有机-无机杂化高分子絮凝剂PAC-PDMDAAC的合成与表征

以过硫酸铵为引发剂,以乙二胺四乙酸四钠(Na4EDTA)为助剂合成了新型有机-无机杂化高分子絮凝剂聚合氯化铝-聚二甲基二烯丙基氯化铵(PAC-PDMDAAC).实验考查了DMDAAC单体质量分数、引发剂用量、反应温度以及反应时间对杂化絮凝剂合成的影响.结果表明杂化高分子絮凝剂的最佳合成条件为单体质量分数30%,引发剂质量分数0.7%,反应温度60℃,反应时间5 h.傅里叶红外光谱(FTIR)、热重分析(TGA)以及扫描电镜(SEM)测试结果表明,杂化聚合物PDMDAAC链端有—SO42-离子存在,其与带正电荷的羟基铝粒子以离子键形式键合.扫描电镜结果显示杂化絮凝剂具有更大的比表面积,易于发挥吸附架桥作用.采用Al-Ferron逐时络合比色法研究絮凝剂中Al形态,结果表明杂化絮凝剂中Alc部分,即不与Ferron发生络合反应的高聚物明显增多.由PAC、复配型PAC-PDMDAAC和杂化型PAC-PDMDAAC絮凝剂分别处理腐植酸-高岭土模拟水样和长江水,结果表明杂化型絮凝剂在浊度和UV254的去除率上优于其它二者.     

坡缕石/聚丙烯酰胺无机-有机杂化絮凝剂的合成、表征与应用

将酸活化坡缕石(PGS)与氯化乙醇胺(EACl)所得氯化乙醇胺改性坡缕石(PGS-EACl)与高价铈盐(Ce⁴⁺)组成氧化还原非均相引发体系,引发丙烯酰胺单体聚合得到了坡缕石/聚丙烯酰胺(PGS/PAM)无机-有机杂化物.用¹HNMR、FTIR、粘度法和电导法对杂化物进行了结构表征,表明杂化物中存在PGS^Θ⊕NH₃R离子键合作用.考察了PGS-EACl用量、聚合反应时间和单体浓度对杂化物特性粘数的影响.由PGS/PAM杂化絮凝剂分别处理高岭土和氧化铁红两种配制废水,发现杂化絮凝剂的絮凝效果明显优于纯PAM絮凝剂.     

SET-LRP法制备星型疏水缔合水溶性聚合物

采用丙烯酰胺(AM)、2-丙烯酰胺基-2-甲基丙磺酸钠(NaAMPS)以及N-叔丁基丙烯酰胺(NtBA)为共聚单体,以Cu~0粉/三(2-二甲氨基乙基)胺(Me_6-TREN)为催化体系,四氯化碳(CCl_4)为引发剂,利用单电子转移自由基聚合(SET-LRP)方法合成星型疏水缔合水溶性聚合物P(AM/NtBA/NaAMPS)。采用控制变量法分别考察了引发温度、疏水单体含量、AMPS含量、引发剂用量、催化剂铜、单体浓度等因素对聚合物相对分子质量的影响,确定了最佳聚合条件并考察了聚合物的耐温抗盐性能。结果表明,当单体浓度为35%,引发温度为25℃,AM、AMPS、NtBA分别占单体总量的93.6%、5%、1.4%(摩尔比),引发剂质量分数为0.4942%,催化剂铜的质量分数为0.0848%,钝化剂的质量分数为0.1192%时,所得星型疏水缔合水溶性聚合物P(AM/NtBA/NaAMPS)的相对分子质量出现最高值为267万,同时具有一定的耐温抗盐性,其溶液性能与线型化的P(AM/NtBA/NaAMPS)相似,且在相同浓度下CaCl_2对聚合物表观粘度的影响比NaCl大。     

阳离子聚丙烯酰胺的制备及其絮凝性能

研究了氧化还原引发剂质量分数、偶氮类引发剂质量分数、阳离子度等因素对所制备的阳离子聚丙烯酰胺特性粘数的影响,探讨了pH值、阳离子聚丙烯酰胺特性粘数、阳离子度、用量等因素对污泥絮凝性能的影响. 较佳的制备条件为:复合引发体系中(NH4 )2 S2 O8 和CH3 NaO3 S·2H2 O总质量分数为0.015 0%、偶氮类引发剂质量分数为0.012 5%、单体质量分数为40%、阳离子度为40%,产物特性粘数为13.1 dL/g. 在污泥pH=6.0、阳离子聚丙烯酰胺特性粘数为11.9 dL/g、阳离子度为40%、用量为0.027%的较佳絮凝条件下,污水的透光率达98.0%,絮凝率达66.0%,脱水率达70.0%.     

淀粉基阳离子絮凝剂的研制及性能测试

用可溶性淀粉为原料,通过接枝改性合成了一种淀粉基阳离子絮凝剂(MSF),其最佳制备工艺条件为:淀粉与丙烯酰胺的质量比为1:2,引发剂用量为0.6 g,反应温度为50 ℃,接枝时间为3.5 h;阳离子化条件为:甲醛和二甲胺摩尔比为1.0:1.4,反应时间2.5 h,反应温度50 ℃.产物结构经FTIR证实.用其处理番茄废水后,废水的透光率提高了78.2%、TOC下降了22.5%、COD下降了37.25%,结果表明该产品对高浓度有机废水的絮凝性能优于聚丙烯酰胺高分子絮凝剂(PAM).     

阳离子聚丙烯酰胺合成工艺条件及絮凝性能的研究

以丙烯酰胺(AM)和甲基丙烯酰氧乙基三甲基氯化铵(DMC)为共聚单体,采用氧化还原/偶氮化合物复合引发剂体系在水溶液中进行自由基聚合,合成了阳离子型聚丙烯酰胺聚合物(CPAM)。系统研究了反应条件对反应产物的影响,用红外光谱对CPAM的结构进行了表征。结果表明,制备较高分子量CPAM的优化工艺参数为:单体总质量分数35%(AM∶DMC=3∶1),氧化还原引发剂质量分数0.06%((NH_4)_2S_2O_8∶NaHSO_3=1∶1),偶氮类引发剂质量分数0.09%,助溶剂质量分数1.5%,络合剂质量分数1.5%。在此优化条件下,所得CPAM的分子量达1.2×10~6,对蒙脱土模拟废水的絮凝效果良好,经其处理后的模拟废水透光率达到99.3%。     

PAMPS/SiO_2杂化水凝胶的合成及电场敏感性研究

以2-丙烯酰胺-2-甲基丙磺酸(AMPS)为有机原料,正硅酸乙酯(TEOS)为无机原料,过硫酸钾为引发剂,N,N'-亚甲基双丙烯酰胺为交联剂,通过原位-凝胶水溶液聚合法合成了一系列不同二氧化硅含量和不同聚离子浓度的聚(2-丙烯酰胺-2-甲基丙磺酸)/二氧化硅杂化电场敏感性水凝胶.通过扫描电子显微镜(SEM)表征凝胶的结构,研究水凝胶在去离子水以及氯化钠溶液中的溶胀和消溶胀行为.结果表明,系列凝胶的平衡溶胀度介于224.9至325.6之间,复合凝胶的溶胀速率随TEOS用量的增加而降低;除理想杂化凝胶外,随着聚离子浓度的升高,凝胶在氯化钠溶液中的消溶胀速率逐渐减小.对凝胶的电场敏感性研究表明,当聚离子浓度大于氯化钠溶液浓度时,凝胶进一步溶胀,反之则消溶胀,其中杂化凝胶的再溶胀性能减弱,而消溶胀行为变得更为明显.同时制得的理想杂化凝胶,较纯有机凝胶具有更为理想的力学性能,最大抗压缩强度可达23.4 MPa.     

新型的含葡萄糖胺的水溶性高分子型硫杂蒽酮光引发剂

将硫杂蒽酮光引发剂(TX)和共引发剂葡萄糖胺(GA)引入同一个高分子链上,合成新型水溶性高分子型硫杂蒽酮光引发剂(PTX-GA).通过改变PTX-GA中TX与GA的比例,合成了PTX-GA1、PTX-GA2、PTX-GA3,并通过光膨胀计实验研究了3种引发剂引发丙烯酰胺聚合的能力.研究表明这种水溶性高分子型硫杂蒽酮光引发剂即使在没有共引发剂胺的情况下,引发丙烯酰胺(AAM)的聚合效率也非常显著.同时由于它具有水溶性,而且含有生物分子,有利于改善光引发剂的生物相容性.     

咪唑型阳离子聚丙烯酰胺P(AM/MAPD)的合成

以丙烯酰胺(AM)、自制的1-(2-甲基丙烯酰氧丙基)-3-癸基咪唑盐酸盐(MAPD-Cl)为原料,通过自由基共聚合,得到了咪唑型阳离子聚丙烯酰胺P(AM/MAPD)。 红外光谱表征结果证明其为目标产物。 采用单因素考察和响应面分析法相结合,对聚合工艺条件进行了优化。 优化聚合条件为：单体总质量分数25.41%,反应温度26 ℃,引发剂(NaHSO3-(NH4)2S2O4)质量分数0.03%,反应时间10 h。 所得聚合物的特性粘数可达到12.56 dL/g。     

三次采油耐温抗盐聚合物的合成与评价

以丙烯酰胺(AM)、2-丙烯酰胺基-2-甲基丙磺酸(AMPS)和氢氧化钠(Na OH)为原料,采用过硫酸铵[(NH4)2S2O8]、亚硫酸钠(Na2SO3)和四甲基脲[N(CH3)2CON(CH3)2]作为新型复合引发体系,通过共聚后水解工艺,合成了高分子量三元共聚物(AM-AANa-AMPSNa).考察了引发剂用量、单体浓度、p H和引发温度对共聚物黏均分子量的影响.确定最优条件为:引发剂用量0.035%,单体质量浓度为25%,介质p H 7,引发温度0℃.通过红外光谱和核磁碳谱表征了其结构,并系统评价了其理化性能指标、黏弹性、注入性和驱油性能.结果表明,该共聚物较高分子量部分水解聚丙烯酰胺(HPAM)具有更优异的耐温抗盐性能.其黏均相对分子量达到3000万以上,在胜利油田III型盐水中,浓度1500 mg/L,温度85℃条件下,溶液表观黏度达到17.7 m Pa s,岩心驱油实验在水驱采收率51.8%基础上,可再提高15.8%.上述性能表明,该高分子量三元共聚物有望应用在高温高盐油藏三次采油技术中.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.