1,2-聚丁二烯分子运动的~(13)C-NMR研究——Ⅱ.分子运动的温度依赖性

本文用200MHz脉冲傅利叶变换波谱仪测定了1,2-聚丁二烯样品在不同温度下的~(13)C-T_(19)NOE,线宽和化学位移等~(13)G自旋弛豫参数,研究了1,2-聚丁二烯分子运动的温度依赖性.结果发现,在-10—-30℃之间,样品中各碳核的NOE和谱线宽度随温度变化的曲线斜率增加,表明此时长程链运动冻结;各碳核nT_1随温度的变化均在-45℃左右出现极小值.     

用模型拟合法研究1,2-聚丁二烯分子运动

本文采用Cole-Cole,Fuoss-Kirkwood经验相关时间分布模型和构象跳跃,高聚物局部主链运动阻尼取向扩散分子模型,对1,2-聚丁二烯在溶液中的~(13)C-NMR自旋-晶格弛豫时间nT_1和核Overhauser效应(NOE)值进行了数值拟合。用拟合所得分子运动参数讨论了1,2-聚丁二烯微观分子运动对链结构和温度的依赖性。     

W-Al体系在合成1,2-聚丁二烯中的催化活性

WCl_6是优良的开环聚合催化剂,但只有一篇专利中提到用WCl_6催化丁二烯的聚合得到非顺式1,4-聚丁二烯,而且活性很低.用钨化合物催化丁二烯聚合为高1,2-链节含量的聚丁二烯,则尚未有报道.我们的工作发现,WCl_4(OR)_2-(i-Bu)_2AlOPh体系可使丁二烯在加氢汽油中聚合成1,2-链节含量在80％左右,1,2-链节的全同立构体含量达60％以上的聚丁二烯.为合成1,2-聚丁二烯橡胶开辟了一个新的催化体系.但是,初步研究结果表明:催化活性和聚合物分子量均较低.因此,本文试图探索提高催化活性和聚合物分子量的方法.     

~(13)C-NMR研究聚丁二烯的序列结构

本文采用~13C-NMR方法研究了不同催化体系制备的聚丁二烯。经分析指出,聚丁二烯分子链的三种序列(顺-1,4-序列、反-1,4-序列和1,2-序列)和十七类脂碳碳核为~13C-NNR谱贡献了十六个谱峰。经数据的解析,得到一组计算聚丁二烯脂碳部分各谱峰化学位移的经验参数。在本文条件下,应用该组参数得到的计算值与实验值符合较好。本文确认了聚丁二烯反-1,4-序列第四峰(T_4)的存在。初步研究了聚丁二烯~13℃-NMR谱图的定量处理问题。     

含反式-1,4和间规-1,2链节的聚丁二烯X-射线衍射谱分析

<正> 近年来陆续出现在顺式-1,4聚丁二烯分子链中引入室温下可结晶的反式-1,4及间规-1,2聚丁二烯链节,以期改善顺丁橡胶的抗撕裂性和抗弯曲性等。有关这方面的结构表征工作尚很少报道。本工作用广角X-射线衍射(WAXD)方法,对钒、钴催化体系合成的含反式-1,4及钴催化体系合成的含间规-1,2的顺丁橡胶进行了结构表征。     

~(13)C-NMR化学位移与聚合物的构象——Ⅰ.1,2-聚丁二烯乙烯基叔碳(-CH=)的~(13)C-NMR谱研究

本文应用半经验方法来解析无规1,2-聚丁二烯乙烯基叔碳(—CH=)的~(13)C-NMR谱图。研究指出只有主链CH与乙烯基叔碳之间的gauche排列和由此产生的屏蔽效应对后者的化学位移的改变作出了贡献。因此,可以直接利用键概率来归属十个五元组立构异构体的排列顺序。由于上述原因,得到了对于无规1,2-聚丁二烯乙烯基叔碳的~(13)C-NMR谱的一种新的归属,并且通过研究全同和间同1,2-聚丁二烯的~(13)C-NMR谱图予以证明。     

测定聚丁二烯微结构的拉曼光谱方法

本文采用聚丁二烯中碳碳双键伸缩振动的拉曼散射峰1667、1652和1639cm~(-1)分别作为反1,4、顺1,4和1,2结构的分析峰,借助于1H-NMR测得的典型样品的1,2结构含量,建立了测定聚丁二烯微结构的拉曼光谱方法。用本方法测定了27个微结构组成大范围变化的样品,与1H-NMR的测定结果相符。     

1,2-聚丁二烯~(13)C-NMR弛豫的溶剂效应

本文测定了一系列具有不同微观结构的1,2-聚丁二烯样品在四种溶剂的50.3MHz ~(13)C自旋-晶格弛豫时间(T_1)和核Overhauser效应(NOE)值。并用Schaefer logx~2相关时间分布模型对实验数据进行了拟合。研究了1,2-聚丁二烯在溶液中的~(13)C-NMR弛豫的溶剂效应及其与结构的关系。发现聚合物与溶剂的溶解度参数之差△δ越大,聚合物在溶液中协同链段运动趋向越明显,~(13)C自旋-晶格弛豫速率(1/T_1)越大;1,2-链节较少,分子链较柔顺时,~(13)C-NMR弛豫受溶剂影响较显著。NMR弛豫参数对结构变化的反应在良溶剂中比在不良溶剂中敏感。     

聚丁二烯~(13)C-NMR谱图中一个新的共振吸收峰(T_4)

<正> 最近解析锂系和铁系含乙烯基聚丁二烯的~(13)C-NMR谱图,发现并确认了一个新的共振吸收峰。即聚丁二烯反式1,4-序列的第四峰,简称T_4峰。 Furukawa等对钼系和章哲彦等对铁系等二元聚顺-1,4-1,2-丁二烯的研究都指出在聚丁二烯的~(13)C-NMR谱图上,有四个谱峰属于顺1,4-序列。本文给出其化学位     

聚丁二烯的序列结构

Ⅰ.¹³C-NMR研究聚丁二烯的序列结构 聚丁二烯的链状分子包含三种序列,十七类脂碳碳核。其中包含被遗漏的反1,4-序列的第四碳。在聚丁二烯的¹³C-NMR谱图上确认了与之对应的共振吸收峰,T₄峰。得到了一组经验参数,当用于聚丁二烯的¹³C-NMR谱图(脂碳部分)时,各谱峰化学位移计算值和实验值相一致。但是,与1,2-序列两端的四类碳核:Ca₄, T₄, V₂和V₈相对应之谱峰的化学位移计算值均低于实验值。     

CARBON-13 NMR STUDY OF MOLECULAR MOTION OF 1, 2-POLYBUTADIENES IN SOLUTION Ⅰ. STRUCTURE DEPENDENCE OF MOLECULAR MOTIOM

Proton decoupled, partially relaxed, Fourier-transform 50.3 MHz carbon-13 NMR in naturalabundance was used to determine spin-lattice times (T_1) and nuclear Overhauser enhancement fac-tors (NOE) of individual carbon of a serics of 1,2-polybutadienes with different structures in solutionin CDCl_2 The structure dependence of molecular metion and the internal motion of vinyl group in1,2-polybutadiene have been studied by nT_1 and NOE values. The nT_1 values of the carbons in cis-1,4-units are the highest and those of the carbons in 1.2-units are the lowest in three types of units in1,2-polybutadiene. The nT_1 values of carbons in the same unit become greater when the adjacent1,2-units are replaced by 1,4-units, and nT_1 values of the carbons in all units decrease sharply withthe increase of content of 1,2-units in the polymers. The fact that nT_1 values of --CH=are larger than those of=CH_2 in vinyl group impliesthat there are complex internal motions of vinyl group. It is shown by calculation that the dominantfactor causing the difference in nT_1 of--CH=and=CH_2 in vinyl group is a swing of vinyl group ina plane peopndicular to the chain backbone.     

用Co(naph)2-Al2(C2H5)3Cl3-P(OPh)3催化体系合成中乙烯基液体聚丁二烯

为获得适中乙烯基含量的液体聚丁二烯为目的, 对Co(naph)2-Al2(C2H5)3Cl3-P(OPh)3催化体系进行了较为系统的研究, 考察了该体系的催化剂配比、浓度及供电子试剂对分子量、微观结构和转化率的影响. 实验结果表明, 该体系在一定的条件下可以制备出分子量在700~3500、1,2结构含量在35%~40%且转化率高于55%的液体聚丁二烯.     

Filler-polymer interactions in filled polybutadiene compounds

Bound rubber in a filled rubber compound is formed by physical adsorption and chemisorption between the rubber and filler. Polybutadiene (PB) is composed of three components of 1,2-, cis-1,4-, and trans-1,4-units. Filler-polymer interactions in PB compounds filled with carbon black or silica were studied by analyzing microstructures of the bound rubbers with pyrolysis-gas chromatography. Differences in the filler-polymer interactions of the 1,2-, cis-1,4-, and trans-1,4-units were investigated. The filler-polymer interaction of the 1,2-unit is stronger than those of the cis-1,4- and trans-1,4-units. The interaction of the 1,2-unit with silica is stronger than with carbon black. Bound rubber content is decreased by treatment with ammonia. Change of the bound rubber composition after the ammonia treatment was also studied.     

辐射交联顺1,4-聚丁二烯的NMR研究

用１３Ｃ ＮＭＲ方法,测定了辐射交联顺１,４ 聚丁二烯在室温下的自旋 晶格弛豫时间（Ｔ１）,核Ｏｖｅｒｈａｕｓｅｒ因子（ＮＯＥ）,和１３Ｃ ＮＭＲ线宽．以及凝胶本体１Ｈ ＮＭＲ的Ｔ１和Ｔ２弛豫时间,结果表明,辐射交联顺１,４ 聚丁二烯体系中,随着凝胶含量的增加各碳核质子的Ｔ１值变化很小,而—ＣＨ２—核的ＮＯＥ因子明显降低和１３Ｃ ＮＭＲ线宽增宽．以及１Ｈ ＮＭＲ的Ｔ１和Ｔ２表现的双指数弛豫特性反映了交联体系中大分子链段长程运动受阻以及饱和交联叔碳核—ＣＨ对链段运动的影响．     

Novel analytical method for determination of contents of backbone and terminal/branch vinyl acetate groups of poly(ethylene-co-vinyl acetate) using deacetylation reaction

Vinyl acetate (VA) groups in poly(ethylene-co-vinyl acetate) (EVA) exist in backbone, terminal, and branch positions. The VA moieties were converted to carbon-carbon double bonds (∼CH=CH∼) by deacetylation reaction. By deacetylation, the backbone VA group was converted to 1,4-unit (∼CH₂CH=CHCH₂∼) while the terminal and branch ones were converted to 1,2-unit (∼CH=CH₂). A novel analytical method for determination of ratio of backbone and terminal/branch VA contents was developed using off-line pyrolysis and transmission-Fourier transform infrared spectroscopy (FTIR). The analytical method included sample preparation of deacetylated EVA coated on NaCl window for transmission-FTIR analysis and calculation of backbone and terminal/branch VA contents using quantitative analysis of 1,4- and 1,2-units of the deacetylated EVA. Influence of deacetylation conditions (pyrolysis temperatures and times) on degree of deacetylation and other side reactions was also investigated, and proper deacetylation condition was suggested. From the experimental results, proper off-line pyrolysis condition of EVA coated on NaCl window was 300 °C for 60–80 min. The novel analytical method was reliable with the experimental error of below 5%.     

双烯类聚合物的热分析——I.间规1,2-聚丁二烯的熔融-结晶与热氧化

由钴催化体系合成的间规1,2-聚丁二烯是结晶性的,熔点205—210℃,与1,2-链节含量无关。低1,2-含量(12—20mol％)时,热氧化峰温为185℃左右,高1,2-含量(95—100mol％)时,200到240℃。换言之,与主链双键相比,侧链乙烯基的热氧化反应发生在更高的温度,即在熔融后的较窄的温度范围表现出较大的热效应。高1,2-含量间规聚丁二烯热氧化的热效应和活化能值,似与合成转化率有一定联系,当达到一定转化率时,热效应急剧增高,而活化能降低,估计这与残留在试样中催化剂的量及存在形式有关。     

红外光谱法研究镍顺丁橡胶分级样品及凝胶的微结构

顺丁橡胶的链结构与其溶液性质和物理性能有密切关系,凝胶的存在往往影响加工和使用性能。付里叶变换红外光谱技术的发展使我们有可能考察顺丁分子链微结构与分子量的关系,研究凝胶与线性分子链结构的差别。     

1,2-聚丁二烯分子链的结构和内旋转运动

实验订定了1,2-链节含量分别为8％,30％和90％的1,2-聚丁二烯在30℃甲苯溶液中的Mark-Houwink方程[η]=KM~(?)。发现不同样品的α值基本相同,而K值确实随1,2-链节含量的增加而减小,说明溶液中分子链线团变得紧密了。用线膨胀法和Stockmayer-Fixman方程及分子链的统计力学方法,分别得到了样品的玻璃化温度T_g,和它们的分子链内旋转空间位阻因子σ。它们二者符合T_g=A(σ—b),其中A=174(K),b=0.68。反映了1,2-链节对分子链内旋转的阻碍作用。进一步的研究表明,低1,2-链节含量对应着较低的分子链内旋转势垒和内旋转异构化能。     

Considering factors on determination of microstructures of SBR vulcanizates using pyrolytic analysis

Properties of styrene-butadiene rubbers (SBRs) are depending on their microstructures (contents of 1,4-unit, 1,2-unit, and styrene), but it is hard to determine the microstructures of SBR vulcanizates. Pyrolytic method such as pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) has been used for microstructures of cured rubbers without pretreatment. Microstructure of SBRs can be estimated using the major pyrolysis products (butadiene, 4-vinylcyclohexene (VCH), and styrene). In this study, considering factors for determination of microstructures of SBR vulcanizates using Py-GC/MS were investigated. The principal considering factors were found to be change of the major pyrolysis products due to radicals formed in carbon backbone and sulfur by dissociation of sulfide crosslinks in SBR vulcanizates. Relative abundances of the major pyrolysis products of raw and cured SBRs were different due to rearrangements of the radicals. Influencing factors on pyrolysis behaviors of SBR vulcanizates were found to be 1,2-unit block, alternating sequence of 1,4- and 1,2-units, styrene-1,4-unit and styrene-1,2-unit sequences, and location of the radicals. Especially, the 1,2-unit block influenced on change of the VCH/butadiene ratio, while the styrene-1,2-unit sequence affected change of the styrene/(butadiene + VCH) one.