Effects of copolymer concentration and chain length on the pH-responsive behavior of diblock copolymer micellar films

The pH-responsive behavior of adsorbed diblock copolymer films of PDMA-PDEA (poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate)) on silica has been characterized using a quartz crystal microbalance with dissipation monitoring (QCM-D), an optical reflectometer (OR) and an atomic force microscope (AFM). The copolymer was adsorbed at pH 9 from various copolymer concentrations; QCM-D measurements indicate that the level of desorption when rinsed at pH 9 depends on the initial copolymer concentration. The adsorbed films produced at pH 9 generally have low charge densities; adjusting the solution pH to 4 results in a significant protonation of the constituent copolymers and a related interfacial structural change for the copolymer film. OR studies show no significant change during pH cycling, while QCM-D measurements indicate that the adsorbed mass and dissipation alter dramatically in response to the solution pH. The difference between the QCM-D adsorbed masses and dissipation values at pH 4 and 9 were found to be dependent on the initial copolymer concentration. This is due to differences in the initial conformations within the adsorbed copolymer layers at pH 9. The effect of the PDMA chain length on the pH-responsive behavior has also been studied; both the QCM-D adsorbed mass and dissipation of PDMA54-PDEA24 (shorter PDMA block) at pH 4 and 9 were observed to be greater than those of PDMA9X-PDEA2Y (longer PDMA block). This suggests that the normal extension of the adsorbed PDMA54-PDEA24 copolymer films is more significant than that of the PDMA9X-PDEA2Y films on silica.     

Characterizing the pH-responsive behavior of thin films of diblock copolymer micelles at the silica/aqueous solution interface

The pH-responsive behavior of cationic diblock poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) copolymer micelles adsorbed at the silica/aqueous solution interface has been characterized. The micellar morphology of this copolymer, initially adsorbed at pH 9, can be dramatically altered by lowering the solution pH. The original micelle-like morphology of the adsorbed copolymer chains at pH 9 completely disappears as the pH is decreased to 4, and a brush-like layer structure is produced. This change results from protonation of the copolymer chains: the subsequent electrostatic repulsions within the film drive the copolymer chains to expand into the aqueous phase. Returning the solution pH from 4 to 9 causes this brush-like layer to collapse, with atomic force microscopy images suggesting degradation of the film. Hence, the pH-responsive behavior of the copolymer film exhibits irreversible morphological changes. Measurements of the adsorbed/desorbed amounts of the copolymer film were conducted using both a quartz crystal microbalance with dissipation monitoring (QCM-D) and optical reflectometry (OR). After an initial rinse at both pH values, the OR adsorbed mass becomes almost constant during subsequent pH cycling, whereas the corresponding QCM-D adsorbed mass changes significantly but reversibly in response to the solution pH. Since the QCM-D measures a bound mass that moves in tandem with the surface, the discrepancy with the OR data is due to changes in the amount of bound water in the copolymer film as a result of the pH-induced changes in surface morphology. The larger effective mass observed at pH 4 suggests that the brush-like layer contains much more entrapped water than the micellar films at pH 9. The pH dependence of the contact angle of the adsorbed film is consistent with the changes observed using the other techniques, regardless of whether the solution pH is altered in situ or the aqueous solution is completely replaced. In fact, comparison of these two approaches provides direct evidence of the exposure of adsorbed micelle core blocks to the solution during pH cycling and the concomitant impact upon all the other measurements.     

Reversible pH-triggered encapsulation and release of pyrene by adsorbed block copolymer micelles

The well-established ability of copolymer micelles to encapsulate and release hydrophobic molecules has been investigated following their adsorption onto silica particles. Here, a pH-responsive copolymer, poly(2-(dimethylamino)ethyl methacrylate)- b-poly(2-(diethylamino)ethyl methacrylate) (PDMA(106)- b-PDEA(25)), has been used to study the formation and dissociation of adsorbed micelles through pH variation. This copolymer behaves as free unimers in aqueous solutions below pH 8 and forms micelles 29 nm in hydrodynamic diameter above this pH. Encapsulation and release of a model hydrophobic compound (pyrene) by in situ adjustment of the solution pH has been compared for both free and adsorbed micelles using fluorescence spectrophotometry, epifluorescence microscopy, and zeta potential measurements. At basic pH values, pyrene is solubilized within the cores of micelles adsorbed on silica particles: addition of acid leads to micelle dissociation and release of the pyrene into the bulk aqueous solution. Micelle adsorption does not appear to hinder the extent of pyrene uptake/release. Moreover, this pH-responsive behavior is both reversible and reproducible over multiple pH cycles.     

pH-responsive diblock copolymer micelles at the silica/aqueous solution interface: Adsorption kinetics and equilibrium studies

The adsorption behavior of two examples of a weakly basic diblock copolymer, poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) (PDMA-PDEA), at the silica/aqueous solution interface has been investigated using a quartz crystal microbalance with dissipation monitoring and an optical reflectometer. Dynamic and static light scattering measurements have also been carried out to assess aqueous solution properties of such pH-responsive copolymers. In alkaline solution, core-shell micelles are formed above the critical micelle concentration (cmc) by both copolymers, whereas the chains are molecularly dissolved (as unimers) at all concentrations in acidic solution. As a result, the adsorption behavior of PDMA-PDEA diblock copolymers on silica is strongly dependent on both the copolymer concentration and the solution pH. Below the cmc at pH 9, the cationic PDMA-PDEA copolymers adsorb as unimers and the conformation of the adsorbed polymer is essentially flat. At concentrations just above the cmc, the initial adsorption of copolymer onto the silica is dominated by the unimers due to their faster diffusion compared to the much larger micelles. Rearrangement of the adsorbed unimers and/or their subsequent displacement by micelles from solution is then observed during an equilibration period, and the final adsorbed mass is greater than that observed below the cmc. At concentrations well above the cmc, the much higher proportion of micelles in solution facilitates more effective competition for the surface at all stages of the adsorption process and no replacement of initially adsorbed unimers by micelles is evident. However, the adsorbed layer undergoes gradual rearrangement after initial adsorption. This relaxation is believed to result from a combination of further copolymer adsorption and swelling of the adsorbed layer.     

Film-forming microgels for pH-triggered capture and release

The pH-responsive behavior for a series of lightly cross-linked, sterically stabilized poly(tertiary amine methacrylate)-based latexes adsorbed onto mica and silica was investigated using in situ tapping mode AFM at room temperature. The adsorbed layer structure was primarily determined by the glass transition temperature, T(g), of the latex: poly[2-(diethylamino)ethyl methacrylate]-based particles coalesced to form relatively featureless uniform thin films, whereas the higher T(g) poly[2-(diisopropylamino)ethyl methacrylate] latexes retained their original particulate character. Adsorption was enhanced by using a cationic poly[2-(dimethylamino)ethyl methacrylate] steric stabilizer, rather than a nonionic poly(ethylene glycol)-based stabilizer, since the former led to stronger electrostatic binding to the oppositely charged substrate. Both types of adsorbed latexes acquired cationic microgel character and swelled appreciably at low pH, even those that had coalesced to form films. Fluorescence spectroscopy was used to study the capture of a model hydrophobic probe, pyrene, by these adsorbed latex layers followed by its subsequent release by lowering the solution pH. The repeated capture and release of pyrene through several pH cycles was also demonstrated. Since these poly(tertiary amine methacrylate) latexes are readily prepared by aqueous emulsion polymerization and adsorption occurs spontaneously from aqueous solution, this may constitute an attractive route for the surface modification of silica, mica and other oxides.     

Characterization of layer-by-layer self-assembled multilayer films of diblock copolymer micelles

The in situ layer-by-layer (LbL) self-assembly of low Tg diblock copolymer micelles onto a flat silica substrate is reported. The copolymers used here were a cationic poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) (50qPDMA-PDEA; 50q refers to a mean degree of quaternization of 50 mol % for the PDMA block) and zwitterionic poly(methacrylic acid)-block-poly(2-(diethylamino)ethyl methacrylate) (PMAA-PDEA), which has anionic character at pH 9. Alternate deposition of micelles formed by these two copolymers onto a silica substrate at pH 9 was examined. The in situ LbL buildup of the copolymer micelle films was monitored using zeta potential measurements, optical reflectometry, and a quartz crystal microbalance with dissipation monitoring (QCM-D). For a six layer deposition, complete charge reversal was observed after the addition of each layer. The OR data indicated clearly an increase in adsorbed mass with each additional micelle layer and suggest that some interdiffusion of copolymer chains between layers and/or an increase in the film roughness, and hence in the effective surface area of the micellar multilayers, must take place as the film is built up. QCM-D data indicated that the self-assembled micellar multilayers on a flat silica substrate undergo structural changes over a prolonged period. This is attributed to longer-term interdiffusion of the copolymer chains between the outer two layers after the initial adsorption of each layer is complete. The QCM-D data further suggest that the outer adsorbed layers adopt a progressively more extended conformation, particularly for the higher numbered layers. The morphology of each successive layer was characterized using in situ soft-contact atomic force microscopy, and micelle-like surface aggregates are clearly observed within each layer of the complex film, suggesting the persistence of aggregate structures throughout the multilayer structure.     

pH-responsive aqueous foams stabilized by hairy latex particles

Polystyrene (PS) latex particles carrying pH-responsive poly[2-(diethylamino)ethyl methacrylate] (PDEA) hair (PDEA-PS particles) were synthesized by dispersion polymerization and characterized in terms of diameter, diameter distribution, morphology, chemical composition, surface chemistry, and pH-response using scanning electron microscopy (SEM), elemental microanalysis, (1)H nuclear magnetic resonance spectroscopy, the laser diffraction method, and zeta potential measurements. The hairy particles can act as pH-responsive stabilizers of aqueous foams by adsorption at the air-water surface. Above pH 8.0, where particles have nonprotonated PDEA hair, which is relatively hydrophobic, particle-stabilized foams are stable for at least 1 month. Optical microscopy and SEM confirmed that flocculated PDEA-PS latex particles were adsorbed at the air-water interface and stabilized the aqueous foams. At pH 6.1 and 7.1, relatively stable foams can be prepared that remain stable for at least 24 h. SEM studies indicated that the PDEA-PS particles were adsorbed at the air-water interface as a monolayer at pH 6.1. At pH 5.1 and 3.1, where the particles have cationic water-soluble PDEA hairs with hydrophilic character, no foam was formed. Rapid defoamation can be induced by lowering the solution pH; the addition of acid caused the in situ protonation of 2-(diethylamino)ethyl methacrylate residues, which impart water-soluble hydrophilic character to the PDEA hair, and the PDEA-PS particles desorbed from the air-water interface. The foaming and defoaming cycles could be repeated at least five times.     

Incorporation of block copolymer micelles into multilayer films for use as nanodelivery systems

This work demonstrates the potential application of stimulus responsive block copolymer micelles as triggerable delivery systems for use within multilayer films. Cationic, pH-responsive micelles of poly[2-(dimethylamino)ethyl methacrylate-block-poly(2-(diethylamino)ethyl methacrylate)] (PDMA-PDEA) were deposited on anionic polystyrene latex particles. The charge reversal of the surface and the amount of adsorbed polymer were monitored by zeta potential measurements and colloidal titrations, respectively. Prior to adsorption, the PDMA-PDEA micelles were loaded with a hydrophobic dye, and UV-vis spectroscopy was used to determine the amount of dye encapsulated within a monolayer of micelles. It was found that subtle chemical modification of the PDMA-PDEA diblock copolymer via permanent quaternization of the PDEA block results in micelles with tunable loading capacities. Multilayers of cationic micelles of partially quaternized PDMA-PDEA and anionic polyelectrolyte (poly(sodium 4-styrene sulfonate)) were deposited on the surface of polystyrene latex particles by sequential adsorption. UV-vis analysis of the dye present within the multilayer after the addition of each layer demonstrates that the micelles are sufficiently robust to retain encapsulated dye after multiple adsorption/washing cycles and can thus create a film that can be increasingly loaded with dye as more micelle layers are adsorbed. Multiple washing cycles were performed on micellar monolayers of PDMA-PDEA to demonstrate how such systems can be used to bring about triggerable release of actives. When performing several consecutive washing steps at pH 9.3, the micelle structure of the PDMA-PDEA micelles in the monolayer is retained, resulting in only a small reduction in the amount of encapsulated dye. In contrast, washing at pH 4, the structure of the micelle layers is severely disrupted, resulting in a fast release of the encapsulated dye into the bulk. Finally, if a sufficient number of micelle/homopolyelectrolyte layers are adsorbed, it is possible to selectively dissolve the latex template, resulting in hollow capsules.     

Effect of varying the oil phase on the behavior of pH-responsive latex-based emulsifiers: demulsification versus transitional phase inversion

Sterically stabilized polystyrene latexes (previously described by Amalvy, J. I.; et al. Chem. Commun. 2003, 1826) were evaluated as pH-responsive particulate emulsifiers for the preparation of both oil-in-water and water-in-oil emulsions. The steric stabilizer was a well-defined AB diblock copolymer where A is poly(2-(dimethylamino)ethyl methacrylate) and B is poly(methyl methacrylate). Several parameters were varied during the emulsion preparation, including the polarity of the oil phase, the latex concentration, surface concentration of copolymer stabilizer, and solution pH. Nonpolar oils such as n-dodecane gave oil-in-water emulsions, and polar oils such as 1-undecanol produced water-in-oil emulsions. In both cases, these emulsions proved to be stimulus-responsive: demulsification occurred rapidly on adjusting the solution pH. Oils of intermediate polarity such as methyl myristate or cineole led to emulsions that underwent transitional inversion on adjusting the solution pH. All emulsions were polydisperse and typically ranged from 40 to 400 microm diameter, as judged by optical microscopy and Malvern Mastersizer measurements. Critical point drying of the emulsion droplets, followed by scanning electron microscopy studies, confirmed that the latex particles were adsorbed as a single monolayer at the oil/water interface, as anticipated.     

Cross-linking of cationic block copolymer micelles by silica deposition

Diblock copolymer micelles comprising cationic poly(2-(dimethylamino)ethyl methacrylate) (PDMA) coronas and hydrophobic poly(2-(diisopropylamino)ethyl methacrylate) (PDPA) cores are used as nanosized templates for the deposition of silica from aqueous solution at pH 7.2 and 20 degrees C. Both noncross-linked and shell cross-linked (SCL) micelles can be coated with silica without loss of colloid stability. Under optimized conditions, the silica deposition is confined to the partially quaternized cationic PDMA chains, leading to hybrid copolymer-silica particles of around 35 nm diameter with well-defined core-shell morphologies. 1H NMR studies confirmed that the PDPA cores of these copolymer-silica particles became protonated at low pH and deprotonated at high pH, which suggests possible encapsulation and controlled release applications. Moreover, in situ silica deposition effectively stabilizes the PDPA-PDMA micelles, which remain intact on lowering the solution pH (whereas the original noncross-linked PDPA-PDMA micelles dissociate in acidic solution). This suggests a convenient route to silica-stabilized SCL micelles under mild conditions.     

Novel Pickering Emulsifiers based on pH-Responsive Poly(tert-butylaminoethyl methacrylate) Latexes

Emulsion copolymerization of 2-(tert-butylamino)ethyl methacrylate in the presence of divinylbenzene (DVB) cross-linker and monomethoxy-capped poly(ethylene glycol) methacrylate (PEGMA) macromonomer at 70 °C afforded sterically-stabilized latexes at approximately 10% solids at pH 9. Dynamic light scattering and scanning electron microscopy (SEM) confirmed that relatively narrow size distributions were obtained. SEM confirmed the formation of spherical particles in the absence of any DVB cross-linker using a simple batch protocol, but in the presence of DVB it was necessary to use seeded emulsion polymerization under monomer-starved conditions to prevent the formation of latexes with ill-defined non-spherical morphologies. Lightly cross-linked latexes acquired cationic microgel character upon lowering the solution pH due to protonation of the secondary amine groups. Increasing the degree of cross-linking led to a progressively lower effective pK(a) of the copolymer chains from 8.0 to 7.3, which implies a gradual reduction in their basicity. Poly(tert-butylamino)ethyl methacrylate latex proved to be an effective Pickering emulsifier at pH 10, forming stable oil-in-water emulsions when homogenized with either n-dodecane or sunflower oil at 12?000 rpm for 2 min. These Pickering emulsions exhibited pH-responsive behavior: lowering the solution pH to 3 resulted in immediate demulsification due to the spontaneous desorption of the cationic microgels from the oil/water interface. Following rehomogenization at high pH, four successive demulsification/emulsification pH cycles could be achieved without a discernible loss in performance. However, no demulsification occurred on acidification of the fifth cycle, due to the progressive build-up of background salt.     

Adsorption characteristics of zwitterionic diblock copolymers at the silica/aqueous solution interface

The adsorption of a zwitterionic diblock copolymer, poly(2-(diethylamino)ethyl methacrylate)-block-poly(methacrylic acid) (PDEA59-PMAA50), at the silica/aqueous solution interface has been characterised as a function of pH. In acidic solution, this copolymer forms core-shell micelles with the neutral PMAA chains being located in the hydrophobic cores and the protonated PDEA chains forming the cationic micelle coronas. In alkaline solution, the copolymer forms the analogous inverted micelles with anionic PMAA coronas and hydrophobic PDEA cores. The morphology of the adsorbed layer was observed in situ using soft-contact atomic force microscopy (AFM): this technique suggests the formation of a thin adsorbed layer at pH 4 due to the adsorption of individual copolymer chains (unimers) rather than micelle aggregates. This is supported by the remarkably low dissipation values and the relatively low degrees of hydration for the adsorbed layers, as estimated using a combination of quartz crystal microbalance with dissipation monitoring (QCM-D) and optical reflectometry (OR). In alkaline solution, analysis of the adsorption data suggests a conformation for the adsorbed copolymers where one block projects normal to the solid/liquid interface; this layer consists of a hydrophobic PDEA anchor block adsorbed on the silica surface and an anionic PMAA buoy block extending into the solution phase. Tapping mode AFM studies were also carried out on the silica surfaces after removal from the copolymer solutions and subsequent drying. Interestingly, in these cases micelle-like surface aggregates were observed from both acidic and alkaline solutions. The lateral dimension of the aggregates seen is consistent with the corresponding hydrodynamic diameter of the copolymer micelles in bulk solution. The combination of the in situ and ex situ AFM data provides evidence that, for this copolymer, micelle aggregates are only seen in the ex situ dry state as a result of the substrate withdrawal and drying process. It remains unclear whether these aggregates are caused by micelle deposition at the surface during the substrate withdrawal from the solution or as a result of unimer rearrangements at the drying front as the liquid recedes from the surface.     

Comparison of the adsorption of cationic diblock copolymer micelles from aqueous solution onto mica and silica

The similarities and differences in the adsorption behavior of diblock poly(2-(dimethylamino)ethyl methacrylate)-b-poly(2-(diethylamino)ethyl methacrylate) (XqPDMA-PDEA, where X refers to a mean degree of quaternization of the PDMA of either 0, 10, 50, or 100 mol%) copolymers at the mica/ and silica/aqueous solution interfaces have been investigated. These diblock copolymers form core-shell micelles with the PDEA chains located in the cores and the more hydrophilic PDMA chains forming the cationic micelle coronas at pH 9. These micelles adsorb strongly onto both mica and silica due to electrostatic interactions. In situ atomic force microscopy (AFM) has demonstrated that the mean spacing and the dimension of the adsorbed micelles depend on both the substrate and the mean degree of quaternization of the PDMA blocks. In particular, the morphology of the adsorbed nonquaternized 0qPDMA-PDEA copolymer micelles is clearly influenced by the substrate type: these micelles form a disordered layer on silica, while much more close-packed, highly ordered layers are obtained on mica. The key reasons for this difference are suggested to be the ease of lateral rearrangement for the copolymer micelles attached to the solid substrates and the relative rates of relaxation of the coronal PDMA chains.     

Solution pH-regulated interfacial adsorption of diblock phosphorylcholine copolymers

Spectroscopic ellipsometry has been used to examine the pH-responsive interfacial adsorption of a series of biocompatible diblock copolymers incorporating 2-methacryloyloxyethyl phosphorylcholine-based (MPC) residues and 2-(dialkylamino)ethyl methacrylate residues, with a specific focus on 2-(diethylamino)ethyl groups (referred to as MPCm-DEAn, where m and n refer to the mean degrees of polymerization of each block) at the hydrophilic silicon oxide/water interface. For all the copolymers studied the surface excess shows only weak concentration dependence. Increasing the length of the DEA block has little effect on the dynamic or equilibrated adsorption at pH 7, indicating that the DEA block adopts a flat conformation on the silicon oxide surface at this pH. With increasing pH, however, the surface excess shows a dramatic increase, followed by a subsequent decline. The observed maximum in surface excess represents a balance between charge over-compensation of the copolymer with the oppositely charged surface and the subsequently reduced charge density of the copolymer. Variations in the observed maxima for various MPCm-DEAn diblock copolymers indicate different surface conformations at high pH. Salt addition does not affect copolymer adsorption. This behavior is attractive for biomedical applications in which the ionic strength is variable. It was also found that the preadsorbed diblock copolymers immobilized DNA from solution to an extent that is proportional to the relative charge ratio between the anionic DNA and the cationic DEA block of the copolymer.     

A physico-chemical investigation of poly(ethylene oxide)-block-poly(L-lysine) copolymer adsorption onto silica nanoparticles

The adsorption behavior of poly(ethylene oxide)-b-poly(L-lysine) (PEO(113)-b-PLL(10)) copolymer onto silica nanoparticles was investigated in phosphate buffer at pH 7.4 by means of dynamic light scattering, zeta potential, adsorption isotherms and microcalorimetry measurements. Both blocks have an affinity for the silica surface through hydrogen bonding (PEO and PLL) or electrostatic interactions (PLL). Competitive adsorption experiments from a mixture of PEO and PLL homopolymers evidenced greater interactions of PLL with silica while displacement experiments even revealed that free PLL chains could desorb PEO chains from the particle surface. This allowed us to better understand the adsorption mechanism of PEO-b-PLL copolymer at the silica surface. At low surface coverage, both blocks adsorbed in flat conformation leading to the flocculation of the particles as neither steric nor electrostatic forces could take place at the silica surface. The addition of a large excess of copolymer favoured the dispersion of flocs according to a presumed mechanism where PLL blocks of incoming copolymer chains preferentially adsorbed to the surface by displacing already adsorbed PEO blocks. The gradual addition of silica particles to an excess of PEO-b-PLL copolymer solution was the preferred method for particle coating as it favoured equilibrium conditions where the copolymer formed an anchor-buoy (PLL-PEO) structure with stabilizing properties at the silica-water interface.     

无机盐对氟烷基封端的嵌段共聚物在水相聚集行为的影响

以含氟醇钾盐(NFHO-K )作为引发剂,通过阴离子活性聚合方法合成了氟烷基封端的聚甲基丙烯酸-2-(二甲氨基)乙酯-block-聚甲基丙烯酸-2-(二乙氨基)乙酯嵌段共聚物(NFHO-PDMA-b-PDEA).该共聚物与一般的含氟嵌段共聚物相比,既具有优良的表面活性,又具有较好的溶解性.通过对溶液表面张力的测定,荧光探针法对溶液临界聚集浓度(cac)的测定和透射电子显微镜(TEM)对共聚物在溶液中胶束形态的研究,发现无机盐对共聚物在水溶液中的聚集行为有明显的影响,并可以增强共聚物的表面活性.     

A novel cationic triblock copolymer as noncovalent coating for the separation of proteins by CE

A novel noncovalent adsorbed coating for CE has been prepared and explored. This coating was based on quaternized poly(2-(dimethylamino)ethyl methacrylate)-block-poly(ethylene oxide)-block-poly(2-(dimethylamino)ethyl methacrylate) (QDED) triblock copolymer which was synthesized by atomic transfer radical polymerization (ATRP) in our laboratory. The polycationic polymer and the negatively charged fused-silica surface attracted each other through electrostatic interactions and hydrogen bonds. It was demonstrated that the coated capillaries provided an electroosmotic flow with reverse direction, and the magnitude of the electroosmotic flow can be modulated by varying the molecular mass of poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) block and pH value of the buffer. The effects of the molecular mass of PDMAEMA block in QDED triblock copolymer and pH value of the buffer on the separation of basic proteins were investigated in detail. The triblock copolymer coatings showed higher separation efficiency, better migration time repeatability and would apply to wider range of pH than bare fused-silica capillary when used in separating proteins. Proteins from egg white were also separated through this QDED triblock copolymer-coated capillary. These results demonstrated that the QDED triblock copolymer coatings are suitable for analyzing biosamples.     

Stimuli-responsive surfaces using polyampholyte polymer brushes prepared via atom transfer radical polymerization

The synthesis of AB diblock copolymer polyampholyte polymer brushes of the type Si/SiO2//poly(acrylic acid-b-vinyl pyridine) prepared using atom transfer radical polymerization is reported. Both 2- and 4-vinyl pyridine have been used. The diblock polyampholyte polymer brushes demonstrate stimuli-responsive behavior with respect to pH, showing both polyelectrolyte and polyampholyte effects. Furthermore, we have quaternized the 4-vinyl pyridine segments to form a mixed weak/strong, or annealed/quenched, polyelectrolyte system. The quaternized polymer brush exhibits different pH-responsive behavior, with decreasing film thickness being observed with increasing pH.     

Synthesis and characterization of novel pH-responsive microgels based on tertiary amine methacrylates

Emulsion polymerization of 2-(diethylamino)ethyl methacrylate (DEA) in the presence of a bifunctional cross-linker at pH 8-9 afforded novel pH-responsive microgels of 250-700 nm diameter. Both batch and semicontinuous syntheses were explored using thermal and redox initiators. Various strategies were evaluated for achieving colloidal stability, including charge stabilization, surfactant stabilization, and steric stabilization. The latter proved to be the most convenient and effective, and three types of well-defined reactive macromonomers were examined, namely, monomethoxy-capped poly(ethylene glycol) methacrylate (PEGMA), styrene-capped poly[2-(dimethylamino)ethyl methacrylate] (PDMA50-St), and partially quaternized styrene-capped poly[2-(dimethylamino)ethyl methacrylate] (10qPDMA50-St). The resulting microgels were pH-responsive, as expected. Dynamic light scattering and 1H NMR studies confirmed that reversible swelling occurred at low pH due to protonation of the tertiary amine groups on the DEA residues. The critical pH for this latex-to-microgel transition was around pH 6.5-7.0, which corresponds approximately to the known pKa of 7.0-7.3 for linear PDEA homopolymer. The microgel particles were further characterized by electron microscopy and aqueous electrophoresis studies. Their swelling and deswelling kinetics were investigated by turbidimetry. The PDEA-based microgels were compared to poly[2-(diisopropylamino)ethyl methacrylate] (PDPA) microgels prepared with identical macromonomer stabilizers. These PDPA-based microgels had a lower critical swelling pH of around pH 5.0-5.5, which correlates with the lower pKa of PDPA homopolymer. In addition, the kinetics of swelling for the PDPA microgels was somewhat slower than that observed for PDEA microgels; presumably this is related to the greater hydrophobic character of the former particles.     

Autonomous Volume Transitions of a Polybase Triblock Copolymer Gel in a Chemically Driven pH-Oscillator

Summary: A pH-responsive ABA triblock copolymer, comprising poly(methyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate)-block-poly(methyl methacrylate) [PMMA-b-PDEA-b-PMMA], has been cast into thin films with a well-defined microstructure. Small Angle X-ray Scattering (SAXS) and Atomic Force Microscopy (AFM) studies confirm that this copolymer forms a hydrogel consisting of PMMA spheres embedded within a polybase PDEA matrix, with the PMMA domains acting as physical cross-links. The hydrogel has a pH-reversible coil-globule transition at around pH 4.5. This responsive physical property was exploited by immersing a sample of copolymer hydrogel in an aqueous solution containing a cyclic pH-oscillating reaction, whereby the pH was continuously oscillated above and below the transition pH so as to induce autonomous volume transitions. The changes in microscopic and macroscopic length scales correlate closely during (de)swelling cycles, with affine behaviour occurring over five orders of magnitude.