缓冲层对InSb/GaAs薄膜质量的影响

InSb是制作3~5μm红外探测器的重要材料。在GaAs衬底上外延生长InSb,存在的主要问题在于两种材料间14.6%的晶格失配度,会引入较大的表面粗糙度以及位错密度,使外延材料的结构和电学性能均会受到不同程度的影响。通过系列实验,研究了在生长过程中缓冲层对薄膜质量的影响。利用高能电子衍射仪(RHHEED)得到了合适的生长速率和Ⅴ/Ⅲ比,研究了异质外延InSb薄膜生长中低温InSb缓冲层对材料生长质量以及不同外延厚度对材料电学性质的影响。采用原子力显微镜(AFM)、透射电子显微镜(TEM)、X射线双晶衍射(DCXRD)等方法研究了InSb/GaAs薄膜的表面形貌、界面特性以及结晶质量。通过生长合适厚度的缓冲层,获得了室温下DCXRD半高峰宽为172″,77 K下迁移率为64300 cm²·V^-1·s^-1的InSb外延层。     

基于MOCVD三步生长的GaAs/Si外延技术EI北大核心CSCD

在硅(Si)上外延生长高质量的砷化镓(GaAs)薄膜是实现硅基光源单片集成的关键因素。但是,Si材料与GaAs材料之间较大的晶格失配、热失配等问题对获得高质量的GaAs薄膜造成了严重影响。本文利用金属有机化学气相沉积(MOCVD)技术开展Si基GaAs生长研究。通过采用三步生长法,运用低温成核层、高温GaAs层与循环热退火等结合的方式,进一步降低Si基GaAs材料的表面粗糙度和穿透位错密度。并利用X射线衍射(XRD)ω-2θ扫描追踪采用不同方法生长的样品中残余应力的变化。最终,在GaAs低温成核层生长时间62 min(生长厚度约25 nm)时,采用三步生长、循环热退火等结合的方式获得GaAs(004)XRD摇摆曲线峰值半高宽(FWHM)为401″、缺陷密度为6.8×10^(7) cm^(-2)、5μm×5μm区域表面粗糙度为6.71 nm的GaAs外延材料,在材料中表现出张应力。     

Si缓冲层的生长温度对SiGe组分、结构的影响

利用同步辐射X射线高分辨衍射、掠入射表面衍射、原子力显微镜、电子显微镜等手段研究了SiGe外延层的生长质量、组分与作为缓冲层Si的生长温度之间的关系. 研究表明, 在外延薄膜中Ge的含量为32±2%; 当Si缓冲层生长温度在400—500\textcelsius范围内, SiGe外延层质量高, 没有生长位错出现. X射线反射及原子力显微镜则显示对应最光滑的SiGe外延层表面的Si缓冲层的生长温度为450\textcelsius, 相应的表面粗糙度仅为大约15\AA.     

LP-MOCVD两步生长法制备的InAs0.9Sb0.1/GaAs

利用LP-MOCVD技术,采用两步生长法,在(100)GaAs单晶衬底上生长高质量的InAs0.9Sb0.1。用扫描电镜、X射线单晶衍射、Hall测量以及Raman光谱等方法对材料进行了表征。分析了缓冲层和外延层生长温度对外延层表面形貌的影响。获得了表面光亮,室温载流子浓度为1.9×1017cm-3和迁移率为6214cm2/V.s的InAs0.9Sb0.1。在室温Raman光谱中观察到InAs0.9Sb0.1中InAs(LO)的233cm-1和InSb(LO)的187cm-1两种光学声子行为。     

AlN插入层对硅衬底GaN薄膜生长的影响

利用金属有机化合物气相外延沉积技术在2inch(5.08cm)Si(111)图形衬底上生长了GaN外延薄膜,在Al组分渐变AlGaN缓冲层与GaN成核层之间引入了AlN插入层,研究了AlN插入层对GaN薄膜生长的影响。结果表明,随着AlN插入层厚度的增加,GaN外延膜(002)面与(102)面X射线衍射摇摆曲线半峰全宽明显变小,晶体质量变好,同时外延膜在放置过程中所产生的裂纹密度逐渐减小直至不产生裂纹。原因在于AlN插入层的厚度对GaN成核层的生长模式有明显影响,较厚的AlN插入层使GaN成核层倾向于岛状生长,造成后续生长的nGaN外延膜具有更多的侧向外延成分,从而降低了GaN外延膜中的位错密度,减少了GaN外延膜中的残余张应力。同时还提出了一种利用荧光显微镜观察黄带发光形貌来表征GaN成核层形貌和生长模式的新方法。     

热应力作用降低LPE层中的位错

提出由温差造成热剪切应力,引起衬底穿线位错滑移,形成<110>界面位错,从而降低LPE层中位错的模型。稳定自然对流下的温度梯度液相外延,存在衬底厚度方向的温差,能在边缘固定的衬底中造成热剪切应力。生长了厚GaAs和Ga_1-xAl_xAs层(x<0.3),估算的热剪切应力大于产生<110>暗线缺陷的临界剪切应力。表面腐蚀坑观察表明,外延层位错密度下降,或无位错。界面蚀槽和阴极荧光观察表明,衬底穿线位错在界面弯曲成<110>界面位错。透射电子显微镜观察表明,界面位错多 关键词：     

分子束外延GaAs/Si材料的喇曼散射研究

对逐层腐蚀的GaAs/Si材料进行喇曼散射实验,研究晶格振动声子谱沿外延生长方向的剖面分布,发现GaAs外延层从表面到界面经历着从双轴张应力到双轴压应力的变化。用Anastassakis等人提出的特殊相关模型对GaAsLO声子的谱形进行分析,发现GaAs外延层的晶体质量随着外延层厚度的减薄(从1μm—500?)是渐渐退化的,这是由于界面失配位错进入外延层所致。对GaAs LO声子与TO声子强度之比分析表明:外延层厚度从3.3μm变化到1μm左右时,其晶体质量并不是简单地随着厚度的减薄而退化,在1.3μm左右外延层晶体质量反而变好。对这种现象做了详细的讨论。 关键词：     

GaAs(001)表面外延生长Mn薄膜的XPS研究

利用x射线光电子能谱的深度剖面技术,对不同衬底温度下分子束外延生长的Mn薄膜及其与GaAs(001)衬底间的界面进行了元素组分和化学结合状态随深度变化的研究。实验发现衬底温度等于400K时制备的fcc-Mn/GaAs(001)体系中,fcc-Mn层与GaAs衬底之间存在一层较厚的Mn-Ga-As的缓冲层;衬底温度等于300K(室温)时制备的a-Mn/GaAs(001)体系中也存在类似的缓冲层,但它的厚度与fcc-Mn的情形相比要小得多;而当衬底温度等于450K时制备的体系在GaAs衬底之上全部是Mn-Ga     

生长速率对低压MOCVD外延生长GaAs/Ge异质结的影响

采用自制的液相金属氧化物化学汽相沉积(LP-MOCVD)设备,在Ge(100)向(110)面偏9°外延生长出GaAs单晶外延层,对电池材料进行了X射线衍射测试分析,半峰宽为52″.讨论了外延生长参量对GaAs/Ge的影响,表明抑制反向畴不仅与过渡层有关,而且与GaAs单晶外延生长参量有关.适当的生长速率可有效地抑制反向畴的生长.     

关于RHEED振荡技术优化GaAs(110)量子阱生长的研究

在GaAs(110)衬底上生长的半导体材料有诸多优良性能，使得在非极性GaAs(110)衬底上获得高质量各类异质结材料，成为近年来分子束外延生长关注的课题.考虑GaAs(110)表面是Ga和As共面，最佳生长温度窗口很小；反射式高能电子衍射的(1×1)再构图案对生长温度和V/Ⅲ束流比不敏感，难于通过观察再构图案的变化，准确地找到最佳生长条件.作者在制备GaAs(110)量子阱过程中，观察到反射式高能电子衍射强度振荡呈现出的单双周期变化.这意味着不同工艺条件下，在 GaAs(110)衬底上量子阱有单层和双层两种生长模式.透射电子显微镜和室温光致荧光光谱测量结果表明：在双层生长模式下量子阱样品光学性能较差，而在单层生长模式下量子阱光学性能较好，但是界面会变粗糙.利用这一特点，我们采用反射式高能电子衍射强度振荡技术，找到了一种在GaAs(110)衬底上生长高质量量子阱的可行方法. 关键词： 反射高能电子衍射 量子阱 分子束外延     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.