Cu-LaCoO3催化剂选择氢解生物质基糠醇制备1,5-和1,2-戊二醇

高效转化可再生生物质资源制备人类社会必需的燃料和化学品是当前关注和研究的热点之一.生物质基糠醇来源于玉米芯、甘蔗渣、秸秆等农林副产物,价廉易得,是选择氢解合成高附加值1,2-和1,5-戊二醇的理想原料.目前生物质基呋喃衍生物氢解制备二元醇的研究主要集中在Pt,Ru,Rh和Ir等贵金属催化剂,对无Cr非贵金属催化剂的研究甚少.基于纳米Cu催化剂较高的C-O键氢解活性和较低的C-C键裂解活性,以及碱性载体对反应物和反应中间体的稳定作用,我们在前期Cu-Mg3AlO4.5和Cu-Al2O3催化剂催化糠醇氢解研究基础上,以具有一定碱性的ABO3结构的钙钛矿型化合物为载体负载活性Cu开展糠醇氢解研究,深入研究催化剂结构、组成和活性金属价态等对催化剂活性和选择性影响,并研究了催化剂循环使用稳定性.首先我们采用柠檬酸一步络合法制备了一系列具有一定钙钛矿结构的不同Cu负载量(0-20 wt％)的Cu-LaCoO3催化剂以及LaCoO3负载的5 wt％Pt,Ru,Rh和Pd催化剂并考察了它们的糠醇选择氢解制备戊二醇性能.研究发现,在相同活性金属负载量(5 wt％)时,Cu-LaCoO3催化剂具有较优异的呋喃环C-O键氢解活性,而贵金属催化剂倾向于催化呋喃环C=C键加氢饱和.考察不同Cu负载量的Cu-LaCoO3催化剂催化糠醇氢解性能发现,随着Cu负载量的增加,糠醇转化率先升高后降低,在10 wt％Cu负载量时达最高(94.6％),戊二醇总选择性也随Cu负载量的增加先升高后降低,在5 wt％Cu负载量时最高(52.2％),总体以10 wt％Cu负载量催化剂表现出最优异的性能.接着我们考察了反应动力学条件如温度、压力和反应时间以及还原处理条件对10 wt％Cu-LaCoO3催化性能的影响.研究发现适当的高温(～433 K)和高压(6 MPa H2)有利于Cu-LaCoO3催化糠醇氢解制戊二醇,而低浓度氢气(5 vol％)还原有利于1,5-戊二醇的生成,高氢气浓度(纯氢)还原有利于呋喃环加氢饱和的四氢糠醇生成.10 wt％Cu负载量的催化剂经5％H2-95％N2处理后,在413 K和6 MPa H2条件下可取得100％的糠醇转化率以及55.5％的戊二醇总选择性(其中1,5-戊二醇和1,2-戊二醇的选择性之比接近3:1).进一步考察了10 wt％Cu-LaCoO3催化剂的循环使用稳定性,研究发现无论是在高初始转化率(～93.7％)还是低初始转化率(～30.5％)条件下,经多次循环使用后糠醇转化率先升高后基本保持不变,而戊二醇总选择性呈下降趋势,四氢糠醇的选择性逐渐上升.结合XRD,XPS,BET,H2-TPR,CO2-TPD,NH3-TPD和HRTEM等多种表征技术对Cu-LaCoO3催化剂的结构及在糠醇氢解反应中的活性位进行了表征,发现高分散的活性物种、合适的碱性以及部分还原的活性组分均有利于提高催化剂的活性与1,5-戊二醇的化学选择性,高分散的Cu0与部分还原的Co3O4(很可能是CoO)之间的协同催化对于取得较优异的糠醇氢解性能,尤其是较高的1,5-/1,2-戊二醇比例至关重要.     

热扩散法制备MoO3/SiO2催化草酸二甲酯和苯酚酯交换反应

采用热扩散法（TS）和等体积浸渍法制备了MoO₃/SiO₂催化剂用于草酸二甲酯和苯酚酯交换反应.结果表明,热扩散法制备的10%MoO₃/SiO₂-TS催化剂较等体积浸渍法制备的10%MoO₃/SiO₂-C催化剂具有更好的催化性能.运用X射线衍射、Raman光谱、X射线光电子能谱分析、吡啶吸附红外光谱、NH₃程序升温脱附等手段对催化剂进行了表征,发现虽然两种方法制备的催化剂都只有弱Lewis酸中心,钼均以氧化钼单体形式存在,未形成解离和聚合,但是10%MoO₃/SiO₂-TS催化剂较10%MoO₃/SiO₂-C催化剂表面钼含量更高且MoO₃分散得更好.在苯酚用量为0.2mol,10%MoO₃/SiO₂-TS催化剂用量为1.2g,反应温度为180℃,草酸二甲酯与苯酚的摩尔比为2,反应时间为4h的优化条件下,苯酚转化率可达70.9%,甲基苯基草酸酯和草酸二苯酯的收率分别达63.1%和7.7%.     

Hydrogen Doping into MoO3 Supports toward Modulated Metal–Support Interactions and Efficient Furfural Hydrogenation on Iridium Nanocatalysts

As promising supports, reducible metal oxides afford strong metal–support interactions to achieve efficient catalysis, which relies on their band states and surface stoichiometry. In this study, in situ and controlled hydrogen doping (H doping) by means of H₂ spillover was employed to engineer the metal–support interactions in hydrogenated MoO_x‐supported Ir (Ir/H?MoO_x) catalysts and thus promote furfural hydrogenation to furfuryl alcohol. By easily varying the reduction temperature, the resulting H doping in a controlled manner tailors low‐valence Mo species (Mo⁵⁺ and Mo⁴⁺) on H?MoO_x supports, thereby promoting charge redistribution on Ir and H?MoO_x interfaces. This further leads to clear differences in H₂ chemisorption on Ir, which illustrates its potential for catalytic hydrogenation. As expected, the optimal Ir/H?MoO_x with controlled H doping afforded high activity (turnover frequency: 4.62 min^?1) and selectivity (>99 %) in furfural hydrogenation under mild conditions (T=30 °C, P =2 MPa), which means it performs among the best of current catalysts.     

Effects of CeO_2 preparation methods on the catalytic performance of MoO_3/CeO_2 toward sulfur-resistant methanation

CeO_2 supports were prepared by calcination or precipitation method and 5% MoO_3/CeO_2 catalysts were prepared by incipient-wetness impregnation method. The catalytic performance of the 5% MoO_3/CeO_2 catalysts toward sulfur-resistant methanation was investigated. The results showed that the Mo/Ce-1 catalysts with CeO_2 support prepared by calcination method exhibited the best sulfur-resistant methanation activity and stability with CO conversion as high as 75% while the Mo/Ce-3 catalysts the poorest. The supports and catalysts were characterized by N_2-adsorption–desorption, temperature-programmed reduction(TPR), X-ray diffraction(XRD), Raman spectroscopy(RS) and scanning electron microscope(SEM). The results indicated that the saturated monolayer loading MoO_3 on Ce-3 support was lower than 5% and there were some crystalline MoO_3 particles on the surface of the Mo/Ce-3. The preparation method of CeO_2 had a big influence on the specific surface area, the crystalline of CeO_2, and the catalytic performance of the corresponding Mo-based catalyst for sulfur-resistant methanation.     

Direct catalytic conversion of furfural to 1,5-pentanediol by hydrogenolysis of the furan ring under mild conditions over Pt/Co2AlO4 catalyst

A new strategy was developed for the direct conversion of furfural to 1,5-pentanediol by the hydrogenolysis of the furan ring under mild conditions based on Pt/Co(2)AlO(4) catalyst. This is the first report of the direct catalytic conversion of furfural to 1,5-pentanediol with high yield.     

Catalytic efficiency of cesium and potassium salts of dodecatungstophosphoric acid supported on silica and comparison with H<Subscript>3</Subscript>PW<Subscript>12</Subscript>O<Subscript>40</Subscript>/SiO<Subscript>2</Subscript>

Pure tungstophosphoric acid, potassium tungstophosphate, and cesium tungstophosphate with varying extent of substitution of protons by Cs or K ions x (x = 1, 2, 2.5, and 3) have been prepared and are supported on silica by the wet impregnation method. The extent of loading was fixed at 20 wt %. For the sake of comparison, unloaded Cs _x and K _x (x = 1) salts of tungstophosphoric acid were prepared by the precipitation method. The supported catalysts were characterized by FT-IR, XRD, specific surface area measurements, and catalytic conversion of tert-butanol. The results revealed that the catalytic conversion of tert-butanol proceeds mainly via dehydration yielding isobutene. The Cs₁PW/SiO₂, HPW/SiO₂, and K₁PW/SiO₂ catalysts were more active than their unsupported samples. The previous solids showed greater catalytic activity and stability. Unexpectedly, substitution of one proton of tungstophosphoric acid by a cesium or potassium ion exerted no measurable effect on the catalytic activity of the treated solids, in spite of decreasing the Brønsted acidity of Cs₁PW/SiO₂ and K₁PW/SiO₂ indicating that the acidity of HPW/SiO₂ decrease may be due to the interaction between HPW and the SiO₂ surface. On the other hand, significant decrease in the catalytic activity took place upon increasing the cation content (x) to x = 2, 2.5, and 3.     

Insight into the Mechanism of Hydrogenation of Amino Acids to Amino Alcohols Catalyzed by a Heterogeneous MoOx‐Modified Rh Catalyst

Hydrogenation of amino acids to amino alcohols is a promising utilization of natural amino acids. We found that MoO_x‐modified Rh/SiO₂ (Rh–MoO_x/SiO₂) is an efficient heterogeneous catalyst for the reaction at low temperature (323 K) and the addition of a small amount of MoO_x drastically increases the activity and selectivity. Here, we report the catalytic potential of Rh–MoO_x/SiO₂ and the results of kinetic and spectroscopic studies to elucidate the reaction mechanism of Rh–MoO_x/SiO₂ catalyzed hydrogenation of amino acids to amino alcohols. Rh–MoO_x/SiO₂ is superior to previously reported catalysts in terms of activity and substrate scope. This reaction proceeds by direct formation of an aldehyde intermediate from the carboxylic acid moiety, which is different from the reported reaction mechanism. This mechanism can be attributed to the reactive hydride species and substrate adsorption caused by MoO_x modification of Rh metal, which results in high activity, selectivity, and enantioselectivity.     

Effect of Mo content in MoO3/g-Al2O3 on the catalytic activity for transesterification of dimethyl oxalate with phenol

The influence of molybdenum content on the catalytic performance in the transesterification of dimethyl oxalate (DMO) with phenol to methyl phenyl oxalate (MPO) and diphenyl oxalate (DPO) was investigated. The results indicated that the MoO₃/Al₂O₃ catalyst with 14 wt% Mo content gave maximal DPO yield with 6.1% and 75.1% DMO conversion. The component, structure and phase of MoO₃/Al₂O₃ catalysts were characterized by means of X-ray diffraction (XRD), BET specific surface area, temperature-programmed desorption of ammonia (NH₃-TPD), and FTIR analysis of adsorbed pyridine. This revised version was published online in June 2006 with corrections to the Cover Date.     

Promoter effect of nickel in thiophene hydrodesulfurization as monitored by sulfur uptake and cyclohexane conversion

Hydrodesulfurization (HDS) activity and activation energy (ε′_TH) values were determined and compared with irreversible sulfur uptake (S_irr) by 5 Al₂O₃-supported (MoO_x, Ni and three NiMoO_x) catalysts and, in unsulfided form with the cyclohexane conversion activity. Synergy between Ni and Mo in catalytic activity and a correlation between HDS activity and the amounts of S_irr was found. Some explanations for the differences in catalytic behavior of the different samples are presented.     

Acetalization of glycerol using mesoporous MoO3/SiO2 solid acid catalyst

Acetalization of glycerol with various aldehydes has been carried out using mesoporous MoO₃/SiO₂ as a solid acid catalyst. A series of MoO₃/SiO₂ catalysts with varying MoO₃ loadings (1–20 mol%) were prepared by sol–gel technique using ethyl silicate-40 and ammonium heptamolybdate as silica and molybdenum source respectively. The sol–gel derived samples were calcined at 500 °C and characterized using various physicochemical characterization techniques. The XRD of the calcined samples showed the formation of amorphous phase up to 10 mol% MoO₃ loading and at higher loading of crystalline α-MoO₃ on amorphous silica support. TEM analyses of the materials showed the uniform distribution of MoO₃ nanoparticles on amorphous silica support. Raman spectroscopy showed the formation of silicomolybdic acid at low Mo loading and a mixture of α-MoO₃ and polymolybdate species at high Mo loadings. Moreover the Raman spectra of intermediate loading samples also suggest the presence of β-MoO₃. Acetalization of glycerol with benzaldehyde was carried out using series of MoO₃/SiO₂ catalysts with varying MoO₃ loadings (1–20 mol%). Among the series, MoO₃/SiO₂ with 20 mol% MoO₃ loadings was found to be the most active catalyst in acetalization under mild conditions. Maximum conversion of benzaldehyde (72%) was obtained in 8 h at 100 °C with 60% selectivity for the six-membered acetal using 20% MoO₃/SiO₂. Interestingly with substituted benzaldehydes under same reaction conditions the conversion of aldehydes decreased with increase in selectivity for six-membered acetals. These results indicate the potential of this catalyst for the acetalization of glycerol for an environmentally benign process.     

CrOx/SiO2催化剂上丙烷在CO2气氛中脱氢反应的研究

采用XRD、UV-vis DRS、ESR和微分吸附量热等技术,考察了铬担载量分别为2.5、5和10wt%的CrO_x/SiO₂催化剂的结构、表面性质和氧化还原性能。结果表明,催化剂表面上存在多种Cr的氧化态和聚集形式。随着Cr担载量从2.5wt%到10wt%的逐渐增大,催化剂表面占主导地位的Cr物种由CrO₃单体转为多聚CrO₃和Cr₂O₃晶相。在CO₂气氛中催化剂对丙烷转化率和丙烯选择性的大小顺序为2.5wt%CrO_x/SiO₂>5wt%CrO_x/SiO₂>10wt%CrO_x/SiO₂,反应过程中的原位ESR和UV-visDRS测定结果表明,催化剂表面的反应活性中心为Cr⁵⁺,Cr⁵⁺可由催化剂预处理过程中Cr³⁺的氧化及丙烷反应过程中CrO₃单体的还原产生,在反应中CO₂可使Cr³⁺重新氧化为Cr⁵⁺.     

Effect of the rhenium additive to VOx/TiO2 and MoOx/TiO2 catalysts on their properties in oxidative dehydrogenation of propane

VO_x/TiO₂ and MoO_x/TiO₂ catalysts with the addition of Re (Re/V or Mo = 0.5) were synthetized and tested in oxidative dehydrogenation of propane and in reduction by propane. XPS measurements showed depletion of the surface in Re. The Re additive does not affect the total conversion of propane, but increases the selectivity to propene. The effect is more pronounced for the MoO_x/TiO₂ catalyst. The increase in the selectivity to propene is accompanied with the increase in the reducibility of the catalysts.     

Transformation of n-hexane on Al2O3and SiO2supported Pt, Pt+Ga and Ir+Pt+Ga catalysts prepared by anchoring methods

Summary Transformation of n-hexane over Al₂O₃and SiO₂supported Pt, Pt+Ga and Ir+Pt+Ga catalysts was studied in a continuous-flow reactor operated under slug-pulse mode at 520°C. Bimetallic catalysts were prepared by introducing first Ga(OEt)₃and then diallylplatinum as precursor compounds. Iridium was then introduced viadecomposition of Ir₄(CO)₁₂adsorbed onto Pt+Ga catalysts. The addition of Ga to Pt/SiO₂catalyst decreased hydrogenation, aromatization and hydrogenolysis selectivity. Over Pt/Al₂O₃catalyst Ga increased hydrogenolysis selectivity and decreased isomerization and C₅-cyclization. The main effect of Ir was to increase hydrogenolysis selectivity and the stability of catalysts.</o:p>     

Platinum and molybdenum oxide deposited carbon electrocatalyst for oxidation of hydrogen containing carbon monoxide

Carbon-supported Pt/MoO_x catalysts for use in PEFC anodes were prepared and their catalytic activity for the oxidation of CO-contaminated H₂ was examined based on the fuel cell performance in PEFC single cell arrangements. Based on the XRD pattern and XPS measurements of the prepared Pt/MoO_x/C catalysts, it was found that the deposited MoO_x exists as an amorphous oxide phase. The MoO_x phase shows a redox peak at around 0.45 V, which was revealed by the cyclic voltammogram of the Pt/MoO_x/C in sulfuric acid solution. The PEFC performance of the cell with Pt/MoO_x/C was improved under 100 ppm CO-contaminated H₂ conditions compared to the Pt/C catalyst, and was almost comparable to the PtRu(1:1)/C catalyst.     

Encapsulated ultrafine and highly dispersed molybdenum dioxide nanoparticles in hollow mesoporous silica spheres as an efficient epoxidation catalyst for alkenes

A facile post-synthetic strategy was developed to functionalize the preformed hollow mesoporous silica spheres by encapsulating the molybdenum dioxide (MoO₂) nanoparticles inside the interior cavity. Hollow mesoporous silica spheres were prepared and employed as carriers, and the encapsulation of MoO₂ nanoparticles was achieved through a one-pot hydrothermal protocol. After characterization, the encapsulated MoO₂ nanoparticles were certified to be ultrafine and highly dispersed, which greatly promoted the catalytic activity. The as-prepared catalysts were utilized in epoxidation of alkenes and exhibited as a promising catalyst in this reaction. After reacting for 10 h, the optimal catalyst MoO₂@SiO₂-1 achieved a conversion above 95% and selectivity above 95%, respectively. Moreover, the catalysts also exhibited good reusability, conversion of 78% and selectivity of 89% (reaction time 4 h) were still obtained after recycling for 5 times. Meanwhile, the employed facial and efficient hydrothermal approach could be expanded to other molybdenum modified heterogeneous catalysts in various applications.     

Highly efficient mesoporous WO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/KIT-6 catalysts for oxidative desulfurization of dibenzothiophene with hydrogen peroxide

Oxidative desulfurization (ODS) of organic compounds containing sulfur element from a model oil was performed using tungsten oxide catalysts supported on mesoporous silica with cubic Ia3d mesostructure, well-defined mesopores (7.2 nm), high surface area (719 m²/g), and three-dimensional pore network (WO _x /KIT-6). The prepared WO _x /KIT-6 catalysts (5–20 wt% WO _x ) were characterized by X-ray diffraction analysis, N₂ sorption measurements, electron microscopy, H₂-temperature programmed reduction, Raman spectroscopy, and thermogravimetric analysis. Among the mesoporous catalysts, 10 wt% WO _x /KIT-6 exhibited the best catalytic performance. Sulfur-containing organic compounds, such as dibenzothiophene, 4,6-dimethyldibenzothiophene, and benzothiophene, were completely (100 %) removed from the model oil over 10 wt% WO _x /KIT-6 catalyst in 2 h. In addition, the catalyst could be reused several times with only slight decrease in catalytic activity.     

Application of Sol-Gel Method to Preparation of Ultra-Uniform Co-Based Catalysts for Fischer-Tropsch Reaction

Uniformly dispersed Co/SiO₂ catalysts (10–60 wt% on metal basis) were prepared by the sol-gel method, and used for the Fischer-Tropsch (F-T) synthesis in slurry phase at 503 K and 1 MPa in a flow of synthesis gas (H₂/CO = 2/1, W/F = 10 g-catal·h/mol). The catalysts were characterized by temperature-programmed reduction (TPR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and chemisorption. Although CO conversion over the unpromoted catalysts prepared by the sol-gel method was lower than the conventional catalysts prepared by impregnation, the catalytic activity of the former catalysts was more stable than the latter catalysts. The conversion was improved drastically, when 0.01–1 wt% of Ir or Ru (on metal basis) was added to the catalysts prepared by the sol-gel method. The TPR and XPS spectra and the H₂ chemisorption revealed that the noble metal addition was responsible for the reduction of Co particles in the catalysts. It is supposed that the durability of the promoted catalysts prepared by the sol-gel method was ascribed to the high dispersion of Co particles stabilized on the catalyst surface.     

Methanol-to-hydrocarbons conversion over MoO3/H-ZSM-5 catalysts prepared via lower temperature calcination: a route to tailor the distribution and evolution of promoter Mo species,and their corresponding catalytic properties

A series of MoO₃/H-ZSM-5 (Si/Al = 25) catalysts were prepared via calcination at a lower-than-usual temperature (400 °C) and subsequently evaluated in the methanol-to-hydrocarbon reaction at that same temperature. The catalytic properties of those catalysts were compared with the sample prepared at the more conventional, higher temperature of 500 °C. For the lower temperature preparations, molybdenum oxide was preferentially dispersed over the zeolite external surface, while only the higher loading level of MoO₃ (7.5 wt% or higher) led to observable inner migration of the Mo species into the zeolite channels, with concomitant partial loss of the zeolite Brønsted acidity. On the MoO₃ modified samples, the early-period gas yield, especially for valuable propylene and C₄ products, was noticeably accelerated, and is gradually converted into an enhanced liquid aromatic formation. The 7.5 wt% MoO₃/H-ZSM-5 sample prepared at 400 °C thereby achieved a balance between the zeolite surface dispersion of Mo species, their inner channel migration and the corresponding effect on the intrinsic Brønsted acidity of the acidic zeolite. That loading level also possessed the highest product selectivity (after 5 h reaction) to benzene, toluene and xylenes, as well as higher early-time valuable gas product yields in time-on-stream experiments. However, MoO₃ loading levels of 7.5 wt% and above also resulted in earlier catalyst deactivation by enhanced coke accumulation at, or near, the zeolite channel openings. Our research illustrates that the careful adoption of moderate/lower temperature dispersion processes for zeolite catalyst modification gives considerable potential for tailoring and optimizing the system''s catalytic performance.     

The influence of hydrogen-containing molybdenum and tungsten bronzes on the catalytic activity of palladium composite catalysts for the oxidation of H<Subscript>2</Subscript>, CO,and CH<Subscript>4</Subscript>

The influence of hydrogen-containing molybdenum and tungsten bronzes on the catalytic activity of palladium composite catalysts for the oxidation of H₂, CO, and CH₄ was studied. It was found that the composite catalysts containing H _x MO₃ phases (M = W or Mo), which were formed by the reduction of MoO₃ and WO₃ oxides with hydrogen in the presence of deposited Pd, showed higher catalytic activity in the oxidation of small molecules (H₂, CO, and CH₄) with excess oxygen than the traditional Pd/Al₂O₃ deposited catalyst with the same content of the deposited metal. It was shown that the thermal stability of the H _x MO₃ phases was the limiting factor influencing the activity of these composite catalysts.     

Activity of palladium sulfide catalysts in the reaction of gas-phase hydrogenation of 2-methylthiophene

In the interaction of hydrogen with 2-methylthiophene in the gas phase over palladium sulfide catalysts at 180–260?C and 0.1–0.8 MPa, the saturation of the thiophene ring resulting in 2-methylthiolane and the hydrogenolysis of 2-methylthiophene occurs. When the conversion is lower than 60%, these reactions occur independently; at higher conversions, methylthiolane also undergoes hydrogenolysis. The specific catalytic activity of PdS supported on γ-Al₂O₃, TiO₂, and carbon and without support is much lower in the hydrogenation of 2-methylthiophene than the activity of PdS supported on SiO₂, aluminosilicate, and zeolite HNaY having strong Brönsted acid surface sites.