Ferrofluid-based liquid-phase microextraction

A new mode of liquid-phase microextraction based on a ferrofluid has been developed. The ferrofluid was composed of silica-coated magnetic particles and 1-octanol as the extractant solvent. The 1-octanol was firmly confined within the silica-coated particles, preventing it from being lost during extraction. Sixteen polycyclic aromatic hydrocarbons (PAHs) were used as model compounds in the development and evaluation of the extraction procedure in combination with gas chromatography-mass spectrometry. Parameters affecting the extraction efficiency were investigated in detail. The optimal conditions were as follows: 20mL sample volume, 10mg of the silica-coated magnetic particles (28mg of ferrofluid), agitation at 20Hz, 20min extraction time, and 2min by sonication with 100μL acetonitrile as the final extraction solvent. Under optimal extraction conditions, enrichment factors ranging from 102- to 173-fold were obtained for the analytes. The limits of detection and the limits of quantification were in the range of 16.8 and 56.7pgmL(-1) and 0.06 and 0.19ngmL(-1), respectively. The linearities were between 0.5-100 and 1-100ngmL(-1) for different PAHs. As the ferrofluid can respond to and be attracted by a magnet, the extraction can be easily achieved by reciprocating movement of an external magnet that served to agitate the sample. No other devices were needed in this new approach of extraction. This new technique is affordable, efficient and convenient for microextraction, and offers portability for potential onsite extraction.     

A novel dispersive liquid-liquid microextraction based on solidification of floating organic droplet method for determination of polycyclic aromatic hydrocarbons in aqueous samples

A new dispersive liquid-liquid microextraction based on solidification of floating organic droplet method (DLLME-SFO) was developed for the determination of five kinds of polycyclic aromatic hydrocarbons (PAHs) in environmental water samples. In this method, no specific holder, such as the needle tip of microsyringe and the hollow fiber, is required for supporting the organic microdrop due to the using of organic solvent with low density and proper melting point. Furthermore, the extractant droplet can be collected easily by solidifying it in the lower temperature. 1-Dodecanol was chosen as extraction solvent in this work. A series of parameters that influence extraction were investigated systematically. Under optimal conditions, enrichment factors (EFs) for PAHs were in the range of 88-118. The limit of detections (LODs) for naphthalene, diphenyl, acenaphthene, anthracene and fluoranthene were 0.045, 0.86, 0.071, 1.1 and 0.66 ng mL⁻¹, respectively. Good reproducibility and recovery of the method were also obtained. Compared with the traditional liquid-phase microextraction (LPME) and dispersive liquid-liquid microextraction (DLLME) methods, the proposed method obtained about 2 times higher enrichment factor than those in LPME. Moreover, the solidification of floating organic solvent facilitated the phase transfer. And most importantly, it avoided using high-density and toxic solvent in the traditional DLLME method. The proposed method was successfully applied to determinate PAHs in the environmental water samples. The simple and low-cost method provides an alternative method for the analysis of non-polar compounds in complex environmental water.     

Screening method for phthalate esters in water using liquid-phase microextraction based on the solidification of a floating organic microdrop combined with gas chromatography-mass spectrometry

A simple and efficient liquid-phase microextraction (LPME) technique was developed using directly suspended organic microdrop coupled with gas chromatography–mass spectrometry (GC–MS), for the extraction and the determination of phthalate esters (dimethyl phthalate, diethyl phthalate, diallyl phthalate, di-n-butyl phthalate (DnBP), benzyl butyl phthalate (BBP), dicyclohexyl phthalate and di-2-ethylhexyl phthalate (DEHP)) in water samples. Microextraction efficiency factors, such as nature and volume of the organic solvent, temperature, salt effect, stirring rate and the extraction time were investigated and optimized. Under the optimized extraction conditions (extraction solvent: 1-dodecanol; extraction temperature: 60 °C; microdrop volume: 7 μL; stirring rate: 750 rpm, without salt addition and extraction time: 25 min), figures of merit of the proposed method were evaluated. The values of the detection limit were in the range of 0.02–0.05 μg L⁻¹, while the R.S.D.% value for the analysis of 5.0 μg L⁻¹ of the analytes was below 7.7% (n = 4). A good linearity (r² ≥ 0.9940) and a broad linear range (0.05–100 μg L⁻¹) were obtained. The method exhibited enrichment factor values ranging from 307 to 412. Finally, the designed method was successfully applied for the preconcentration and determination of the studied phthalate esters in different real water samples and satisfactory results were attained.     

Development of liquid phase microextraction method based on solidification of floated organic drop for extraction and preconcentration of organochlorine pesticides in water samples

A simple and efficient liquid-phase microextraction (LPME) in conjunction with gas chromatography-electron capture detector (GC-ECD) has been developed for extraction and determination of 11 organochlorine pesticides (OCPs) from water samples. In this technique a microdrop of 1-dodecanol containing pentachloronitrobenzene (internal standard) is delivered to the surface of an aqueous sample while being agitated by a stirring bar in the bulk of solution. Following completion of extraction, the sample vial was cooled by putting it into an ice bath for 5 min. Finally 2 μL of the drop was injected into the GC for analysis. Factors relevant to the extraction efficiency were studied and optimized. Under the optimized extraction conditions (extraction solvent: 1-dodecanol; extraction temperature: 65 °C; sodium chloride concentration: 0.25 M; microdrop and sample volumes: 8 μL and 20 mL respectively; the stirring rate: 750 rpm and the extraction time: 30 min), figures of merit of the proposed method were evaluated. The detection limits of the method were in the range of 7-19 ng L⁻¹ and the RSD% for analysis of 2 μg L⁻¹ of OCPs was below 7.2% (n = 5). A good linearity (r² ≥ 0.993) and a relatively broad dynamic linear range (25-2000 ng L⁻¹) were obtained. After 30 min of extraction, preconcentration factors were in the range of 708-1337 for different organochlorine pesticides and the relative errors ranged from −10.1 to 10.9%. Finally the proposed method was successfully utilized for preconcentration and determination of OCPs in different real samples.     

Dispersion‐solidification liquid–liquid microextraction for volatile aromatic hydrocarbons determination: Comparison with liquid phase microextraction based on the solidification of a floating drop

Two microextraction techniques – liquid phase microextraction based on solidification of a floating organic drop (LPME‐SFO) and dispersive liquid–liquid microextraction combined with a solidification of a floating organic drop (DLLME‐SFO) – are explored for benzene, toluene, ethylbenzene and o‐xylene sampling and preconcentration. The investigation covers the effects of extraction solvent type, extraction and disperser solvents' volume, and the extraction time. For both techniques 1‐undecanol containing n‐heptane as internal standard was used as an extracting solvent. For DLLME‐SFO acetone was used as a disperser solvent. The calibration curves for both techniques and for all the analytes were linear up to 10 μg/mL, correlation coefficients were in the range 0.997–0.998, enrichment factors were from 87 for benzene to 290 for o‐xylene, detection limits were from 0.31 and 0.35 μg/L for benzene to 0.15 and 0.10 μg/L for o‐xylene for LPME‐SFO and DLLME‐SFO, respectively. Repeatabilities of the results were acceptable with RSDs up to 12%. Being comparable with LPME‐SFO in the analytical characteristics, DLLME‐SFO is superior to LPME‐SFO in the extraction time. A possibility to apply the proposed techniques for volatile aromatic hydrocarbons determination in tap water and snow was demonstrated.     

Hollow-fibre liquid-phase microextraction: a simple and fast cleanup step used for PAHs determination in pine needles

A new, fast and simple cleanup procedure, based on hollow-fibre liquid-phase microextraction (HF-LPME) is described here, used for the determination of 13 polycyclic aromatic hydrocarbons (PAHs) in complex pine needle samples. Initially, pine needle samples were sonicated in a 20 mL aqueous solution having a 20% (v:v) acetone content and 5 mL of the sonicated liquid extract was then used for the HF-LPME cleanup step. Different experimental parameters (namely: type of organic solvent used as acceptor phase, effect and type of co-solvent, salt addition, sample agitation and sampling time) were controlled and optimized based on the response of GC-MS instrument under the SIM mode. Under the optimized experimental conditions found the typical chromatograms obtained revealed that despite the very complex matrix of pine needles the HF-LPME cleanup step greatly reduced if not eliminated the presence of interferents, resulting in chromatograms which contained very cleanly separated and readily evaluable PAH peaks. In addition, the proposed method was found to be linear in the concentration 10-2000 ng g⁻¹ for most target analytes and the limits of detection for a S/N = 3 ranged between 0.01 and 0.95 ng g⁻¹ (dry weight). Furthermore, the repeatability and reproducibility were also found good. Finally, the proposed method was applied for the analysis of real pine needle samples taken for different parts of the island of Crete.     

Continuous-flow microextraction and gas chromatographic-mass spectrometric determination of polycyclic aromatic hydrocarbon compounds in water

A new method of the determination polycyclic aromatic hydrocarbons (PAHs) in water samples was developed by continuous-flow microextraction (CFME) coupled with gas chromatography-mass spectrometry (GC-MS). In this experiment, 15 mL sample solution with no salt-added was flowed at the rate of 1.0 mL min⁻¹ through 3 μL benzene as extraction solvent. Under the optimal extraction conditions, the developed method was found to yield a linear calibration curve in the concentration range from 0.05 to 15 ng mL⁻¹. Furthermore, the accuracy and repeatability of the method were good by calculating from water samples spiked at known concentrations of PAHs, and the recovery of optimal method was satisfactory. The results showed that CFME was an efficient preconcentration method for extraction of PAHs from spiked water samples.     

Liquid-phase microextraction and GC for the determination of primary, secondary and tertiary aromatic amines as their iodo-derivatives

Presence of iodine in aromatic amines, introduced by their reaction with iodine, and other electron withdrawing substituents such as chlorine and nitro, has been found to afford excellent liquid-phase microextraction (LPME) in toluene and separation by gas chromatography in the determination of primary, secondary and tertiary aromatic amines. The effect is due to decreased basic nature of amines when electronegative substituents are present. Single drop microextraction (SDME) of the amines in 2 μl of toluene and injection of the whole extract into GC, or LPME into 50 μl of toluene and injection of 2 μl of extract, were used. LPME has been found more robust and to give better extraction in shorter period than SDME. In SDME-GC-FID, the average correlation coefficient was 0.9939 and average limit of detection 25 μg l⁻¹ (range 12-61 μg l⁻¹) whereas the corresponding values in LPME-GC-MS were, respectively, 0.9953 and 33 ng l⁻¹ (range 18-60 ng l⁻¹). The method has been applied to determine aromatic amines in river water, dye factory effluents and food dye stuffs. The LPME was found as robust, rugged and simple extraction method.     

Dispersive liquid–liquid microextraction method based on solidification of floating organic drop for extraction of organochlorine pesticides in water samples

A new simple and rapid dispersive liquid–liquid microextraction method has been developed for the extraction and analysis of organochlorine pesticides (OCPs) in water samples. The method is based on the solidification of a floating organic drop (DLLME-SFO) and is combined with gas chromatography/electron capture detection (GC/ECD). Very little solvent is required in this method. The disperser solvent (200 μL acetonitrile) containing 10 μL hexadecane (HEX) is rapidly injected by a syringe into the 5.0 mL water sample. After centrifugation, the fine HEX droplets (6 ± 0.5 μL) float at the top of the screw-cap test tube. The test tube is then cooled in an ice bath. After 5 min, the HEX solvent solidifies and is then transferred into a conical vial, where it melts quickly at room temperature, and 1 μL of it is injected into a gas chromatograph for analysis. Under optimum conditions, the enrichment factors and extraction recoveries are high and range between 37–872 and 82.9–102.5%, respectively. The linear range is wide (0.025–20 μg L⁻¹), and the limits of detection are between 0.011 and 0.11 μg L⁻¹ for most of the analytes. The relative standard deviation (RSD) for 1 μg L⁻¹ of OCPs in water was in the range of 5.8–8.8%. The performance of the method was gauged by analyzing samples of lake and tap water.     

Dynamic three-phase hollow fiber microextraction based on two immiscible organic solvents with automated movement of the acceptor phase

Dynamic three-phase hollow fiber liquid-liquid-liquid microextraction (HF-LLLME) based on two immiscible organic solvents, with automated movement of organic acceptor phase to facilitate mass transfer was introduced for the first time. Polycyclic aromatic hydrocarbons were used as model compounds and extracted from water and soil samples. The extraction involved filling an 8 cm length of hollow fiber with 25 μL of organic acceptor solvent using a microsyringe, followed by impregnation of the pores in the fiber wall with n-dodecane. The fiber was then immersed in 20 mL of aqueous sample solution. During extraction, the organic acceptor phase was repeatedly moved in the lumen of the hollow fiber by movement of the syringe plunger controlled by programmable syringe pump. Following this microextraction, 2 μL of organic acceptor phase was injected into gas chromatography-flame ionization detector. This new technique provided up to 554-fold preconcentration of the analytes under the optimized conditions. Good repeatabilities (with RSDs ≤8.4%) were obtained. Detection limits were in the range of 0.2-0.5 μg/L. The utilization of the proposed method for extraction of the polycyclic aromatic hydrocarbons from different real samples (such as water and soil samples) also gave good precision and recovery.     

Determination of organic micropollutants in rainwater using hollow fiber membrane/liquid-phase microextraction combined with gas chromatography-mass spectrometry

A simple and rapid liquid-phase microextraction (LPME) method using a hollow fiber membrane (HFM) in conjunction with gas chromatography-mass spectrometry (GC-MS) is presented for the quantitative determination of 16 polycyclic aromatic hydrocarbons (PAHs) and 12 organochlorine pesticides (OCPs) in rainwater samples. The LPME conditions were optimized for achieving high enrichment of the analytes from aqueous samples, in terms of hollow fiber exposure time, stirring rate, sample pH, and composition. Enrichment factors of more than 100 could be achieved within 35 min of extraction with relative standard deviations (R.S.D.s) 1.3-13.6% for PAHs and 1.7-13.8% for OCPs, respectively, over a wide range of analyte concentrations. Detection limits ranged from 0.002 to 0.047 microg l(-1) for PAHs, and from 0.013 to 0.059 microg l(-1) for OCPs, respectively. The newly developed LPME-GC-MS method has been validated for the analysis of PAHs and OCPs in rainwater samples. Extraction recoveries from spiked synthetic rainwater samples varied from 73 to 115% for PAHs and from 75 to 113% for OCPs, respectively. Real rainwater samples were analyzed using the optimized method. The concentrations of PAHs and OCPs in real rainwater samples were between 0.005-0.162, and 0.063 microg l(-1), respectively.     

Application of liquid-phase microextraction to the analysis of trihalomethanes in water

A liquid-phase microextraction method for the determination of trihalomethanes (THMs) including chloroform (CHCl₃), bromodichloromethane (CHBrCl₂), dibromochloromethane (CHBr₂Cl) and bromoform (CHBr₃) in water samples was developed, with analysis by gas chromatography-electron capture detection (GC-ECD). After the determination of the most suitable solvent and stirring rate for the extraction, several other parameters (solvent drop volume, extraction time and ionic strength of the sample) were optimized using a factorial design to obtain the most relevant variables. The optimized extraction conditions for 5 mL of sample volume in a 10 mL vial were as follows: n-hexane an organic solvent; a solvent drop volume of 2 μL; an extraction time of 5.0 min; a stirring rate of 600 rpm at 25 °C; sample ionic strength of 3 M sodium chloride. The linear range was 1-75 μg L⁻¹ for the studied THMs. The limits of detection (LODs) ranged from 0.23 μg L⁻¹ (for CHBr₂Cl) to 0.45 μg L⁻¹ (for CHCl₃). Recoveries of THMs from fortified distilled water were over 70% for a fortification level of 15 μg L⁻¹, and relative standard deviations of the recoveries were below 5%. Real samples collected from tap water and well water were successfully analyzed using the proposed method. The recovery of spiked water samples was from 73% to 78% with relative standard deviations below 7%.     

A novel silver-coated solid-phase microextraction metal fiber based on electroless plating technique

A novel silver-coated solid-phase microextraction fiber was prepared based on electroless plating technique. Good extraction performance of the fiber for model compounds including phthalate esters (dibutyl phthalate, dioctyl phthalate, dicyclohexyl phthalate and diallyl phthalate) and polycyclic aromatic hydrocarbons (naphthalene, fluorene, phenanthrene, fluoranthene) in aqueous solution was obtained. Under the optimized conditions (extraction temperature, extraction time, ionic strength and desorption temperature), the proposed SPME-GC method showed wide linear ranges with correlation coefficients (R²) ranging from 0.9745 to 0.9984. The limits of detection were at the range of 0.02 to 0.1 μg L⁻¹. Single fiber repeatability and fiber-to-fiber reproducibility as well as stability to acid, alkali and high temperature were studied and the results were all satisfactory. The method was applied successfully to the aqueous extracts of disposable paper cup and instant noodle barrel. Several kinds of analytes were detected and quantified.     

Microporous silica with nanolayer structure coated with renewable organic solvent film as a novel extracting phase: A combination of solid- and liquid-phase microextraction

A new method based on combination of solid- and liquid-phase microextraction was developed. For the first time, porous flower-like silica microstructures with nanometric layers were created on the surface of the stainless steel wire by a new facile hydrothermal process. The fiber, coated with a suitable organic solvent, was applied for microextraction of some organophosphorus pesticides from aqueous samples followed by gas chromatography-nitrogen phosphorous detection. Method detection limits were between 0.6 and 3 ng L⁻¹. Relative standard deviations for intra- and inter-day precision were 4.4–7.3% and 5.1–7.8%, respectively. Fiber-to-fiber reproducibility for five prepared fibers was 6.3–8.4%. Tap, river and waste water samples were analyzed for evaluation of the method in real sample analysis. Relative recoveries for spiked tap, river and waste water samples were in the range of 94–101%, 89–97% and 82–103%, respectively. In addition, the method was compared with two commercial solid-phase microextraction (SPME) fibers, single drop microextraction (SDME) and liquid-phase microextraction (LPME). The present method showed higher extraction efficiency as compared with SDME, LPME and commercial SPME fibers.     

Headspace solvent microextraction and gas chromatographic determination of some polycyclic aromatic hydrocarbons in water samples

Headspace solvent microextraction (HSME) was shown to be an efficient preconcentration method for extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A microdrop of 1-butanol (as extracting solvent) containing biphenyl (as internal standard) was used in this investigation. Extraction occurred by suspending a 3 μl drop of 1-butanol from the tip of a microsyringe fixed above the surface of solution in a sealed vial. After extraction for a preset time, the microdrop was retracted back into the syringe and injected directly into a GC injection port. The effects of nature of extracting solvent, microdrop and sample temperatures, stirring rate, microdrop and sample volumes, ionic strength and extraction time on HSME efficiency were investigated and optimized. Finally, the enrichment factor, dynamic linear range (DLR), limit of detection (LOD) and precision of the method were evaluated by water samples spiked with PAHs. The optimized procedure was successfully applied to the extraction and determination of PAHs in different water samples.     

Determination of haloethers in water with dynamic hollow fiber liquid-phase microextraction using GC-FID and GC-ECD

Dynamic hollow fiber liquid-phase microextraction (HF-LPME) coupled with gas chromatography with flame ionization detection (GC-FID) and GC-electron capture detecion (GC-ECD) was used for quantification of toxic haloethers in lake water. The analytes were extracted from 5 ml of aqueous sample using 4 μl of organic solvent through a porous polypropylene hollow fiber. The effects on extraction performance of solvent selection, agitation rate, extraction time, extraction temperature, concentration of salt added and volumes of solvent for extraction and injection were optimized. The proposed method provided a good average enrichment factor of up to 231-fold, reasonable reproducibility ranging from 9 to 12% (n = 3), and good linearity (R² ≧ 0.9973) for spiked water samples. Method detection limits (MDLs) ranged from 0.55 to 4.30 μg/l for FID and 0.11-0.34 μg/l for ECD (n = 7).     

Application of dispersive liquid–liquid microextraction based on solidification of floating organic drop for simultaneous determination of alachlor and atrazine in aqueous samples

Dispersive liquid–liquid microextraction based on solidification of floating organic drop coupled with HPLC‐UV detection as a fast and inexpensive technique was applied to the simultaneous extraction and determination of traces of two common herbicides, alachlor and atrazine, in aqueous samples. The critical experimental parameters, including type of the extraction and disperser solvents as well as their volumes, sample pH, salt addition, and extraction time were investigated and optimized. Under the optimum conditions, the calibration graphs found to be linear in the range of 0.1–200 μg/L with LOD in the range of 0.02–0.05 μg/L. The RSDs were in the range of 4.2–5.3% (n = 5). The relative recoveries of well, tap, and river water samples which have been spiked with different levels of herbicides were 94.0–106.0, 99.0–105.0, and 88.5–97.0%, respectively.     

Liquid-phase deposition of silica nanoparticles into a capillary for in-tube solid-phase microextraction coupled with high-performance liquid chromatography

A silica nanoparticle (NP)-deposited capillary fabricated by liquid-phase deposition (LPD) and modified with octadecyl groups was introduced for in-tube solid-phase microextraction coupled to high-performance liquid chromatography with UV detection (in-tube SPME–HPLC). The resultant capillary (60 cm × 50 μm I.D.) was demonstrated to be of higher extraction capacity by comparing with an octadecyl-grafted bare capillary and an octadecyl-grafted silica-coated capillary that was prepared by sol–gel chemistry. Two groups of compounds, endocrine disruptors and polycyclic aromatic hydrocarbons, were used as model analytes to further evaluate extraction capacity of the silica NP-deposited capillary, and its reproducibility and stability was also investigated. The extraction time profiles were monitored for all the chemicals, and their limits of detection were calculated to be in the range of 0.42–0.78 and 0.034–0.19 ng/mL with RSD values of peak area less than 4.6%.     

Determination of polycyclic aromatic hydrocarbons in water by a novel mesoporous‐coated stainless steel wire microextraction combined with HPLC

A novel mesoporous‐coated stainless steel wire microextraction coupled with the HPLC procedure for quantification of four polycyclic aromatic hydrocarbons in water has been developed, based on the sorption of target analytes on a selectively adsorptive fiber and subsequent desorption of analytes directly into HPLC. Phenyl‐functionalized mesoporous materials (Ph‐SBA‐15) were synthesized and coated on the surfaces of a stainless steel wire. Due to the high porosity and large surface area of the Ph‐SBA‐15, high extraction efficiency is expected. The influence of various parameters on polycyclic aromatic hydrocarbons extraction efficiency were thoroughly studied and optimized (such as the extraction temperature, the extraction time, the desorption time, the stirring rate and the ionic strength of samples). The results showed that each compound for the analysis of real water samples was tested under optimal conditions with the linearity ranging from 1.02×10^?3 to 200 μg/ L and the detection limits were found from 0.32 to 2.44 ng/ L, respectively. The RSD of the new method was smaller than 4.10%.     

Ultrasound-assisted emulsification microextraction method based on applying low density organic solvents followed by gas chromatography analysis for the determination of polycyclic aromatic hydrocarbons in water samples

In this study, a fast, simple and efficient ultrasound-assisted emulsification microextraction (USAEME) method was successfully developed based on applying low density organic solvents. Fourteen microliters of toluene was injected slowly into a 12 mL home-designed centrifuge glass vial containing an aqueous sample that was located inside the ultrasonic water bath. The formed emulsion was centrifuged and 2 μL of separated toluene (about 4 μL) was injected into a gas chromatographic system equipped with a flame ionization detector (GC-FID) for analysis. Some polycyclic aromatic hydrocarbons (PAHs) were selected as model compounds for developing the method and evaluating its performance and to compare the efficiency of the proposed method with previously reported techniques. Several factors influencing the emulsification, extraction and collection efficiency such as the nature and volume of organic solvent, emulsification–extraction temperature, ionic strength and equilibrium and centrifugation times were investigated and optimized. Under the optimum conditions, preconcentration factors (PFs) in a range of 1776–2714 were obtained. The performance of the proposed method was studied in terms of linear dynamic range (LDRs from 0.05 to 100 μg L⁻¹), linearity (R² ≥ 0.994), precision (repeatability: RSD% ≤ 7.9, reproducibility: RSD% ≤ 14.6) and extraction percents (59.2–90.5%). Limits of detection (LODs) in the range of 0.02–0.05 μg L⁻¹ were obtained for different PAHs. The applicability of the proposed method was evaluated by the extraction and determination of PAHs from several natural water samples.