Simultaneous titration of ternary alkaline-earth mixtures employing a potentiometric electronic tongue

A fast novel complexometric titration procedure is proposed, in which equivalence concentrations were determined using a potentiometric electronic tongue. The titration consists in a reduced number of fixed additions of titrant and the recording of the potentials of an array of ion-selective electrodes with cross-selectivity response. The generated data (number of sensors × number of additions) were used as input data to an artificial neural network response model previously trained with standards. The application of this procedure is demonstrated with automated EDTA titrations of Ca²⁺, Mg²⁺ and Sr²⁺ mixtures, up to 3.3 mM total ion concentration. In the studied case, good results predicting the three concentrations were obtained using five 1 mL fixed volume additions plus the readings of eight sensors. The unique additional step required was the pH buffering of the sample to pH 9.5. Good comparisons were observed between obtained and expected concentrations for the three cations with the external validation samples (n = 17, with RMSE values of 0.18, 0.28 and 0.32 mM for Ca²⁺, Mg²⁺ and Sr²⁺, respectively). The proposed procedure was applied to mineral waters and compared with reference methods.     

Planar potentiometric sensors based on Au and Ag microelectrodes and conducting polymers for flow-cell analysis

Back-side contact Au and Ag microelectrodes were used as transducers to construct planar all-solid-state electrodes suitable for flow-through analysis. The microsensors were based on plasticized PVC potassium-selective membranes containing ion-electron conducting polymer—polypyrrole doped with di(2-ethylhexyl) sulfosuccinate. The proposed technique allowed simple construction of microsensors in one step, by membrane solution casting directly on the surface of the planar metallic transducers. The performance of the microsensors based on Au and Ag transducers were determined and compared with planar sensors based on internal electrolyte immobilized in polyHEMA. The addition of the polypyrrole to the membrane composition did not influence on the selectivity, reproducibility and long-term stability of the microsensors but improved their standard potential stability in time in comparison with coated-wire type sensors. Moreover, all-solid-state microsensors based on Au transducers exhibited better signal stability than Ag based sensors.     

Approaches to the liquid chromatographic determination of carboxylic acids using potentiometric detection with a metallic copper electrode

Summary A metallic copper electrode is evaluated as a potentiometric detector for carboxylic acids. The application of this device to ion-exchange chromatography is illustrated by the determination of oxalate in urine. Oxalate was selectively detected in the presence of a 100-fold excess of sulphate after separation on a low-capacity methacrylate anion-exchange column using 0.7mM potassium hydrogen phthalate at pH 7.1 as eluent. Calibration plots were linear up to 50ppm of oxalate. Potentiometric detection has also been applied to ion-exclusion chromatography using 0.005% phosphoric acid as eluent. With this method detection limits of 0.2, 2.1, 5.0 and 5.3μg were obtained for formic, acetic, propionic and iso-butyric acids, respectively.     

Poly(vinyl chloride) membrane electrode for the determination of verapamil

A verapamil-PVC membrane ion-selective electrode based on the verapamil-reineckate ion pair was prepared with dibutyl phthalate as a plasticizer. The electrode exhibited a linear response with a Nernstian slope (52.8 mV decade^?1 at 20° C) for verapamil concentrations of 10^?5?10^?2M over the pH range 3–7. The electrode also exhibited very good selectivity for verapamil with respect to various inorganic and organic cations. Gran II linear titration and potentiometric titration were used to determine verapamil in pure solution, with an average recovery of 99.3% and a relative standard deviation of 0.4%.     

Determination of total fluoride in HF/HNO3/H2SiF6 etch solutions by new potentiometric titration methods

In the photovoltaic industry the etching of silicon in HF/HNO₃ solutions is a decisive process for cleaning wafer surfaces or to produce certain surface morphologies like polishing or texturization. With regard to cost efficiency, a maximal utilisation of etch baths in combination with highest quality and accuracy is strived. To provide an etch bath control realised by a replenishment with concentrated acids the main constituents of these HF/HNO₃ etch solutions including the reaction product H₂SiF₆ have to be analysed. Two new methods for the determination of the total fluoride content in an acidic etch solution based on the precipitation titration with La(NO₃)₃ are presented within this paper. The first method bases on the proper choice of the reaction conditions, since free fluoride ions have to be liberated from HF and H₂SiF₆ at the same time to be detected by a fluoride ion-selective electrode (F-ISE). Therefore, the sample is adjusted to a pH of 8 for total cleavage of the SiF₆²⁻ anion and titrated in absence of buffers. In a second method, the titration with La(NO₃)₃ is followed by a change of the pH-value using a HF resistant glass-electrode. Both methods provide consistent values, whereas the analysis is fast and accurate, and thus, applicable for industrial process control.     

Simultaneous potentiometric determination of cationic and ethoxylated nonionic surfactants in liquid cleaners and disinfectants

A sensitive potentiometric surfactant sensor based on a highly lipophilic 1,3-didecyl-2-methyl-imidazolium cation and a tetraphenylborate (TPB) antagonist ion was used as the end-point detector in ion-pair potentiometric surfactant titrations using sodium TPB as a titrant. Several analytical and technical grade cationic and ethoxylated nonionic surfactants (EONS) and mixtures of both were potentiometrically titrated.The sensor showed satisfactory analytical performances within a pH range of 3-10 and exhibited satisfactory selectivity for all CS and EONS investigated. Ionic strength did not influence the titration except at 0.1 M NaCl, in which a slight distortion of the second inflexion corresponded with the nonionic surfactant.Two-component combinations of four CS and three EONS were potentiometrically titrated using the sensor previously mentioned as the end-point detector. The quantities of the surfactants varied between 2 and 6 μmol for CS and 2.50 and 7.50 μmol for EONS. The known addition methodology was used for determination of the surfactant with considerably lower concentration in the mixture.Three commercial products containing cationic surfactants as disinfectants and nonionic surfactants were potentiometrically titrated, and the results for both type of surfactants were compared with those obtained with standard conventional methods.     

The determination of reducing carbohydrates using a cation-exchange column and potentiometric detection with a metallic copper electrode

Summary A metallic copper electrode is employed as a potentiometric detector for reducing carbohydrates after their separation on a cation-exchange column. A post-column reactant solution comprising 1 mM copper (II) and 35 mM ammonia is mixed with the column effluent and the metallic copper electrode provides a steady baseline potential by responding in a Nernstian manner to the level of copper ions present. This in turn is affected by the presence of eluted reducing carbohydrates, leading to an indirect detection method for these species. The method is applied to the detection of maltose, lactose, xylose, glucose, sorbose, fructose and arabinose. The electrode response mechanism is discussed and detection limits in the low nanomole range are reported. The potentiometric detector is shown to be more sensitive than refractive index detection.     

Development of a novel potentiometric titration method for determination of polypropylene degradation

In this study, a novel potentiometric titration of hydroperoxide in degraded polypropylene (PP) is proposed. This titration is quite sensitive compared with the conventional ones such as UV and manual titrations, and its detection limit was about 2 meq/kg. The sensitivity was equal to that of molecular weight measurement by GPC for the degraded PP and, in addition, the volatilization behavior of the hydroperoxide could be detected. This titration was found to be very effective for the determination of PP degradation.     

A miniaturized and integrated galvanic cell for the potentiometric measurement of ions in biological liquids

A procedure for an all-plastic electrochemical cell comprising miniaturized planar indicator and reference electrodes is described. All electrodes are based on conducting polymers, are fully integrated, and contain no internal electrolyte. The reference microsensors were deposited via electrochemical polymerization from a water solution containing the monomer 3,4-ethylenedioxythiophene (EDOT) or 1-methylpyrrole (MPy) and a biochemical buffer 3-(N-morpholino) propanesulfonic acid [MOPS], 2-(N-morpholino) ethanesulfonic acid [MES], or 2-hydroxy-5-sulfobenzoic acid [SSA]). Ion-sensitive microelectrodes were prepared by the deposition of the ion-sensitive membrane solution (Ca²⁺, K⁺, and Cl⁻) directly onto the mediating poly-EDOT (PEDOT), PEDOT–SSA, PEDOT–MES, PEDOT–MOPS, or poly-MPy–MOPS layers.     

An initial-rate potentiometric method for the determination of uric acid using a fluoride ion-selective electrode

The principle of a general potentiometric method based on Emerson-Trinder reaction for the assay of various hydrogen peroxide generating systems is reported. Emerson-Trinder reaction, habitually employed as a spectrophotometric indicator reaction, is exploited in this method as a potentiometric indicator reaction. This method is based on the detection of F⁻ ions, liberated from the oxidation of a fluorophenol compound used as hydrogen-donor in Emerson-Trinder reaction, by a fluoride ion-selective electrode. The ability and usefulness of this method are illustrated by an initial-rate potentiometric determination of uric acid in aqueous and human serum samples, for which, initial-rate reaction progress curves, linear calibration curve, within-day precisions, upper and lower detection limits, and also its analytical recovery were reported.     

Molecularly imprinted polymer based potentiometric sensor for the determination of hydroxyzine in tablets and biological fluids

Molecular imprinting is a useful technique for the preparation of functional materials with molecular recognition properties. In this work, a biomimetic potentiometric sensor, based on a non-covalent imprinted polymer, was fabricated for the recognition and determination of hydroxyzine in tablets and biological fluids. The molecularly imprinted polymer (MIP) was synthesized by precipitation polymerization, using hydroxyzine dihydrochloride as a template molecule, methacrylic acid (MAA) as a functional monomer and ethylene glycol dimethacrylat (EGDMA) as a cross-linking agent. The sensor showed a high selectivity and a sensitive response to the template in aqueous system. The MIP-modified electrode exhibited a Nernstian response (29.4 ± 1.0 mV decade⁻¹) in a wide concentration range of 1.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a lower detection limit of 7.0 × 10⁻⁷ M. The electrode demonstrated a response time of ∼15 s, a high performance and a satisfactory long-term stability (more than 5 months). The method has the requisite accuracy, sensitivity and precision to assay hydroxyzine in tablets and biological fluids.     

New flow injection potentiometric graphite coated ion-selective electrode for the determination of VO ions

A new coated ion-selective electrode for the determination of trace vanadyl ions (VO²⁺) by flow injection potentiometry (FIP) with a home-made flow cell has been developed. The PVC-based membrane was coated on a graphite electrode with an effective area of 4.90 mm². The optimum membrane contains 5 wt.% 1,8-diaminonaphtalene as ionophore, 35 wt.% plasticizer 2-nitrophenyl octyl ether, 55 wt.% PVC and 5 wt.% additive potassium tetrakis (p-chlorophenyl) borate. The electrode in flow injection potentiometry resulted in well defined peaks for vanadyl ions with a very high sampling rate (180 injections/h). Linear calibration was obtained from 1.14×10⁻⁷ to 1.14×10⁻¹ M vanadyl ions, with a slope of 28.3±0.3 mV per decade change in vanadyl concentration, and very low detection limit of 1.14×10⁻⁷ M and the electrode can be used for at least 1 months without any considerable change in potential response. Selectivity coefficients for several ions were obtained by the matched potential method with respect VO²⁺ ions. The flow cell is simple to construct and free from memory effect problems over long periods of use. The sensor was used for the recovery of trace VO²⁺ ions from tap water and the determination of VO²⁺ in synthetic sample.     

On the liquid junction potential for the determination of equilibrium constants by means of the potentiometric technique without constant ionic strength

A modified method for the calculation of liquid junction potentials based on the Henderson equation is proposed. The estimation of the activity coefficients and the conductivities is performed by means of the Modified Bromley Methodology [G. Borge, R. Castaño, M.P. Carril, M.S. Corbillón, J.M. Madariaga, Fluid Phase Equilibria 121 (1996) 85–98;G. Borge, N. Etxebarria, L.A. Fernández, M.A. Olazabal, J.M. Madariaga, Fluid Phase Equilibria 121 (1996) 99–109.] and the Extended Falkenhagen Equation [A. De Diego, Conductivity of concentrated electrolytic solutions: study of the dependence with concentration and temperature, Ph.D. Thesis, University of the Basque Country, Bilbao, 1996.]. The efficiency of the method has been tested in potentiometric titrations without constant ionic strength. Its applicability to potentiometric titrations with constant ionic strength is also discussed.     

Use of organofunctionalized nanoporous silica gel to improve the lifetime of carbon paste electrode for determination of copper(II) ions

A new functionalized nanoporous silica gel with dipyridyl group (DPNSG) was synthesized. Then, the potentiometric response of the copper(II) ion was investigated at a carbon paste electrode chemically modified with this newly designed functionalized nanoporous silica gel. The electrodes with DPNSG proportions of 15.0% (w/w) demonstrated very stable potentials. Calibration plots with Nernstian slopes for Cu²⁺ were observed, 28.4 (±1.0) mV decade⁻¹, over a wide linear concentration range (1.0 × 10⁻⁷ to 1.0 × 10⁻² M). The electrode exhibited a detection limit of 8.0 × 10⁻⁸ M. Moreover, the selectivity coefficients measured by the match potential method in acetate buffer, pH 5.5, were investigated. The electrode presented a response time of ∼50 s, high performance, high sensitivity in a wide range of cation activities and good long-term stability (more than 9 months). The method was satisfactory and was used to determine the copper ion concentration in waste waters, contaminated by this metal.     

Macrocyclic antibiotics as chiral selectors in the design of enantioselective, potentiometric membrane electrodes for the determination of S-flurbiprofen

Construction of three novel enantioselective, potentiometric membrane electrodes based on carbon paste impregnated with different macrocyclic antibiotics vancomycin and teicoplanin as chiral selectors are described. The solutions for the construction of electrodes were prepared in phosphate buffer pH 4 for the vancomycin-based electrode (VCM), pH 6 and pH 6/40% acetonitrile solutions for teicoplanin-based electrodes, TCP I and II, respectively. The proposed electrodes were applied in the assay of S-flurbiprofen raw material and its pharmaceutical formulation by use of direct potentiometry, VCM electrode exhibiting the best enantioselectivity. The surfaces of the electrodes are easily renewable by simply polishing on an alumina paper.     

Application of artificial neural network to simultaneous potentiometric determination of silver(I), mercury(II) and copper(II) ions by an unmodified carbon paste electrode

The response characteristics and selectivity coefficients of an unmodified carbon paste electrode (CPEs) towards Ag⁺, Cu²⁺ and Hg²⁺ were evaluated. The electrode was used as an indicator electrode for the simultaneous determination of the three metal ions in their mixtures via potentiometric titration with a standard thiocyanate solution. A three-layered feed-forward artificial neural network (ANN) trained by back-propagation learning algorithm was used to model the complex non-linear relationship between the concentration of silver, copper and mercury in their different mixtures and the potential of solution at different volumes of the added titrant. The network architecture and parameters were optimized to give low prediction errors. The optimized networks were able to precisely predict the concentrations of the three cations in synthetic mixtures.     

以锑电极作参比电极测定废水中硫化物

提出了以锑电极作为参比电极与Ag2 S电极组成无液接测量电池测定废水中硫化物的新方法。并研究了电极的性能 ,测定条件及干扰物质的影响。方法的线性范围 1 .0× 1 0 - 2 mol/L～ 5 .0× 1 0 - 7mol/L[S2 - ],回收率为 99%～1 0 3%     

Chemical analysis of acidic silicon etch solutions: I. Titrimetric determination of HNO3, HF, and H2SiF6

The chemical etching of silicon using HF-HNO₃ mixtures is a widely used process in the processing of silicon wafers for microelectronic or photovoltaic applications. The control of the etch bath composition is the necessary condition for an effective bath utilization, for the replenishment of the consumed acids, and to maintain a certain etch rate. The present paper describes two methods for the total analysis of the individual etch bath constituents HF, HNO₃, and H₂SiF₆. Both methods start with an aqueous acid-base titration determining the total acid concentration and the concentration of H₂SiF₆. The first method is an acid-base titration using a 0.1 mol L⁻¹ methanolic solution of cyclohexylamine (CHA) as non-aqueous titrant to determine the content of nitric acid. Then, the amount of hydrofluoric acid is calculated from the difference between the total acid and nitric acid content. The second method is based on the determination of the total fluoride concentration using a fluoride ion-selective electrode (F-ISE). The content of hydrofluoric acid is obtained from the difference between the total fluoride content and the amount of fluoride bound as H₂SiF₆. The amount of nitric acid results finally calculated as difference to the total acid content.     

Application of 2‐(benzyliminomethyl)‐6‐methoxy‐4‐(4‐methoxyphenyl‐azo)phenol in construction of ion‐selective PVC membrane electrode for determination of copper (II) in mineral water sample

The potentiometric characteristics of a new Cu²⁺‐selective electrode based on 2‐(benzyliminomethyl)‐6‐methoxy‐4‐(4‐methoxyphenyl‐azo) phenol as an efficient ionophore has been evaluated. The effects of influential parameters on the potentiometric responses such as the amount of plasticizer, the amount of ionophore, pH of the sample solution, and the effect of coexisting ions on the electrode signal were subsequently investigated . The selectivity of the electrode was assessed by calculating the selectivity coefficients using the matched potential method. The optimum ratio of the amount of materials required for the preparation of the electrode was found to be 1.7: 32.1: 64.2: 2.0 corresponding to carboxylated PVC, dimethyl sebacate as solvent mediators, potassium tetrakis (p‐chlorophenyl) borate as the anion localizing agent, and ionophore, respectively. The electrode had a fast response (7s) as well as a satisfactory Nernstian slope (29.26±0.91 mV/decade) to Cu²⁺ over a wide concentration range of 2.0×10^?6‐ 5.0×10^?2 M with a low detection limit of 5.9×10^?7 M. The developed sensor was successfully used for the potentiometric titration of Cu²⁺ ion with EDTA and subsequently, efficient determination of this metal ion in a mineral water sample was performed.