Studies on the Phase Properties of Winsor Ⅰ-Ⅲ Type Microemulsions with Dielectric Relaxation Spectroscopy

The dielectric relaxation spectroscopy （DRS） of Winsor I -Ⅲ microemulsions for nonionic surfactant octyl polyglucoside CsG1.46/1-butanol/cyclohexanedwater system was studied. The experiment shows that the permittivity decreases with the increase in the frequency and clear dielectric relaxation phenomena were observed. Permittivity obviously decreases with the change of the microstructure of the microemulsion, W/O, B.C. and O/W can be distinguished by the permittivity.     

Studies on Phase Behavior of Alkyl Polyglucoside Based on Microemulsions with Modified Fishlike Phase Diagram

The three-phase behavior in the quaternary system of an alkyl (C8/10^- or C12/14^-)polyglucoside / 1-butanol / n-octane / water has been studied at 40℃ with the modified fishlike phase diagram, which is presented by us for the first time. The mass fraction of 1-butanol in the hydrophile-lipophile balanced interfacial layer, A^S, the coordinates of the start point B and the end point E of the phase diagram, and the solubilities of alkyl polyglucoside and 1-butanol in n-octane phase were calculated. The solubilization of the microemulsion was also discussed.     

Study on the Phase Behavior of Supercritical CO2／Dynol—604／Water System and Solubilization of Methyl Orange in the Microemulsions

It was found that Dynol-604, a non-fluorous and no silicon-containing nonionic surfactant,was soluble in supercritical (SC) CO2. The phase behavior of SC CO2/Dynol-604/water system was studies. The results showed that one-phase water-in-CO2 microemulsions could be fromed. The solubilization of methyl orange in the microemulsions proved further the existence of water domain in the microemulsions.     

Vapor-phase synthesis of N-butylaniline from aniline and 1-butanol over Cu/SiO2 catalyst

The Cu/SiO2 catalyst prepared by incipient wetness method exhibited very high activity and selectivity for the vapor-phase synthesis of N-butylaniline from aniline and 1-butanol. When Cu loading was 0.70 mmol/g-SiO2 and the catalyst precursor was calcined at 500 ℃, 1-butanol conversion reached 99%, and the selectivity of N-butylaniline exceeded 97%.     

Phase Structures of Microemulsions Determined by the Steady-State Fluorescence Method

Experimental The pyrene was purchased from Sigma Co., and the other chemicals were of A. R. grade. Water was deionized and distilled twice before use. The microemulsions of required compositions were prepared in the following way. The stock microemulsions were made without water at first, corresponding to the A point (10wt% octane, 63wt% n-butanol, 27wt% CTAB) in the phase diagram of Figure 1 and then a series of microemulsions were made along AW dilution line with adding water. Calcu…     

Effect of Mn（Ⅱ） and Ce（Ⅳ） Ions on the Oxidation of Lactic Acid by Chromic Acid

The kinetics and mechanism of lactic acid oxidation in the presence of Mn（Ⅱ） and Ce（Ⅳ） ions by chromic acid were studied spectrophotometrically. The oxidation of lactic acid by Cr（Ⅵ） was found to proceed in two measurable steps, both of which gave pyruvic acid as the primary product in the absence of Mn（Ⅱ）.2Cr（Ⅵ）＋2CH3CHOHCOOH→2CH3COCOOH＋Cr（Ⅴ）＋C（Ⅲ） Cr（V）＋CH3CHOHCOOH→Cr（Ⅲ）＋CH3COCOOHThe observed kinetics was explained due to the catalytic and inhibitory effects of Mn（Ⅱ） and Ce（Ⅳ） on the lactic acid oxidation by Cr（Ⅵ）. The reactivity of lactic acid depends upon the experimental conditions. It acts as a two- or three- equivalent reducing agent in the absence or presence of Mn（Ⅱ）. It was examined that Cr（Ⅲ） products resulting from the direct reduction of Cr（Ⅵ） by three-equivalent reducing agents. The oxidation of lactic acid follows the complex order kinetics with respect to [lactic acid]. The activation parameters Eo, △H^#, and AS^# were calculated and discussed.     

Enantiomer Separation of α—Dimethyl Dicarboxylate Biphenyl and Related Biphenyl Compounds by Normal Phase HPLC on Polysaccharide Based Chiral Stationary Phases

Cellulose tris(4-methylphenylcarbamate),amylose tris(3,5-dimethylphenylcarbamate) and amylose tris (phenylcarbamate) were prepared by the method reported by Okamoto and were coated onto an aminopropylated mesoporous spherical silica gel.These final products were used as chiral stationary phases of high performance liquid chromatography for the eighteen structurally related biphenyl compounds.The resolution was made using normal-phase methodology with a mobile phase consisting of n-hexane-alcohol(ethanol,1-propanol,2-propanol or 1-butanol).The effects of various aliphatic alcohols in the mobile phase were studied.The structural features of the solutes that influence their k′ were discussed.A dominant effects of trifluoroacetic acid on chiral separation of acidic solutes was noted.     

Selective Oxidation of Propane over CsFePVAsMo Heteropoly Compound Catalyst

Both the partially reduced and non-reduced multi-component heteropoly compound catalysts with Keggin structure were prepared and used for the selective oxidation of propane. The catalysts were characterized by IR, H2-TPR, NH3-TPD, SEM and XRD. The addition of Cs increased the selectivity of acrylic acid and acetic acid. The selective oxidation performance was greatly improved with the addition of As. Among all of the tested catalysts, the catalytic performance of the Cs1.8Fe0.16HxPVAs0.4Mo11O40 (non-reduced) was the best and the maximum yield of acrylic acid reached 16.42%.     

Catalytic Combustion of Methane over High Copper-Loading ZSM-5 Catalysts

Two series of Cu/ZSM-5 catalysts,loading from 5 to 20 wt% CuO,were prepared by the deposition-precipitation and impregnation methods,respectively.The catalysts prepared by the impreg- nation method showed better catalytic performances than those prepared by the deposition-precipitation method and the increase of copper loading favored methane conversion.20Cu(I)/ZSM-5 had the highest activity with T_(90%)of 746 K,and for 20Cu(D)/ZSM-5,T_(90%)was as high as 804 K.The characteriza- tion of X-ray diffraction(XRD),temperature-programmed reduction(TPR),temperature-programmed desorption(TPD),and X-ray photoelectron spectroscopy(XPS)revealed that the dispersion of cop- per species could be improved by using the deposition-precipitation method instead of the impregnation method,but the fraction of surface CuO,corresponding to active sites for methane oxidation,was larger on 20Cu(I)/ZSM-5 than 20Cu(D)/ZSM-5.The results of Pyridine-Fourier transform infrared spectrum (Py-FT-IR)showed that a majority of Lewis acidity and a minority of Brφnsted acidity were present on Cu/ZSM-5 catalysts.20Cu(I)/ZSM-5 presented more Lewis acid sites.The number of Lewis acid sites changed significantly with preadsorption of oxygen.Adsorption of methane and oxygen on acid sites was observed.The properties of Cu/ZSM-5 catalysts were correlated with the activity for methane oxidation.     

Synthesis and Characterization of a Novel Liquid Crystalline Chitin — Quaternary Ammonium Chitosan Salt

N-Butyl chitosan(NBCS) derivatives were prepared by introducing butyl groups into the amine groups of chitosan via Schiff base intermediates. The quaternization of NBCS was carried out by using ethyl iodide to produce water-soluble cationic polyelectrolytes. The degree of the substitution of the products was measured by means of the electron spectroscopy for a successful chemical analysis. The quaternary ammonium chitosan salt(QACS) was proved to be a novel cholesteric liquid crystalline chitin, by means of the polarized optical microscopy and the circular dichroism spectropolarimetry. The critical mass fraction of the QACS/formic acid solution forming a lyotropic liquid crystal phase was 50%, which was almost the same as that of the NBCS/formic acid solution, but much hiuher than that of the chitosan in the same solvent.     

Electrochemical Behavior of Anthraquinone in Reverse Micelles and Microemulsions of Cetyltrimethylammonium Bromide

The electrochemical behavior of an anthraquinone (AQ) was studied in aqueous solutions at a glassy carbon electrode, using the sodium salt of anthraquinone-2-sulfonic acid (AQS), by employing cyclic voltammetry. AQ undergoes a two-electron reduction in aqueous media. The electrochemical behavior of AQ was also investigated in micelles, reverse micelles (CTAB/1-butanol/water), and microemulsions (CTAB/1-butanol/water/cyclohexane) of cetyltrimethylammonium bromide (CTAB). The electrode reactions of AQ in reverse micelles and microemulsions are nearly reversible at low oil (cyclohexane) content. However, at higher oil content, the reversibility is gradually lost. In the case of reverse micelles, the reduction current, as well as the reduction potential, of AQ depend on the transition from a micellar solution to a stable solution of reverse micelles that occurs with added 1-butanol. In microemulsions, the change in cyclohexane content was found to cause a linear increase in the peak current for AQ reduction as well as a linear decrease in the corresponding reduction potential. As the cyclohexane content is increased, the o/w microemulsions dominated by micelles undergo a transition to a w/o microemulsion dominated by reverse micelles, which causes changes in the electrochemical behavior.     

Influence of the Structure of Cetyltrimethylammonium Bromide Based Microemulsions on Base Hydrolysis of Carboxylic Acid Esters

The structure of water/cetyltrimethylammonium bromide/n-butanol/hexane microemulsions was studied by conductometry, viscometry, and Fourier transform ¹H NMR spectroscopy with pulse magnetic field gradient. The regions of phase inversion from inverse micelles in hexane through a bicontinual structure to a dispersion of normal micelles in water were determined. The influence of the structure of the microemulsions on the rate of hydrolysis of carboxylic acid p-nitrophenyl esters was analyzed. The hydrolysis rate constants considerably increase in going from inverse to normal microemulsions.     

New catanionic surfactants, phase stability and synthesis of ultrafine CdS nanoparticles

A systematic study on the water-intake capacity of the microemulsion formed using a catanionic surfactant (synthesized by taking equimolar mixture of acid and amine) with varying hydrocarbon chain length of the acid has been carried out. A decrease in the water-intake capacity with increase in the chain length was observed. Shorter chain length of co-surfactant (1-butanol compared to 1-octanol) led to higher water-intake capacity of microemulsions which may also be attributed to the high hydrophilic-lipophilic balance (HLB) of 1-butanol. Three new microemulsions based on catanionic surfactants have been used to synthesize quantum dots of CdS. The size of CdS quantum dots decreased with increase in chain length of the acid component of the catanionic surfactant.     

Comparison of microstructures of microemulsion and swollen micelle in electrokinetic chromatography

Recently, 1-butanol modified MEKC was proven to be similar to MEEKC in separation performance. In the present work, typical microemulsion containing 0.8% n-octane/3.3% SDS/6.6% 1-butanol/20 mM borax buffer and corresponding swollen micelle without n-octane were used to compare their microdroplet structures including hydrodynamic radius, electrokinetic potential ζ and charge density at the hydrodynamic shear surface, as well as microenvironment polarity in the interior of the microdroplets. Three kinds of corticosteroids were separated with MEEKC and 1-butanol modified MEKC to assess their separation performances. The experiment results showed that both microstructure and separation performance in microemulsion and in swollen micelle systems were alike, no matter whether oil phase n-octane was present. The environment polarity in the core of swollen micelle was slightly higher than in the microemulsions, and both of them were higher than in n-octane medium. Furthermore, the influences of SDS and 1-butanol concentration on microstructures were measured in details. Increasing the amount of SDS, hydrodynamic radius decreased in microemulsion but increased in swollen micelle. On the contrary, ζ and shear surface charge density changed in the reverse trends. With increment of 1-butanol concentration, the hydrodynamic radius increased dramatically in microemulsions, whereas decreased slightly in swollen micelle. Even though using n-octane as oil core was not a key factor, microemulsions and swollen micelle as pseudostationary phase in EKC should not be exactly the same.     

微乳液中单分散银纳米颗粒的制备及抗磨性能

采用水/液体石蜡/Span 80-Tween 80/正丁醇微乳液体系, 制备了具有良好单分散性的Ag纳米颗粒. 通过X射线粉末衍射仪、透射电子显微镜、傅立叶变换红外光谱仪和热分析仪表征了Ag纳米颗粒的结构、形貌、粒径大小及分布、表面键合性质和热性能. 结果表明, 所制备的Ag纳米颗粒具有立方晶型结构, m(Span 80)∶m(Tween 80)=7∶3时, 粒径分布呈单分散性, 平均粒径约为6 nm. 在四球长时抗磨损试验机上考察了分散于液体石蜡中Ag纳米颗粒的抗磨性能. 实验结果表明, Ag纳米颗粒具有良好的抗磨性, 且能显著提高基础油的承载能力.     

Effect of the structures of microemulsions on chemical reactions

Two kinds of chemical reactions were studied in two different microemulsion systems: cetyltrimethylammonium bromide/1-butanol/10 and 25% n-octane/water and sodium dodecyl sulfonate/1-butanol/20% styrene/water. One reaction is a hydrolysis reaction, in which aspirin and 2,4-dinitrochlorobenzene were used as the hydrolysis substrates. The second reaction is the polymerization of styrene, which was initiated by using two initiators, water-soluble K₂S₂O₈ and oil-soluble 2,2′-azobis(isobutyronitrile), and, at the same time, the polymerization of acrylamide, which was initiated by NaHSO₃, was also studied. All the hydrolysis reaction experimental results show that the hydrolysis is greatly affected by the structures and the structural transitions of microemulsions. The hydrolysis rates are higher in water-in-oil (W/O) microemulsion media and decrease with the addition of water. The rates increase in bicontinuous (BC) microemulsions and decrease in oil-in-water (O/W) microemulsions. The transition points of the hydrolysis rates occurred at the two microemulsion structural transition points from W/O to BC and from BC to O/W. The polymerization relationships between the conversions of styrene, the molecular weights of polystyrene and the water contents of the microemulsion system were obtained. The effects of microemulsion structures on the sizes of the polystyrene particles and on the molecular weights of the polymers are discussed. Polystyrene particles with diameters of 10–60 nm were observed by microscopy. Our experimental polymerization results show that microemulsions are suitable as media for the production of polymers, the molecular weights and the particle sizes of which can be controlled and predicted by variations in microemulsion structures. Received: 11 July 1999/Accepted: 26 July 1999     

Formamide,a water substitute XIV (1) waterless microemulsions 8. Structural analysis by X-ray scattering of CTAB aggregates in formamide and in the microemulsion system (formamide,CTAB, isooctane, 1-butanol)

X-ray scattering was used to analyse the structures of aggregates of CTAB in various formamide-containing media.Firstly, CTAB micelles were detected in formamide solutions. A spherical micelle model was proposed; at values close to the CMC, smaller micelles were observed in formamide than in water.Secondly, the structure of microemulsions in the isooctane-rich zone of the system (formamide/CTAB=2, isooctane, 1-butanol) was studied by X-ray scattering. The structure was found to be quite different in this zone from that normally observed in aqueous microemulsions. Structures compatible with small filaments of formamide were detected. The results were related to previous measurements of electrical conductivity.     

Studies on the Phase Properties of Winsor Ⅰ-Ⅲ Type Microemulsions with Dielectric Relaxation Spectroscopy

The dielectric relaxation spectroscopy (DRS) of Winsor Ⅰ～Ⅲ microemulsions for nonionic surfactant octyl polyglucoside C8G1.46/1-butanol/cyclohexane/water system was studied.The experiment shows that the permittivity decreases with the increase in the frequency and clear dielectric relaxation phenomena were observed. Permittivity obviously decreases with the change of the microstructure of the microemulsion, W/O, B.C. and O/W can be distinguished by the permittivity.     

Displacement of hexanol by the hexanoic acid overoxidation product in alcohol oxidation on a model supported palladium nanoparticle catalyst

This work characterizes the adsorption, structure, and binding mechanism of oxygenated organic species from cyclohexane solution at the liquid/solid interface of optically flat alumina-supported palladium nanoparticle surfaces prepared by atomic layer deposition (ALD). The surface-specific nonlinear optical vibrational spectroscopy, sum-frequency generation (SFG), was used as a probe for adsorption and interfacial molecular structure. 1-Hexanoic acid is an overoxidation product and possible catalyst poison for the aerobic heterogeneous oxidation of 1-hexanol at the liquid/solid interface of Pd/Al(2)O(3) catalysts. Single component and competitive adsorption experiments show that 1-hexanoic acid adsorbs to both ALD-prepared alumina surfaces and alumina surfaces with palladium nanoparticles, that were also prepared by ALD, more strongly than does 1-hexanol. Furthermore, 1-hexanoic acid adsorbs with conformational order on ALD-prepared alumina surfaces, but on surfaces with palladium particles the adsorbates exhibit relative disorder at low surface coverage and become more ordered, on average, at higher surface coverage. Although significant differences in binding constant were not observed between surfaces with and without palladium nanoparticles, the palladium particles play an apparent role in controlling adsorbate structures. The disordered adsorption of 1-hexanoic acid most likely occurs on the alumina support, and probably results from modification of binding sites on the alumina, adjacent to the particles. In addition to providing insight on the possibility of catalyst poisoning by the overoxidation product and characterizing changes in its structure that result in only small adsorption energy changes, this work represents a step toward using surface science techniques that bridge the complexity gap between fundamental studies and realistic catalyst models.     

Influence of CTAB/alkanol/cyclohexane w/o microemulsions on the basic hydrolysis of crystal violet

The basic hydrolysis of crystal violet has been studied in w/o microemulsions of the CTAB/alkanols/cyclohexane system (alkanols: 1-butanol and 1-hexanol). The reaction can be considered to occur in the water phase of the droplets and from the rate constant the apparent dielectric constant of the water phase was determined. The cyclohexane incorporation in the system produces a decrease in the effective dielectric constant of the water phase and in the specific conductivity.