Nitrogen Limitation in Neochloris oleoabundans: A Reassessment of Its Effect on Cell Growth and Biochemical Composition

The aim of this work was to reassess the effect of nitrogen limitation (from 0 to 1 mM nitrate), on the growth and the biochemical composition of Neochloris oleoabundans cultures, where only the CO₂ available in the air was provided. Slight differences in the initial nitrate concentration, even minimal increments of 0.2 mM, significantly modify the microalgal response towards nitrogen limitation. This stress condition reduced cell proliferation, but increased cell mass values due to the simultaneous accumulation of two storage compounds: lipids, which contained up to a 55.9 % of total fatty acids; and carbohydrates, which may be primarily composed by starch. The highest biomass and lipid productivities of 98.24 and 43.24 mg/l/day, respectively, were attained at an initial nitrate concentration of 0.6 mM. The theoretical annual projection, based on these productivities, allowed the estimation of the liquid fuel energy yields, which are comparable or even higher than those calculated for several biomass feedstocks such as corn, oil palm, sugarcane, or even fast growing grasses, confirming the potential of nitrogen-limited N. oleoabundans biomass as an appropriate feedstock for biofuel purposes.     

Efficient Conversion of Fructose-Based Biomass into Lipids with <Emphasis Type="Italic">Trichosporon fermentans</Emphasis> Under Phosphate-Limited Conditions

Limiting nitrogen supply has been routinely used as the master regulator to direct lipid biosynthesis. However, this strategy does not work with nitrogen-rich substrates, such as Jerusalem artichoke (JA), a fructose-based biomass, while it is difficult to obtain a high carbon-to-nitrogen (C/N) molar ratio. In this study, an alternative strategy to promote lipid accumulation by the oleaginous yeast Trichosporon fermentans CICC 1368 was developed by limiting phosphorous supply, and this strategy was implemented with JA hydrolysate as substrate. We showed that lipid accumulation was directly correlated with the C/P ratio of the culture media for T. fermentans. The time course of cell growth and lipid production was analyzed in a media with an initial C/P ratio of 6342, and the cellular lipid content could reach up to 48.5% of dry biomass. Moreover, JA hydrolysates were used as substrate for microbial lipid accumulation, under high C/P molar ratio condition, lipid yield, lipid content, and lipid coefficient increased by 10, 30, and 34%, respectively. It showed that by limiting phosphorus, the conversion of sugar into lipids can be improved effectively. Limiting phosphorus provides a promising solution to the problem of microbial lipid production with nitrogen-rich natural materials.     

Fermentation Characteristics of <Emphasis Type="Italic">Mortierella alpina</Emphasis> in Response to Different Nitrogen Sources

The fermentation characteristics of Mortierella alpina were investigated in response to various nitrogen sources. Influences on nitrogen source and glucose uptake rate, mycelial morphology of M. alpina, and pH of medium in relation to different nitrogen sources were discussed. Effects of different nitrogen sources on cell growth, fatty acid composition, arachidonic acid (ARA), and total lipid concentration were also evaluated. It revealed that the maximum nitrogen source uptake ratio was obtained when corn steep liquor was used as nitrogen source. When yeast extract was used as the sole nitrogen source, glucose was completely exhausted at the end of fermentation. The maximum dry cell weight obtained from medium with yeast extract as nitrogen source had the highest total lipid concentration. Sodium nitrate was the favorable nitrogen source for ARA accumulation, and the highest ARA percentage in total fatty acids was obtained, 35.9%. Urea was identified as the favorable nitrogen source for ARA production, the highest ARA concentration obtained from urea was 5.8 g/l. Compared with inorganic nitrogen sources, organic nitrogen compounds are favorable for both cell growth and total lipids accumulation.     

An integrated microfluidic device for the high-throughput screening of microalgal cell culture conditions that induce high growth rate and lipid content

This study describes the development of a microfluidic device for the high-throughput screening of culture conditions, such as the optimum sodium acetate concentration for promoting rapid growth and high lipid accumulation of Chlamydomonas reinhardtii. An analysis of the microalgal growth on the microfluidic device revealed an optimum sodium acetate concentration of 5.72 g L^?1. The lipid content, determined by the 4,4-Difluoro-1,3,5,7-tetramethyl-4-bora-3a,4a-diaza-s-indacene (BODIPY® 505/515) staining method, increased with the sodium acetate concentration. The results were found to be statistically reproducible with respect to cell growth and lipid production. Other nutrient conditions, including the nitrogen and phosphorus concentrations, can also be optimized on the same microfluidic platform. The microfluidic device performance results agreed well with the results obtained from the flask-scale experiments, validating that the culture conditions were scalable. Finally, we, for the first time, established a method for the absolute quantification of the microalgal lipid content in the picoliter culture volumes by comparing the on-chip and off-chip data. In conclusion, we successfully demonstrated the high-throughput screening of sodium acetate concentrations that induced high growth rates and high lipid contents in C. reinhardtii cells on the microfluidic device.

Influence of Exogenous CO2 on Biomass and Lipid Accumulation of Microalgae Auxenochlorella protothecoides Cultivated in Concentrated Municipal Wastewater

The effects of exogenous CO₂ on the growth and lipid accumulation of a local screened facultative heterotrophic microalgae strain Auxenochlorella protothecoides (UMN280) as well as nutrient removal from concentrated municipal wastewater stream (centrate) were examined in this study. A 12-day batch experiment was conducted with CO₂ aeration at three levels, namely, 0%, 1%, and 5% (v/v) CO₂ mixed with air, under light intensity of 60???mol/(m² @@s). A two-stage growth pattern was observed. The first stage (first?Cfifth day) was dominated by heterotrophic growth in which organic carbon was the main carbon source. The second stage (6th?C12th day) was dominated by autotrophic growth in which exogenous CO₂ had a positive effect on algal biomass accumulation. The addition of 5% CO₂ was better than that of 1% CO₂ on the biomass and lipid production. The uptakes of nutrients were similar between injection and no injection of CO₂, except on phosphorus removal which was affected by the acidification of CO₂.     

Use of NAD(P)H Fluorescence Measurement for On-Line Monitoring of Metabolic State of Azohydromonas australica in Poly(3-hydroxybutyrate) Production

Culture fluorescence measurement is an indirect and non-invasive method of biomass estimation to assess the metabolic state of the microorganism in a fermentation process. In the present investigation, NAD(P)H fluorescence has been used for on-line in situ characterization of metabolic changes occurring during different phases of batch cultivation of Azohydromonas australica in growth associated poly(3-hydroxybutyrate) or PHB production. A linear correlation between biomass concentration and net NAD(P)H fluorescence was obtained during early log phase (3–12 h) and late log phase (24–39 h) of PHB fermentation. After 12 h (mid log phase) cultivation PHB accumulation shot up and a drop in culture fluorescence was observed which synchronously exhibited continuous utilization of NAD(P)H for the synthesis of biomass and PHB formation simultaneously. A decrease in the observed net fluorescence value was observed again towards the end of fermentation (at 39 h) which corresponded very well with the culture starvation and substrate depletion towards the end of cultivation inside the bioreactor. It was therefore concluded that NAD(P)H fluorescence measurements could be used for indication of the time of fresh nutrient (substrate) feed during substrate limitation to further enhance the PHB production.     

A New Isolate from Fusarium proliferatum (AUF-2) for Efficient Nitrilase Production

A fungal isolate from Fusarium proliferatum strain AUF-2 has been found to have a high nitrilase activity (≥1,000 U/l culture). The present work describes optimization of growth conditions and production medium to achieve maximum nitrilase production. The most effective carbon and nitrogen sources for nitrilase production were glucose and sodium nitrate, respectively. ε-Caprolactam was found to be the best inducer for maximum nitrilase production with 80 g/l wet cell biomass and 26 U/g nitrilase activity. An overall nitrilase activity of ≥2,000 U/l culture was obtained in this study, which is one of the best activities reported so far in any Fusarium strain. Chemo-profiling has shown that the strain is versatile in its ability to hydrolyze both aliphatic as well as aromatic nitriles. Efforts are being made to use the strain for biotransformation of pharmaceutical substrates.     

Elicitation of Submerged Adventitious Root Cultures of Stevia rebaudiana with Cuscuta reflexa for Production of Biomass and Secondary Metabolites

Stevia rebaudiana is an important medicinal plant that belongs to the Asteraceae family. The leaves of Stevia rebaudiana are a rich source of many health-promoting agents such as polyphenols, flavonoids, and steviol glycoside, which play a key role in controlling obesity and diabetes. New strategies such as the elicitation of culture media are needed to enhance the productivity of active components. Herein, the Cuscuta reflexa extracts were exploited as elicitors to enhance the productivity of active components. Cuscuta reflexa is one of the parasitic plants that has the ability to elongate very fast and cover the host plant. Consequently, it may be possible that the addition of Cuscuta reflexa extracts to adventitious root cultures (ADR) of Stevia rebaudiana may elongate the root more than control cultures to produce higher quantities of the desired secondary metabolites. Therefore, the main objective of the current study was to investigate the effect of Cuscuta reflexa extract as a biotic elicitor on the biomass accumulation and production of antioxidant secondary metabolite in submerged adventitious root cultures of Stevia rebaudiana. Ten different concentrations of Cuscuta reflexa were added to liquid media containing 0.5 mg/L naphthalene acetic acid (NAA). The growth kinetics of adventitious roots was investigated for a period of 49 days with an interval of 7 days. The maximum biomass accumulation (7.83 g/3 flasks) was observed on medium containing 10 mg/L extract of Cuscuta reflexa on day 49. As the concentration of extract increases in the culture media, the biomass gradually decreases after 49 days of inoculation. In this study, the higher total phenolics content (0.31 mg GAE/g-DW), total flavonoids content (0.22 mg QE/g-DW), and antioxidant activity (85.54%) were observed in 100 mg/L treated cultures. The higher concentration (100 mg/L) of Cuscuta reflexa extract considerably increased the total phenolics content (TPC), total phenolics production (TPP), total flavonoids content (TFC), total flavonoids production (TFP), total polyphenolics content (TPPC), and total polyphenolics production (TPPP). It was concluded that the extract of Cuscuta reflexa moderately improved biomass accumulation but enhanced the synthesis of phenolics, flavonoids, and antioxidant activities. Here, biomass’s independent production of secondary metabolites was observed with the addition of extract. The present study will be helpful to scale up adventitious roots culture into a bioreactor for the production of secondary metabolites rather than biomass accumulation in medicinally important Stevia rebaudiana.     

Microbial Lipid Production from Corn Stover via Mortierella isabellina

Microbial lipid is a promising source of oil to produce biofuel if it can be generated from lignocellulosic materials. Mortierella isabellina is a filamentous fungal species featuring high content of oil in its cell biomass. In this work, M. isabellina was studied for lipid production from corn stover. The experimental results showed that M. isabellina could grow on different kinds of carbon sources including xylose and acetate, and the lipid content reached to 35 % at C/N ratio of 20. With dilution, M. isabellina could endure inhibition effects by dilute acid pretreatment of corn stover (0.3 g/L furfural, 1.2 g/L HMF, and 1 g/L 4-hydroxybenozic acid) and the strain formed pellets in the cell cultivations. An integrated process was developed combining the dilute acid pretreatment, cellulase hydrolysis, and cell cultivation for M. isabellina to convert corn stover to oil containing fungal biomass. With 7.5 % pretreated biomass solid loading ratio, the final lipid yield from sugar in pretreated biomass was 40 % and the final lipid concentration of the culture reached to 6.46 g/L.     

Photoautotrophic and Mixotrophic Cultivation of Polyhydroxyalkanoate-Accumulating Microalgae Consortia Selected under Nitrogen and Phosphate Limitation

Microalgae consortia were photoautotrophically cultivated in sequencing batch photobioreactors (SBPRs) with an alteration of the normal growth and starvation (nutrient limitation) phases to select consortia capable of polyhydroxyalkanoate (PHA) accumulation. At the steady state of SBPR operation, the obtained microalgae consortia, selected under nitrogen and phosphate limitation, accumulated up to 11.38% and 10.24% of PHA in their biomass, which was identified as poly(3-hydroxybutyrate) (P3HB). Photoautotrophic and mixotrophic batch cultivation of the selected microalgae consortia was conducted to investigate the potential of biomass and PHA production. Sugar source supplementation enhanced the biomass and PHA production, with the highest PHA contents of 10.94 and 6.2%, and cumulative PHA productions of 100 and 130 mg/L, with this being achieved with sugarcane juice under nitrogen and phosphate limitation, respectively. The analysis of other macromolecules during batch cultivation indicated a high content of carbohydrates and lipids under nitrogen limitation, while higher protein contents were detected under phosphate limitation. These results recommended the selected microalgae consortia as potential tools for PHA and bioresource production. The mixed-culture non-sterile cultivation system developed in this study provides valuable information for large-scale microalgal PHA production process development following the biorefinery concept.     

Low-Cost Production of Green Microalga Botryococcus braunii Biomass with High Lipid Content Through Mixotrophic and Photoautotrophic Cultivation

Botryococcus braunii is a microalga that is regarded as a potential source of renewable fuel because of its ability to produce large amounts of lipid that can be converted into biodiesel. Agro-industrial by-products and wastes are of great interest as cultivation medium for microorganisms because of their low cost, renewable nature, and abundance. In this study, two strategies for low-cost production of B. braunii biomass with high lipid content were performed: (i) the mixotrophic cultivation using molasses, a cheap by-product from the sugar cane plant as a carbon source, and (ii) the photoautotrophic cultivation using nitrate-rich wastewater supplemented with CO₂ as a carbon source. The mixotrophic cultivation added with 15 g L^?1 molasses produced a high amount of biomass of 3.05 g L^?1 with a high lipid content of 36.9 %. The photoautotrophic cultivation in nitrate-rich wastewater supplemented with 2.0 % CO₂ produced a biomass of 2.26 g L^?1 and a lipid content of 30.3 %. The benefits of this photoautotrophic cultivation are that this cultivation would help to reduce accumulation of atmospheric carbon dioxide and more than 90 % of the nitrate could be removed from the wastewater. When this cultivation was scaled up in a stirred tank photobioreactor and run with semi-continuous cultivation regime, the highest microalgal biomass of 5.16 g L^?1 with a comparable lipid content of 32.2 % was achieved. These two strategies could be promising ways for producing cheap lipid-rich microalgal biomass that can be used as biofuel feedstocks and animal feeds.     

Response Surface Optimization of Medium Components for Naringinase Production from <Emphasis Type="Italic">Staphylococcus xylosus MAK2</Emphasis>

Response surface methodology was used to optimize the fermentation medium for enhancing naringinase production by Staphylococcus xylosus. The first step of this process involved the individual adjustment and optimization of various medium components at shake flask level. Sources of carbon (sucrose) and nitrogen (sodium nitrate), as well as an inducer (naringin) and pH levels were all found to be the important factors significantly affecting naringinase production. In the second step, a 22 full factorial central composite design was applied to determine the optimal levels of each of the significant variables. A second-order polynomial was derived by multiple regression analysis on the experimental data. Using this methodology, the optimum values for the critical components were obtained as follows: sucrose, 10.0%; sodium nitrate, 10.0%; pH 5.6; biomass concentration, 1.58%; and naringin, 0.50% (w/v), respectively. Under optimal conditions, the experimental naringinase production was 8.45 U/mL. The determination coefficients (R ²) were 0.9908 and 0.9950 for naringinase activity and biomass production, respectively, indicating an adequate degree of reliability in the model.     

N<Subscript>2</Subscript>O Production by Nitrifying Biomass Under Anoxic and Aerobic Conditions

The capacity of nitrifying biomass, grown in biofilms or in suspension, to reduce NO₂ ^- and NO₃ ⁻ under anoxic conditions was tested in batch experiments. The estimated reduction rates were 5 and 25 mg N per gram volatile suspended solids (VSS) per day for nitrate and nitrite, respectively, in the case of the nitrifying biofilms. Activity tests carried out with successive feedings indicated that no acclimation of the biomass to the tested conditions occurred, as the obtained reduction rates remained almost constant. Another series of activity assays was carried out with nitrifying suspended biomass, and the reduction rates for nitrate and nitrite were 30.4 and 48.9 mg N per gram VSS per day, respectively. N₂O and N₂ were the final gaseous products, and their percentages depended on the source of nitrogen feed. The specific production of nitrous oxide during nitrification was investigated during continuous experiments in a biofilm airlift suspension reactor. Specific production rates up to 46 mg N₂O–N per gram VSS per day were measured. The percentage of N₂O produced represented up to 34.4% of the ammonia oxidized. Nitrite accumulation, low dissolved oxygen concentrations, and the presence of organic matter favored the production of nitrous oxide. N₂O gas was not detected during the oxidation of nitrite even when organic matter was present. To prevent N₂O gas production in nitrifying systems, the operation at low dissolved oxygen concentrations, nitrite presence, or organic matter content should be avoided.     

Harnessing the Effect of pH on Lipid Production in Batch Cultures of <Emphasis Type="Italic">Yarrowia lipolytica</Emphasis> SKY7

The objective of this research was to investigate the kinetics of lipid production by Yarrowia lipolytica SKY7 in the crude glycerol-supplemented media with and without the control of pH. Lipid and citric acid production were improved with the pH control condition. There was no significant difference observed in the biomass concentration with or without the pH control. In the pH-controlled experiments, the biomass and lipid concentration reached 18 and 7.78 g/L, (45.5% w/w), respectively, with lipid yield (Yp/s) of 0.179 g/g at 60 h of fermentation. The lipid production was directly correlated with growth and the process was defined as growth associated. After 60 h of fermentation, the lipid degradation was noticed in the pH-controlled reactor whereas it occurred after 84 h in the pH-uncontrolled reactor. Apart from lipid, citric acid was produced as the major extracellular product in both fermentations but the much lower concentration in uncontrolled pH. Based on the experimental results, it is evident that controlling the pH will enhance the lipid production by 15% compared to pH-uncontrolled fermentation.     

Elucidating the Effect of Glycerol Concentration and C/N Ratio on Lipid Production Using <Emphasis Type="Italic">Yarrowia lipolytica</Emphasis> SKY7

The high demand for renewable energy and increased biodiesel production lead to the surplus availability of crude glycerol. Due to the above reason, the bio-based value addition of crude glycerol into various bioproducts is investigated; among them, microbial lipids are attractive. The present study was dedicated to find the optimal glycerol concentration and carbon/nitrogen (C/N) ratio to produce maximum lipid using Yarrowia lipolytica SKY7. The glycerol concentration (34.4 to168.2 g/L) and C/N ratio (25 to 150) were selected to investigate to maximize the lipid production. Initial glycerol concentration 112.5 g/L, C/N molar ratio of 100, and with 5 % v/v inoculum supplementation were found to be optimum for biomass and lipid production. Based on the above optimal parameters, lipid concentration of 43.8 % w/w with a biomass concentration of 14.8 g/L was achieved. In the case of glycerol concentration, the maximum Yp/s (0.192 g/g); Yx/s (0.43 g/g) was noted when the initial glycerol concentration was 112.5 g/L with C/N molar ratio 100 and inoculum volume 5 % v/v. The glycerol uptake was also noted to increase with the increase in glycerol concentration. At low C/N ratio, the glycerol consumption was found to be high (79.43 g/L on C/N 25) whereas the glycerol consumption was observed to decrease when the C/N ratio was raised to 150 (40.8 g/L).     

Effect of Furfural on <Emphasis Type="Italic">Saccharomyces carlsbergensis</Emphasis> Growth,Physiology and Ethanol Production

This work described the effect of furfural, a product resulting from the lignocellulosic material pretreatment, on Saccharomyces carlsbergensis growth and ethanol production. Flow cytometry was used to evaluate the yeast membrane potential, membrane integrity, reactive oxygen species production and lipid content. Above 0.3 g/L of furfural, a progressive decrease in the maximal specific growth rate was observed, reaching 53% of the value obtained in the absence of toxic when the cells were grown in the presence of 4 g/L of furfural. In general, the yeast biomass concentration and yield were less affected by the furfural presence than the specific growth rate, and a maximum reduction of 25% was observed for the assay at 4 g/L. The ethanol production was even less affected by the furfural presence than the yeast growth. At 4 g/L of furfural, the maximum ethanol concentration was reduced by only 10% relatively to the maximum ethanol concentration observed in the absence of toxic. At 5 g/L of furfural, the yeast cells were barely able to keep metabolic functions and produced a final ethanol concentration of 0.87 g/L although growth was undetectable. S. carlsbergensis membrane potential was affected by the furfural presence, concomitantly with the ethanol production. However, at 4 g/L, most of the yeast cells (90%) displayed the cytoplasmic membrane depolarized. The proportion of cells with increasing reactive oxygen species (ROS) production levels increased for the experiments at 0–4 g/L. For the experiment at 4.5 g/L of furfural, ROS production was observed for only 11% of the yeast cells. The yeast lipid content was also severely affected by the furfural presence. Both polar and neutral lipids decreased in the presence of furfural, and this reduction was more notorious during the stationary phase.     

Growth of Cyanobacteria: Optimization for Increased Carbohydrate Content

Growths of Lyngbya limnetica and Oscillatoria obscura were investigated at varying pH, light intensity, temperature, and trace element concentration with a view to optimize these parameters for obtaining the maximum carbohydrate content. The maximum growth for both strains was obtained at pH 9.0 and temperature 20 ± 3 °C using a light intensity of 68.0 μmol m^?2 s^?1 with continuous shaking. Growth under the nitrogen starvation condition affected the carbohydrate content more compared to the phosphorus starvation, and maximum concentrations were found as 0.660 and 0.621 g/g of dry biomass for L. limnetica and O. obscura, respectively. Under the optimized nitrogen-rich conditions, the specific growth rates for the two strains were found to be 0.187 and 0.215 day^?1, respectively. The two-stage growth studies under nitrogen-rich (stage I) followed by nitrogen starvation (stage II) conditions were performed, and maximum biomass and carbohydrate productivity were found as 0.088 and 0.423 g L^?1 day^?1 for L. limnetica. This is the first ever attempt to evaluate and optimize various parameters affecting the growth of cyanobacterial biomass of L. limnetica and O. obscura as well as their carbohydrate contents.     

Statistical Analysis and Modeling of Pelletized Cultivation of Mucor circinelloides for Microbial Lipid Accumulation

Microbial oil accumulation via oleaginous fungi has some potential benefits because filamentous fungi can form pellets during cell growth and these pellets are easier to harvest from the culture broth than individual cells. This research studied the effect of various culture conditions on the pelletized cell growth of Mucor circinelloides and its lipid accumulation. The results showed that cell pelletization was positively correlated to biomass accumulation; however, pellet size was negatively correlated to the oil content of the fungal biomass, possibly due to the mass transfer barriers generated by the pellet structure. How to control the size of the pellet is the key to the success of the pelletized microbial oil accumulation process.     

Effects of pH and Carbon Source on <Emphasis Type="Italic">Synechococcus</Emphasis> PCC 7002 Cultivation: Biomass and Carbohydrate Production with Different Strategies for pH Control

Synechococcus PCC 7002 is an interesting species in view of industrial production of carbohydrates. The cultivation performances of this species are strongly affected by the pH of the medium, which also influences the carbohydrate accumulation. In this work, different methods of pH control were analyzed, in order to obtain a higher production of both Synechococcus biomass and carbohydrates. To better understand the influence of pH on growth and carbohydrate productivity, manual and automatic pH regulation in CO₂ and bicarbonate system were applied. The pH value of 8.5 resulted the best to achieve both of these goals. From an industrial point of view, an alternative way to maintain the pH practically constant during the entire period of cultivation is the exploitation of the bicarbonate-CO₂ buffer system, with the double aim to maintain the pH in the viability range and also to provide the amount of carbon required by growth. In this condition, a high concentration of biomass (6 g L^?1) and carbohydrate content (around 60 %) were obtained, which are promising in view of a potential use for bioethanol production. The chemical equilibrium of C-N-P species was also evaluated by applying the ionic balance equations, and a relation between the sodium bicarbonate added in the medium and the equilibrium value of pH was discussed.     

Xylanase production by Penicillium canescens 10–10c in solid-state fermentation

Filamentous fungi have been widely used to produce hydrolytic enzymes for industrial applications, including xylanases, whose levels in fungi are generally much higher than those in yeast and bacteria. We evaluated the influence of carbon sources, nitrogen sources, and moisture content on xylanase production by Penicillium canescens 10–10c in solid-state fermentation. Among agricultural wastes tested (wheat bran, untreated wheat straw, treated wheat straw, beet pulp, and soja meal), untreated wheat straw gave the highest production of xylanase. Optimal initial moisture content for xylanase production was 83%. The addition of 0.4 g of xylan or easily metabolizable sugar, such as glucose and xylose, at a concentration of 2% to wheat straw enhanced xylanase production. In solid-state fermentation, even at high concentrations of glucose or xylose (10%), catabolic repression was minimized compared to the effect observed in liquid culture. Yeast extract was the best nitrogen source among the nitrogen sources investigated: peptone, ammonium nitrate, sodium nitrate, ammonium chloride, and ammonium sulfate. A combination of yeast extract and peptone as nitrogen sources led to the best xylanase production.