Temperature-dependent competition between adsorption and aggregation of a cellulose ether--simultaneous use of optical and acoustical techniques for investigating surface properties

Adsorption of the temperature-responsive polymer hydroxypropylmethylcellulose (HPMC) from an aqueous solution onto hydrophobized silica was followed well above the bulk instability temperature (T(2)) in temperature cycle experiments. Two complementary techniques, QCM-D and ellipsometry, were utilized simultaneously to probe the same substrate immersed in polymer solution. The interfacial processes were correlated with changes in polymer aggregation and viscosity of polymer solutions, as monitored by light scattering and rheological measurements. The simultaneous use of ellipsometry and QCM-D, and the possibility to follow layer properties up to 80 °C, well above the T(2) temperature, are both novel developments. A moderate increase in adsorbed amount with temperature was found below T(2), whereas a significant increase in the adsorbed mass and changes in layer properties were observed around the T(2) temperature where the bulk viscosity increases significantly. Thus, there is a clear correlation between transition temperatures in the adsorbed layer and in bulk solution, and we discuss this in relation to a newly proposed model that considers competition between aggregation and adsorption/deposition. A much larger temperature response above the T(2) temperature was found for adsorbed layers of HPMC than for layers of methyl cellulose. Possible reasons for this are discussed.     

Temperature responsive flocculation and solid-liquid separations with charged random copolymers of poly(N-isopropyl acrylamide)

Temperature-responsive random copolymers based on poly(N-isopropyl acrylamide) (PNIPAM) with 15 mol% of either acrylic acid or dimethylaminoethyl acrylate quaternary chloride were prepared. The effect of the charge and its sign were investigated in the solid-liquid separation of silica and alumina mineral suspensions. The results were compared to PNIPAM homopolymer of similar molecular weight. PNIPAM copolymers of the same charge as the particles (co-ionic PNIPAM) act as dispersants at both 25°C and 50°C. Flocculation occurs when counter-ionic PNIPAM facilitates selective aggregation and rapid sedimentation of minerals at both 25°C and 50°C. Adsorption and desorption studies showed that, unlike non-ionic PNIPAM, little desorption of the counter-ionic copolymers from the oxides occurred after cooling a suspension from 50°C to below the lower critical solution temperature. Thus, incorporation of counter-ionic charge into the temperature sensitive polymer PNIPAM was found to reduce the sediment bed consolidation upon cooling when compared to PNIPAM homopolymers. The lack of secondary consolidation upon cooling is attributed to attractive inter-particle forces, such as conventional polyelectrolyte flocculation mechanisms (bridging, charge neutralization or charge patch) which persist at both 25°C and 50°C when counter-ionic PNIPAM is used. On the other hand, it was possible to obtain rapid sedimentation with the counter-ionic PNIAPMs even when they were added to the suspension already at 50°C, a process which has not been possible with neutral PNIPAM homopolymers.     

Adsorption of aerosol-OT to sapphire: lamellar structures studied with neutrons

The adsorption of sodium bis 2-ethylhexyl sulfosuccinate, NaAOT, to a sapphire surface from aqueous solution has been studied by neutron reflection at concentrations above the critical micelle concentration (cmc). Complementary measurements of the bulk structure were made with small-angle neutron scattering and grazing incidence small-angle neutron scattering. At a concentration of about 1% wt (10 × cmc), lamellar phase NaAOT was observed both at the surface and in the bulk. The structure seen at the interface for a solution of 2% wt NaAOT is a 35 ± 2 ? thick bilayer adsorbed to the sapphire surface at maximum packing density, followed by an aligned stack of fluctuating bilayers of thickness 51 ± 2 ? and with an area per molecule of 40 ± 2 ?(2). Each bilayer is separated by a water: at 25 °C, this layer is 148 ± 2 ?. A simple model for the reflectivity from fluctuating layers is presented, and for 2.0% wt NaAOT the fluctuations were found to have an amplitude of 25 ± 5 ?. The temperature sensitivity of the structure at the surface was investigated in the range 15-30 °C. The effect of temperature was pronounced, with the solvent layer becoming thinner and the volume occupied by the NaAOT molecules in a bilayer increasing with temperature. The amplitude of the fluctuations, however, is approximately temperature independent in this range. The adsorption of NaAOT at the sapphire surface resembles that previously found at hydrophilic and hydrophobic silica surfaces. The coexisting bulk lamellar phase has a spacing of layers similar to that observed at the surface. These observations are an indication that the major driving force for adsorption is self-assembly, independent of the chemical nature of the interface.     

Relationship between the polymer/silica interaction and properties of silica composite materials

Cast film composites have been prepared from aqueous polymer solutions containing nanometric silica particles. The polymers were polyvinyl alcohol (PVA), hydroxypropylmethylcellulose (HPMC) and a blend of PVA‐HPMC polymers. In the aqueous dispersions, the polymer–silica interactions were studied through adsorption isotherms. These experiments indicated that HPMC has a high affinity for silica surfaces, and can adsorb at high coverage; conversely, low affinity and low coverage were found in the case of PVA. In the films, the organization of silica particles was investigated through transmission electron microscopy (TEM) and small‐angle neutron scattering (SANS). Both methods showed that the silica particles were well‐dispersed in the HPMC films and aggregated in the PVA films. The mechanical properties of the composite films were evaluated using tensile strength measurements. Both polymers were solid materials, with a high‐elastic modulus (65 MPa for HPMC and 291 for PVA) and a low‐maximum elongation at break (0.15 mm for HPMC and 4.12 mm for PVA). In HPMC films, the presence of silica particles led to an increase in the modulus and a decrease in the stress at break. In PVA films, the modulus decreased but the stress at break increased upon adding silica. Accordingly, the polymer/silica interaction can be used to tune the mechanical properties of such composite films. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1134–1146, 2006     

Cellulase Production by Aspergillus japonicus URM5620 Using Waste from Castor Bean (Ricinus communis L.) Under Solid-State Fermentation

The activity of β-glucosidase (βG), total cellulase (FPase) and endoglucanase (CMCase), produced by Aspergillus japonicus URM5620, was studied on solid-state fermentation using castor bean meal as substrate. The effect of the substrate amount, initial moisture, pH, and temperature on cellulase production was studied using a full factorial design (2(4)). The maximum βG, FPase, and CMCase activity was 88.3, 953.4, and 191.6 U/g dry substrate, respectively. The best enzyme activities for all three enzymes were obtained at the same conditions with 5.0 g of substrate, initial moisture 15% at 25 °C and pH 6.0 with 120 h of fermentation. The optimum activity for FPase and CMCase was found at pH 3.0 at an optimum temperature of 50 °C for FPase and of 55 °C for CMCase. The cellulases were stable in the range of pH 3.0-10.0 at 50 °C temperature. The enzyme production optimization demonstrated clearly the impact of the process parameters on the yield of the cellulolytic enzymes.     

Adsorption of non-ionic surfactants to the sapphire/solution interface--effects of temperature and pH

The adsorption of the non-ionic surfactants tetraoxyethylene glycol monododecyl ether (C(12)EO(4)), pentaoxyethylene glycol monododecyl ether (C(12)EO(5)), and hexaoxyethylene glycol monododecyl ether (C(12)EO(6)) to single crystal sapphire substrates has been studied using specular neutron reflection for solutions at the critical micelle concentration. The effects of temperature and pH of the solutions were studied as well as the differences between two different crystal faces, the C and the R planes. At neutral pH, significant adsorption was only observed when the temperature was raised above the cloud temperature. This adsorption was reversible and surfactant was displaced on cooling. Reducing the pH to 3 results in significantly increased adsorption of C(12)EO(5) at 25°C with a central layer consisting mainly of surfactant (about 90%) on the C-plane substrate. A slightly smaller surface excess was observed for the R-plane. This contrasts with the significantly lower density observed even at high temperatures at neutral pH on both substrates. The results suggest that for neutral solutions surfactant association above the cloud point is the primary driving force for adsorption. At low pH, specific interactions with protonated surfaces are important. The structures of the highly hydrated layers are similar to those found for the surfactants at hydrophilic silica surfaces.     

Polypyrrole/hexagonally ordered silica nanocomposite as a novel fiber coating for solid-phase microextraction

A highly porous fiber coated polypyrrole/hexagonally ordered silica (PPy/SBA15) materials were prepared for solid-phase microextraction (SPME). The PPy/SBA15 nanocomposite was synthesized by an in situ polymerization technique. The resulting material was characterized by the scanning electron microscopy, thermogravimetric analysis and differential thermal analysis. The prepared nanomaterial was immobilized onto a stainless steel wire for fabrication of the SPME fiber. The fiber was evaluated for the extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions in combination with gas chromatography-mass spectrometry (GC-MS). A one at-the-time optimization strategy was applied for optimizing the important extraction parameters such as extraction temperature, extraction time, ionic strength, stirring rate, desorption time and desorption temperature. In optimum conditions (extraction temperature 70°C, extraction time 20 min, ionic strength 20% (WV(-1)), stirring rate 500 rpm, desorption temperature 270°C, desorption time 5 min) the repeatability for one fiber (n=3), expressed as relative standard deviation (R.S.D. %), was between 5.0% and 9.3% for the tested compounds. The quantitation limit for the studied compounds were between 13.3 and 66.6 pg mL(-1). The life span and stability of the PPy/SBA15 fiber are good, and it can be used more than 50 times at 260°C without any significant change in sorption properties. The developed method offers the advantage of being simple to use, with shorter analysis times, lower cost of equipment, thermal stability of fiber and high relative recovery in comparison to conventional methods of analysis.     

Separation of peptides with an aqueous mobile phase by temperature-responsive chromatographic column

Peptide separation technology is significant and is still an analytical challenge in proteomic studies. We report a simple preparation method for poly(N-isopropylacrylamide) grafted silica through the copolymerization of N-isopropylacrylamide with acetyl moieties immobilized on the silica surfaces. Differential scanning calorimetry results indicated that the prepared silica exhibited a sharp phase transition at 35.03°C. Silica grafted with poly(N-isopropylacrylamide) was evaluated as a temperature-responsive chromatography medium for the separation of peptides using 0.2 M NaCl solution as a mobile phase. Results indicated that at 10°C, the peptides were not resolved, but baseline separation with prolonged retention time at 50°C was attained. Particularly, a mixture of four peptides was efficiently separated within 8 min. The theoretical plate number of every peptide was more than 2500, and the resolutions were more than 3.40. The increased selectivity of the temperature-responsive column resulted from the temperature-modulated hydrophobic interaction with peptides. The retention times of these peptides were related to their hydrophobicities. This protocol provided a reliable set of chromatographic tool usable across all research and development applications that required isolation and analysis of peptides. It may represent a step forward in the complex analysis of hydrophobic and other proteins.     

Annealing of silica to reduce the concentration of isolated silanols and peak tailing in reverse phase liquid chromatography

Non-porous, colloidal silica particles were annealed at three different temperatures, 800, 900 and 1050 °C. The adsorption of lysozyme, a probe of surface roughness, was consistent with progressively reduced surface roughness as temperature increased. The heat treated silica particles were rehydroxylated and then used to pack UHPLC columns. The cationic protein lysozyme was used to probe silanol activity, which exhibited progressively less tailing as the annealing temperature increased. FTIR spectroscopy confirmed that the abundance of isolated silanols on the surface was reduced by annealing at 900 °C or 1050 °C. FTIR also revealed that there was markedly increased hydrogen bonding of the isolated silanols to neighbors after rehydroxylation. These results combine to support the hypothesis that (a) isolated silanols on silica cause tailing in RP-LC and (b) nonplanar topography gives rise to isolated silanols.     

The effect of hydrothermal treatment on column performance for monolithic silica capillary columns

Monolithic silica capillary columns with i.d. 100 μm and monolithic silica rods were prepared with tetramethoxysilane (TMOS) or a mixture of TMOS and metyltrimethoxysilane (MTMS) using different hydrothermal treatments at T=80 °C or 120 °C. Nitrogen physisorption was applied for the pore characterization of the rods and inverse size exclusion chromatography (ISEC) for that of the capillary columns. Using nitrogen physisorption, it was shown change of pore size and surface area corresponds to that of hydrothermal treatment and silica precursor. The results from ISEC agreed well with those from nitrogen physisorption regarding the pore size distribution (PSD). In addition, the retention factors for hexylbenzene with the ODS-modified capillary columns in methanol/water=80/20 at T=30 °C could also support the results from nitrogen physisorption. Furthermore, column efficiency for the columns was evaluated with alkylbenzenes and three kinds of peptides, leucine-enkephalin, angiotensin II, and insulin. Column efficiency for alkylbenzenes was similar independently of the hydrothermal treatment at T=120 °C. Even for TMOS columns, there was no significant difference in column efficiency for the peptides despite the difference in hydrothermal treatment. In contrast, for hybrid columns, it was possible to confirm the effect on hydrothermal treatment at T=120 °C resulting in a different column efficiency, especially for insulin. This difference supports the results from both nitrogen physisorption and ISEC, showing the presence of more small pores of ca. 3-6 nm for a hybrid silica without hydrothermal treatment at T=120 °C. Consequently, the results suggest that hydrothermal treatment for a hybrid column with higher temperature or longer time is necessary, compared to that for a TMOS column, to provide higher column efficiency with increase in molecular size of solute.     

硅胶自溶液中吸附胆固醇和卵磷脂

卵磷脂和胆固醇是细胞膜的主要组成,它们在不同界面上的定向排列方式对细胞膜的结构与功能起着重要的作用。用固体物质自非水溶剂中吸附类脂化合物形成类脂单层,再自水溶液中吸附蛋白质,可制成固体载体上的模拟生物膜。在固体表面上的类脂单层膜中类脂分子的定向方式与溶剂和固体表面性质有关。这些研究大多数是以非孔性物质为吸附剂(如aerosil,石墨化炭黑,carbochrom.等)自有机溶剂中吸附类脂化合物(主要是胆固醇和卵磷脂),根据单层饱和吸附时分子占据的面积推算单层中类脂化合物分子的取向。实际应用的吸附剂大多是孔性的,因此研究类脂化合物在孔性吸附剂(如,硅胶、活性炭等)上的吸附机理更有实际意义。     

Catalytic and Thermodynamic Properties of a Tannase Produced by Aspergillus niger GH1 Grown on Polyurethane Foam

Tannase is an inducible enzyme with important applications in the food and pharmaceutical industries. This enzyme was produced by the fungus Aspergillus niger GH1 under solid-state fermentation using polyurethane foam as solid support and tannic acid as sole carbon source and tannase inducer. Physicochemical properties of A. niger tannase were characterized, and the kinetic and thermodynamics parameters on methyl gallate hydrolysis were evaluated. The enzyme was stable in a pH range of 2-8 and a functional temperature range of 25-65 °C. The highest k(cat) value was 2,611.10 s(-1) at 65 °C. Tannase had more affinity for methyl gallate at 45 °C with a K(M) value of 1.82 mM and an efficiency of hydrolysis (k(cat)/K(M)) of 330.01 s(-1) mM(-1). The lowest E(a) value was found to be 21.38 kJ/mol at 4.4 mM of methyl gallate. The lowest free energy of Gibbs (ΔG) and enthalpy (ΔH) were found to be 64.86 and 18.56 kJ/mol, respectively. Entropy (ΔS) was -0.22 kJ/mol K. Results suggest that the A. niger GH1 tannase is an attractive enzyme for industrial applications due its catalytic and thermodynamical properties.     

Tuning the mechanical properties of silica microcapsules

Heat treatment is a standard method to increase the hardness of silica in various applications. Here, we tested the effect of high temperature annealing on the mechanical properties of silica microcapsules by force spectroscopy under point loads applied to the particle shell. The Young's modulus of the shells moderately increases after annealing at temperatures above 500 °C. Temperatures over 850 °C result in a much stronger increase and the Young's modulus is close to that of fused silica after annealing at 1100 °C. NMR analysis revealed that in untreated microcapsules synthesized by seeded growth using the St?ber method only 55% of the silicon atoms form siloxane bonds with four neighbors, whereas the remaining ones only form three or less siloxane bonds each and, thus, a large number of ethoxy and silanol groups still exist. During annealing at 500 °C, these are successively transformed into siloxane bonds through condensation reactions. This process correlates with only a moderate increase in Young's modulus. The strong increase at temperatures above 850 °C was associated with a densification which was associated by a decrease in capsule size and shell thickness while the shells remained homogenous and of spherical shape. The main strengthening of the shells is thus mainly due to compaction by sintering at length scales significantly larger than that of local siloxane bonds.     

Curvature effect on nanometer-scale surface properties of phospholipid layers

Phospholipid bilayers were formed through liposome fusion on surfaces with different curvatures that were defined with silica spheres deposited on silicon water. Prior to the fusion, the surfaces became hydrophobic with octadecyltrimethoxysilane solution. Using atomic force microscope, surface forces were measured on dipalmitoylphosphatidylcholine (DPPC) layers and dioleoylphosphatidylcholine (DOPC) layers upon the curvature at 25°C. The short-range repulsions were higher at 20 and 100 nm curvatures than other curvatures for the DPPC layer, while they were lower for the DOPC layer. Since it was known that the forces are related to its low mechanical stability of the lipid layer, this opposite behavior was analyzed in terms of stability upon the curvature, which appears to be eventually determined by the correlation between the lipid molecule geometry and the surface curvature.     

Effect of temperature on the sorption of europium on alumina: microcalorimetry and batch experiments

The determination of enthalpies of reactions (aqueous and surface complexation) is used in this work to model the temperature effect on the adsorption processes. Microcalorimetry experiments were carried out to determine the enthalpy of adsorption of europium on γ-alumina at 25 °C. The stability constants at 50 °C were then calculated with the van't Hoff equation, and a 2-pK approach was used to model the adsorptive behavior of Eu on alumina at 50 °C, as a function of pH. The results have shown that the adsorption of Eu(3+) on the alumina surface is weakly endothermic. In the experimental conditions considered in the present study, the temperature has only a small effect on the adsorption reaction.     

Monolithic silica rod columns for high-efficiency reversed-phase liquid chromatography

Chromatographic properties of a new type of monolithic silica rod columns were examined. Silica rod columns employed for the study were prepared from tetramethoxysilane, modified with octadecylsilyl moieties, and encased in a stainless-steel protective column with two polymer layers between the silica and the stainless-steel tubing. A 25 cm column provided up to 45,000 theoretical plates for aromatic hydrocarbons, or a minimum plate height of about 5.5 μm, at optimum linear velocity of ca. 2.3 mm/s and back pressure of 7.5 MPa in an acetonitrile-water (80/20, v/v) mobile phase at 40°C. The permeability of the column was similar to that of a column packed with 5 μm particles, with K(F) about 2.4×10(-14) m(2) (based on the superficial linear velocity of the mobile phase), while the plate height value equivalent to that of a column packed with 2.5 μm particles. Generation of 80,000-120,000 theoretical plates was feasible with back pressure below 30 MPa by employing two or three 25 cm columns connected in series. The use of the long columns enabled facile generation of large numbers of theoretical plates in comparison with conventional monolithic silica columns or particulate columns. Kinetic plot analysis indicates that the monolithic columns operated at 30 MPa can provide faster separations than a column packed with totally porous 3-μm particles operated at 40 MPa in a range where the number of theoretical plates (N) is greater than 50,000.     

Phase transitions of an ionic liquid self-assembled monolayer on Au

The properties of a surface modified with an ionic liquid self-assembled monolayer (IL-SAM) can be tuned by simply changing the deposition temperature. Mid-IR, SERS, and molecular modelling demonstrated that 1-(12-mercaptododecyl)-3-methylimidazolium bromide (MDMIBr) exhibited a crystalline monolayer for deposition temperatures below 25 °C. Above 25 °C, the aliphatic chain collapsed into a disordered conformation. At 40 °C, another phase transition occurs due to the imidazolium group tilting parallel to the surface. Consequently, the wettability of IL-SAM was tuned over a broad range of contact angle (from 20° to nearly 40°) by varying the deposition temperature. Permeation of redox mediators to a Au electrode coated with MDMIBr strongly depends on the net charge of the redox mediator. Electron transfer was excellent for neutral and negatively charged redox mediators on electrodes coated with IL-SAM regardless of deposition temperature.     

The shell dissolution of various empty hard capsules

The shell dissolution properties of gelatine, gelatine/polyethylene glycol (PEG) and hydroxypropyl methylcellulose (HPMC) capsules were studied as a function of temperature, dissolution medium, and after different storage conditions. In any dissolution medium with a pH below or equal to 5.8, HPMC capsule shells dissolved rapidly, and there was no difference in the time in which dissolution occurred in the tested temperature interval of 10 to 55 degrees C. Gelatine and gelatine/PEG capsule shells, generally, did not dissolve at temperatures below 30 degrees C. The shell dissolution time of all capsules tested was prolonged and more variable in mixed phosphate buffer pH = 6.8. The addition of enzymes (pepsin, pancreatin) to any dissolution medium was found not to enhance the differences between the different types of capsules investigated. In practical terms, the results indicated that capsule formulations should not be taken with drinks from the carbonated Cola-type. Gelatine containing capsules should preferably be administered with a warm drink, whereas HPMC capsules could be given with cold or warm drinks. The latter type of capsules should also be preferred for preparations to be taken in the fasted state. A short storage of gelatine containing capsules under hot humid tropical conditions appeared not to alter the dissolution properties of the shells, and changes in disintegration times and dissolution times of formulations filled in such capsules might be a reflection of changes of the powders incorporated rather than of the capsule shells. However, a short storage of HPMC capsules under such conditions appeared to influence the capsule shell matrix.     

Temperature-responsive solid-liquid separations with charged block-copolymers of poly(N-isopropyl acryamide)

Temperature responsive charged block-copolymers of poly(N-isopropylacrylamide) (PNIPAM) have been used in the solid-liquid separation of alumina mineral particles from aqueous solution. The effects of temperature, polymer charge-sign and fraction of charged segment have been investigated. Batch settling and adsorption studies showed that rapid sedimentation results for suspensions with polymers of opposite charge-sign to the particle surface-charge (counterionic) at 50 °C. Cooling the suspensions after flocculation at 50 °C was found to increase the final solids volume fraction of the sediment beds formed through a mechanism related to partial desorption of polymer and the reduction of the hydrophobic attraction. Suspension stability results after dosing with polymers of similar charge-sign to the particle surface-charge (co-ionic) at both 25 and 50 °C. Increasing the amount of polymer charge increased the influence of polymer charge-sign on the adsorption and solid-liquid separation behavior. The performance of the charged block copolymers are compared to that of the random charged copolymer and neutral homopolymer PNIPAM structures.     

Thermoresponsive hydrogel of diblock methylcellulose: formation of ribbonlike supramolecular nanostructures by self-assembly

This article provides detailed insight into the thermoresponsive gelation mechanism of industrially produced methylcellulose (MC), highlighting the importance of diblock structure with a hydrophobic sequence of 2,3,6-tri-O-methyl-glucopyranosyl units for this physicochemical property. We show herein, for the first time, that well-defined diblock MC self-assembles thermoresponsively into ribbonlike nanostructures in water. A cryogenic transmission electron microscopy (cryo-TEM) technique was used to detect the ribbonlike nanostructures formed by the diblock copolymers consisting of hydrophilic glucosyl or cellobiosyl and hydrophobic 2,3,6-tri-O-methyl-cellulosyl blocks, methyl β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-celluloside 1 (G-236MC, DP(n) = 10.7, DS = 2.65), and methyl β-d-glucopyranosyl-(1→4)-β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-celluloside 2 (GG-236MC, DP(n) = 28.2, DS = 2.75). Rheological measurements revealed that the gel strength of a dispersion of GG-236MC (2, 2.0 wt %) in water at 70 °C was 3.0 times stronger than that of commercial MC SM-8000, although the molecular weight of GG-236MC (2) having M(w) = 8 × 10(3) g/mol was 50 times smaller than that of SM-8000 having M(w) = 4 × 10(5) g/mol. Cryo-TEM observation suggested that the hydrogel formation of the diblock copolymers could be attributed to the entanglement of ribbonlike nanostructures self-assembled by the diblock copolymers in water. The cryo-TEM micrograph of GG-236MC (2) at 5 °C showed rectangularly shaped nanostructures having a thickness from 11 to 24 nm, although G-236MC (1) at 20 °C showed no distinct self-assembled nanostructures. The ribbonlike nanostructures of GG-236MC (2) having a length ranging from 91 to 864 nm and a thickness from 8.5 to 27.1 nm were detected above 20 °C. Small-angle X-ray scattering measurements suggested that the ribbonlike nanostructures of GG-236MC (2) consisted of a bilayer structure with a width of ca. 40 nm. It was likely that GG-236MC (2) molecules were oriented perpendicularly to the long axis of the ribbonlike nanostructure. In addition, wide-angle X-ray scattering measurements revealed that GG-236MC (2) in its hydrogel formed the same crystalline regions as 2,3,6-tri-O-methylcellulose. The influence of the DP of diblock MC with a DS of around 2.7 on the gelation behavior will be discussed.