Ni2P/TiO2的制备及其对苯加氢反应的催化性能

采用程序升温还原方法制备了TiO2负载的晶态Ni2P催化剂。用X射线衍射（XRD）及低温N2吸附（BET）等技术对样品的物相、比表面积等性质进行了表征。以苯气相加氢为模型反应考察了Ni2P/TiO2催化剂加氢性能，并对Ni2P负载量、前驱体中P的质量分数对催化剂的物相及性能的影响进行了研究。实验结果表明， TiO2负载的晶态磷化镍催化剂上，Ni2P是主要物相。Ni2P/TiO2催化剂对苯加氢反应具有较高的活性、选择性以及良好的稳定性能。Ni2P/TiO2制备对催化剂的性能有影响。Ni2P负载量增加，催化剂的活性先升高后降低，Ni2P负载量为12%时催化剂活性较高。催化剂前驱体中P的质量分数越高，制备出的催化剂对苯加氢反应的稳定性越好，但随前驱体中P的质量分数增加，催化反应的活性先升高，后降低。与Ni2P/SiO2比较，Ni2P/TiO2催化剂具有较高的活性和稳定性。     

One-electron Ni(II)/(I) redox couple: potential role in hydrogen activation and production

The three-coordinate Ni(I) complex Ni(Cl)(P(2)), where P(2) is the diphosphine (iPr)DPDBFphos, reacts with the acids HCl·(dioxane) and 2,6-lutidinium chloride to generate Ni(H)(Cl)(P(2)) and Ni(Cl)(2)(P(2)). Photolysis of the Ni(H)(X)(P(2)) (for X = Cl, Br) results in formation of H(2) and the Ni(I) halide. This reaction also proceeds in reverse when heated.     

Ni2P/HZSM5上噻吩加氢脱硫性能研究

采用程序升温还原方法制备了Ni2P/HZSM5催化剂。用X射线衍射 (XRD)、低温N2吸附（BET）、扫描电镜(SEM)等技术对催化剂样品的物相、比表面积、形貌等性质进行了表征。在连续微反系统中测定了Ni2P/HZSM5催化剂对噻吩加氢脱硫催化活性；研究了Ni2P负载量、前驱体中Ni/P摩尔比对催化剂的物相及性能的影响，考察了空速、反应温度、反应压力等操作条件对催化剂上噻吩加氢脱硫性能的影响。实验结果表明，Ni2P/HZSM5催化剂对噻吩加氢脱硫反应具有较高的活性和稳定性。随着Ni2P负载量、前驱体中Ni/P摩尔比的增加，催化剂的活性和稳定性先升高后降低。反应温度和体积空速对Ni2P/HZSM5催化剂的噻吩加氢脱硫性能有较明显的影响，反应压力和进料氢油比的影响相对较小。     

Catalysts for hydrogen evolution from the [NiFe] hydrogenase to the Ni2P(001) surface: the importance of ensemble effect

Density functional theory (DFT) was employed to investigate the behavior of a series of catalysts used in the hydrogen evolution reaction (HER, 2H(+) + 2e(-) --> H(2)). The kinetics of the HER was studied on the [NiFe] hydrogenase, the [Ni(PS3*)(CO)](1)(-) and [Ni(PNP)(2)](2+) complexes, and surfaces such as Ni(111), Pt(111), or Ni(2)P(001). Our results show that the [NiFe] hydrogenase exhibits the highest activity toward the HER, followed by [Ni(PNP)(2)](2+) > Ni(2)P > [Ni(PS3*)(CO)](1)(-) > Pt > Ni in a decreasing sequence. The slow kinetics of the HER on the surfaces is due to the fact that the metal hollow sites bond hydrogen too strongly to allow the facile removal of H(2). In fact, the strong H-Ni interaction on Ni(2)P(001) can lead to poisoning of the highly active sites of the surface, which enhances the rate of the HER and makes it comparable to that of the [NiFe] hydrogenase. In contrast, the promotional effect of H-poisoning on the HER on Pt and Ni surfaces is relatively small. Our calculations suggest that among all of the systems investigated, Ni(2)P should be the best practical catalyst for the HER, combining the high thermostability of the surfaces and high catalytic activity of the [NiFe] hydrogenase. The good behavior of Ni(2)P(001) toward the HER is found to be associated with an ensemble effect, where the number of active Ni sites is decreased due to presence of P, which leads to moderate bonding of the intermediates and products with the surface. In addition, the P sites are not simple spectators and directly participate in the HER.     

超细非晶镍合金的化学制备及类金属元素对性质的影响

常温下分别使用KBH4和NaH2PO2在水溶液中还原Ni^2^+制得了Ni65B35和Ni89P11超细非晶合金(UFAAP), 同时使用KBH4和NaH2PO2还原Ni^2^+制得了Ni73P13B14UFAAP. Ni-P的粒径较大, 约为110nm, Ni-B的粒径较小, 约为20nm,Ni-P-B的粒径居其之间, 约为40nm。XPS表明, Ni-P间的相互作用强于Ni-B间的相互作用, Ni-P-B中P的电子状态与Ni-P中的相似。Ni-P-B比Ni-P的比表面积高得多,Ni-P-B比Ni-B和Ni-P具有更好的非晶态稳定性, 在573K热处理, 它的非晶态保持完好。晶化结果也表明Ni-P-B中Ni-P间的相互作用比Ni-B间的强。     

Desulfurization reactions on Ni2P(001) and alpha-Mo2C(001) surfaces: complex role of P and C sites

X-ray photoelectron spectroscopy and first-principles density-functional calculations were used to study the interaction of thiophene, H(2)S, and S(2) with Ni(2)P(001), alpha-Mo(2)C(001), and polycrystalline MoC. In general, the reactivity of the surfaces increases following the sequence MoC < Ni(2)P(001) < alpha-Mo(2)C(001). At 300 K, thiophene does not adsorb on MoC. In contrast, Ni(2)P(001) and alpha-Mo(2)C(001) can dissociate the molecule easily. The key to establish a catalytic cycle for desulfurization is in the removal of the decomposition products of thiophene (C(x)H(y) fragments and S) from these surfaces. Our experimental and theoretical studies indicate that the rate-determining step in a hydrodesulfurization (HDS) process is the transformation of adsorbed sulfur into gaseous H(2)S. Ni(2)P is a better catalyst for HDS than Mo(2)C or MoC. The P sites in the phosphide play a complex and important role. First, the formation of Ni-P bonds produces a weak "ligand effect" (minor stabilization of the Ni 3d levels and a small Ni --> P charge transfer) that allows a high activity for the dissociation of thiophene and molecular hydrogen. Second, the number of active Ni sites present in the surface decreases due to an "ensemble effect" of P, which prevents the system from deactivation induced by high coverages of strongly bound S. Third, the P sites are not simple spectators and provide moderate bonding to the products of the decomposition of thiophene and the H adatoms necessary for hydrogenation.     

Thiophene adsorption and activation on MoP(001), gamma-Mo2N(100), and Ni2P(001): density functional theory studies

The adsorption and dissociation of thiophene on the MoP(001), gamma-Mo(2)N(100), and Ni(2)P(001) surfaces have been computed by using the density functional theory method. It is found that thiophene adsorbs dissociatively on MoP(001), while nondissociatively on gamma-Mo(2)N(100) and Ni(2)P(001). On MoP(001), the dissociation of the C-S bonds is favored both thermodynamically and kinetically, while the break of the first C-S bond on gamma-Mo(2)N(100) has an energy barrier of 1.58 eV and is endothermic by 0.73 eV. On Ni(2)P(001) there are Ni(3)P(2)- and Ni(3)P-terminated surfaces. On the Ni(3)P(2)-terminated surface, the dissociation of the C-S bonds of adsorbed thiophene is endothermic, while it is exothermic on the Ni(3)P-terminated surface.     

Synthesis of Ni2P promoted trimetallic NiMoW/γ-Al2O3 catalysts for diesel oil hydrotreatment

The Ni2P promoted and γ-Al2O3 supported NiMoW sulfide catalyst consisting of 4 wt% Mo, 22 wt% W, 2 wt% Ni and 2.5 wt% Ni2P was synthesized by a co-impregnation method. The catalysts were characterized by N2 adsorption-desorption, X-ray diffraction (XRD), diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, NH3 temperature-programmed desorption (NH3-TPD) and transmission electron microscopy (TEM). The results showed that Ni2P, Ni, Mo and W species were highly dispersed over γ-Al2O3. The hydrodesulfurization (HDS) of dibenzothiophene (DBT) showed that the presence of Ni2P brought a strong promotional effect on the HDS activity, which was further confirmed by the HDS and hydrodenitrogenation (HDN) of diesel oil under industrial conditions. The enhancement in HDN activity and stability by Ni2P addition could be attributed more to the effect of new active sites of Ni2P than that of acidity modification. The as-prepared Ni2P-NiMoW/γ-Al2O3 catalyst showed better hydrotreating performance than NiMoW/γ-Al2O3 and commercial catalysts.     

Bis­[methyl­enebis­(di­phenyl­phosphine)‐P,P′]­nickel(II) diperchlorate

The title compound, [Ni(Ph₂PCH₂PPh₂)₂](ClO₄)₂, was synthesized and its structure determined crystallographically. The Ni atom lies on an inversion centre and is at the center of a square formed by four P atoms which are necessarily coplanar. The Ni—P distances are 2.2188 (5) and 2.2322 (5) Å, and the P—Ni—P angle is 73.12 (3)°. The unique perchlorate anion is not coordinated to the Ni atom.     

水蒸气处理对Ni_2P/SiO_2催化剂催化氯苯加氢脱氯反应的促进作用

在303,514和543K下用0.8%H2O-99.2%H2对Ni2P/SiO2催化剂进行了水蒸气处理,利用N2吸附-脱附、X射线衍射、电感耦合等离子体发射光谱、H2程序升温脱附及原位漫反射红外光谱等技术对水蒸气处理前后Ni2P/SiO2催化剂的结构进行了表征,并在常压固定床反应器上评价了其催化氯苯加氢脱氯活性.结果表明,经水蒸气处理后,Ni2P/SiO2催化剂的物相及元素组成、Ni2P晶粒大小、比表面积及孔结构没有明显改变.与未处理和303K处理的Ni2P/SiO2催化剂不同,513和543K处理的催化剂表面暴露的Ni中心数量减少,表面P–OH基团数量增多.在513K,氯苯空速3.75ml/(g·h)及H2和氯苯的摩尔比为9.0的反应条件下,经不同温度水蒸气处理的Ni2P/SiO2催化剂上氯苯初始转化率高于93.8%,约是未预处理催化剂的17倍.这可能与金属Ni中心和表面P–OH基团的协同作用有关.     

碳纳米管负载Ni2P作为染料敏化太阳能电池对电极的性能研究

本文以碳纳米管(CNTs)与Ni2P纳米晶制备CNTs-Ni2P复合材料,首次研究其染料敏化太阳能电池(DSSCs)的光阴极材料性能.使用X射线衍射(XRD)和透射电子显微镜(TEM)测定材料结构,观察材料形貌.结果表明,复合材料由碳纳米管和六方结构的磷化镍构成,无其它磷化物杂相,磷化镍纳米晶(约10 nm)分散于CNTs表面.交流阻抗(EIS)测试显示,与CNTs和Ni2P对电极相比,CNTs-Ni2P对电极的电荷转移电阻和扩散阻抗较低,接近Pt-FTO对电极水平.CNTs-Ni2P对电极的DSSCs光电流达12.9 mA·cm-2,能量转化效率达5.6%,接近Pt-FTO对电极的DSSCs能量转化效率(5.9%).这归因于高电催化活性的磷化镍纳米晶与高电导CNTs的协同效应.     

从大木尺度现象看柳林香严寺毗卢殿建造年代之复杂性*

采用共沉淀法制备了高分散80%Ni/Al_2O_3催化剂,经350℃焙烧,得高分散NiO/Al_2O_3(NiO粒径～3 nm),将其以CS_2硫化(310℃, 4 h)或PPh_3磷化(320℃, 36 h),分别获得了高分散的硫化镍(Ni_3S_2和Ni_3S_4, 5.8 nm)和Ni_2P(7.0nm),在二苯并噻吩(DBT)的加氢脱硫(HDS)反应中, Ni_2P的活性远高于NiS_x(360℃时DBT的转化率分别为100%和75%).若将NiS_x用PPh_3磷化,则NiS_x全部转化为Ni_2P(13.3 nm),其HDS活性远高于原来的NiS_x且与直接磷化获得的Ni_2P(7.0 nm)相当.反之,若将Ni_2P用CS_2硫化,则Ni_2P物相不变,粒径也没有长大,表明Ni_2P物相远比NiS_x稳定,且其HDS活性高于直接磷化的Ni_2P,表明其Ni_2P表面可能生成了HDS活性更高的某种Ni-P-S物种.     

团簇Ni4P催化析氢性能研究

为探究团簇Ni₄P催化析氢最强的结构,基于密度泛函理论,在B3LYP/Lan12dz水平下,对团簇Ni₄P的初始构型进行计算和优化,得到5种优化构型。从热力学稳定性、前线轨道图和前线轨道能级差对团簇Ni₄P的析氢性能分析发现,构型1^（4）和1^（2）的热力学稳定性较强;团簇Ni₄P各优化构型均易吸附水中的氢原子,Ni原子为团簇Ni₄P催化活性位点,且构型1^（4）、1^（2）和2^（4）催化析氢的活性更强。(1^（2）)-H、(2^（2）)-H在电化学脱附法和化学重组法中均具有较强的催化活性。以上说明构型1^（2）是团簇Ni₄P催化析氢最强的结构。     

Highly selective hydrogenation of acetophenone over supported amorphous alloy catalyst

Alpha-phenylethanol (PE) is an essential chemical in the field of medicine and synthetic perfumery. Therefore, in this work, we used a supported Ni–B–P amorphous alloy catalyst (Ni–B–P/SiO₂) in the hydrogenation of acetophenone (AP) to α-PE, which demonstrated excellent catalytic activity and selectivity, compared with Ni–B/SiO₂ (KBH₄ reduction of nickel salt). Ni–B–P/SiO₂ exhibited a high AP hydrogenation conversion of approximately 99%, whereas the PE selectivity reached up to 94%, which is approximately 1.4-fold higher than that of Ni–B/SiO₂ (about 69%), thereby directly proving the unique inhibition of AP hydrogenation over hydrogenation of P in the Ni–B catalytic system. The doped P in Ni–B–P/SiO₂ enhances the oxidation resistance and maintains the valence stability of Ni and B. Furthermore, sufficient experimental data were collected to determine the kinetic parameters. Based on the Langmuir–Hinshelwood model, we assumed that (i) AP and H₂ compete for adsorption on Ni–B–P/SiO₂; (ii) AP has strong adsorptive capacity on Ni–B–P/SiO₂; and (iii) PE coverage on the catalyst was negligible. Then, the dynamic equation was derived, which indicated that experimental data agree well with the dynamic model. Finally, the activation energy was confirmed to be 50.73 KJ/mol. This report will open up an avenue for the industrialization of amorphous alloy catalysts.     

Ni(P(Ph)2N(C6H4X)2)2]2+ complexes as electrocatalysts for H2 production: effect of substituents, acids, and water on catalytic rates

A series of mononuclear nickel(II) bis(diphosphine) complexes [Ni(P(Ph)(2)N(C6H4X)(2))(2)](BF(4))(2) (P(Ph)(2)N(C6H4X)(2) = 1,5-di(para-X-phenyl)-3,7-diphenyl-1,5-diaza-3,7-diphosphacyclooctane; X = OMe, Me, CH(2)P(O)(OEt)(2), Br, and CF(3)) have been synthesized and characterized. X-ray diffraction studies reveal that [Ni(P(Ph)(2)N(C6H4Me)(2))(2)](BF(4))(2) and [Ni(P(Ph)(2)N(C6H4OMe)(2))(2)](BF(4))(2) are tetracoordinate with distorted square planar geometries. The Ni(II/I) and Ni(I/0) redox couples of each complex are electrochemically reversible in acetonitrile with potentials that are increasingly cathodic as the electron-donating character of X is increased. Each of these complexes is an efficient electrocatalyst for hydrogen production at the potential of the Ni(II/I) couple. The catalytic rates generally increase as the electron-donating character of X is decreased, and this electronic effect results in the favorable but unusual situation of obtaining higher catalytic rates as overpotentials are decreased. Catalytic studies using acids with a range of pK(a) values reveal that turnover frequencies do not correlate with substrate acid pK(a) values but are highly dependent on the acid structure, with this effect being related to substrate size. Addition of water is shown to dramatically increase catalytic rates for all catalysts. With [Ni(P(Ph)(2)N(C6H4CH2P(O)(OEt)2)(2))(2)](BF(4))(2) using [(DMF)H](+)OTf(-) as the acid and with added water, a turnover frequency of 1850 s(-1) was obtained.     

磷化镍/介孔TiO_2催化剂的制备及其催化加氢脱硫性能

以介孔TiO2(m-TiO2)为载体,采用程序升温还原法制备了Ni2P/m-TiO2催化剂,考察了不同起始Ni/P摩尔比及活性组分负载量对该催化剂结构及其催化加氢脱硫(HDS)性能的影响.结果表明,当Ni/P摩尔比为1.25时,活性组分以Ni2P为主,催化剂的最佳Ni负载量为10%.采用X射线衍射、低温N2吸附-脱附、场发射扫描电镜和程序升温还原等技术表征了m-TiO2及其它不同载体负载的Ni2P催化剂.结果表明,高结晶度m-TiO2载体使Ni和P物种的还原温度大幅度降低,在450～600oC还原制得的Ni2P/m-TiO2催化剂的结构参数基本一致,比表面积均为90m2/g左右,具有很高的热稳定性和对二苯并噻吩的HDS催化性能.在相同的反应条件下,m-TiO2负载的Ni2P催化剂HDS性能最好,各载体负载的Ni2P催化剂活性大小顺序为Ni2P/m-TiO2Ni2P/SiO2Ni2P/P25.     

化学镀镍-高磷合金晶化行为的现场XRD研究

从柠檬酸-酒石酸-乳酸-EDTA混合体系中得到含P 12％(质量比)的化学镀高磷Ni-P合金，其差热曲线显示，在350和420 ℃出现两个放热过程.现场XRD分析结果显示，镀层在300 ℃以下保持非晶态结构，在320 ℃之后开始晶化，首先析出介稳的Ni5P2和Ni12P5相，在360 ℃后开始有稳定的Ni3P和Ni相的衍射峰出现， 400 ℃以上只有Ni3P和Ni相. 325 ℃恒温时，镀层在4 min内保持非晶态的衍射特征，随即析出Ni5P2和Ni12P5相, 并在2 h内基本保持不变. 350 ℃恒温时，析出的Ni5P2和Ni12P5介稳相只存在40 min.实验结果表明, DTA曲线上350 ℃的放热峰不仅有非晶相转变为介稳相的过程，也包含部分介稳相转化为稳定相的过程.     

Three-coordinate NiII: tracing the origin of an unusual, facile Si-C(sp3) bond cleavage in [(tBu2PCH2SiMe2)2N]Ni+

All attempts to synthesize (PNP)Ni(OTf) form instead ((t)Bu(2)PCH(2)SiMe(2)NSiMe(2)OTf)Ni(CH(2)P(t)Bu(2)). Abstraction of F(-) from (PNP)NiF by even a catalytic amount of BF(3) causes rearrangement of the (transient) (PNP)Ni(+) to analogous ring-opened [((t)Bu(2)PCH(2)SiMe(2)NSiMe(2)F)]Ni(CH(2)P(t)Bu(2)). Abstraction of Cl(-) from (PNP)NiCl with NaB(C(6)H(3)(CF(3))(2))(4) in CH(2)Cl(2) or C(6)H(5)F gives (PNP)NiB(C(6)H(3)(CF(3))(2))(4), the key intermediate in these reactions is (PNP)Ni(+), [(PNP)Ni](+), in which one Si-C bond (together with N and two P) donates to Ni. This makes this Si-C bond subject to nucleophilic attack by F(-), triflate, and alkoxide/ether (from THF). This σ(Si-C) complex binds CO in the time of mixing and also binds chloride, both at nickel. Evidence is offered of a "self-healing" process, where the broken Si-C bond can be reformed in an equilibrium process. (PNP)Ni(+) reacts rapidly with H(2) to give (PN(H)P)NiH(+), which can be deprotonated to form (PNP)NiH. A variety of nucleophilic attacks (and THF polymerization) on the coordinated Si-C bond are envisioned to occur perpendicular to the Si-C bond, based on the character of the LUMO of (PNP)Ni(+).     

Ni2P加氢脱硫催化剂

环境法规对硫氧化物脱出的限制日益严格以及原油品质的不断下降,使得有必要研发高效的加氢脱硫催化剂。Ni2P由于具有优异的加氢脱硫活性和稳定性,引起了广泛的关注。本文综述了Ni2P加氢脱硫催化剂的特性、反应活性相、制备方法、改进和加氢脱硫活性等方面的研究进展。在Ni2P中存在两种不同的初始活性位,四面体几何构型的Ni(1)初始活性位在加氢脱硫反应中参与直接脱硫反应,四方锥几何构型的Ni(2)初始活性位则与催化剂的高加氢活性有关。在加氢脱硫反应中,催化剂表面生成的NixSyP相被认为是真正的活性相。制备Ni2P的方法主要是程序升温还原和液相合成。载体、助剂和络合剂对Ni2P活性相的形成和催化剂的活性有重要影响。相比于商用硫化物催化剂,Ni2P催化剂对噻吩、二苯并噻吩和4,6-二甲基二苯并噻吩均表现出更高的加氢脱硫活性。     

柠檬酸络合法制备Ni2P/SBA-15催化剂及加氢脱硫性能

以介孔分子筛SBA-15为载体,Ni组分采用柠檬酸(CA)配合法,制备了Ni2P质量含量为25%～45%、P/Ni为0.8、CA/Ni为0～1.5的一系列CA-Ni2P/SBA-15催化剂.利用XRD和N2吸脱附表征了催化剂结构,以二苯并噻吩(DBT)为模型硫合物,对催化剂加氢脱硫(HDS)性能进行了评价,考察了CA/Ni比对催化剂结构和反应性能的影响.结果表明,催化剂仍然保持有介孔结构,催化活性物相为Ni2P.反应温度为300～340℃时,Ni2P含量和CA/Ni比都对催化剂的性能有一定的影响,反应温度在360℃以上时,Ni2P含量和CA/Ni比对催化剂性能的影响不明显.Ni2P含量为35%、CA/Ni比为1.0的催化剂具有最好的HDS活性,DBT的转化率可达98%.