基于金属-介质-金属结构的反射式彩色滤光片特性研究

研究了金属-介质-金属结构在可见光波段的反射滤光特性。该结构由柔性透明基底、金属层、介质-金属纳米光栅结构组成。利用严格耦合波分析法(RCWA)模拟了TM偏振光入射时,亚波长介质-金属光栅的占宽比、周期和厚度等结构参数对反射光谱特性的影响。理论模拟结果表明:光栅的结构参数变化可改变反射波段,进而调节滤光颜色。在此基础上,进一步优化结构参数,得到了基于减色法的彩色滤光片结构,获得了青色、品红色和黄色三原色。该结构的主要优点是,当入射角在0～45范围内变化时,反射光谱谷值位置和反射带宽基本不变。本文所提出的结构特别适合用于反射式彩色显示。     

真空紫外波段光栅二级衍射效率测量装置

利用光栅二级衍射会影响反射样品光谱反射率结果的原理,通过计算不同光谱反射率获得了光栅二级衍射效率。介绍了测量二级衍射效率的实验装置,该装置采用双光路单色仪结构,使用已知光谱辐亮度氘灯作为光源,探测器为光电倍增管,通过水杨酸钠膜将紫外光转为可见光。以波长161nm为例,测量了5块反射镜样片,计算得到光栅二级衍射效率为0.00611×(1±0.0777)。分析表明,该方法采用的测试装置简单,系统不确定度为14.08%,可以实现真空紫外波段光栅二级光谱衍射效率的连续测量。     

亚波长金属偏振分束光栅设计分析

结合有效介质理论和薄膜光学的抗反射设计方法,设计了基于0.65μm工作波长的亚波长金属偏振分束光栅,给出了光栅的优化设计参数,采用严格耦合波理论分析了光栅的偏振分束特性.结果表明,亚波长金属光栅对TE偏振表现为金属膜特性,具有高反射,对TM偏振表现为介质膜特性,具有高透射,在-30°<θ<30°的大入射角范围和0.47μm<λ<0.80μm的宽入射波谱内,该光栅的透射光和反射光均具有高偏振消光比和低插入损耗的特点. 关键词： 亚波长金属偏振分束光栅 有效介质理论 薄膜光学 严格耦合波理论     

一种基于MEMS光栅光调制器的近红外光谱探测系统

基于微机电系统技术的近红外光谱探测系统已成为了近红外光谱仪研究的一个新方向。文章提出了一种基于光栅光调制器的新型近红外光谱探测系统。该系统采用微加工技术制造的光栅光调制器阵列与单点近红外探测器相结合使用的方法进行光谱探测。设计了该光谱探测系统的光学结构, 论述了系统光谱探测原理, 并使用经表面微加工工艺得到的光栅光调制器器件进行了系统分辨本领、波长准确性、系统稳定性、器件响应频率等特征参数测试实验。结果表明,该探测系统在1 320到1 400 nm波长范围内,分辨本领小于10 nm, 波长准确性小于1 nm, 系统稳定性小于0.5%, 光栅光调制器的响应频率为5kHz。实验结果证明了该近红外光谱探测系统的可行性, 为研制基于微机电系统光栅光调制器的微型化近红外光谱仪提供了理论基础及实验指导。     

基于切趾取样光栅单信道直流平衡技术的光栅滤波器

提出了一种利用取样光栅周期的啁啾平衡切趾取样光栅单信道内直流分量的方法,基于该方法的切趾光栅滤波器具有波长设计灵活小受限于模板周期和只需一次曝光过程、亚微米量级制作精度的优点.利用均匀光栅最大反射率测量模型和零点带宽测量模型得到了实验所使用的载氢光纤紫外光致折射率变化量与曝光时间的关系.在此基础上,利用提出的新方法设计并实验制作了中心反射波长为1549.84 nm,3 dB带宽分别为75 pm和55 pm的两根升余弦切趾光栅滤波器,实验制作与理论设计仿真结果非常接近,成功消除了取样光栅-1级子光栅谱短波长方向处的法布里-珀罗共振现象,得到的光栅滤波器反射谱和透射谱具有良好的对称性,反射谱边带抑制度在20 dB以上.     

基于导模共振效应三基色窄带滤光片的研究

为获得性能优良的三基色窄带滤光片,提出了一种基于减反射薄膜波导光栅结构的导模共振滤光片.该滤光片由亚波长光栅结构、波导层和基底组成.采用严格耦合波理论分析了亚波长光栅结构和波导层厚度对导模共振滤光片反射光谱性能的影响.数值分析表明λ/4-λ/2-λ/4结构能有效提高导模共振滤光片的性能.当光栅结构位于基底侧时,红绿蓝三...     

基于二维矩形SiO2光子晶体光栅的研究

 为解决光学系统中普遍存在的菲涅耳反射问题,提高光的透射率,设计了一种二维矩形SiO2光子晶体结构光栅。采用勒让德多项式展开法对该结构在可见 近红外波长范围入射光波的透射率进行了模拟计算,寻找到了合适的占空比e、光栅深度h和基底厚度d,使得光栅的透射率在入射角为0～60°范围内、入射波长在400 nm～1 200 nm范围内变化时,其透射率的变化相对稳定,透射率的平均值可达到96%以上。     

亚波长金属光栅的表面等离子体激元共振特性

亚波长金属光栅在共振波长处有光场局域增强、异常透射等现象,为深入认识其共振机制,本文研究了亚波长金属光栅的表面等离子体激元（SPP）共振特性。通过研究不同金属光栅的几何结构以及金属介电常数对SPP共振波长的影响,获得了3种共振波长的基本物理机制。采用周期边界元法进行数值模拟,在边界积分方程的基础上结合平面波展开方法来处理任意形状的周期性结构。模拟结果表明,3种共振波长可以分别由金属的材料、金属光栅周期和金属光栅厚度所调谐。该研究为微纳米光学器件的设计提供了依据。     

亚波长金属光栅的表面等离子体激元共振特性

亚波长金属光栅在共振波长处有光场局域增强、异常透射等现象,为深入认识其共振机制,本文研究了亚波长金属光栅的表面等离子体激元(SPP)共振特性。通过研究不同金属光栅的几何结构以及金属介电常数对SPP共振波长的影响,获得了3种共振波长的基本物理机制。采用周期边界元法进行数值模拟,在边界积分方程的基础上结合平面波展开方法来处理任意形状的周期性结构。模拟结果表明,3种共振波长可以分别由金属的材料、金属光栅周期和金属光栅厚度所调谐。该研究为微纳米光学器件的设计提供了依据。     

宽谱段高分辨扫描光谱定标技术

为了满足原子发射光谱仪在紫外至近红外宽谱段范围内的高光谱分辨率快速检测需求,采用精密角位移平台直接驱动光栅,配合面阵探测器,实现高精度光谱分段快速扫描探测。但在扫描过程中,探测器像元波长增量与光栅转角呈非线性关系,且不同像元的波长增量不同,这对该光谱仪波长定标造成障碍。为校正光栅色散的非线性,基于光栅方程精确计算光栅转角与探测器首尾两端像元波长的映射关系,针对同一光栅转角,探测器其余像元波长利用首尾像元波长按照局部线性色散规律计算得到,从而完成全谱段光谱定标。依据定标所得转角与探测波段对应关系依次驱动光栅转动,实现宽谱段范围内的分段高精度光谱快速扫描探测。利用汞灯光源对该定标方法的波长检测精度进行检验,在200~800 nm的宽谱段范围内,波长准确度优于0.018 nm,波长重复性优于0.001 nm。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.