Synthesis, characterization, and sorption properties of silica gel-immobilized Schiff base derivative

Silica gel was derivatized with benzophenone 4-aminobenzoylhydrazone (BAH), a Schiff base derivative, after silanization of silica by 3-chloropropyltrimethoxysilane (CPTS) by using a reported method. Characterization of the surface modification was confirmed through infrared spectroscopy, thermogravimetry, and elemental analysis. The immobilized surface was used for Cu(II), Ni(II), Zn(II), and Co(II) sorption from aqueous solutions. The influence of the amount of sorbent, ion concentration, pH, and temperature was investigated. The sorption data followed Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherms. The mean sorption energy (E) of benzophenone 4-aminobenzoylhydrazone (BAH) immobilization onto silica gel was calculated from D-R isotherms, indicating a chemical sorption mode for four cations. Thermodynamic parameters, i.e., DeltaG, DeltaS, and DeltaH, were also calculated for the system. From these parameters, DeltaH values were found to be endothermic: 27.0, 22.7, 32.6, and 34.6 kJ mol(-1) for Cu(II), Ni(II), Co(II), and Zn(II) metal ions, respectively. DeltaS values were calculated to be positive for the sorption of the same sequence of divalent cations onto sorbent. Negative DeltaG values indicated that the sorption process for these three metal ions onto immobilized silica gel is spontaneous.     

Adsorption of di-2-pyridyl ketone salicyloylhydrazone on silica gel: characteristics and isotherms

The adsorption of DPKSH onto silica gel was investigated, at 25±1 °C and pH 1, 4.7 and 12. For the same DPKSH concentration interval, the minimum required time of contact for adsorption maximum at pH 4.7 was smaller than at pH 1 and the maximum amount of DPKSH adsorbed per gram of silica at pH 1 is smaller than at pH 4.7. At pH 12 the DPKSH adsorption onto silica gel was not significant. The adsorption data followed Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherms. The maximum amount of solute adsorbed (m_ads^max) and the adsorption constant, K_L, were derived from Langmuir isotherm. The Freundlich constants 1/n and K_F related, respectively, to the energetic heterogeneity of adsorption sites and an empirical constant were evaluated. The mean sorption free energy (E) of DPKSH adsorption onto silica gel was calculated from D-R isotherm indicating a physical adsorption mode. Finally, conductimetric titrations showed the silica particle basicity and acidity as 0.002 and 0.3 mmol g⁻¹, respectively.     

Adsorption from binary solvent mixtures onto silica gel by HPLC frontal analysis

Summary The chromatographic technique of frontal analysis is applied to measuring adsorption from binary liquid mixtures by silica gel. The complete adsorption isotherm of a solvent mixture is obtained by measuring the break-through curves for a series of small concentration steps of the mobile phase. This method offers a direct way to determine the composition of the stationary phase in liquid-solid chromatography with mixed mobile phases. The surface excess isotherms of all binary systems formed by benzene, cyclohexane, and 1,2-dichloroethane, at the solution-silica gel interface at 25 °C are presented. The data of the three systems are shown to be thermodynamically mutually consistent.     

Thin-layer chromatography of 1,2,4-triazoles on silica gel

Summary The TLC behaviour of N-phenyl-1,2,4-triazoles and their derivatives on silica gel plates has been studied using simple solvents. Isomers were very well distinguished, resulting from different activities due to hydrogen bonding. A mixture of seven compounds has been resolved with diethylether-n-butylamine-pyridine (91.4:7.7:0.9).     

Synthesis and characterisation of morin-functionalised silica gel for the enrichment of some precious metal ions

Silica gel was firstly functionalised with aminopropyltrimethoxysilane obtaining the aminopropylsilica gel (APSG). The APSG was reacted subsequently with morin yielding morin-bonded silica gel (morin-APSG). The structure was investigated and confirmed by elemental and thermogravimetric analyses, IR and (13)C NMR spectral studies. Morin-APSG was found to be highly stable in common organic solvents, acidic medium (<2molL(-1) HCl, HNO(3)) or alkaline medium up to pH 8. The separation and preconcentration of Ag(I), Au(III), Pd(II), Pt(II) and Rh(III) from aqueous medium using morin-APSG was studied. The optimum pH values for the separation of Ag(I), Au(III), Pd(II), Pt(II) and Rh(III) on the sorbent are 5.7, 2.2, 3.7, 3.7 and 6.8, giving rise to separation efficiencies of 43.9, 85.9, 97.7, 60.9 and 91.0%, respectively, where the activity was found to be >90% in the presence of acetate ion. The ion sorption capacity of morin-APSG towards Cu(II) at pH 5.5 was found to be 0.249mmolg(-1) where the sorption capacities of Ag(I) and Pd(II) were 0.087 and 0.121mmolg(-1) and 0.222 and 0.241mmolg(-1) at pH 2.2 and 5.7, respectively. This indicates a 1:1 and 1:2 morin/metal ratios at pH 2.2 and 5.7, respectively. Complete elution of the sorbed metal ions was carried out using 10mL (0.5molL(-1) HCl+0.01molL(-1) thiourea) in case of Au(III), Pd(II), Pt(II) and Rh(III) and 10mL 0.5molL(-1) HNO(3) in case of Ag(I). Morin-APSG was successfully employed in the separation and preconcentration of the investigated precious metal ions from some spiking water samples yielding 100-folds concentration factor. The relative standard deviation (R.S.D.) and the T-test (|t|(1)) were calculated.     

Facile synthesis of an organic–inorganic nanocomposite,PEG–silica,by sol–gel method; its characterization and application as an efficient catalyst in regioselective nucleophilic ring opening of epoxides: Preparation of β-azido alcohols and β-cyanohydrins

The sol–gel method was used for the synthesis of a PEG–silica hybrid. In order to introduce PEG into the cavities of silica gel, first, the bis(3-trimethoxysilylpropyl)-polyethylene glycol precursor was synthesized by the reaction of 3-chloropropyltrimethoxysilane with alkoxides formed on the PEG terminals. The organic–inorganic hybrid silica was then synthesized by hydrolysis and polycondensation of the precursor under mild acidic conditions. The characteristics results of FT–IR, XRD and TGA confirmed the coexistence of silica and PEG networks. The catalytic ability of this heterogeneous catalyst to the regioselective ring opening of epoxides by azide and cyanide anions in H₂O was also investigated.     

Extraction of Pb(II), Cd(II), and Hg(II) from aqueous solution by nitrogen and thiol functionality grafted to silica gel measured by calorimetry

The reaction of ethylene sulfide with 3-aminopropyltrimethoxysilane gave a new silylating agent, which was anchored onto a silica surface via the sol–gel procedure. This surface displayed a chelating moiety containing nitrogen and two sulfur basic centers potentially capable of extracting cations from aqueous solutions. The process of metal extraction was followed by a batch method, and fitted to a modified Langmuir equation. The maximum adsorption capacities found were: 2.06 ± 0.01, 3.72 ± 0.02, and 5.14 ± 0.02 mmol g⁻¹ for Pb(II), Cd(II), and Hg(II), respectively. The enthalpies of bending are: −1.16 ± 0.04, −3.60 ± 0.10, and −8.94 ± 0.03 kJ mol⁻¹ for Cd(II), Pb(II), and Hg(II), respectively. The Gibbs free energies of binding agree with the spontaneity of the proposed reactions between cations and basic centers.     

Insight into copper-mordenite–silica mixtures (CuMOR–SiO2)

A series of ternary CuMOR–SiO₂ mixed materials were prepared by two synthesis approaches (CuMOR1–y–SiO₂ and CuMOR2–y–SiO₂). Extensive characterization was done for both series and some selected materials were tested in CO catalytic oxidation and NO reduction. The presence of CuMOR and SiO₂ segregated phases was observed in both series by XRD, suggesting that silica formation was not inhibited by the mordenite (MOR) presence. UV–Vis results exhibited that Cu ion exchange was successfully done for CuMOR1–y–SiO₂ series. In the CuMOR2–y–SiO₂ series, the amount of copper was below the sensitivity limit of EDS analysis. CuMOR1–50%–SiO₂ catalyst resulted with higher specific surface area and catalytic activity. A possible relation between reduction temperature, the increase in Cu plasmon excitation, and catalytic activity was observed.     

Synthesis and characterization of novel silica gel supported N-pyrazole ligand for selective elimination of Hg(II)

The polar organic molecule N-(2-hydroxyethyl)-3,5-dimethylpyrazole reacted with a 3-glycidoxypropyltrimethoxysilane silylant agent, previously anchored on a silica surface in a heterogeneous way to yield the product SiPz. The epoxide group was opened yielding chelating pendant group bonded to the inorganic surface. The product was characterized through elemental analysis, infrared spectroscopy, ¹³C NMR, surface area and thermogravimetry. The binding and adsorption abilities of SiPz was investigated for Hg²⁺, Cd²⁺, Pb²⁺, Cu²⁺, Zn²⁺, K⁺, Na⁺ and Li⁺ cations and compared to results of classical liquid-liquid extraction with the unbound N-pyrazole compound. The grafting at the surface of silica does not affect complexing properties of the ligand and the SiPz exhibits a high selectivity toward Hg²⁺ ion with no complexation being observed towards Zinc and alkali metals. The extracted and the complexing cation percentage were determined by atomic absorption measurements.     

Multilayer adsorption of alcohols from benzene/n-heptane mixtures on silica gel

An equation for multilayer adsorption from multicomponent liquid mixtures on solid surfaces¹ has been examined. For this purpose experimental adsorption data for four alcohols from benzene/n-heptane mixture on silica gel have been measured. Average number of the adsorbed layers, heterogeneity parameter and capacity of the surface phase have been evaluated by using the equation mentioned above.

---

Mehrschichten-Adsorption von Alkoholen aus Benzol/n-Heptan-Mischung an Silica Gel

Zusammenfassung Eine Gleichung für Mehrschichten-Adsorption an festen Oberflächen¹ aus Mehrkomponentenlösungen wurde getestet. Zu diesem Zweck wurden experimentelle Daten für die Adsorption von vier Alkoholen aus Benzol/n-Heptan-Mischung an Silica Gel herangezogen. Der Mittelwert für die Anzahl der Adsorptionsschichten, der Heterogenitätsparameter und die Kapazität der Oberflächenphase wurde aus dieser Gleichung berechnet.

     

Synthesis of bis(indolyl)methanes using silica gel as an efficient and recyclable surface

Here we describe a simple, clean, and efficient solvent-free protocol for the synthesis of bis(indolyl)methanes promoted by silica gel. The products were obtained in good to excellent yields through the reaction of indoles with cyclohexanone and a range of aldehydes. The silica gel was easily recovered and utilized for further reactions without loss of activity.     

Functionalization of silica gel by ultrasound-assisted surface Suzuki coupling

Mesoporous silica gel was functionalized by various organic functional groups using thiol-ene coupling of surface thiol groups with 4-vinylphenylboronic acid followed by Suzuki coupling with aromatic halides. For better performance, the synthesis was conducted under sonication. The presence of surface functional groups was confirmed by thermoanalysis, FT-IR spectroscopy and characteristic reactions of these groups. Solid-phase conditions of the synthesis eliminate the risk of side reactions of boronic acids.     

Chemoselective synthesis of quinoxalines and benzimidazoles by silica gel catalysis

Treatment of nitroolefins and o-phenylenediamine with silica gel catalyst produced quinoxalines mainly in THF, but gave benzimidazoles efficiently in water. Such a solvent-dependent chemoselective reaction has prominent features of affording two cyclized products selectively with the same substrate, short reaction time, operational simplicity, as well as available starting materials and nontoxic catalysts. In addition, the scope and limitations were explored and a plausible reaction mechanism is proposed.     

Study of silica gel and copper silicate gel solubilities in high performance liquid chromatography

Summary After summarizing published results on silica gel and alkyl-bonded silica gel solubilities, the experimental solubility of unmodified silica and copper silicate gel (used in ligand exchange chromatography) in watermethanol-ammonia and water-acetonitrile-ammonia mixtures are given. These results demonstrate that silica gel solubility, measured by a static method, varies greatly with the water volume fraction of a ternary mixture. Curiously, no influence from the organic nature of the solvent was demonstrated. This observation is inconsistent with the fact that the copper silicate gel used in ligand-exchange chromatography with water-methanol-ammonia as mobile phase is attacked more rapidly than with water-acetonitrile-ammonia.An explanation based upon the variations of acid-base properties of silicic acid versus mobile phase dielectric constant values in conjunction with the methanol protophilic properties is proposed. Finally, it is shown that chromatographic columns filled with copper silicate gel have lifetimes of several months, if they are used with a procolumn (of copper silicate gel) and with acetonitrile as organic solvent with a volume fraction greater than 0.5 in the mobile phase.     

Selective silica‐based sorbent materials synthesized by molecular imprinting for adsorption of pharmaceuticals in aqueous matrices

The presence of pharmaceuticals in aqueous environmental matrices often requires efficient and selective preconcentration procedures. Thus, silicas (SILs) were synthesized by a molecular imprinting technique using an acid‐catalyzed sol‐gel process and the following drugs as templates: fluoxetine, gentamicin, lidocaine, morphine, nifedipine, paracetamol, and tetracycline. The materials were subjected to sorbent extraction assisted by ultrasonic treatment to remove the drugs and the consequent formation of molecular imprinted cavities. The surface area of the resulting materials ranged from 290 to 960 m²/g. Adsorption tests were performed with the molecular imprinting phases. In terms of the potential selectivity, the SILs were subjected to the adsorption of drugs from samples such as potable and surface water. The adsorption capacity remained in the range between 55 and 65% for both matrices, while for the nonimprinted SIL it remained between 15 and 20%.     

Synthesis of acrylic-modified sol–gel silica

Silica was obtained by sol–gel process through hydrolysis and condensation of tetraethyl orthosilicate (TEOS) using molar fraction of H₂O/TEOS=9 under alkaline catalysis, at different reaction times (5 min to 24 h). At the end of each time, the reaction medium appeared as a suspended microparticle system. After solvent evaporation, the yield was calculated to be around 100% and practically independent of the time of reaction. The silica had its surface modified through the condensation reaction with acryloyl chloride forming organically modified silica. The unmodified and modified silica were characterized by thermogravimetry and derivative thermogravimetry (TG/DTG), infrared spectrometry (FT-IR), size particle and optical microscopy (OM). The acrylic content was independent of the reaction time. The methodology represents an alternative route to obtain silica with an unsaturated organic group, able to polymerize and stabilize up to 300–400°C. The modified material has a potential application as compatibilizing filler in dental composite.     

超快速溶胶-凝胶法制备高纯二氧化硅单块

传统的溶胶-凝胶工艺存在几个严重的缺点,例如,凝胶时间过长(20d以上),体积收缩太大(>75%),形状和尺寸无法控制以及严重的龟裂等^[1].这些缺点限制了它在技术上的应用.     

Sorption of the peroxocomplex of titanium on silica gel and its analytical use

Summary Sorption of the titanium peroxocomplex on silica gel was studied in dependence on the pH and on the presence of various complexing substances, especially tartaric and citric acids. The distribution coefficients for the titanium peroxocomplex and for some other components were determined. Optimum conditions were established for the separation of small amounts of titanium from a number of accompanying cations and anions on a column and under static conditions.     

Synthesis and characterization of TiO2 powders by the double-nozzle electrospray pyrolysis method. Part 2. Material evaluation

Here we report the synthesis and characterization of anatase TiO₂ powders by the double-nozzle electrospray pyrolysis method. Titanium(IV) bis(ammonium lactato) dihydroxide (TALH) aqueous solution (2.0 wt%) and pure H₂O were separately injected into capillaries by using two syringe pumps, and were electrosprayed by using positive (+4 kV) and negative (−4 kV) DC voltage, respectively. Under a stream of dry clean air, the droplets were carried to the stainless steel tube heated with a tubular furnace at 350–450 °C. Thanks to the neutralization of droplets by the double-nozzle electrospray, the final TiO₂ powder yield after pyrolysis was much improved from 6% (by single nozzle) to 55.4% (in this study), although the particle size distribution became wider due to the electrical neutralization and coalescence of the droplets. Photocatalytic activity for H₂ evolution was studied.     

Silica gel ethyleneimine and its adsorption capacity for divalent Pb, Cd, and Hg

Activated silica gel was directly modified with a cyclic molecule, ethyleneimine, yielding a surface with various nitrogen basic centers, ≡Sil–O(CH₂CH₂NH)_nCH₂CH₂NH₂. Infrared spectroscopy, ¹³C NMR, thermal, and elemental analyses confirmed the covalent attachment of the organic species onto the silica matrix. The purpose of this paper is to describe the interaction involving the grafted species on silica surface with the divalent heavy cations, Pb(II), Cd(II), and Hg(II), from aqueous solutions at room temperature. The process of metal extraction was followed by the batch method and the order of the maximum extraction capacities found was: 1.27 ± 0.04, 1.02 ± 0.02, and 0.98 ± 0.01 mmol g⁻¹ for Pb(II), Cd(II), and Hg(II) chlorides, respectively. These interactions were followed by calorimetric titration. The enthalpies of these processes are: −3.05 ± 0.02, −1.09 ± 0.01, and −9.88 ± 0.03 kJ mol⁻¹ for Pb(II), Cd(II), and Hg(II), respectively. The standard molar Gibbs free energies are in agreement with the spontaneity of the proposed reactions between cation and basic center.