Coarsening of the phase structure in immiscible polymer blends. Coalescence or ostwald ripening?

The results of theories of the Ostwald ripening and coalescence applied to molten quiescent polymer blends with dispersed phase structure were analyzed. From a comparison of predictions of the theories with available experimental results follows that coarsening of the phase structure in quiescent polymer blends with medium or high interfacial tension is induced by the coalescence. Both the mechanisms play a role in coarsening of the phase structure in blends with low interfacial tensions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 181–187, 1999     

Prediction of the phase structure in polymer blends: what is needed for success?

Rules for prediction of the phase structure in immiscible polymer blends from the knowledge of their composition, component properties and the flow field in a mixing or processing device are discussed. The reliability of qualitative prediction of the dependence of phase structure on system parameters is used as a criterion of plausibility of the rules. No general reliable rule for prediction of the phase structure type (continuity of phases) is available in the literature. Dependence of the droplet break‐up frequency on its size, contribution of simultaneous collisions of three or more droplets to coalescence and the effect of complex flow field on coalescence must be better described for a reliable qualitative prediction of the dependence of the droplet size on the system parameters.     

Effect of temperature gradient on the development of β phase polypropylene in dynamically vulcanized PP/EPDM blends

Different sample thicknesses were adopted to investigate the effect of temperature gradient on the development of β phase polypropylene (PP) in the compression-molded dynamically vulcanized thermoplastic elastomers (TPVs) based on PP/ethylene-propylene-diene rubber blend. Differential scanning calorimetry and wide-angle X-ray diffraction were employed to study the melting behavior and crystalline structures. The results indicated that the content of β phase increased with the sample thickness of TPV increasing, while the total crystallinity of PP almost kept constant. The simulation of the temperature field showed that there was a temperature gradient along the direction of sample thickness, and the strength of the temperature gradient increased with the thickness of TPV increasing. The reason for the change of β phase content was found to lie in the reduction of the entropy in the temperature gradient field, which was a result from the decrease of the molecular chain conformation.     

Diffusion and phase equilibria of binary fluids in mesopores

The formation of adsorption hysteresis in mesoporous material with random pore structure may be interrelated with different distributions of the fluid density attained along different paths of the system preparation. To access microscopic details of these distributions, in addition to the main sorptive liquid, distribution of which along the pore space of Vycor porous glass was of interest, a small amount of a probe liquid with a substantially lower vapor pressure has been added. Molecular diffusivities of both liquids then have been traced using pulsed field gradient NMR. Due to different vapor pressures, the two molecular species explore different spaces occupied by the capillary-condensed (accessible for both species) and gaseous (accessible only for the molecules of the main sorptive) phases. Comparative analysis of the diffusion properties obtained at different states along the adsorption isotherm revealed further insight into peculiarities of the fluid distribution and mass transfer of binary fluids in pores.     

The rotation and the phase transition in solid C60

The interaction between C60's in solid C60 has been calculated by (exp-6-1) potential, and the cause and the controlled factor of the high rapid rotations of C60 's were discussed. In order to describe the disordered degree of C60 rotation, an equivalent M is introduced. The phase transitions at the ~260 K and at the ~90 K are studied from the viewpoint of C60 rotation. The potential barriers of the ordered rotation below the ~260 K and the disordered rotation above the ~260 K have been given, and the effect of the external pressure on the temperature of phase transition has also been given.     

Amplitude and phase fluctuation modes in the smectic Cα* phase of an antiferroelectric compound

Dielectric measurements have been carried out on the chiral smectic C_α (SmC_α*) phase of a MHPOBC analogous compound. Two relaxation modes have been observed in this phase for planar orientation of the molecules. One process has been observed at frequency lower than that of the soft mode of the chiral smectic A (SmA*) phase. This relaxation process is connected with the helicity of the SmC_α* phase. In the high‐frequency region, another relaxation process has been observed in the SmC_α* phase for which bias field dependence is similar to that of the soft mode at the SmA*–SmC* phase transition. The experimental observations are in agreement with a recently proposed dielectric theory for the SmC_α* phase and theoretical dielectric results obtained by numerical simulations. Thus, we report here experimental verification of two theoretically predicted dielectric modes in the SmC_α* phase.     

High-performance liquid chromatography–tandem mass spectrometry in the identification and determination of phase I and phase II drug metabolites

Applications of tandem mass spectrometry (MS/MS) techniques coupled with high-performance liquid chromatography (HPLC) in the identification and determination of phase I and phase II drug metabolites are reviewed with an emphasis on recent papers published predominantly within the last 6 years (2002–2007) reporting the employment of atmospheric pressure ionization techniques as the most promising approach for a sensitive detection, positive identification and quantitation of metabolites in complex biological matrices. This review is devoted to in vitro and in vivo drug biotransformation in humans and animals. The first step preceding an HPLC-MS bioanalysis consists in the choice of suitable sample preparation procedures (biomatrix sampling, homogenization, internal standard addition, deproteination, centrifugation, extraction). The subsequent step is the right optimization of chromatographic conditions providing the required separation selectivity, analysis time and also good compatibility with the MS detection. This is usually not accessible without the employment of the parent drug and synthesized or isolated chemical standards of expected phase I and sometimes also phase II metabolites. The incorporation of additional detectors (photodiode-array UV, fluorescence, polarimetric and others) between the HPLC and MS instruments can result in valuable analytical information supplementing MS results. The relation among the structural changes caused by metabolic reactions and corresponding shifts in the retention behavior in reversed-phase systems is discussed as supporting information for identification of the metabolite. The first and basic step in the interpretation of mass spectra is always the molecular weight (MW) determination based on the presence of protonated molecules [M+H]⁺ and sometimes adducts with ammonium or alkali-metal ions, observed in the positive-ion full-scan mass spectra. The MW determination can be confirmed by the [M-H]^- ion for metabolites providing a signal in negative-ion mass spectra. MS/MS is a worthy tool for further structural characterization because of the occurrence of characteristic fragment ions, either MS ⁿ analysis for studying the fragmentation patterns using trap-based analyzers or high mass accuracy measurements for elemental composition determination using time of flight based or Fourier transform mass analyzers. The correlation between typical functional groups found in phase I and phase II drug metabolites and corresponding neutral losses is generalized and illustrated for selected examples. The choice of a suitable ionization technique and polarity mode in relation to the metabolite structure is discussed as well.     

Degradation of polymer blends—II. Oxidative radiolysis and stabilization of blends of low-density polyethylene and styrene-butadiene-styrene copolymers

The solubility, infra-red and mechanical properties have been studied for LDPE-SBS blends irradiated with γ-rays in the presence of oxygen. The results have been compared with those obtained for the oxidative radiolysis of pure LDPE and for the photo-oxidation of the same LDPE-SBS blend. The oxidative degradation mainly occurs in the polybutadiene part of the blend. Efficient stabilization by hindered amines Tinuvin 770 is reported.     

Liquid—liquid equilibrium in methanol + gasoline blends

An investigation has been carried out to study the limited miscibility of methanol and gasoline blends over the temperature range −20 to 20°C. Two liquid phases in equilibrium were analysed by mass spectrometric methods and their composition reported, in addition to the methanol content, in terms of six principal classes of hydrocarbons. Liquid—liquid equilibrium was predicted using the UNIFAC group contribution model. In liquidliquid equilibrium calculations, gasoline was represented by a set of model compounds. The number of the different groups that comprise each model molecule was determined using the result of a distillation analysis and the paraffin—naphthene—aromatic composition. Estimation of conjugate phase composition using the UNIFAC model is reasonable at temperatures above 0°C. To describe correctly the limited miscibility of methanol+gasoline blends over the whole temperature range studied, we found that ‘specific’ UNIFAC interaction parameters were necessary.     

Crystalline phase content and ionic conductivity correlation in LATP glass–ceramic

Li₂O–Al₂O₃–TiO₂–P₂O₅ (LATP) glass was fabricated by conventional melt quenching route. Glass transition temperature (T _g = 296 °C) and crystallization temperatures (T _C1,2) were obtained from thermal analysis. LATP glass was converted to glass–ceramic by heat treatment in the range 550–950 °C for 6 h. X-ray diffraction analysis revealed LiTi₂(PO₄)₃ as a major phase. Ionic conductivity increased monotonically with concentration, reaching a maximum of ~10⁻⁴ S/cm. AlPO₄ phase was detected in samples heat-treated above 850 °C. Its presence decreased the conductivity, suggesting LiTi₂(PO₄)₃ phase as main contributor to high ionic conductivity. NMR spectra confirmed the presence of mobile ⁷Li ions in the entire sample series and also gave some information on the structure and dynamics of conductivity.     

Solid and liquid phase equilibria and solid-hydrate formation in binary mixtures of water with amines

Solid and liquid phase diagrams have been constructed for {water+triethylamine,or+N,N-dimethylformamide(DMF) or+N,N-dimethlacetamide (DMA)} Solid-hydrates form with the empirical formulae N(C2H5)3 3H2O,DMF 3H2O,DMF 2H2O,DMA 3H2O and (DMA)2 3H2O.All are congruently melting except the first which melts incongruently.The solid-hydrate formation is attributed to hydrogen bond.The results are compared with the references     

Hydrogen absorption and phase transitions in rapidly quenched LaNi alloys

Several LaNi binary alloys were rapidly quenched by melt spinning. A metastable phase and an uniform Laves phase were obtained. Differences in behaviour were observed between hydrogenation of quenched materials and of as-cast materials whose compositions were identical. The quenched materials, in contrast to the as-cast phases, had a tendency to form amorphous LaNiH alloys. The amorphous alloy was stable, in particular when the ratio La:Ni was 1:2.     

Ab initio study of tautomerism and hydrogen bonding of β-carbonylamine in the gas phase and in water solution

All the possible conformations of the three tautomeric isomers of simple β-carbonylamine were fully optimized at ab initio MP2/6-31G** and B3LYP/6-31G** levels in order to determine the conformational equilibrium and the energies of the O—H···N and O···H—N hydrogen bridges. For the most interesting conformations, further calculations in water solution were also carried out. It was found that carbonylamine is the most stable tautomer, followed by enolimine and carbonylimine. This order of stability does not change in solution. O—H···N is the strongest hydrogen bridge, but in solution its energy as well as that of the O···H—N one are dramatically lowered. The deprotonation energy was also calculated and discussed. Received: 16 September 1999 / Accepted: 3 February 2000 / Published online: 5 June 2000     

Role of precursors and coating polymers in sol–gel chemistry toward enhanced selectivity and efficiency in solid phase microextraction

To evaluate the selectivity and efficiency of solid phase microextraction (SPME) fiber coatings, synthesized by sol–gel technology, roles of precursors and coating polymers were extensively investigated. An on-line combination of capillary microextraction (CME) technique and high performance liquid chromatography (HPLC) was set up to perform the investigation. Ten different fiber coatings were synthesized in which five of them contained only the precursor and the rests were prepared using both the precursor and coating polymer. All the coatings were chemically bonded to the inner surface of copper tubes, intended to be used as the CME device and already functionalized by self-assembly monolayers of 3-(mercaptopropyl)trimethoxysilane (3MPTMOS). The selected precursors included tetramethoxysilane (TMOS), 3-(trimethoxysilyl)propylmethacrylate (TMSPMA), 3-(triethoxysilyl)-propylamine (TMSPA), 3MPTMOS, [3-(2,3-epoxypropoxy)-propyl]-trimethoxysilane (EPPTMOS) while poly(ethyleneglycol) (PEG) was chosen as the coating polymer. The effects of different precursors on the extraction efficiency and selectivity, was studied by selecting a list of compounds ranging from non-polar to polar ones, i.e. polycyclic aromatic hydrocarbon, herbicides, estrogens and triazines. The results from CME–HPLC analysis revealed that there is no significant difference between precursors, except TMOS, in which has the lowest extraction efficiency. Most of the selected precursors have rather similar interactions toward the selected analytes which include Van der Walls, dipole–dipole and hydrogen bond while TMOS has only dipole–dipole interaction and therefore the least efficiency. TMOS is silica but the other sorbents are organically modified silica (ORMOSIL). Our investigation revealed that it is rather impossible to prepare a selective coating using conventional sol–gel methodologies. The comparison study performed among the fiber coatings contained only a precursor and those synthesized by a precursor along with coating polymer proved that the extraction efficiency obtained for all coatings are the same. This is an indication that by selecting the appropriate precursor there is no need to use any coating polymer. In overall, a fiber coating in sol–gel process could be synthesize with no coating polymer which leads to faster, easier, cheaper and more controllable synthesis.     

Thermodynamics of the solvation and phase distributions of 2,2′-dipyridyl in acetonitrile-DMSO-hexane and methanol-DMSO-hexane systems

The Gibbs energies of 2,2′-dipyridyl when transferred from dimethyl sulfoxide to its mixtures with acetonitrile and methanol are determined from the distribution of substance between immiscible phases. It is found that moving from dimethyl sulfoxide to acetonitrile and methanol weakens the solvation of 2,2′-dipyridyl due to a change in the solvation of amino groups and the hydrocarbon substituent, which is reflected in a reduction in the entropy component of the Gibbs energy.     

Calorimetric and SEM studies of PHB–PET polymeric blends

PHB [poly (3-hydroxybutyrate)], post-consumer soft-drink bottles poly (ethylene terephthalate) PET (herein named PET-R) and PHBPET-R (blends of PHB and PET-R in several compositions) samples were evaluated by differential scanning calorimetry (DSC) and scanning electronic microscopy (SEM) in order to verify their thermal properties and porosity according to amounts of PET-R added the blends. The DSC curve showed that the solvents used to solve the polymer mixture cause changes in the thermal behavior of PET-R films and in PHBPET-R blends. SEM studies of the PHBPET-R blends show that with a gradual mass increase of PET-R, there are gradual increases in the porosity of the films.     

Calculated vertical ionization energies of the common α-amino acids in the gas phase and in solution

The vertical ionization energies of the low-lying conformers of the α-amino acids found in proteins have been calculated. Geometry optimizations were first performed at the B3LYP/6-311G(d,p) level of theory, and then reoptimized at the MP2/6-311G(d,p) level of theory. Vertical ionization energies were then computed by three methods, electron propagator in the partial third-order (P3) approximation, Outer-Valence-Green's Functions, and by evaluating the difference in the total energy between the cation radical and the neutral amino acid in the geometry of the neutral species. When available, the results are compared to the experimental vertical ionization energies. The vertical ionization energies calculated using the MP2/P3 method gave the best overall agreement with the experimental results. Next, the ionization energies in solution are calculated for the zwitterionic forms of the α-amino acids by using IEFPCM methods. To obtain the vertical ionization energy in solution, it is necessary to use the nonequilibrium polarizable continuum model (NEPCM), the results of which are reported here for the α-amino acids.     

Simultaneous enantiomeric determination of MDMA and its phase I and phase II metabolites in urine by liquid chromatography–tandem mass spectrometry with chiral derivatization

A liquid chromatography–electrospray ionization tandem mass spectrometry (LC-ESI-MS/MS) procedure was developed for the simultaneous determination of enantiomers of the prevalent designer drug 3,4-methylenedioxymethamphetamine (MDMA) and its phase I and phase II metabolites in urine with chiral derivatization. The analytes in urine were directly derivatized with chiral Marfey’s reagent, N ^α- (5-fluoro-2,4-dinitrophenyl)-d-leucinamide, without extraction. The diastereomers of the N ^α-(2,4-dinitrophenyl)-d-leucinamide derivatives generated were determined by LC-MS/MS. Satisfactory chromatographic separation was achieved for the enantiomers of MDMA and its metabolites 3,4-methylenedioxyamphetamine, 4-hydroxy-3-methoxymethamphetamine (HMMA), HMMA glucuronide, and HMMA sulfate on a semimicro octadecylsilane column using linear gradient elution. With use of multiple reaction monitoring mode, the limits of detection of these analytes ranged from 0.01 to 0.03?μg/mL. Linear calibration curves were obtained for all enantiomers from 0.1 to 20?μg/mL in urine. The method showed sufficient reproducibility and quantitative ability. This is the first report of a simple LC-MS/MS-based analytical procedure with direct chiral derivatization in aqueous media that allows simultaneous enantiomeric determination of drugs and their metabolites, including glucuronide and sulfate derivatives.     

Thermodynamic characteristics and phase equilibria in the alloys of the Ge–La system

Mixing enthalpies of melts of the Ge–La system have been measured using isoperibolic calorimetry within two concentration ranges. For the first range (0 < x _La < 0.16 at 1520 K and 0.16 < x _La < 0.29 at 1570 K), agreement with the known literature data is observed within the experimental error. The second range (0.78 < x _La < 1 at 1470 K and 0.7 < x _La < 0.78 at 1580 K) has been studied for the first time. The melts are characterized by very strong exothermal effects of mixing, which have almost symmetrical concentration dependence: ΔH? _La ^∞ = ΔH? _Ge ^∞ = ?245 kJ/mol at 1470 K. A thermodynamic optimization of the activities of the components and the phase diagram of the system have been conducted based on the obtained experimental data, using an ideal associated solution (IAS) model.