碰撞池-电感耦合等离子体质谱法测定芝麻中痕量的锗

建立了碰撞池-电感耦合等离子体质谱法测定芝麻中痕量的锗元素(germanium , Ge)。采用微波消解,碰撞池(KED模式)-电感耦合等离子体质谱检测,在线引入内标元素铑(Rh),同时消解液中加入3%正戊醇增敏。结果 3 % 正戊醇可使_⁷⁴Ge的上机检测信号强度提高2.85倍,_⁷⁴Ge校正曲线线性相关系数为1.00000,检出限为0.0555 μg/kg,加标回收率为92.0%~106%,相对标准偏差(relative standard deviation, RSD%)为2.6%~4.3%。采用建立的方法测定7种国家标准物质,检测结果均在认定值范围内,RSD%为2.5%~8.8%。结论 该方法灵敏度高、准确,可实现批量检测,适用于芝麻中痕量锗的检测。     

Removal of spectral interferences and accuracy monitoring of trace cadmium in feeds by dynamic reaction cell inductively coupled plasma mass spectrometry

In the direct ICP-MS determination of Cd in feed samples, significant spectral interferences caused by high concentrations of Mo can play an important role. In the present study, Mo based oxide or hydroxide polyatomic interferences were eliminated by dynamic reaction cell (DRC) with O₂ as reaction gas. Some other oxide or hydroxide interferences (i.e. Zr and Ru) were simultaneously reduced by this technology. These potentially interfering polyatomic ions ⁹⁵Mo¹⁶O⁺, ⁹⁴Mo¹⁶OH⁺, ⁹⁴Zr¹⁶OH⁺, ⁹⁸Mo¹⁶O⁺, ⁹⁸Ru¹⁶O⁺ and ⁹⁷Mo¹⁶OH⁺ on ¹¹¹Cd⁺ and ¹¹⁴Cd⁺ were oxidized to higher oxides MoO₂⁺, MoO₃⁺, MoO₄⁺, RuO₃⁺, RuO₄⁺, MoO₂H⁺, MoO₃H⁺, ZrO₂H⁺ and ZrO₃H⁺. The rejection parameter q (RPq) of DRC and the flow rate of O₂ were optimized and set at 0.75 and 2.0 ml min^{− 1}, respectively. In addition, the residual isobaric interference of ¹¹⁴Sn on ¹¹⁴Cd was corrected using a mathematical correction equation. The limit of quantitation (LOQ) for ¹¹¹Cd or ¹¹⁴Cd was 0.8 or 1.0 ng g^{− 1} and the analysis results of NIST 1567a wheat flour and 1568a rice flour standard reference materials were in good agreement with the certified values. As the routine cadmium monitoring method in our laboratory, the proposed method was applied to the accuracy determination of 562 pig feed samples for the Monitoring of Central Meat Reserves (CMR) of China.     

Microwave assisted extraction of iodine and bromine from edible seaweed for inductively coupled plasma-mass spectrometry determination

The feasibility of microwave energy to assist the solubilisation of edible seaweed samples by tetramethylammonium hydroxide (TMAH) has been investigated to extract iodine and bromine. Inductively coupled plasma-mass spectrometry (ICP-MS) has been used as a multi-element detector. Variables affecting the microwave assisted extraction/solubilisation (temperature, TMAH volume, ramp time and hold time) were firstly screened by applying a fractional factorial design (2^5-1 + 2), resolution V and 2 centre points. When extracting both halogens, results showed statistical significance (confidence interval of 95%) for TMAH volume and temperature, and also for the two order interaction between both variables. Therefore, these two variables were finally optimized by a 2² + star orthogonal central composite design with 5 centre points and 2 replicates, and optimum values of 200 °C and 10 mL for temperature and TMAH volume, respectively, were found. The extraction time (ramp and hold times) was found statistically non-significant, and values of 10 and 5 min were chosen for the ramp time and the hold time, respectively. This means a fast microwave heating cycle. Repeatability of the over-all procedure has been found to be 6% for both elements, while iodine and bromine concentrations of 24.6 and 19.9 ng g⁻¹, respectively, were established for the limit of detection. Accuracy of the method was assessed by analyzing the NIES-09 (Sargasso, Sargassum fulvellum) certified reference material (CRM) and the iodine and bromine concentrations found have been in good agreement with the indicative values for this CRM. Finally, the method was applied to several edible dried and canned seaweed samples.     

Element fingerprinting of marine organisms by dynamic reaction cell inductively coupled plasma mass spectrometry

A method for the determination of sixteen elements (Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Se, Sn, V, Zn) in seafood by dynamic reaction cell inductively coupled plasma mass spectrometry (ICP–DRC–MS) is presented. A preliminary study of polyatomic interferences was carried out in relation to the chemical composition of marine organisms belonging to different taxa. Acid effects and other matrix effects in marine organisms submitted to closed-vessel microwave digestion were investigated as well. Ammonia was the reactive gas used in the DRC to remove polyatomic ions interfering with ²⁷Al, ⁵²Cr, ⁵⁶Fe and ⁵¹V. Optimal conditions for the simultaneous determination of analytes were identified in order to develop a fast multielement method. A suite of real samples (mussels and various fish species) were used during method development along with three certified reference materials: BCR CRM 278R (mussel tissue), BCR CRM 422 (cod muscle) and DORM-2 (dogfish muscle). The proposed analytical approach can be used in conjunction with suitable chemometric procedures to address quality and safety issues in aquaculture and fisheries. As an example, a case study is described in which mussels from three farming sites in the Venice Lagoon were distinguished by multivariate analysis of element fingerprints.      

Simultaneous quantification of 17 trace elements in blood by dynamic reaction cell inductively coupled plasma mass spectrometry (DRC-ICP-MS) equipped with a high-efficiency sample introduction system

A quadrupole inductively coupled plasma mass spectrometer (Q-ICP-MS) equipped with a dynamic reaction cell (DRC) and coupled with a desolvating nebulization system (APEX-IR) was employed to determine 17 elements (Al, As, Ba, Cd, Co, Cr, Li, Mn, Mo, Ni, Pb, Sb, Se, Sn, Sr, V, and Zr) in blood samples. Ammonia (for Al, Cr, Mn, and V) and O₂ (for As and Se) were used as reacting gases. Selection of the best flow rate of the gases and optimization of the quadrupole dynamic bandpass tuning parameter (RPq) were carried out, using digested blood diluted 1 + 9 with deionized water and spiked with 1 μg L⁻¹ of Al, Cr, Mn, V and 5 μg L⁻¹ of As and Se. Detection limits were determined in digested blood using the 3σ criterion. The desolvating system allowed a sufficient sensitivity to be achieved to determine elements at levels of ng L⁻¹ without detriment of signal stability. The accuracy of the method was tested with the whole blood certified reference material (CRM), certified for Al, As, Cd, Co, Cr, Mn, Mo, Ni, Pb, Sb, Se, and V, and with indicative values for Ba, Li, Sn, Sr, and Zr. The addition calibration approach was chosen for analysis. In order to confirm the DRC data, samples were also analyzed by means of sector field inductively coupled plasma mass spectrometry (SF-ICP-MS), operating in medium (m/Δm = 4000) and high (m/Δm = 10,000) resolution mode and achieving a good agreement between the two techniques.     

Determination of sulfur-containing amino acids by capillary electrophoresis dynamic reaction cell inductively coupled plasma mass spectrometry

Capillary electrophoresis dynamic reaction cell™ inductively coupled plasma mass spectrometry (CE-DRC-ICP-MS) for the determination of sulfur-containing amino acids is described. The sulfur-containing amino acids studied include l-cysteine, l-cystine, dl-homocystine and l-methionine. The species studied were well separated using a 70 cm length×75 μm i.d. fused silica capillary while the applied voltage was set at +22 kV and a 10 mmol l⁻¹ disodium tetraborate buffer (pH 9.8) containing 0.1 mmol l⁻¹ EDTA and 0.5 mmol l⁻¹ Triton X-100 was used as the electrophoretic buffer. The sulfur-selective electropherogram was determined at m/z 48 as by using its reaction with O₂ in the reaction cell. The method avoided the effect of polyatomic isobaric interferences at m/z 32 caused by and on by detecting as the oxide ion at m/z 48, which is less interfered. The detection limit of various species studied was in the range of 0.047-0.058 μg S ml⁻¹, which corresponded to the absolute detection limit of 1.3-1.6 pg S based on the injection volume of 27 nl. We determined the concentrations of selected sulfur-containing amino acids in urine and nutritive complement samples. The recovery was in the range of 92-128% for various species.     

A high-throughput solid-phase extraction microchip combined with inductively coupled plasma-mass spectrometry for rapid determination of trace heavy metals in natural water

Herein, a hyphenated system combining a high-throughput solid-phase extraction (htSPE) microchip with inductively coupled plasma-mass spectrometry (ICP-MS) for rapid determination of trace heavy metals was developed. Rather than performing multiple analyses in parallel for the enhancement of analytical throughput, we improved the processing speed for individual samples by increasing the operation flow rate during SPE procedures. To this end, an innovative device combining a micromixer and a multi-channeled extraction unit was designed. Furthermore, a programmable valve manifold was used to interface the developed microchip and ICP-MS instrumentation in order to fully automate the system, leading to a dramatic reduction in operation time and human error. Under the optimized operation conditions for the established system, detection limits of 1.64–42.54 ng L⁻¹ for the analyte ions were achieved. Validation procedures demonstrated that the developed method could be satisfactorily applied to the determination of trace heavy metals in natural water. Each analysis could be readily accomplished within just 186 s using the established system. This represents, to the best of our knowledge, an unprecedented speed for the analysis of trace heavy metal ions.     

Determination of the ratio of calcium to phosphorus in foodstuffs by dynamic reaction cell inductively coupled plasma mass spectrometry

An inductively coupled plasma mass spectrometer (ICP–MS) equipped with a dynamic reaction cell (DRC) was used for the determination of Ca and P in foodstuffs. In this study, two different reaction gases, CH₄ and O₂, were introduced successively through the different channels to alleviate different interferences in the same analysis run. The effect of the operating conditions of the DRC system was studied to get the best signal-to-noise ratio for each element. The interfering ⁴⁰Ar⁺ at m/z 40 was reduced in intensity by up to five orders of magnitude by using 1.0 mL min^–1 CH₄ as reaction cell gas in the DRC. On the other hand, by using O₂ as the reaction gas, ³¹P⁺ was converted to ³¹P¹⁶O⁺ that could be detected at m/z 47 where there was less interference. The limits of detection for Ca and P were 0.2 ng mL^–1 and 0.3 ng mL^–1, respectively. This method was used to determine the concentrations of Ca and P and the ratio of Ca to P in NIST SRM 1549 non-fat milk powder and NIST RM 8345 whole milk powder reference materials and an infant milk powder and an infant cereal-rice sample purchased locally. The results for the reference samples agreed satisfactorily with the reference values. The accuracy of the determination was better than 4.1 and 0.9% for Ca and P, respectively. The results for infant milk powder and infant cereal were also found to be in good agreement with the value on the bottle label. Precision (RSD) between sample replicates was better than 4.8% for all the determinations.     

Dry ashing of organic rich matrices with palladium for the determination of arsenic using inductively coupled plasma-mass spectrometry

A dry ashing procedure is developed for the determination of As in organic rich matrices such as wheat flour, lichen and tobacco leaves. The volatility of As during dry ashing is avoided by the addition of palladium nitrate [Pd(NO₃)₂]. The recovery of both As(III) and As(V) is found to be near quantitative. The residue after dry ashing is dissolved in nitric acid (HNO₃) and analysed by inductively coupled plasma-mass spectrometry (ICP-MS). The process blank and limit of detection (LOD) are 11 and 6.6 ng g⁻¹, respectively. The procedure is applied for the determination of As in certified reference materials namely wheat flour NIST SRM 1567a (National Institute of Standards and Technology Standard Reference Material), lichen BCR CRM 482 (Institute for Reference Materials, European Commission) and Virginia tobacco leaves CTA-VTL-2 (Poland Academy of Sciences). The results obtained by the present procedure are in good agreement with the certified values and also determined after complete dissolution of samples using closed microwave digestion.     

电感耦合等离子体质谱(ICP-MS)法测定地质样品中Cu和Zn的干扰研究

电感耦合等离子体质谱(ICP-MS)法标准模式测定地质样品中Cu和Zn时,样品溶液中Ti在高温下易形成TiO⁺和TiOH⁺产生离子重叠干扰,使测定值偏离真值而影响测定结果。采用氢氟酸-高氯酸-硝酸消解、王水复溶样品,通过多级在线校正⁴⁶Ti¹⁶O⁺,消除TiO⁺和TiOH⁺离子重叠干扰,研究了单质Ti与⁴⁶Ti¹⁶O⁺、质荷比63、64、65、66离子间存在的关系,建立了一种电感耦合等离子体质谱(ICP-MS)法测定地质样品中Cu和Zn的分析方法。结果表明：单质Ti对Cu和Zn产生的干扰值与其质量浓度呈非简单的正相关性,TiO⁺产生的干扰离子质荷比65离子强度比63高,质荷比64离子强度比66高;⁴⁶Ti¹⁶O⁺对质荷比63、66离子干扰增量值与单质Ti质量浓度变化无关;^6...     

Determination of arsenic, iron and selenium in moss samples using hexapole collision cell, inductively coupled plasma-mass spectrometry

Different collision gases (H₂, He and premixed 7% H₂ in He) used in the hexapole collision cell of an inductively coupled plasma-mass spectrometer (ICP-MS) were compared, and the gas-flow rates were optimized for the determination of arsenic (), iron () and selenium (). The study showed that the argon-based interferences at mass-to-charge ratios (m/z) of 56, 75 and 80 can be overcome by the optimized gas flows (7.5 ml min⁻¹ premixed 7% H₂ in He and 2 ml min⁻¹ H₂) in the hexapole collision cell. Detection limits of 15.5 ng l⁻¹ for iron () and 29 ng l⁻¹ for selenium () in 2% (v/v) HNO₃ were obtained under optimized collision cell conditions. The detection limit for arsenic () obtained in difficult hydrochloride acid matrix (5% HCl (v/v)) was 153 ng l⁻¹. The accuracy of the optimized method was confirmed by analyzing two moss reference materials. The results obtained by ICP-MS for arsenic, selenium and iron from both moss reference samples were, in most cases, in good agreement with the certified values.     

Trace elements content in size-classified volcanic ashes as determined by inductively coupled plasma-mass spectrometry

At present there is an increasing concern as regards the release of potentially toxic metals into the environment. Volcanic eruptions are a natural source of metals and metalloids in the atmosphere. Toxic trace elements ejected during an eruptive episode may produce hazardous effects for people and the environment in areas close to the volcano. In this context, a study was undertaken to investigate the concentration of metal and metalloids in ashes ejected from Copahue volcano, Neuquén, Argentina. Two samples (A and B) of deposited particles were collected one day after the first eruption and size-fractionated in four sub-samples (S1, S2, S3 and S4). Analysis was performed by inductively coupled plasma-mass spectrometry (ICP-MS) and the accuracy for the entire analytical procedure was performed by means of the certified reference material CRM GBW 07105 Rocks (NRCCRM, China). The elements considered were: As, Cd, Cr, Cu, Hg, Ni, Pb, Sb, U, V and Zn. The adverse effect of potentially interfering species on the mass-spectrometric determination of these elements was also taken into account. The concentration intervals found in the four fractions are as follows (in μg g⁻¹): As, 6.0-2.6; Cd, 0.71-0.36; Cr, 29.5-54.0; Cu, 132-49.0; Hg, 0.020-0.007; Ni, 36.0-26.0; Pb, 15.5-2.55; Sb, 1.07-0.30; U, 2.57-1.94; V, 152-106; Zn, 85.5-55.0. The elements with the highest concentrations were: Cu, V and Zn. All fractions, in both samples, were found to be enriched in some toxic trace elements in the following order Sb>Cd>As. On the contrary, samples were depleted in Ni, Cr and Hg. Lead was the element that exhibits a noticeable difference in concentration between the finer and coarser fractions.     

Open-channel chip-based solid-phase extraction combined with inductively coupled plasma-mass spectrometry for online determination of trace elements in volume-limited saline samples

In this study, we used an automated online chip-based solid-phase extraction (SPE)-inductively coupled plasma-mass spectrometry (ICP-MS) system for analyzing trace elements in small-volume saline samples (～15 μL). The proposed method involved the adsorption of trace metal ions in the interior of a functionalized poly(methyl methacrylate) (PMMA) channel in order to separate these ions from saline matrices. The adsorption of transition metal ions was presumably dominated by the surface complexation between the carboxylate moieties in the interior of the PMMA channel and the metal ions, which facilitated the formation of metal-carboxylate complexes. The components of the proposed online analytical system used for the simultaneous detection of multiple trace metals in saline samples involved microdialysis (MD) sampling, an established chip-based SPE procedure, and ICP-MS. The SPE-ICP-MS hyphenated system was optimized, and then, the analytical reliability of this system was further confirmed by using it to analyze the certified reference materials-SRM 2670 (human urine) and SRM 1643e (artificial saline water). The satisfactory analytical results indicated that the proposed on-chip SPE device could be readily used as an interface for coupling the MD probe with the ICP-MS system. The dramatically reduced consumption of chemicals and "hands-on" manipulations enabled the realization of a simplified and relatively clean procedure with extremely low detection limits in the range of 5.86-76.91 ng L(-1) for detecting Mn, Co, Ni, Cu, and Pb in 15-μL samples by ICP-MS. The effectiveness of an online MD-chip-based SPE-ICP-MS technique for continuous monitoring of trace elements in a simulated biological system was also demonstrated. To the best of our knowledge, this is the first paper to report the direct exploitation of a PMMA chip as an SPE adsorbent for online sample pretreatment and trace metal preconcentration prior to ICP-MS measurement.     

New application of microwave digestion-inductively coupled plasma-mass spectrometry for multi-element analysis in komatiites

A new method using microwave digestion combined with inductively coupled plasma-mass spectrometry (ICP-MS) was studied to analyze the elemental composition of a variety of komatiites samples. Microwave digestion consisted in two-stage heating and pressurizing acid treatments for maximum dissolution of the samples. We report here different quality control measurements (external and internal calibration, monitoring of reference materials) which involve standard deviation calculations and recovery examinations in order to test the precision and accuracy of the analytical procedure. Data for 17 elements (Na, P, K, T, V Cr, Mn, Co, Ni, Cu, Zn, Zr, Pb, Al, F, Ca and Mg) in eight komatiite samples and two USGS basalt reference samples (BCR-2 and BHVO-2) are presented. We evaluate our new digestion and instrumental procedure. The element concentration obtained for BCR-2 and BHVO-2 agreed well with the certified values, the relative standard deviations were lower than 5% and recoveries were good. Our analytical results demonstrate that it reproduces accurately the concentrations of minor and trace elements in komatiites. The ease of digestion of the samples and the speed (less than 12 h) to digest the komatiite material makes this technique an efficient method to be used easily and routinely for preparing and analyzing komatiites samples for multiple elements determination.     

Development of a new method for sulfide determination by vapor generator–inductively coupled plasma–mass spectrometry

A new sensitive methodology for the determination of total reduced sulfur species in natural waters and acid volatile sulfides in sediments at low levels (μg L^− 1) is described. Reduced sulfur species were separated from the water matrix in the form of H₂S after reaction with hydrochloric acid in a commercial vapor generator coupled to an inductively coupled plasma quadrupole mass spectrometer (VG–ICP–QMS) equipped with a reaction cell. The method avoided the effect of polyatomic isobaric interferences at m/z 32 caused by ¹⁶O¹⁶O⁺ and ¹⁴N¹⁸O⁺ through the elimination of the aqueous matrix, a source of oxygen. By introducing a mixture of helium and hydrogen gases into the octopole reaction cell, a series of ion-molecule reactions were induced to reduce the interfering polyatomic species. Operating conditions of the octopole reaction cell system and the analyzer were optimized to get the best signal to background ratio for ³²S; a full factorial 2³ experimental design was developed in order to evaluate which variables had a significant effect and a simplex methodology was applied to find the optimum conditions for the variables. The new method was evaluated by comparison to the standard potentiometric method. The analytical methodology developed was applied to the analysis of reduced sulfur species in natural waters and acid volatile sulfides in sea sediments.     

液相色谱-电感耦合等离子体质谱法测定稻米中的5种砷形态

建立了稻米中砷酸根[As（Ⅴ）]、亚砷酸根[As（Ⅲ）]、砷甜菜碱（AsB）、一甲基砷（MMA）和二甲基砷（DMA）的液相色谱-电感耦合等离子体质谱（LC-ICP-MS）检测方法。以0.3 mol/L硝酸水溶液为提取试剂,样品在石墨消解仪中于95 ℃消解1.5 h,上清液供LC-ICP-MS分析。5种砷形态采用Dionex IonPac AS19阴离子交换柱（250 mm×4 mm）分离,经ICP-MS检测。比较了4种提取液对稻米中5种砷形态的提取效率,并对提取溶剂的浓度、提取温度和提取时间等条件进行了优化。通过加标回收试验结合测定标准物质考察了方法准确度及精密度,在2个加标水平上各形态的回收率为89.6%~99.5%,RSD（n=5）不大于3.6%,大米标准物质中各形态之和的测定结果与其标准值吻合,5种砷形态的线性范围AsB和DMA为0.05~200 μg/L,As（Ⅲ）和MMA为0.10~400 μg/L,As（V）为0.15~600 μg/L,方法检出限为0.15~0.45 μg/kg。结果表明,本方法简单、灵敏、耐用,可用于稻米中5种砷形态的准确定量和风险评估。     

Development of a method based on inductively coupled plasma-dynamic reaction cell-mass spectrometry for the simultaneous determination of phosphorus,calcium and strontium in bone and dental tissue

A method, based on the use of a quadrupole-based inductively coupled plasma-mass spectrometry instrument equipped with a quadrupole-based collision/reaction cell (dynamic reaction cell, DRC), was developed for the simultaneous determination of phosphorus, calcium and strontium in bone and dental (enamel and dentine) tissue. The use of NH₃, introduced at a gas flow rate of 0.8 mL min^− 1 in the dynamic reaction cell, combined with a rejection parameter q (RPq) setting of 0.65, allows interference-free determination of calcium via its low-abundant isotopes ⁴²Ca, ⁴³Ca and ⁴⁴Ca, and of strontium via its isotopes ⁸⁶Sr and ⁸⁸Sr that are freed from overlap due to the occurrence of ArCa⁺ and/or Ca₂⁺ ions. Also the determination of phosphorus (³¹P, mono-isotopic) was shown to be achievable using the same dynamic reaction cell operating conditions. The bone certified reference materials NIST SRM 1400 Bone Ash and NIST SRM 1486 Bone Meal were used for validation of the measurement protocol that was shown capable of providing accurate and reproducible results. Detection limits of P, Ca and Sr in dental tissue digests were established as 3 µg L^− 1 for P, 2 µg L^− 1 for Ca and 0.2 µg L^− 1 for Sr. This method can be used to simultaneously (i) evaluate the impact of diagenesis on the elemental and isotopic composition of buried skeletal tissue via its Ca/P ratio and (ii) determine its Sr concentration. The measurement protocol was demonstrated as fit-for-purpose by the analysis of a set of teeth of archaeological interest for their Ca/P ratio and Sr concentration.     

Electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry for the determination of Fe,Co, Ni,Cu, and Zn in biological samples

Slurry sampling electrothermal vaporization dynamic reaction cell inductively coupled plasma mass spectrometry (ETV-DRC-ICP-MS) has been applied to determine Fe, Co, Ni, Cu, and Zn in biological samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Pd was used as the modifier. The effectiveness of the ETV sample introduction technique and dynamic reaction cell in alleviating various spectral interferences in ICP-MS analysis has been demonstrated. This method has been applied to determine Fe, Co, Ni, Cu, and Zn in NIST SRM 1573a tomato leaves reference material and NRCC DORM-2 dogfish muscle reference material and also real samples such as a tea and a swordfish sample purchased locally. Since the sensitivities of the elements studied in slurry and aqueous solution were different, an analyte addition technique was used for the determinations. The analytical results of the reference materials agreed with the certified values. The precision between sample replicates was better than 6% for all determinations. The method detection limit estimated from analyte addition curves was 0.01, 0.006, 0.007, 0.004, and 0.006 μg g⁻¹ for Fe, Co, Ni, Cu, and Zn, respectively, in the original biological samples.     

电感耦合等离子体质谱法测定岩石中47种元素的不确定度评定

采用封闭酸溶电感耦合等离子体质谱(ICP-MS)法测定岩石样品,分别对47种元素的测量结果不确定度进行评定。通过分析测试方法和测量条件,得到测量结果的不确定度主要由样品称量、样品溶液定容和样品溶液中元素浓度测量引入。在实验室质控条件下,对各不确定度分量进行评定和计算,其中随机因素导致的不确定度采用期间精密度试验综合评价,即采用A类方法评定。共完成了16个岩石国家标准物质(GBW 07103~GBW 07123)47种元素测量结果的不确定度合成,并参照GB/T 6379.2-2004,建立了含量w与扩展不确定度U之间的关系模型,运用这一关系模型可得到测量结果的不确定度估计值,只要测量过程本身或所使用的设备未变化,就不需要再重复进行不确定度评估。