Stabilization and acidic dissolution mechanism of single-crystalline ZnO(0001) surfaces in electrolytes studied by in-situ AFM imaging and ex-situ LEED

A combined approach of pH-dependent in-situ AFM topography and ex-situ LEED studies of the stability and dissolution of single-crystalline ZnO(0001)-Zn surfaces in aqueous media is presented. Hydroxide-stabilized and single-crystalline ZnO(0001)-Zn surfaces turned out to be stable within a wide pH range between 11 and 4 around the point of zero charge of pH PZC = 8.7 +/- 0.2. Hydroxide stabilization turned out to be a very effective stabilization mechanism for polar oxide surfaces in electrolyte solutions. The dissolution of the oxide surface started at an acidic pH level of 5.5 and occurred selectively at the pre-existing step edges, which consist of nonpolar surfaces. In comparison, the oxide dissolution along the ZnO(0001) direction proved to be effectively inhibited above a pH value of 3.8. On the basis of these microscopic observations, the mechanistic understanding of the acidic dissolution process of ZnO could be supported. Moreover, both the in-situ AFM and the ex-situ LEED studies showed that the stabilization mechanism of the ZnO(0001) surfaces changes in acidic electrolytes. At pH values below 3.8, the hydroxide-stabilized surface is destabilized by dissolution of the well-ordered radical3. radical3. R30 hydroxide ad-layer as proven by LEED. Restabilization occurs and leads to the formation of triangular nanoterraces with a specific edge termination. However, below pH 4 the surface structure of the crystal itself is ill-defined on the macroscopic scale because preferable etching along crystal defects as dislocations into the bulk oxide results in very deep hexagonal etching pits.     

Self-assembled monolayers of alkylphosphonic acid on GaN substrates

In this paper we describe the formation and characterization of self-assembled monolayers of octadecylphosphonic acid (ODPA) on epitaxial (0001) GaN films on sapphire. By immersing the substrate in its toluene solution, ODPA strongly adsorbed onto UV/O 3-treated GaN to give a hydrophobic surface. Spectroscopic ellipsometry verified the formation of a well-packed monolayer of ODPA on the GaN substrate. In contrast, adsorption of other primarily substituted hydrocarbons (C n H 2 n+1 X; n = 16-18; X = -COOH, -NH 2, -SH, and -OH) offered less hydrophobic surfaces, reflecting their weaker interaction with the GaN substrate surfaces. A UV/O 3-treated N-polar GaN had a high affinity to the -COOH group in addition to ODPA, possibly reflecting the basic properties of the surface. These observations suggested that the molecular adsorption was primarily based on hydrogen bond interactions between the surface oxide layer on the GaN substrate and the polar functional groups of the molecules. The as-prepared ODPA monolayers were desorbed from the GaN substrates by soaking in an aqueous solution, particularly in a basic solution. However, ODPA monolayers heated at 160 degrees C exhibited suppressed desorption in acidic and neutral aqueous solution maybe due to covalent bond formation between ODPA and the surface. X-ray photoelectron spectroscopy provided insight into the effect of the UV/O 3 treatment on the surface composition of the GaN substrate and also the ODPA monolayer formation. These results demonstrate that the surface of a GaN substrate can be tailored with organic molecules having an alkylphosphonic acid moiety for future sensor and device applications.     

Grafting of nanoporous alumina membranes and films with organic acids

In this study, direct surface grafting of nanoporous alumina membranes and glass‐supported alumina films was carried out with three different fluorinated organic acids: trifluoroacetic acid, perfluoropentanoic acid and 2,3,4,5,6‐pentafluorobenzoic acid. Elemental surface composition and chemical environment of alumina were investigated using X‐ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). Alumina surfaces grafted with fluoro‐organic acids exhibited increased hydrophobic properties compared to ungrafted surfaces when measured using goniometry and atomic force microscopy (AFM). This work describes the evidence for surface chemical modification of alumina using direct reaction with organic acids. An AFM study of the adsorption of the immunoglobulin G (IgG) molecules on the fluoro‐organic‐acid‐grafted surfaces is reported. The results show that an ordered arrangement of immunoglobulin G structures with in‐filling of pores could be achieved only on the more hydrophobic fluoro‐organic‐acid‐grafted alumina membranes. Copyright © 2007 John Wiley & Sons, Ltd.     

Adsorption and desorption of stearic acid self-assembled monolayers on aluminum oxide

Development of coatings to minimize unwanted surface adsorption is extremely important for their use in applications, such as sensors and medical implants. Self-assembled monolayers (SAMs) are an excellent choice for coatings that minimize nonspecific adsorption because they can be uniform and have a very high surface coverage. Another equally important characteristic of such coatings is their stability. In the present study, both the bonding mechanism and the stability of stearic acid SAMs on two aluminum oxides (single-crystal C-plane aluminum oxide (sapphire) and amorphous aluminum oxide (alumina)) are investigated. The adsorption mechanism is investigated by ex situ X-ray photoelectron spectroscopy and infrared (IR) spectroscopy. The results revealed that stearic acid binds to sapphire surfaces via a bidentate interaction of carboxylate with two oxygen atoms while it binds to alumina surfaces via both bidentate and monodentate interactions. Desorption kinetics of stearic acid self-organized on both aluminum oxide surfaces into water is explored by ex situ tapping mode atomic force microscopy, IR spectroscopy, and contact angle measurements. The results exhibit that the SAMs of stearic acid formed on sapphire are not stable in water and are continuously lost through desorption. Water contact angle measurements of SAMs that are immersed in water further indicate that the desorption rate of adsorbates from atomically smooth terrace sites is substantially faster than that of adsorbates from the sites of surface defects due to weaker molecular interaction with the smooth surface. A time-dependent desorption profile of SAMs grown on amorphous alumina reveals that contact angles decrease monotonically without any regional distinction, providing further evidence for the presence of adsorption sites with different types of affinity on the amorphous alumina surface.     

DNA as invisible ink for AFM nanolithography

We have used nanografting, an atomic force microscopy (AFM)-based nanolithography technique, to fabricate thiolated DNA nanostructures on gold surfaces. The tip-guided assembly offers opportunities for locally controlling the packing order, density, and thus the thickness of the DNA patterns. By selecting proper nanografting parameters, we can embed single-stranded DNA (ssDNA) patches into a background composed of the same DNA molecule prepared by self-assembly, in which the patches remain topographically (and chemically) invisible but have much improved packing order. When the complementary DNA (cDNA) is added, the thickness of the nanografted layer increases much more dramatically than that of the self-assembled layer during the hybridization process, and as a result, the pattern emerges. Interestingly, the pattern can be reversibly hidden and shown with high fidelity simply by dehybridizing and appending the cDNA repeatedly.     

Hybridization with nanostructures of single-stranded DNA

Nanostructures of single-stranded DNA (ssDNA) were produced within alkanethiol self-assembled monolayers using nanografting, an atomic force microscopy (AFM) based lithography technique. Next, variations of the fabrication parameters, such as the concentration of ssDNA or lines per frame, allowed for the regulation of the density of ssDNA molecules within the nanostructures. The label-free hybridization of nanostructures, monitored using high-resolution AFM imaging, has proven to be highly selective and sensitive; as few as 50 molecules can be detected. The efficiency of the hybridization reaction at the nanometer scale highly depends on the ssDNA packing density within the nanostructures. This investigation provides a fundamental step toward sensitive DNA detection and construction of complex DNA architectures on surfaces.     

Nanografting of alkanethiols by tapping mode atomic force microscopy

Nanografting, an atomic force microscopy (AFM) based nanolithography technique, is becoming a popular method for patterning self-assembled monolayers (SAMs). In this technique, a nanoscale patch of a thiol-on-gold SAM is exchanged with a different thiol by the action of an AFM tip operated in contact mode at high load. The results are then imaged in topographic or lateral force microscopy again at low values of the load. One of the problems of contact mode nanografting is that monolayers of large molecules such as proteins are likely to be deformed, damaged, or even removed from the surface by contact mode imaging even when small loads are used. Furthermore, we need to note that the stiffness of the cantilevers used in contact mode is different than that of the cantilevers used in tapping mode and that tip changing in the course of an experiment can be quite inconvenient. Here, we show that a monolayer on a gold substrate can be nanografted using tapping mode AFM (also referred to as amplitude modulation AFM) rather than the commonly used contact mode. While the grafting parameters are somewhat trickier to choose, the results demonstrate that nanografting in tapping mode can make patches of the same quality as those made by contact mode, therefore allowing for gentle imaging of the grafted molecules and the whole SAM without changing the microscope tip.     

Influence of dielectric barrier plasma treatment of ZnMgAl alloy-coated steel on the adsorption of organophosphonic acid monolayers

The adsorption of octadecyl phosphonic acid (ODPA) on oxide-covered surfaces of ZnMgAl alloy coatings is described as a function of a dielectric barrier discharge (DBD) pretreatment step. The ODPA monolayer formation enables the investigation of the influence of the DBD treatment on the resulting interfacial bond formation and surface coverage. Surface characterisation by means of surface spectroscopy (PM-IRRAS, XPS) and surface electrochemistry (cyclic voltammetry) showed that the DBD pretreatment with Ar, Ar/O₂ and Ar/H₂O gas mixtures leads to improved barrier properties of the adsorbed ODPA monolayer. Moreover, during ODPA monolayer formation from ethanolic solution, a partial etching of the surface oxide layer occurs.     

Interface chemistry and molecular interactions of phosphonic acid self-assembled monolayers on oxyhydroxide-covered aluminum in humid environments

Barrier properties of self-assembled octadecylphosphonic acid (ODPA) monolayers on plasma-modified oxyhydroxide-covered aluminum surfaces were analyzed by means of in situ photoelastic modulated infrared reflection absorption spectroscopy (PM-IRRAS). The surface hydroxyl density prior to ODPA adsorption was increased by means of a low-temperature H(2)O-plasma treatment. Adsorption isotherms of H(2)O on ODPA self-assembled monolayer (SAM) modified surfaces in comparison to bare oxide covered aluminum surfaces showed that the ODPA SAM leads to a strongly reduced amount of adsorbed water based on the inability of water to form hydrogen bonds to the low-energy aliphatic surface. However, the ODPA SAM covered surfaces did not show a significant inhibition of the H(2)O/D(2)O isotope exchange reaction between the D(2)O gas phase and the hydroxyl groups of the aluminum oxyhydroxide film, as the interfacial layer between the ODPA SAM and the metal substrate, while the interfacial phosphonate group as well as the orientation of the SAM is not affected by the adsorption of water. It can be followed that the strong adhesion promoting and high corrosion resistances of organophosphonate monolayers on oxyhydroxide-covered aluminum is a result of the strong acid-base interaction of the phosphonate headgroup with the Al ions in the oxyhydroxide film, even in the presence of high interfacial water activity and the molecular interactions of the aliphatic chains. However, the barrier effect of such monolayers on the transport of water is negligible.     

Immobilization of proteins on carboxylic acid functionalized nanopatterns

The immobilization of proteins on nanopatterned surfaces was investigated using in situ atomic force microscopy (AFM) and ex situ infrared reflectance–absorption spectroscopy (IRAS). The AFM-based lithography technique of nanografting provided control of the size, geometry, and spatial placement of nanopatterns within self-assembled monolayers (SAMs). Square nanopatterns of carboxylate-terminated SAMs were inscribed within methyl-terminated octadecanethiolate SAMs and activated using carbodiimide/succinimide coupling chemistry. Staphylococcal protein A was immobilized on the activated nanopatterns before exposure to rabbit immunoglobulin G. In situ AFM was used to monitor changes in the topography and friction of the nanopatterns in solution upon protein immobilization. Complementary studies with ex situ IRAS confirmed the surface chemistry that occurred during the steps of SAM activation and subsequent protein immobilization on unpatterned samples. Since carbodiimide/succinimide coupling chemistry can be used for surface attachment of different biomolecules, this protocol shows promise for development of other aqueous-based studies for nanopatterned protein immobilization.     

Self-localization of polyacrylic acid molecules on polar ZnO(0001)-Zn surfaces

The adsorption of single polyacrylic acid (PAAc) molecules was investigated on stepped hydroxide-stabilized polar ZnO(0001)-Zn surfaces using atomic force microscope (AFM) topography and force distance spectroscopy. Stepped surfaces of ZnO(0001)-Zn were prepared by a wet chemical etching procedure and PAAc molecules were adsorbed from aqueous NaClO(4) solutions. AFM single molecule topography studies could be utilized to show that polyacrylic acid molecules specifically adsorb on the non-polar (10-10) step edge faces at low ionic strengths. The radius of gyration of the dissolved PAAc in aqueous solution was measured by means of static light scattering experiments yielding a radius of gyration of R(g)=136 nm at pH 7.4 in 50 mM NaClO(4)/NaOH solution, which is in good agreement with the size of the adsorbed PAAc molecules as measured using AFM. The obtained results could be rationalized in terms of binding-site configurations at step edges and the effect of the chemical environment on both local electric double layer charge and molecular conformation of the PAAc molecules. The point of zero charge of the ZnO(10-10) surface was measured with chemical force microscopy to be pH(PZC)=10.2 ± 0.2. The specific adsorption of polyacrylic acid at non-polar ZnO step-edges can be explained by coordinative bonds formed between the carboxylic acid group and the Zn-surface atoms. On the hydroxide stabilized polar surface only weak hydrogen bonds can be formed in addition to van-der-Waals forces. Thus a "diffusion and trapping" mechanism keeps the adsorbed PAAc molecules mobile on the ZnO(0001)-Zn surface terraces due to small interaction forces until they are trapped at the (10-10) step faces by stronger coordinative bonds from the carboxylic groups to zinc atoms located in the first atomic layer of the crystal structure.     

Evanescent wave cavity ring-down spectroscopy (EW-CRDS) as a probe of macromolecule adsorption kinetics at functionalized interfaces

Evanescent wave cavity ring-down spectroscopy (EW-CRDS) has been employed to study the interfacial adsorption kinetics of coumarin-tagged macromolecules onto a range of functionalized planar surfaces. Such studies are valuable in designing polymers for complex systems where the degree of interaction between the polymer and surface needs to be tailored. Three tagged synthetic polymers with different functionalities are examined: poly(acrylic acid) (PAA), poly(3-sulfopropyl methacrylate, potassium salt) (PSPMA), and a mannose-modified glycopolymer. Adsorption transients at the silica/water interface are found to be characteristic for each polymer, and kinetics are deduced from the initial rates. The chemistry of the adsorption interfaces has been varied by, first, manipulation of silica surface chemistry via the bulk pH, followed by surfaces modified by poly(L-glutamic acid) (PGA) and cellulose, giving five chemically different surfaces. Complementary atomic force microscopy (AFM) imaging has been used for additional surface characterization of adsorbed layers and functionalized interfaces to allow adsorption rates to be interpreted more fully. Adsorption rates for PSPMA and the glycopolymer are seen to be highly surface sensitive, with significantly higher rates on cellulose-modified surfaces, whereas PAA shows a much smaller rate dependence on the nature of the adsorption surface.     

Nanografting: modeling and simulation

We present a simple phenomenological model of the nanografting process with an emphasis on the formation of binary self-assembled monolayers. This model includes dynamical processes that are involved in natural growth experiments, including molecular deposition, surface diffusion, and the phase transition from physisorption to chemisorption, and we show that it predicts domain formation in ungrafted deposition that matches experiment. The one-order-of-magnitude faster kinetics that is found in the nanografting experiments compared to natural self-assembly (or unconstrained self-assembly) is described with a key assumption that the deposition rate is greatly enhanced in the small region confined between the back side of the AFM tip and the edge of the previously deposited self-assembled monolayer. Monte Carlo simulations based on this model reproduce experimental observations concerning the variation of SAM heterogeneity with AFM tip speed. Our simulations demonstrate that the faster the AFM tip displaces adsorbed molecules in a monolayer, the more heterogeneous are the monolayers formed behind the tip, as this allows space and time for the formation of phase-segregated domains.     

Probing colloidal forces between a Si3N4 AFM tip and single nanoparticles of silica and alumina

The atomic force microscope (AFM) has been used to measure surface forces between silicon nitride AFM tips and individual nanoparticles deposited on substrates in 10(-4) and 10(-2) M KCl solutions. Silica nanoparticles (10 nm diameter) were deposited on an alumina substrate and alumina particles (5 to 80 nm diameter) were deposited on a mica substrate using aqueous suspensions. Ionic concentrations and pH were used to manage attractive substrate-particle electrostatic forces. The AFM tip was located on deposited nanoparticles using an operator controlled offset to achieve stepwise tip movements. Nanoparticles were found to have a negligible effect on long-range tip-substrate interactions, however, the forces between the tip and nanoparticle were detectable at small separations. Exponentially increasing short-range repulsive forces, attributed to the hydration forces, were observed for silica nanoparticles. The effective range of hydration forces was found to be 2-3 nm with the decay length of 0.8-1.3 nm. These parameters are in a good agreement with the results reported for macroscopic surfaces of silica obtained using the surface force apparatus suggesting that hydration forces for the silica nanoparticles are similar to those for flat silica surfaces. Hydration forces were not observed for either alumina substrates or alumina nanoparticles in both 10(-4) M KCl solution at pH 6.5 and 10(-2) M KCl at pH 10.2. Instead, strong attractive forces between the silicon nitride tip and the alumina (nanoparticles and substrate) were observed.     

Creating patterned poly(dimethylsiloxane) surfaces with amoxicillin and poly(ethylene glycol)

This paper reports a simple microwave plasma patterning of poly(dimethylsiloxane) (PDMS) surfaces, which is accomplished by allowing selective surface areas to microwave plasma exposure in the presence of gaseous monomer. When maleic anhydride is used for microwave plasma reaction in the presence of physical barrier on the PDMS substrate, the resulting patterned surfaces with chemically bonded maleic anhydride and carboxylic acid groups are generated. In this particular study we attached amoxicillin via ammonolysis under weak base conditions in the presence of a catalyst as well as poly(ethyleneglycol) (PEG). A combination of internal reflection IR imaging (IRIRI) and atomic force microscopy (AFM) revealed that amoxicillin and PEG can be readily reacted on the microwave plasma patterned PDMS surfaces. Surface areas directly exposed to microwave plasmons exhibit the highest reactivity due to higher content of functional groups. These studies also show that molecular weight of PEG has also significant effect on kinetics of surface reactions.     

Piperidine adsorption on hydrated alpha-alumina (0001) surface studied by vibrational sum frequency generation spectroscopy

The adsorption of piperidine vapor on the hydrated alumina (alpha-Al2O3, corundum) (0001) surface was investigated using vibrational broad bandwidth and scanning sum frequency generation (SFG) spectroscopy. The interfacial vibrational signature in the C-H stretching region of piperidine at the alumina (0001) surface is shown to be a sensitive spectroscopic probe revealing the adsorption mechanism. The neat piperidine surface, aqueous piperidine surface, and aqueous piperidium chloride surface were also investigated in the C-H stretching region by SFG to establish vibrational reference frequencies. After piperidine adsorption, piperidine vapor was removed and piperidine was found to be chemisorbed onto the alumina (0001) surface through protonation by surface hydroxyl groups. The O-H stretching region of the alumina surface before and after piperidine adsorption was also investigated, and the results revealed the decrease of the surface number density of alumina surface hydroxyl groups.     

Adsorption and porosity properties of carbon-covered alumina surfaces

Uniformly carbon-covered alumina (CCA) was prepared via the carbonisation of sucrose highly dispersed on the alumina surface. Using special thermogravimetry and sorptometry methods physicochemical properties of carbon-covered alumina surfaces were investigated. A numerical and analytical procedure for the evaluation of total heterogeneous properties (desorption energy distribution and pore-size distribution functions) on the basis of liquid thermodesorption from the sample surfaces under the quasi-equilibrium conditions are presented. The desorption energy distribution was derived from the mass loss Q-TG and the differential mass loss Q-DTG curves of thermodesorption of pre-adsorbed polar and apolar liquid films. For the first time, the evaluation of the fractal dimensions of carbon-covered alumina using the sorptometry, thermogravimetry and AFM data is presented.     

Preparation of CoNi high surface area porous foams by substrate controlled electrodeposition

We demonstrate that nanofabrication of 3D dendritic CoNi alloy foams with an open porous structure can be achieved by electrodeposition onto a single-crystalline Cu(111) substrate at ambient conditions. The very low wettability of this substrate caused by its low surface energy allows tailoring the CoNi deposit morphology. This is concluded from a comparison of polycrystalline Cu substrates with single-crystalline ones of different orientations. The advantages of the present CoNi alloy foams are low internal stresses and good mechanical stability on the substrate. In a second step, by comparing the catalytic properties of the achieved foam with those of CoNi layers obtained on polycrystalline Cu substrates, it is shown that the morphology of the CoNi layers has a decisive influence on the kinetics of the surface redox reaction. The higher reaction rate makes the open foam suitable as catalyst for oxygen evolution in electrolysers. The reversibility of the redox process provides great potential for the achieved porous layers to be used as positive material in alkaline batteries.     

Fibrinogen adsorption on three silica-based surfaces: conformation and kinetics

Using AFM (atomic force microscopy) to probe protein conformation and arrangement, and TIRF (total internal reflectance fluorescence) to monitor kinetics, fibrinogen adsorption on three different silica-based surfaces was studied: the native oxide on silicon, acid-etched microscope slides, and acid-etched polished glass. The three are chemically similar, but the microscope slide is rougher and induces AFM tip instabilities that appear as high spots on the bare surface. Fibrinogen's conformation and transport-limited adsorption kinetics are found to be quantitatively similar on all three surfaces. Further, the number of adsorbed proteins in progressive AFM micrographs quantitatively match the coverages measured by TIRF during early adsorption. Surfaces appear full, via AFM, when adsorbed amounts are about an order of magnitude below their true saturation levels (via TIRF) because, above about 0.26 mg/m(2), individual proteins cannot be discerned. The results demonstrate how the appearance of AFM micrographs can be misleading regarding surface saturation. On all three surfaces, fibrinogen is, at most, slightly aggregated, showing limited, if any, surface mobility. The complexities of the microscope slide's surface landscape minimally impact adsorption.     

Mechano-chemical radical formation and polymerization initiation during wet grinding of alumina

The formation of free radicals during wet grinding of alumina in a stirred media mill was studied by using the test radical 2,2-diphenyl-1-picrylhydracyl (DPPH). The kinetics of mechano-chemical radical formation follows a zeroth-order rate law. Particle breakage as well as mechanical activation of the surface of the alumina particles contributes to the radical formation. The rate constants of the radical formation due to mechanical activation of the particle surface k(A) and due to particle breakage k(B) depend on the milling process parameters. The radical formation during wet grinding of alumina was exploited to initiate mechano-chemical polymerization reactions of acrylic acid and acryl amide, respectively. In this way nanoparticles functionalized with polyacrylic acid and polyacryl amide, respectively, are obtained. The influence of the milling process parameters on the kinetics of mechano-chemical radical formation and on the grafted amount of polymer is discussed on the basis of stress energy and number of stress events in the mill. A correlation between the grafted amount of polyacryl amide on the alumina particles and the total radical formation rate was found showing that the concentration of mechano-chemically formed free radicals governs the efficacy of a chemical reaction at activated particle surfaces.