Alkanethiol monolayers at reduced and oxidized zinc surfaces with corrosion protection: a sum frequency generation and electrochemistry investigation

In this work, octadecanethiol (ODT) was demonstrated to form ordered monolayers at either electrochemically reduced or oxidized Zn surfaces, by means of sum frequency generation (SFG) spectroscopy, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The SFG spectra of ODT-modified Zn electrodes featured three methyl group resonances in the C-H vibrational region (2800-3100 cm(-1)). A significant decrease in interfacial capacitance and an increase in charge-transfer resistance were observed in EIS measurement after ODT modification. The alkane chain tilt angle of ODT within a monolayer at the Zn surface was estimated as 0 degrees with respect to the surface normal by interfacial capacitance measurement via EIS. CV and SFG investigation revealed that ODT monolayers undergo reductive desorption from the Zn electrode in 0.5 M NaOH at -1.66 V (vs SCE) and in 0.5 M NaClO4 at -1.62 V. The integrated charge consumed to the desorption of ODT is determined as 87 mC/cm2 from the reductive peak on CV curve, resulting in a coverage of 9.0 x 10(-10) mol/cm2 (5.4 x 10(14) molecules/cm2) if assuming the reduction follows a one-electron process. ODT monolayers show corrosion protection to underlying zinc at the early immersion stage in base, salt, and acid media. However, the protection efficiency was reduced with immersion time due to the presence of defects within the monolayers.     

Single-component and mixed ferrocene-terminated alkyl monolayers covalently bound to Si(111) surfaces

Self-assembled ferrocene monolayers covalently bound to monocrystalline Si(111) surfaces have been prepared from the attachment of an amine-substituted ferrocene derivative to a pre-assembled acid-terminated alkyl monolayer using carbodiimide coupling. This derivatization strategy yielded nanometer-scale clean, densely packed monolayers, with the ferrocene units being more than 20 A from the semiconductor surface. The amount of immobilized electroactive units could be varied in the range 2 x 10(-11) to approximately 3.5 x 10(-10) mol cm(-2) by diluting the ferrocene-terminated chains by inert n-decyl chains. The highest coverage obtained for the single-component monolayer corresponded to 0.25-0.27 bound ferrocene per surface silicon atom. The electrochemical characteristics of the mixed n-decyl/ferrocene-terminated monolayers were found to not depend significantly on the surface coverage of ferrocene units. The reversible one-electron wave of the ferrocene/ferrocenium couple was observed at E degrees ' = 0.50 +/- 0.01 V vs SCE, and the rate constant of electron transfer kapp was about 50 s(-1).     

A novel ferroceneylazobenzene self-assembled monolayer on an ITO electrode: photochemical and electrochemical behaviors

A novel ferroceneylazobenzene self-assembled monolayer (SAM) has been constructed on an indium-tin oxide (ITO) electrode via the covalent attachment of 4-(4'-11-ferrocenyl-undecanoxyphenylazo)benzoic acid ( FcAzCOOH) onto a silanized ITO substrate surface and verified by reflectance infrared spectroscopy and water contact angle. Atomic force microscopy (AFM) and cyclic voltammogram (CV) indicated that the FcAzCOOH formed a uniform and reproducible SAM on the ITO electrode with a surface coverage of ca. 1.9 x 10 (-10) mol/cm (2) (87 A (2)/molecule). The reversible photoisomerization behavior of the SAM was characterized by UV-vis spectra. The azo pi-pi* transition band intensity of the SAM gradually decreased with UV (365 nm) irradiation and was almost recovered again when subsequent exposure to ambient room light (400-800 nm). The increased tilt angle of the molecules on the ITO substrate after UV irradiation further confirmed the trans-to- cis isomerization of azobenzene moieties. The CV of the trans- FcAzCOOH modified ITO electrode showed a pair of waves due to redox of the ferrocene groups in the potential range of 0 to +800 mV (vs SCE), and the peak separation of the redox wave became larger after UV irradiation and almost returned to its original value after subsequent exposure to the visible light. Rate-dependent CV curves indicated that the charge transfer rate between the ferrocene species in the SAM and the ITO electrode was slowed down after UV irradiation due to the smaller porosity of the monolayer film and the more compact barrier layer between the redox species and the ITO electrode. It is the first time to directly observe the influence of photoisomerization of the azobenzene moiety on the redox behavior of redox species in the ferroceneylazobenzene-functionalized SAM. The present results provide profound insight into the role of redox microenvironment on electron transfer kinetics and also provide a simple and facile approach to the preparation of photocontrollable electrodes.     

Studies on the effect of electrode pretreatment on the coverage of self-assembled monolayers of dodecanethiol on gold by electrochemical reductive desorption determination

This paper examines the effect of five major pretreatments on the surface coverage Γ(m) of dodecanethiol self-assembled monolayer on polycrystalline gold electrode (C(12)SH-SAMs-Au). It is based on the electrochemical reductive desorption in the alkaline solution by cyclic voltammetry (CV). The five different pretreatment methods include: aqua regia pretreatment, reductive annealed pretreatment, UV/O(3) pretreatment, piranha reagents pretreatment and simple polishing pretreatment, and then all above pretreatments following the same procedure of electrochemistry cleaning. The experimental results show that the surface coverage Γ(m) for C(12)SH-SAMs-Au by the five pretreatment methods are: aqua regia pretreatment (8.0 × 10(-10) mol cm(-2)) ~ reductive annealed pretreatment (7.8 × 10(-10) mol cm(-2)) > UV/O(3) pretreatment (5.0 × 10(-10) mol cm(-2)) ~ piranha reagents pretreatment (4.1 × 10(-10) mol cm(-2)) ~ simple polishing pretreatment (4.0 × 10(-10) mol cm(-2)). This indicates that Au surfaces pretreated by aqua regia and reductive annealing can achieve the best results, and the Γ(m) values obtained are consistent with the theoretical coverage values (Γ(m) ≈ 8.0 × 10(-10) mol cm(-2)); however, the Γ(m) values for other three pretreatment methods (UV/O(3), piranha reagents and simple polishing) are not satisfactory, obtaining only almost half of the theoretical Γ(m) value. Thus, we recommend aqua regia and reductive annealed pretreatments as the best methods for self-assembling the alkyl thiol monolayer (C(n)SH-SAMs-Au), whereas UV/O(3), piranha reagents and simple polishing pretreatments are not recommended.     

A compact all-carbon tripodal tether affords high coverage of porphyrins on silicon surfaces

[Structure: See text] Redox-active molecules designed to give high charge density on electroactive surfaces are essential for applications in molecular information storage. To achieve a small molecular footprint and thereby high surface charge density, a compound consisting of a triallyl tripod attached via a p-phenylene unit to a porphyrin (1) has been synthesized. The zinc chelate of 1 (Zn-1) was attached to Si(100). Electrochemical measurements indicate that the molecular footprint (75 A) in the monolayer is only approximately 50% larger than the minimum achievable, indicating high surface coverage. IR spectroscopy indicates that the bands due to the nu(C=C) (1638 cm(-1)) and gamma(CH) (915 cm(-1)) vibrations present in the solid sample (KBr pellet) are absent from the spectra of the monolayers of Zn-1, consistent with saturation of the double bond in each of the three legs of the tripod upon the hydrosilylation process accompanying attachment. Comparison of the relative intensities of the in-plane (998 cm(-1)) versus out-of-plane (797 cm(-1)) porphyrin modes indicates the average tilt angle (alpha) of the porphyrin ring with respect to the surface normal is approximately 46 degrees , a value also observed for analogous porphyrins tethered to Si(100) via monopodal carbon linkers. Accordingly, the higher packing densities afforded by the compact tripodal linker are not due to a more upright orientation on the surface. The charge-retention half-lives (t1/2) for the first oxidation state of the Zn-1 monolayers increase from 10 to 50 s at low surface coverage (1-5 x 10(-11) mol.cm(-2)) to near 200 s at saturation coverage (approximately 2 x 10(-10) mol.cm(-2)). Taken together, the high surface charge density (despite the lack of upright orientation) of the triallyl-tripodal porphyrin makes this construct a viable candidate for molecular information storage applications.     

Interfacial supramolecular self-assembled monolayers of C(60) by thiolated beta-cyclodextrin on gold surfaces via monoanionic C(60)

The supramolecular self-assembled monolayers (SAMs) of C(60) by thiolated beta-cyclodextrin (CD) on gold surfaces were constructed for the first time using C(60) monoanion. The results indicate that monoanionic C(60) plays a crucial role in the formation of the C(60)-containing self-assembled monolayers. The generation of C(60) monoanion and the formation process of C(60) SAMs were monitored in-situ by UV-visible and near-IR spectroscopy. The resulting C(60) SAMs were fully characterized by spectroscopic ellipsometry (SE), cyclic voltammetry, X-ray photoelectron spectroscopy (XPS), and water contact angle measurements. After the immobilization of C(60) by the SAMs of thiolated beta-CD, the film thickness increased by approximately 1 nm from 0.8 to 1.8 nm as determined by SE, demonstrating the formation of the supramolecular self-assembled monolayers of thiolated beta-CD/C(60). The new C(60) SAMs exhibited one quasi-reversible redox couple at half wave potential of -0.57 V vs SCE in aqueous solution containing 0.1 M KCl. The surface coverage of C(60) on the gold surfaces was estimated to be 1.1 x 10(-10) mol cm(-2). The XPS showed the assembly of C(60) over the thiolated beta-CD SAMs. The surface hydrophobicity increased greatly upon the formation of the C(60)-containing SAMs as analyzed by water contact angle measurements. The results are in agreement with the formation of 1:1 complex of C(60) and cyclodextrin on gold surfaces, though it also reveals some non-homogeneous features of the monolayers.     

Surface composition and electrical and electrochemical properties of freshly deposited and acid-etched indium tin oxide electrodes

We compare the near-surface composition and electroactivity of commercial indium tin oxide (ITO) thin films, activated by plasma cleaning or etching with strong haloacids, with ITO films that have been freshly deposited in high vacuum, before and after exposure to the atmosphere or water vapor. Conductive-tip AFM, X-ray photoelectron spectroscopy (XPS), and the electrochemistry of probe molecules in solution were used to compare the relative degrees of electroactivity and the near-surface composition of these materials. Brief etching of commercial ITO samples with concentrated HCl or HI significantly enhances the electrical activity of these oxides as revealed by C-AFM. XPS was used to compare the composition of these activated surfaces, focusing on the intrinsically asymmetric O 1s line shape. Energy-loss processes associated with photoemission from the tin-doped, oxygen-deficient oxides complicate the interpretation of the O 1s spectra. O 1s spectra from the stoichiometric indium oxide lattice are accompanied by higher-binding-energy peaks associated with hydroxylated forms of the oxide (and in some cases carbonaceous impurities) and overlapping photoemission associated with energy-loss processes. Characterization of freshly sputter-deposited indium oxide (IO) and ITO films, transferred under high vacuum to the surface analysis environment, allowed us to differentiate the contributions of tin doping and oxygen-vacancy doping to the O 1s line shape, relative to higher-binding-energy O 1s components associated with hydroxyl species and carbonaceous impurities. Using these approaches, we determined that acid activation and O2 plasma etching create an ITO surface that is still covered with an average of one to two monolayers of hydroxide. Both of these activation treatments lead to significantly higher rates of electron transfer to solution probe molecules, such as dimethyferrocene in acetonitrile. Solution electron-transfer events appear to occur at no more than 4x10(7) electroactive sites per cm2 (each with diameters of ca. 50-200 nm) (i.e., a small fraction of the geometric area of the electrode). Electron-transfer rates correlate with the near-surface tin dopant concentration, suggesting that these electroactive sites arise from near-surface tin enrichment.     

Multiredox tetrathiafulvalene-modified oxide-free hydrogen-terminated Si(100) surfaces

Tetrathiafulvalene (TTF) monolayers covalently bound to oxide-free hydrogen-terminated Si(100) surfaces have been prepared from the hydrosilylation reaction involving a TTF-terminated ethyne derivative. FTIR spectroscopy characterization using similarly modified porous Si(100) substrates revealed the presence of vibration bands assigned to the immobilized TTF rings and the Si-C═C- interfacial bonds. Cyclic voltammetry measurements showed the presence of two reversible one-electron systems ascribed to TTF/TTF(.+) and TTF(.+)/TTF(2+) redox couples at ca. 0.40 and 0.75 V vs SCE, respectively, which compare well with the values determined for the electroactive molecule in solution. The amount of immobilized TTF units could be varied in the range from 1.7 × 10(-10) to 5.2 × 10(-10) mol cm(-2) by diluting the TTF-terminated chains with inert n-decenyl chains. The highest coverage obtained for the single-component monolayer is consistent with a densely packed TTF monolayer.     

Selective anion sensing by a tris-amide CTV derivative: 1H NMR titration, self-assembled monolayers, and impedance spectroscopy

A hydrogen-bond forming tris(amide) receptor based on cyclotriveratrylene (CTV) was prepared. Self-assembled monolayers (SAMs) of the receptor were formed on gold surfaces. Desorption experiments show a surface coverage of 2.26 x 10(-10) mol/cm(2). (1)H NMR and UV measurements confirm that the receptor exhibits the highest affinity for acetate ions among the anions studied. Electrochemical impedance was used to investigate anion sensing by the SAMs and proved to be an efficient and convenient technique for detecting anions in aqueous solutions. Upon binding acetate anions, the monolayer-modified gold electrodes show a drastic increase of the R(ct) values when Fe(CN)(6)(3-/4-) is used as the redox probe. When the probe was changed to a positively charged one, Ru(NH3)(6)(3+/2+), the R(ct) values decreased monotonically as the acetate concentration was increased, thus confirming the accumulation of negative surface charge upon anion binding. H(2)PO(4-) shows some interference when sensing AcO-. Other monovalent anions such as Cl-, Br-, NO3(-) and HSO4(-) do not bind to the CTV receptor either in solution or on the surfaces.     

Immobilization and electrochemical redox behavior of cytochrome c on fullerene film-modified electrodes

Two different fullerene film-modified electrodes were prepared and used for surface immobilization and electrochemical property investigation of horse heart cytochrome c (cyt c). Both a pristine fullerene film and fullerene-palladium (C(60)-Pd) polymer film-modified platinum, glassy carbon and indium-tin-oxide (ITO) electrodes were used. The immobilized cyt c was characterized by piezoelectric microgravimetry at a quartz crystal microbalance (QCM), UV-visible absorption, and X-ray photoelectron spectroscopy (XPS), as well as cyclic voltammetry (CV) techniques. The UV-visible spectral studies revealed a small blue shift of both the Soret and Q band of the heme moiety of cyt c, immobilized on the C(60)-Pd polymer film-modified ITO electrode, as compared to the bands of cyt c in solution suggesting that molecules of cyt c are densely packed onto the surface of the modified electrode. The CV studies revealed a quasi-reversible electrode behavior of the heme moiety indicating the occurrence of kinetically hindered electron transfer. A good agreement was found between the values of cyt c electrode surface coverage determined by piezoelectric microgravimetry and cyclic voltammetry. For piezoelectric microgravimetry, these values ranged from 0.5 x 10(-10) to 2.5 x 10(-10) mol cm(-2), depending upon the amount of cyt c present in solution and the time allowed for immobilization, which compared with a value of 3.6+/-0.4 x 10(-10) mol cm(-2) determined by CV. The possible mechanisms of cyt c immobilization on the C(60) film and C(60)-Pd film-modified electrodes are also discussed.     

三维有序石墨烯掺杂纳米二氧化钛酶生物传感器

采用模板法在氧化铟锡电极上制备了三维有序多孔结构的石墨烯掺杂纳米二氧化钛修饰电极,并在此修饰电极上成功固定了过氧化氢酶,从而构建了一种新型的H2O2生物传感器。 通过循环伏安、交流阻抗及计时电流等方法研究了该修饰电极的电化学特性,实验结果表明,该修饰电极对H2O2有良好的电催化作用,对H2O2的检测线性范围为3.0×10-6~3.6×10-3 mol/L,检测限为4.2×10-7 mol/L(S/N=3);且传感器响应迅速、灵敏度高、重现性和稳定性好。     

基于分子信标末端现场标记三聚氰胺-Cu~(2+)电活性分子的高灵敏电化学传感器

本文构建了一种基于分子信标自由末端现场标记电活性信号分子的新型DNA传感器.首先将3′修饰巯基的分子信标通过Au–S键自组装到金电极表面,然后在修饰有羧基的5′自由末端通过共价偶合和配位作用依次组装上三聚氰胺(Mel)和铜离子(Cu2+),得到以Mel-Cu2+配合物为电活性信号源的分子信标.该方法简单实现了电活性分子信标的标记、分离和纯化.以[Fe(CN)6]3-/4-为电化学探针,采用循环伏安和电化学阻抗法对层层自组装过程进行了表征.杂交实验表明,Mel-Cu2+信号源所对应的峰电流强度随着杂交液浓度的增大逐渐降低,且氧化峰电流与互补序列浓度对数在1.0×10-15~1.0×10-9 mol/L范围内呈良好的线性关系.根据3σ计算得到检测限为2.4×10-16 mol/L.另外,由于分子信标特殊的茎环结构特征和Mel-Cu2+信号源稳定的无机配位组成,传感器显示了很高的特异性、再生性和稳定性.     

Structural characterization of (3-mercaptopropyl)sulfonate monolayer on gold surfaces

We have investigated the structure of (3-mercaptopropyl)sulfonate (MPS) monolayer self-assembled onto gold surfaces by quartz crystal microbalance with energy dissipation monitoring (QCM-D) and various electrochemical methods. QCM-D experiments show that the MPS monolayer behaves as a thin rigid film with a surfacic mass of 166 ng cm(-2). Interfacial capacitance measurements demonstrate that the MPS monolayer is a rather open structure that can be penetrated by the ionic species of the phosphate buffer electrolyte. From MPS reductive desorption experiments, MPS surface concentration corresponds to 4.6 x 10(-10) mol cm(-2), which represents 60% of the coverage reported for a densely packed thiol monolayer. Despite this low packing density, oxidation of catechol is strongly inhibited leading to voltammograms that are free ofdiffusional contribution. This unique behavior has been exploited to show that the MPS monolayer covers the entire gold surface with a surface coverage at least equal to theta = 0.9981, which means a very low number of MPS-free pinholes and/or defects. Kinetics of electron transfer toward soluble redox species has been studied using catechol as a neutral hydrophilic probe, but also ferrocyanide as hydrophilic anion and ferrocenemethanol as neutral hydrophobic molecule. It is proposed that the MPS monolayer provides a high kinetic barrier toward permeation of these species and that electron transfer mainly occurs by electron tunneling through the MPS monolayer.     

Surface-immobilized pyridine-functionalized gamma-cyclodextrin: alkanethiol co-adsorption-induced reorientation

Monolayers of di-6A,6B-deoxy-6-(4-pyridylmethyl)amino-gamma-cyclodextrin (gamma-CD-(py)2) have been formed on polycrystalline platinum electrodes and investigated using electrochemical and surface-enhanced Raman spectroscopy (SERS). The behavior of self-assembled monolayers of (gamma-CD-(py)2) alone, (gamma-CD-(py)2) backfilled with 1-nonanethiol, and 1-nonanethiol are reported. The potential dependence of the capacitance indicates that the film capacitance is higher for the backfilled CD layers than for 1-nonanethiol layers, most likely due to ion flux through the CD cavity. SERS spectra of the backfilled layer exhibit features associated with both pyridine-functionalized CD and alkane moieties. Investigations using [Fe(CN)6]4- as a solution-phase probe indicate that the backfilled CD-alkane thiol layer exhibits enhanced blocking properties compared to gamma-CD-(py)2 films alone. Complete blocking was achieved by a combination of backfilling and insertion of a high-affinity guest 1-adamantylamine into the cavity. Significantly, an electroactive guest with high affinity for gamma-CD, [Co(biptpy)2]2+, does not exhibit a redox response at the gamma-CD-(py)2 layer but molecular recognition is turned on by backfilling the CD layer with 1-nonanethiol molecules. This switching on of the electrochemical activity suggests that the CD hosts are initially inaccessible but reorientate upon backfilling, exposing the CD opening to solution and permitting a supramolecular host-guest complex to form. The binding of [Co(biptpy)2]2+ to gamma-CD in the backfilled monolayer depends on the bulk concentration of guest and is modeled by the Langmuir isotherm, yielding an association constant for the Co2+ state of 1.45 +/- 0.46 x 105 M-1 and a limiting surface coverage 1.49 +/- 0.25 x 10-11 mol cm-2. The surface coverage of the divalent state is higher than the trivalent state, reflecting the dynamic nature of the inclusion.     

Viscosity of the aqueous liquid/vapor interfacial region: 2D electrochemical measurements with a piperidine nitroxy radical probe

Surface partitioning of 2,2,6,6-tetramethyl-1-piperidynyloxy radical (Tempo) to the air/water interface follows a Langmuir isotherm. The partition constant was obtained by the surface tension measurements in the concentration range of 1.0 x 10(-4)-2.4 x 10(-3) M yielding K = 640 +/- 99 M(-1). The lateral mobility of Tempo at the air/water interface was measured electrochemically in the surface concentration range of 2.0 x 10(-11)-1.4 x 10(-10) mol/cm2, corresponding to ca. 7.3-50% full monolayer coverage. The measurements employed cyclic voltammetry with line microelectrodes touching the air/water interface. The Tempo lateral diffusion constant of (1.5 +/- 0.7) x 10(-4) cm2/s is independent of surface concentration below 4.0 x 10(-11) mol/cm2. The extent of Tempo water interactions was assessed by the electronic structure calculations. These calculations showed that, at most, two water molecules can hydrogen bond with the oxygen atom of the nitroxyl group of Tempo, and that a single water molecule forms a hydrogen bond that is ca. 30% stronger than the H2O-H2O hydrogen bond. These calculations led to a postulate that Tempo diffuses along the interface largely unimmersed, and that it is coupled to the interfacial water via hydrogen bonding with H2O. In view of this postulate, the viscosity of the aqueous liquid/vapor interfacial region obtained by interpreting the Tempo diffusion constant in the low concentration region is as much as 4 times smaller than that of bulk liquid water.     

Grafting of single, stimuli-responsive poly(ferrocenylsilane) polymer chains to gold surfaces

Redox-responsive poly(ferrocenylsilane) (PFS) polymer molecules were attached individually to gold surfaces for force spectroscopy experiments on the single molecule level. By grafting ethylenesulfide-functionalized PFS into the defects of preformed self-assembled monolayers (SAMs) of different omega-mercaptoalkanols on Au(111), the surface coverage of PFS macromolecules could be conveniently controlled. Atomic force microscopy (AFM), contact angle, as well as cyclic and differential pulse voltammetry measurements were carried out to characterize the morphology, wettability, and surface coverage of the grafted layers. The values of the PFS surface coverage were found to depend on the chain length of the omega-mercaptoalkanol molecules and on the concentration of the PFS solution but not on the insertion time or on the molar mass of PFS. The equilibrium surface coverages were successfully described by Langmuir adsorption isotherms. For low-surface coverage values (< 6.2 x 10(-4) chain/nm2), achieved by PFS insertion from very dilute solutions (8 x 10(-6) M) into long-chain SAMs, AFM and differential pulse voltammetry showed that surfaces exposing isolated individual polymer chains were obtained. The isolated PFS macromolecules were subjected to in situ AFM-based single molecule force spectroscopy (SMFS) measurements. The single chain elasticity of PFS in isopropanol (and ethanol) was fitted with the modified freely jointed chain (m-FJC) model. This procedure yielded a Kuhn segment length of 0.33 +/- 0.05 nm and a segment elasticity of 32 +/- 5 nN/nm.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase in alpha-zirconium phosphate nanosheet film

Alpha-zirconium phosphate nanosheets (ZrPNS) derived via the delamination of layered alpha-zirconium phosphate (alpha-ZrP) have been proven to be efficient support matrixes for the immobilization of horseradish peroxidase (HRP). X-ray powder diffraction (XRD) results revealed that ZrPNS in HRP-ZrPNS film remained unorderly structured for the effect of HRP. Fourier transform infrared (FTIR) spectra results revealed that HRP remained the secondary structure in HRP-ZrPNS film. The direct electrochemistry of HRP was realized in HRP-ZrPNS film on a glassy carbon electrode (GCE), showing a pair of well-defined, nearly reversible cyclic voltammetry (CV) peaks for the HRP heme Fe(III)/Fe(II) redox couple. The average surface concentration (Gamma(*)) of electroactive HRP in HRP-ZrPNS film was estimated to be 1.35x10(-10) mol cm(-2), which indicated a high loading of enzyme molecules in HRP-ZrPNS film. Based on these, a third generation reagentless biosensor was constructed for the determination of hydrogen peroxide (H(2)O(2)). The response time of the biosensor was less than 3 s, and the linear response range of the biosensor for H(2)O(2) was from 1.3x10(-6) to 1.6x10(-2) M with a correlation coefficient of 0.9997.     

Self-assembled monolayer of organic iodine on a Au surface for attachment of redox-active metal clusters

The attachment of a bifunctional iodo-organo-phosphinate compound to gold (Au) surfaces via chemisorption of the iodine atom is described and used to chelate a redox-active metal cluster via the phosphinate group. XPS, AFM, and electrochemical measurements show that (4-iodo-phenyl)phenyl phosphinic acid (IPPA) forms a tightly bound self-assembled monolayer (SAM) on Au surfaces. The surface coverage of an IPPA monolayer on Au was quantified by an electrochemical method and found to be 0.40 +/- 0.03 nmol/cm2, roughly corresponding to 0.4 monolayers. We show that the Au/IPPA SAM, but not the underivatized Au, adsorbs Mn4O4(Ph2PO2)6 from solution by a phosphinate exchange reaction to yield Au/IPPA/Mn4O4(Ph2PO2)5 SAM. The resulting SAM is firmly bound and not removed by sonication, as confirmed by manganese XPS (Mn 2p1/2) and by AFM. Electrochemistry confirms that Mn4O4(Ph2PO2)6 is anchored on the Au/IPPA surface and that redox chemistry can be mediated between the electrode and the surface-attached complex. Mn4O4(Ph2PO2)6 contains the reactive Mn4O46+ cubane core, a redox-active bioinspired catalyst.     

Electrochemical characteristics of ferrocenecarboxylate-coupled aminoundecylthiol self-assembled monolayers

The electrochemical characteristics of the modified electrodes with ferrocenecarboxylate-coupled aminoundecylthiol monolayers prepared in two sequential steps were studied. The self-assembled monolayer (SAM) was prepared through the covalent attachment of ferrocenecarboxylate in an activation solution containing N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide coupling agent to aminoundecylthiol SAMs formed on a substrate. In the ferrocenecarboxylate-coupled aminoundecylthiol monolayers, the ferrocene moieties were expected to be packed regularly with enhanced ordering compared with those in the FcCOO(CH2)11SH monolayer. As the ferrocene coverage increases, the formal potential for the ferrocene-ferricenium (Fc/Fc+) couple shifts to the positive potential and the full width at half-maximum (deltaE(fwhm)) increases also. The maximum coverage is found to be about 3 x 10(-10) mol cm(-2), which is considered to be a value obtained from a well-ordered ferrocene-tethered SAM. As for the mass change, the increase in ferrocene coverage caused the enhancement in ion association between the ferricenium cations and perchlorate anions resulting in a mass increase upon oxidation; however, the mass change per mole electron decreases. The results obtained from the ferrocenecarboxylate-coupled aminoundecylthiol monolayers were explained to be due to the well-ordered packing with regular spacing compared with those of the FcCOO(CH2)11SH monolayer.     

A tripodal [2]rotaxane on the surface of gold

Tripodal [2]rotaxane, 3, and the structurally related axle, 2, incorporating a viologen moiety, a crown ether, and three thiol anchoring groups have been synthesized. Analogous monopodal derivatives, 1, have also been prepared. Self-assembled monolayers of the above tripodal and monopodal systems on gold have been studied by cyclic voltammetry. It has been shown that a thiol anchoring group is required to attach the monopodal viologen 1 to the surface of gold and that the maximum surface coverage of 1 corresponds to 2.7 x 10(-10) mol.cm(-2). The adsorbed monopodal viologen 1 does not thread bis-p-phenylene-34-crown-10 ether, 6. However, the tripodal axle 2 adsorbed on the surface of gold threads the crown ether 6 to form a hetero [2]rotaxane. In the case of the tripodal axle 2, the surface coverage is 7 x 10(-11) mol.cm(-2), while for the tripodal [2]rotaxane 3 the surface coverage reaches 1.1 x 10(-10) mol.cm(-2).