in the consuming organic solvent for each sample compare to that of the reference chromatographic determination. The accuracy of technique is evaluated by comparing the obtained results with those of a reference HPLC technique. An average value of 3.60±0.07% w/w was obtained by HPLC for a powdered tea sample which is compromising when is compared to 3.68±0.03% (w/w) obtained by this FTIR technique.     

Micellar electrokinetic chromatography with on-line Fourier transform infrared detection

Micellar electrokinetic chromatography (MEKC) was successfully coupled to Fourier transform infrared (FTIR) detection, using a micromachined IR-transparent flow cell with an optical path length of 15 micro m for the on-line detection of five neutral analytes. Tight connections between the flow cell and the capillaries were achieved by creating a small O-ring of UV-curing epoxy adhesive on the sharply cut capillary ends. The background electrolyte consisted of 15 mM phosphate buffer at pH 7 and 40 mM sodium dodecyl sulfate (SDS). Five analytes (paracetamol, caffeine, p-nitro benzyl alcohol, m-nitrophenol and p-nitrophenol) were successfully separated, yielding detailed IR stack plots that could be used for quantification and identification. Linear calibration graphs were obtained for each individual analyte present in mixtures at concentrations up to 10 mM. The limit of detection (3 S/N) ranged between 1.1 and 1.5 mM (1.2-1.8 ng). Analytes were identified by comparing spectra obtained during the MEKC separation with those resulting from completely filling the capillary with each individual analyte dissolved in the micelle-containing electrolyte. Information on the specific functional groups of all analytes could be elucidated from the spectra. Since FTIR is a nondestructive detection technique, a conventional on-line UV detector was introduced directly after the developed IR flow cell to test the system's performance and to demonstrate that tandem FTIR and UV detection is feasible.     

Multicomponent analysis with a computerized flow injection system using LED photometric detection

An original computer-controlled solid-state photometer has been developed and its potential for simultaneous multicomponent flow-injection analysis of binary and ternary mixtures is demonstrated. The device is simple in construction. Its principle of operation is based on rapid sequential measurements of the absorbance of the complexes formed by the analytes with chromogenic reagents at the wavelengths corresponding to the emission maxima of three light emitting diodes (563, 580 and 638 nm).     

An in situ Fourier transform infrared spectroscopy method for collecting real-time data for the liquid-phase reaction of CO2 and mono-ethanolamine in alcoholic solvent systems

A novel Fourier transform infrared (FTIR) spectroscopy method of analysis was developed to study the industrially important reaction of CO₂ with the primary amine, mono-ethanolamine (MEA), in n-propanol as representative alcoholic solvent. A semi-batch reactor with a piston like ‘floating’ head was specifically designed in order to study the reaction in the liquid phase, thereby eliminating the mass transfer limitations of a gas-liquid system. An attenuated total reflectance (ATR) probe was used to monitor the change in reagent and product concentrations in-situ. Successful spectral peak identification and calibrations were performed in order to collect real time, reaction kinetic data. Data analysis confirmed that the zwitterion reaction mechanism most accurately describes the reaction in non-aqueous systems.     

红外光谱法测定壳聚糖含量(英文)

采用吡喃环上的次甲基的吸收峰(1 389和2 865cm-1)面积比作为定量参照,建立了一种检测壳聚糖含量的傅立叶变换红外光谱(FT-IR)分析方法,并验证了其适用性.结果表明,所建立的FT-IR分析方法可用于定量测定药物剂型中的壳聚糖含量.     

Column switching applied to capillary gas chromatography/fourier transform infrared spectroscopy

A dual oven gas chromatograph incorporating a micro, mechanical switching valve has been interfaced to an FTIR spectrometer. With this system, each oven can be operated with independent temperature control. Complete choice of the columns' type and capacity gives flexibility in the separation prior to spectroscopic evaluation. An application which demonstrates some of the advantages of column switching in GC/FTIR is presented. Minor sample components have been successfully analyzed by heart-cutting the appropriate section of the separation from a high to a low capacity column. In this way, the dynamic range of the technique is effectively increased while an efficient chromatographic inlet to the FTIR is maintained.     

Determination of total sterols in brown algae by Fourier transform infrared spectroscopy

A procedure is proposed for the determination of the total amount of sterols in brown algae Bifurcaria bifurcata, Cladostephus hirsitus, Dictyota dichotoma and Cystoseira sedoides, globally determined as fucosterol, which is the major sterol contained in these algae. The method involves the use of cholesterol as reference standard and a correction factor of 1.259 ± 0.003, which represents the ratio between the slopes of calibration lines obtained from fucosterol and cholesterol. The method provides precise and accurate results for the IR analysis of real samples.     

Simultaneous determination of Folpet and Metalaxyl in pesticide formulations by flow injection Fourier transform infrared spectrometry

Fourier transform infrared (FTIR) spectrometric methodology has been developed for the simultaneous determination of Folpet and Metalaxyl in pesticide formulations. The method involves the extraction of both active principles by sonication of the sample with CHCl₃ and direct measurement of the absorbance using peak height values at 1798 cm⁻¹ corrected with a baseline defined at 1810 cm⁻¹ for Folpet, and peak area data established from 1677 to 1667 cm⁻¹ corrected using a baseline from 1692 to 1628 cm⁻¹ for Metalaxyl. Limits of detection (3 s) values of 17 and 16 μg g⁻¹ were found for Folpet and Metalaxyl, respectively, with results comparable with those found by liquid chromatography with UV detection. The new method involves a considerable decrease in solvent consumption. The automation of the procedure by incorporating on-line dissolution and filtration of the samples allows complete mechanisation of the method and improves the safety of operation.     

Attenuated total reflectance/fourier transform infrared studies on the phase‐separation process of aqueous solutions of poly(n‐isopropylacrylamide)

Temperature‐induced phase separation of poly(N‐isopropylacrylamide) in aqueous solutions was studied by attenuated total reflectance (ATR)/Fourier transform infrared spectroscopy. The main objectives of the study were to understand, on a molecular level, the role of hydrogen bonding and hydrophobic effects below and above the phase‐separation temperature and to derive the scenario leading to this process. Understanding the behavior of this particular system could be quite relevant to many biological phenomena, such as protein denaturation. The temperature‐induced phase transition was easily detected by the ATR method. A sharp increase in the peaks of both hydrophobic and hydrophilic groups of the polymer and a decrease in the water‐related signals could be explained in terms of the formation of a polymer‐enriched film near the ATR crystal. Deconvolution of the amide I and amide II peaks and the O? H stretch envelope of water revealed that the phase‐separation scenario could be divided, below the phase‐separation temperature, into two steps. The first step consisted of the breaking of intermolecular hydrogen bonds between the amide groups of the polymer and the solvent and the formation of free amide groups, and the second step consisted of an increase in intramolecular hydrogen bonding, which induced a coil–globule transition. No changes in the hydrophobic signals below the separation temperature could be observed, suggesting that hydrophobic interactions played a dominant role during the aggregation of the collapsed chains but not before. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1665–1677, 2001     

Bleachability and characterization by fourier transform infrared principal component analysis of acetosolv pulps obtained from sugarcane bagasse

Sugarcane bagasse Acetosolv pulps were bleached by xylanase and the pulps classified by using Fourier transform infrared (FTIR) spectroscopy and principal component analysis (PCA). Pulp was treated with xylanase for 4–8 h with stirring at 30°C. Some samples were further extracted with NaOH for 1 h at 65°C. FTIR spectra were recorded directly from the dried pulp samples by using the diffuse reflectance technique. Reduction in kappa number of 69% was obtained after sequence xylanase (4 h)-alkaline extraction. During bleaching the viscosity decreased only 12%. FTIR-PCA showed that the first three principal components (PCs) explained more than 90% of the total variance of the pulp spectra. PC2×PC1 plot showed that the points related to pulps from sequence xylanase (4 h)-alkaline extraction are different from the other. This group isenlarged by plotting PC3×PC1 or PC3×PC2 containing all pulps submitted to alkaline extraction. PC2 and PC3 are the principal factor for differentiation of the pulps. These PCs suffer influence of the ester bands (1740 and 1244 cm⁻¹). On the other hand, the pulps bleached only with xylanase could not be differentiated from the nonbleached pulps.