Ultra-sensitive determination of cyanide in surface water by gas chromatography–tandem mass spectrometry after derivatization with 2-(dimethylamino)ethanethiol

A gas chromatography–tandem mass spectrometric (GC–MS/MS) method has been established for the determination of cyanide in surface water. This method is based on the derivatization of cyanide with 2-(dimethylamino)ethanethiol in surface water. The following optimum reaction conditions were established: reagent dosage, 0.7 g L⁻¹ of 2-(dimethylamino)ethanethiol; pH 6; reaction carried out for 20 min at 60 °C. The organic derivative was extracted with 3 mL of ethyl acetate, and then measured by using GC–MS/MS. Under the established conditions, the detection and quantification limits were 0.02 μg L⁻¹ and 0.07 μg L⁻¹ in 10-mL of surface water, respectively. The calibration curve had a linear relationship relationship with y = 0.7140x + 0.1997 and r² = 0.9963 (for a working range of 0.07–10 μg L⁻¹) and the accuracy was in a range of 98–102%; the precision of the assay was less than 7% in surface water. The common ions Cl⁻, F⁻, Br⁻, NO₃⁻, SO₄²⁻, PO₄³⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺, Fe²⁺ and sea water did not interfere in cyanide detection, even when present in 1000-fold excess over the species. Cyanide was detected in a concentration range of 0.07–0.11 μg L⁻¹ in 6 of 10 surface water samples.     

A new BOD estimation method employing a double-mediator system by ferricyanide and menadione using the eukaryote Saccharomyces cerevisiae

A new biochemical oxygen demand (BOD) sensing method employing a double-mediator (DM) system coupled with ferricyanide and a lipophilic mediator, menadione and the eukaryote Saccharomyces cerevisiae has been developed. In this study, a stirred micro-batch-type microbial sensor with a 560 μL volume and a two-electrode system was used. The chronamperometric response of this sensor had a linear response between 1 μM and 10 mM hexacyanoferrate(II) (r² = 0.9995, 14 points, n = 3, average of relative standard deviation and R.S.D._av = 1.3%). Next, the optimum conditions for BOD estimation by the DM system (BOD_DM) were investigated and the findings revealed that the concentration of ethanol, used to dissolve menadione, influenced the sensor response and a relationship between the sensor output and glucose glutamic acid concentration was obtained over a range of 6.6-220 mg O₂ L⁻¹ (five points, n = 3, R.S.D._av 6.6%) when using a reaction mixture incubated for 15 min. Subsequently, the characterization of this sensor was studied. The sensor responses to 14 pure organic substances were compared with the conventional BOD₅ method and other biosensor methods. Similar results with the BOD biosensor system using Trichosporon cutaneum were obtained. In addition, the influence of chloride ion, artificial seawater and heavy metal ions on the sensor response was investigated. A slight influence of 20.0 g L⁻¹ chloride ion and artificial seawater (18.4 g L⁻¹ Cl⁻) was observed. Thus, the possibility of BOD determination for seawater was suggested in this study. In addition, no influence of the heavy metal ions (1.0 mg L⁻¹ Fe³⁺, Cu²⁺, Mn²⁺, Cr³⁺ and Zn²⁺) was observed. Real sample measurements using both river water and seawater were performed and compared with those obtained from the BOD₅ method. Finally, stable responses were obtained for 14 days when the yeast suspension was stored at 4 °C (response reduction, 93%; R.S.D. for 6 testing days, 9.1%).     

Sensitive and robotic determination of bromate in sea water and drinking deep-sea water by headspace solid-phase micro extraction and gas chromatography–mass spectrometry

A robotic method has been established for the determination of bromate in sea water and drinking deep-sea water. Bromate in water was converted into volatile derivative, which was measured with headspace solid-phase micro extraction and gas chromatography–mass spectrometry (HS-SPME GC–MS). Derivatization reagent and the HS-SPME parameters (selection of fibre, extraction/derivatization temperature, heating time and; the morality of HCl) were optimized and selected. Under the established conditions, the detection and the quantification limits were 0.016 μg L⁻¹ and 0.051 μg L⁻¹, respectively, and the intra- and inter-day relative standard deviation was less than 7% at concentrations of 1.0 and 10.0 μg L⁻¹. The calibration curve showed good linearity with r² = 0.9998. The common ions Cl⁻, NO₃⁻, SO₄²⁻, HPO₄²⁻, H₂PO₄⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺ and Fe²⁺ did not interfere even when present in 1000-fold excess over the active species. The method was successfully applied to the determination of bromate in sea water and drinking deep-sea water.     

Sensitive determination of hydrazine in water by gas chromatography–mass spectrometry after derivatization with ortho-phthalaldehyde

A gas chromatography–mass spectrometric (GC–MS) method has been established for the determination of hydrazine in drinking water and surface water. This method is based on the derivatization of hydrazine with ortho-phthalaldehyde (OPA) in water. The following optimum reaction conditions were established: reagent dosage, 40 mg mL⁻¹ of OPA; pH 2; reaction for 20 min at 70 °C. The organic derivative was extracted with methylene chloride and then measured by GC–MS. Under the established condition, the detection and the quantification limits were 0.002 μg L⁻¹ and 0.007 μg L⁻¹ by using 5.0-mL of surface water or drinking water, respectively. The calibration curve showed good linearity with r² = 0.9991 (for working range of 0.05–100 μg L⁻¹) and the accuracy was in a range of 95–106%, and the precision of the assay was less than 13% in water. Hydrazine was detected in a concentration range of 0.05–0.14 μg L⁻¹ in 2 samples of 10 raw drinking water samples and in a concentration range of 0.09–0.55 μg L⁻¹ in 4 samples of 10 treated drinking water samples.     

On-line metals preconcentration and simultaneous determination using cloud point extraction and inductively coupled plasma optical emission spectrometry in water samples

A new on-line cloud point extraction (CPE) system coupled to ICP-OES was designed for simultaneous extraction, preconcentration and determination of Cd²⁺, Co²⁺, Cr³⁺, Cu²⁺, Fe³⁺ and Mn²⁺ ions in water samples. This is based on the complexation of the metal ions with 1-(2-thenoyl)-3,3,3-trifluoraceton reagent (TTA) at pH 6.0 in the presence of non-ionic surfactant of Triton X-114. The micellar solution was heated above 60 °C and loaded through a column packed with cotton, which acts as a filter for retaining the analyte-entrapped surfactant-rich phase. Then the surfactant-rich phase was eluted using propanol:0.5 mol L⁻¹ nitric acid solution (75:25, v/v) at a flow rate of 3.0 mL min⁻¹ and directly introduced into the nebulizer of the ICP-OES. Several factors influencing the instrumental conditions and extraction were evaluated and optimized. Under the optimum conditions, the enhancement factors of the proposed method for target ions were between 42 and 97, the detection limits (DLs) were in the range of 0.1-2.2 μg L⁻¹. The relative standard deviations (R.S.D.s) at 100 μg L⁻¹ concentration levels of each ion were found to be less than 4.6%. Also, the calibration graphs were linear in the range of 0.5-100 μg L⁻¹ with the correlation coefficients within the range of 0.9948-0.9994.Finally, the developed method was successfully applied to the extraction and determination of the mentioned metal ions in the tap, well, sea and mineral water samples and satisfactory results were obtained.     

Determination of cadmium in alcohol fuel using Moringa oleifera seeds as a biosorbent in an on-line system coupled to FAAS

In this study a new method for determination of cadmium in alcohol fuel using Moringa oleifera seeds as a biosorbent in an on-line preconcentration system coupled to flame atomic absorption spectrometry (FAAS) was developed. Flow and chemical variables of the proposed system were optimized through multivariate designs. The limit of detection for cadmium was 5.50 μg L⁻¹ and the precision was below 2.3% (35.0 μg L⁻¹, n = 9). The analytical curve was linear from 5 to 150 μg L⁻¹, with a correlation coefficient of 0.9993. The developed method was successfully applied to spiked alcohol fuel, and accuracy was assessed through recovery tests, with recovery ranging from 97.50 to 100%.     

Flow injection determination of aluminium by spectrofluorimetric detection after complexation with N-o-vanillidine-2-amino-p-cresol: the application to natural waters

An on-line flow injection spectrofluorimetric method for the direct determination of aluminium in water samples is described. The method is based on the reaction of aluminium with N-o-vanillidine-2-amino-p-cresol (OVAC) in acidic medium at pH 4.0 to form a water-soluble complex. The excitation and emission wavelengths were 423.0 and 553.0 nm, respectively, at which the OVAC-Al complex gave the maximum fluorescence intensity at pH 4.0 in a 50% methanol-50% water medium at 50 °C. An interference from fluoride ions was minimised by the addition of Be²⁺. Other ions were found not to interfere at the concentrations likely to be found in natural waters. The proposed methods were validated in terms of linearity, repeatability, detection limit, accuracy and selectivity. Under these conditions, the calibration was linear up to 1000 μg L⁻¹ (r = 0.999). The limit of detection (3σ) for the determination of Al(III) was 0.057 μg L⁻¹ and the precision for multiple determinations of 3 ng mL⁻¹ Al(III) prepared in ultra-pure water was found to be 0.62% (n = 10).The Schiff base ligand could be used to determine ultra-trace aluminium from natural waters. Analysis of environmental certified reference materials showed good agreement with the certified values. The procedure was found to be equally applicable to both freshwater and saline solutions, including seawater.     

Ultrasensitive and simultaneous detection of heavy metal ions based on three-dimensional graphene-carbon nanotubes hybrid electrode materials

A green and facile method was developed to prepare a novel hybrid nanocomposite that consisted of one-dimensional multi-walled carbon nanotubes (MWCNTs) and two-dimensional graphene oxide (GO) sheets. The as-prepared three-dimensional GO–MWCNTs hybrid nanocomposites exhibit excellent water-solubility owing to the high hydrophilicity of GO components; meanwhile, a certain amount of MWCNTs loaded on the surface of GO sheets through π–π interaction seem to be “dissolved” in water. Moreover, the graphene(G)-MWCNTs nanocomposites with excellent conductivity were obtained conveniently by the direct electrochemical reduction of GO–MWCNTs nanocomposites. Seeing that there is a good synergistic effect between MWCNTs and graphene components in enhancing preconcentration efficiency of metal ions and accelerating electron transfer rate at G-MWCNTs/electrolyte interface, the G-MWCNTs nanocomposites possess fast, simultaneous and sensitive detection performance for trace amounts of heavy metal ions. The electrochemical results demonstrate that the G-MWCNTs nanocomposites can act as a kind of practical sensing material to simultaneously determine Pb²⁺ and Cd²⁺ ions in terms of anodic stripping voltammetry (ASV). The linear calibration plots for Pb²⁺ and Cd²⁺ ranged from 0.5 μg L⁻¹ to 30 μg L⁻¹. The detection limits were determined to be 0.2 μg L⁻¹ (S/N = 3) for Pb²⁺ and 0.1 μg L⁻¹ (S/N = 3) for Cd²⁺ in the case of a deposition time of 180 s. It is worth mentioning that the G-MWCNTs modified electrodes were successfully applied to the simultaneous detection of Cd²⁺ and Pb²⁺ ions in real electroplating effluent samples containing lots of surface active impurities, showing a good application prospect in the determination of trace amounts of heavy metals.     

Fabrication and characterization of hexahistidine-tagged protein functionalized multi-walled carbon nanotubes for selective solid-phase extraction of Cu and Ni

Hexahistidine-tagged protein functionalized multi-walled carbon nanotubes (MWCNTs/6His-tagged protein) were prepared and characterized by ultraviolet-visible spectrophotometry and atomic force microscopy. Both static and dynamical adsorption experiments showed that the MWCNTs/6His-tagged protein served as good sorbent for the solid-phase extraction of Cu²⁺ and Ni²⁺. Effective on-line sorption of Cu²⁺ and Ni²⁺ on the MWCNTs/6His-tagged protein packed microcolumn was achieved in a pH range of 3.0-4.5 and 4.5-6.0, respectively. The retained Cu²⁺ and Ni²⁺ were efficiently eluted with 0.2 mol L⁻¹ imidazole-HCl solution for on-line flame atomic absorption spectrometric determination. The MWCNTs/6His-tagged protein exhibited fairly fast kinetics for the sorption of Cu²⁺ and Ni²⁺, and offered up to 20,000 and 1800 times improvement in the tolerable concentrations of co-existing ions over the MWCNTs for solid-phase extraction of Cu²⁺ and Ni²⁺, respectively. On-line solid-phase extraction at a flow rate of 5.0 mL min⁻¹ for 60 s gave an enhancement factor of 29 for Cu²⁺ and 28 for Ni²⁺, a sample throughput of 45 h⁻¹, and a detection limit (3s) of 0.31 μg L⁻¹ for Cu²⁺ and 0.63 μg L⁻¹ for Ni²⁺. The precision for 11 replicate measurements was 2.4% for 10 μg L⁻¹ Cu²⁺, and 2.5% for 15 μg L⁻¹ Ni²⁺.     

Preconcentration of trace elements from water samples on a minicolumn of yeast (Yamadazyma spartinae) immobilized TiO2 nanoparticles for determination by ICP-AES

A trace element preconcentration procedure is described utilizing a minicolumn of yeast (Yamadazyma spartinae) immobilized TiO₂ nanoparticles for determination of Cr, Cu, Fe, Mn, Ni and Zn from water samples by inductively coupled plasma atomic emission spectrometry. The elements were quantitatively retained on the column between pH 6 and 8. Elution was made with 5% (v/v) HNO₃ solution. Recoveries ranged from 98 ± 2 (Cr) to 100 ± 4 (Zn) for preconcentration of 50 mL multielement solution (50 μg L⁻¹). The column made up of 100 mg sorbent (yeast immobilized TiO₂ NP) offers a capacity to preconcentrate up to 500 mL of sample solution to achieve an enrichment factor of 250 with 2 mL of 5% (v/v) HNO₃ eluent. The detection limits obtained from preconcentration of 50 mL blank solutions (5%, v/v, HNO₃, n = 11) were 0.17, 0.45, 0.25, 0.15, 0.33 and 0.10 μg L⁻¹ for Cr, Cu, Fe, Mn, Ni and Zn, respectively. Relative standard deviation (RSD) for five replicate analyses was better than 5%. The retention of the elements was not affected from up to 500 μg L⁻¹ Na⁺ and K⁺ (as chlorides), 100 μg L⁻¹ Ca²⁺ (as nitrate) and 50 μg L⁻¹ Mg²⁺ (as sulfate). The method was validated by analysis of freshwater standard reference material (SRM 1643e) and applied to the determination of the elements from tap water and lake water samples.     

Improvement of sensitivity in flow analysis by exploiting a multi-reversed software-assisted system

A multi-reversed flow system software-assisted was developed for improvement of sensitivity in flow analysis. The performance of the flow system proposed was evaluated by using as a model the conventional Griess’ colorimetric reaction for determination of nitrite in waters. The manifold incorporated three 3-way solenoid valves, a relay box solenoid actuated, a peristaltic pump, and a photometric detector. A tailored software was designed and written in Visual Basic 6.0 which allows full control of all flow system components and simultaneous acquisition and processing of the data. The sensitivity measured as the slope of the calibration curve was improved 2.5- and 1.4-fold regarding those obtained by continuous- and stopped-flow systems, respectively. Other valuable features such as analytical throughput of 55 determinations per hour, limit of detection of 5 μg L⁻¹ (3σ_blank/slope), relative standard deviation < 2% (n = 8), and a linear dynamic range up to 1800 μg L⁻¹ were also achieved.     

Synthesis of three haptens for the class-specific immunoassay of O,O-dimethyl organophosphorus pesticides and effect of hapten heterology on immunoassay sensitivity

A general and broad class-specific enzyme-linked immunosorbent assay was developed for the O,O-dimethyl organophosphorus pesticides, including malathion, dimethoate, phenthoate, phosmet, methidathion, fenitrothion, methyl parathion and fenthion. Three haptens with different spacer-arms were synthesized. The haptens were conjugated to bovine serum albumin (BSA) for immunogens and to ovalbumin (OVA) for coating antigens. Rabbits were immunized with the immunogens and six polyclonal antisera were produced and screened against each of the coating antigens using competitive indirect enzyme-linked immunosorbent assay for selecting the proper antiserum. The effect of hapten heterology on immunoassay sensitivity was also studied. The antibody-antigen combination with the most selectivity for malathion was further optimized and tested for tolerance to co-solvent, pH and ionic strength changes. The IC₅₀ values, under optimum conditions, were estimated to be 30.1 μg L⁻¹for malathion, 28.9 μg L⁻¹ for dimethoate, 88.3 μg L⁻¹ for phenthoate, 159.7 μg L⁻¹ for phosmet, 191.7 μg L⁻¹ for methidathion, 324.0 μg L⁻¹ for fenitrothion, 483.9 μg L⁻¹ for methyl parathion, and 788.9 μg L⁻¹ for fenthion. Recoveries of malathion, dimethoate, phenthoate, phosmet and methidathion from fortified Chinese cabbage samples ranged between 77.1% and 104.7%. This assay can be used in monitoring studies for the multi-residue determination of O,O-dimethyl organophosphorus pesticides.     

High-sensitivity determination of lead and cadmium based on the Nafion-graphene composite film

Graphene nanosheets, dispersed in Nafion (Nafion-G) solution, were used in combination with in situ plated bismuth film electrode for fabricating the enhanced electrochemical sensing platform to determine the lead (Pb²⁺) and cadmium (Cd²⁺) by differential pulse anodic stripping voltammetry (DPASV). The electrochemical properties of the composite film modified glassy carbon electrode were investigated. It is found that the prepared Nafion-G composite film not only exhibited improved sensitivity for the metal ion detections, but also alleviated the interferences due to the synergistic effect of graphene nanosheets and Nafion. The linear calibration curves ranged from 0.5 μg L⁻¹ to 50 μg L⁻¹ for Pb²⁺ and 1.5 μg L⁻¹ to 30 μg L⁻¹ for Cd²⁺, respectively. The detection limits (S/N = 3) were estimated to be around 0.02 μg L⁻¹ for Pb²⁺ and Cd²⁺. The practical application of the proposed method was verified in the water sample determination.     

A compact portable flow analysis system for the rapid determination of total phosphorus in estuarine and marine waters

The development and evaluation of a portable flow analysis system for the in situ determination of total phosphorus is described. The system has been designed with rapid underway monitoring in mind. The system employs an ultra-violet photo-reactor and thermal heating for peroxodisulfate digestion of total phosphorus to orthophosphate, followed by spectrophotometric detection with a multi-reflective flow cell and low-power light emitting diode using the molybdenum blue method. Reagents are stored under gas pressure and delivered using software controlled miniature solenoid valves. The fully automated system has a throughput of 115 measurements per hour, a detection limit of 1 μg P L⁻¹, and gives a linear response over the calibration range of 0-200 μg P L⁻¹ (r² = 0.9998), with a precision of 4.6% RSD at 100 μg P L⁻¹ (n = 10). Field validation of the instrument and method was performed in Port Philip and Western Port Bays in Victoria, SE Australia, where 2499 analyses were performed over a 25 h period, over a cruise path of 285 km. Good agreement was observed between determinations of samples taken manually and analysed in the laboratory and those measured in situ with the flow analysis system.     

Speciation of dissolved Fe(II) and Fe(III) in environmental water samples by micro-column packed with N-benzoyl-N-phenylhydroxylamine loaded on microcrystalline naphthalene and determination by electrothermal vaporization inductively coupled plasma-optical emission spectrometry

A novel solid phase extraction technique for the speciation of trace dissolved Fe(II) and Fe(III) in environmental water samples was developed by coupling micro-column packed with N-benzoyl-N-phenylhydroxylamine (BPHA) loaded on microcrystalline naphthalene to electrothermal vaporization inductively coupled plasma-optical emission spectrometry (ETV-ICP-OES). Various influencing factors on the separation and preconcentration of Fe(II) and Fe(III), such as the acidity of the aqueous solution, sample flow rate and volume, have been investigated systematically, and the optimized operation conditions were established. At pH 3.0 Fe(III) could be selectively retained by micro-column (20 mm × 1.4 mm, i.d.) packed with BPHA immobilized on microcrystalline naphthalene, and Fe(II) passed through the micro-column. Both Fe(II) and Fe(III) could be adsorbed by the micro-column at pH 6.5. Thus, the total Fe could be determined without the need for preoxidation of Fe(II) to Fe(III). The retained Fe(III) or the Fe(II) and Fe(III) was subsequently eluted by 0.1 ml of 1 mol l⁻¹ HCl. The adsorption capacity of the solid phase adsorption material was found to be 45.0 mg g⁻¹ for Fe(III) at pH 3.0 and 65.3 mg g⁻¹ for Fe(II) at pH 6.5, respectively. The detection limit (3σ) of 0.053 μg l⁻¹ was obtained with a practical enrichment factor of 156 at a sample volume of 17 ml. The relative standard deviations of 4.2% and 4.6% (C_Fe(III) = C_Fe(II) = 10 μg l⁻¹, n = 7) for Fe(III) and total iron were found, respectively. The method was successfully applied to the determination of trace Fe(II) and Fe(III) in environmental water samples (East Lake water, local tap water and mineral water). In order to validate the method, the developed method was applied to the determination of total iron in certified materials of NIES NO.10-b rice flour and GBW07605 tea leaves, and the results obtained were in good agreement with the certified values.     

The use of a polymer inclusion membrane for separation and preconcentration of orthophosphate in flow analysis

A highly sensitive flow analysis system has been developed for the trace determination of reactive phosphate in natural waters, which uses a polymer inclusion membrane (PIM) with Aliquat 336 as the carrier for on-line analyte separation and preconcentration. The system operates under flow injection (FI) and continuous flow (CF) conditions. Under optimal FI conditions the system is characterised by a linear concentration range between 0.5 and 1000 μg L⁻¹ P, a sampling rate of 10 h⁻¹, a limit of detection of 0.5 μg L⁻¹ P and RSDs of 3.2% (n = 10, 100 μg L⁻¹) and 7.7% (n = 10, 10 μg L⁻¹). Under CF conditions with 10 min stop-flow time and sample solution flow rate of 1.32 mL min⁻¹ the flow system offers a limit of detection of 0.04 μg L⁻¹ P, a sampling rate of 5 h⁻¹ and an RSD of 3.4% (n = 5, 2.0 μg L⁻¹). Interference studies revealed that anions commonly found in natural waters did not interfere when in excess of at least one order of magnitude. The flow system, operating under CF conditions, was successfully applied to the analysis of natural water samples containing concentrations of phosphate in the low μg L⁻¹ P range, using the multipoint standard addition method.     

Novel catalytic oxidative coupling reaction of N,N-dimethyl-p-phenylenediamine with 1,3-phenylenediamine and its applications to the determination of copper and iron at trace levels by flow injection technique

A new catalytic oxidative coupling reaction of N,N-dimethyl-p-phenylenediamine (DPD) with 1,3-phenylenediamine (mPD) in the presence of hydrogen peroxide has been developed for trace metals analysis. The rate of the oxidation/coupling reaction can be enhanced significantly by iron, copper and cobalt. These metal ions can catalyze the oxidation reaction of DPD to form an oxidized product; the oxidized DPD was then coupled with mPD to give a blue-colored product which was measured spectrophotometrically at 650 nm. On the basis of such a reaction scheme, two simple flow injection analysis methods for the determination of copper and iron have been developed. Detailed studies on chemical and FIA variables affecting the sensitivity of the detection were carried out. Interferences from several ionic species were examined for the determination of copper: the interference effect by Fe(III) and Fe(II) up to 1.5 mg L⁻¹ was successfully suppressed by pretreating sample with ammonium acetate buffer solution (pH 8.4). Good linearity of a standard calibration graph was obtained over the ranges of 0-8 and 0-2 μg L⁻¹ of copper and iron, respectively, and the detection limits were 0.05 and 0.02 μg L⁻¹ for copper and iron, respectively. The precision of the methods in terms of relative standard deviation were 1.4 and 1.5% of R.S.D. which were obtained from 10 injections of 2.0 and 1.0 μg L⁻¹ of standard copper and iron, respectively. The proposed methods were successfully applied to the determination of copper and iron in tap and river water samples. The accuracy of the proposed methods was assessed by the analysis of certified reference material of river water.     

Determination of bisphenol A, 4-n-nonylphenol, and 4-tert-octylphenol by temperature-controlled ionic liquid dispersive liquid-phase microextraction combined with high performance liquid chromatography-fluorescence detector

Present study described a simple, sensitive, and viable method for the determination of bisphenol A, 4-n-nonylphenol and 4-tert-octylphenol in water samples using temperature-controlled ionic liquid dispersive liquid-phase microextraction coupled to high performance liquid chromatography-fluorescence detector. In this experiment, 1-octyl-3-methylimidazolium hexafluorophosphate ([C₈MIM][PF₆]) was used as the extraction solvent, and bisphenol A, 4-n-nonylphenol and 4-tert-octylphenol were selected as the model analytes. Parameters affecting the extraction efficiency such as the volume of [C₈MIM][PF₆], dissolving temperature, extraction time, sample pH, centrifuging time and salting-out effect have been investigated in detail. Under the optimized conditions, good linear relationship was found in the concentration range of 1.0-100 μg L⁻¹ for BPA, 1.5-150 μg L⁻¹ for 4-NP, and 3-300 μg L⁻¹ for 4-OP, respectively. Limits of detection (LOD, S/N = 3) were in the range of 0.23-0.48 μg L⁻¹. Intra day and inter day precisions (RSDs, n = 6) were in the range of 4.6-5.5% and 8.5-13.3%, respectively. This method has been also successfully applied to analyze the real water samples at two different spiked concentrations and excellent results were obtained.     

Headspace liquid-phase microextraction using ionic liquid as extractant for the preconcentration of dichlorodiphenyltrichloroethane and its metabolites at trace levels in water samples

A novel technique, high temperature headspace liquid-phase microextraction (HS-LPME) with room temperature ionic liquid (RTIL), 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄MIM][PF₆]) as extractant, was developed for the analysis of dichlorodiphenyltrichloroethane (p,p′-DDT and o,p′-DDT) and its metabolites including 4,4′-dichlorodiphenyldichloroethylene (p,p′-DDE) and 4,4′-dichlorodiphenyldichloroethane (p,p′-DDD) in water samples by high performance liquid chromatography with ultraviolet detection. The parameters such as salt content, sample pH and temperature, stirring rate, extraction time, microdrop volume, and sample volume, were found to have significant influence on the HS-LPME. The conditions optimized for extraction of target compounds were as follows: 35% NaCl (w/v), neutral pH condition, 70 °C, 800 rpm, 30 min, 10 μL [C₄MIM][PF₆], and 25 mL sample solutions. Under the optimized conditions, the linear range, detection limit (S/N = 3), and precision (R.S.D., n = 6) were 0.3-30 μg L⁻¹, 0.07 μg L⁻¹, and 8.0% for p,p′-DDD, 0.3-30 μg L⁻¹, 0.08 μg L⁻¹, and 7.1% for p,p′-DDT, 0.3-30 μg L⁻¹, 0.08 μg L⁻¹, and 7.2% for o,p′-DDT, and 0.2-30 μg L⁻¹, 0.05 μg L⁻¹, and 6.8% for p,p′-DDE, respectively. Water samples including tap water, well water, snow water, reservoir water, and wastewater were analyzed by the proposed procedure and the recoveries at 5 μg L⁻¹ spiked level were in the range of 86.8-102.6%.