分隔板偏角对圆柱受力和脱涡频率的影响

钝体后安装分隔板是一种有效的被动控制技术,本文采用有限体积法对非稳态二维层流下的圆柱-分隔板结构绕流进行了数值计算。研究了中等雷诺数（Re=100～500）下,分隔板与来流方向存在夹角时（θ=0°～45°）的圆柱绕流特性。结果表明不同Re数下,圆柱阻力和升力系数等反映流动特性的参数随分隔板偏角而变化;阻力系数最小值对应...     

过渡流下顺排双列圆柱流动、传热特性的数值研究

为了研究过渡流状态下管束传热强化机理,通过基于复合网格的专用程序,本文建立了顺排布置双列管束计算模型。计算结果表明:1)两列圆柱之间的流场结构分为稳定结构(对称死区)和非稳定结构(旋涡),非稳定结构的流场下的下列圆柱传热效率高于稳定结构流场的传热效率。2)由于旋涡的出现,在一定的横向间距内,传热效率升高速率要大于流动阻力升高的速率,大于这个横向间距后,情况相反,这一结果肯定了旋涡不稳定性对下游圆柱壁面传热强化的影响.3)随着纵向间距的缩小,涡脱频率升高,两列圆柱之间流体被加速,加速了旋涡的发展,这能在更小的横向间距内,率先使传热效率升高。     

动态长度下压力交换器内脉动掺混研究

建立压力能交换器的二维非稳态数值模型,研究了进流速度v、斯特劳哈尔数St以及脉动幅度A等对孔道内旋涡运动和掺混区形成的影响。结果表明,旋涡周期性脱落是掺混区形成的主要原因,涡强越大掺混越严重;St数的增大以及A的减小将使孔道内旋涡强度增强;St数的增大将使尺寸效应明显,掺混受涡强影响小,因而对于一定孔道存在最优的运行St数。并且随着A的增大,掺混区的稳定性变强,孔道的最优运行St数减小。     

基于POD方法开缝圆柱绕流流场的研究

利用粒子成像测速技术（particle image velocimetry,PIV）,在水槽中探究缝隙对圆柱流场结构的影响,应用频谱分析和本征正交分解（proper orthogonal decomposition,POD）方法,研究了开缝圆柱流场相干结构.实验Reynolds数范围内,缝隙的"吹吸"作用从根本上改变了圆柱绕流近区尾流结构,前6阶模态形态是流场中最主要的相干结构.第1,2阶模态形态控制着圆柱绕流流场涡街相继脱落过程,1或2阶模态系数为尾迹涡的固有频率;第3,4阶模态形态控制着脱落旋涡沿流向方向能量运输;第5,6阶模态形态中的同向涡旋结构作用于旋涡缓慢脱离柱体这一过程,并对旋涡能量起着衰减作用.      

空间发展湍流气粒两相平面混合层的大涡模拟与统计

本文对空间发展的湍流气固两相平面混合层流动进行了大涡模拟研究,其中气相亚网格尺度（SGS）使用结构函数模型,气相控制方程组采用SIMPLE方法求解,固体颗粒运动用拉格朗日方法计算。计算结果正确重现了流体涡结构的卷起、合并和破碎过程,以及小尺寸颗粒在涡边缘（低涡度区）的局部富集现象。对直径分别为42μm、72μm和135μm分别进行了模拟,并将统计结果和实验测量结果（Hishida　et　al[1]）比较,表明两者的平均速度吻合很好,但颗粒数密度和脉动速度存在较明显的差异,因此有必要对亚网格应力和颗粒之间的耦合作用以及拟序结构的三维性对颗粒运动的影响开展深入研究。     

气固两相三维圆柱绕流的直接数值模拟

本文采用直接数值模拟(DNS)方法研究了气周两相三维圆柱绕流的涡量场和颗粒扩散,并着重讨论了圆柱绕流中卡门涡街的形成和涡结构的转捩过程。同时分析了圆柱绕流中不同Stokes数的颗粒在涡结构作用下的横向扩散。结果显示Stokes数为1的颗粒主要分布在流场大尺度涡结构的外边界,而Stokes数为0．01的颗粒在涡结构的作用下,在流场中充分混合。     

溶解与热对流对固体颗粒运动影响的直接数值模拟

对牛顿流体内溶解与热对流对单颗粒在垂直管道中的沉降运动进行了直接数值模拟.流体运动由守恒方程计算,密度和黏性的变化考虑流场温度变化的影响,通过积分黏性应力和压力获得颗粒的受力跟踪颗粒运动,溶解引起的相变及其形状的变化由溶解潜热、溶解质量与分散相边界处的温度梯度的关系建立的方程决定.通过颗粒和流体间相互的作用力和力矩及边界条件的施加实现相间耦合.分别模拟了颗粒在等温流体、热流体、冷流体及颗粒溶解四种情况下的沉降过程.结果表明,在一定雷诺数内,热对流产生的颗粒尾迹处涡的脱落以及溶解引起的颗粒表面形态的变化引起了颗粒的横向摆动,并使颗粒沉降速度发生了变化. 关键词： 溶解 热对流 颗粒两相流 直接数值模拟     

基于有限体积虚拟区域方法的两相流动直接模拟

为提高计算效率，提出有限体积法离散下的虚拟区域颗粒两相流动直接模拟方法.在控制方程中加入相应的虚拟区域源项，保证了颗粒内部的刚体运动特性.该源项中含有颗粒信息部分及流体信息部分.在每次迭代后，对源项中的流体信息部分进行更新，从而更好地保证颗粒内速度的刚体分布.计算静止颗粒圆柱绕流及单个颗粒的沉降过程，验证了算法的准确性.     

微尺度串列双圆柱绕流的分子动力学并行模拟

本文采用基于空间分解算法的分子动力学并行模拟方法,研究了微尺度、低雷诺数（Re=40）下串列等大的双圆柱绕流现象。结果表明：随着间距比L＊／D＊的增加,流动存在3种特征状态：当L＊／D＊〈1．1时,同单一物体的绕钝体流动相似;当1．1〈L＊／0＊〈3．5时,涡脱落现象只在下游圆柱出现,在两圆柱之间有交替附着于下游圆柱的...     

双颗粒在溶解条件下沉降的多相流动特性

对牛顿流体内溶解双颗粒在垂直管道中的沉降运动进行了直接数值模拟. 流体运动由守恒方程计算, 密度和黏性的变化考虑流场温度变化的影响, 通过积分粘性应力和压力获得颗粒的受力跟踪颗粒运动, 溶解引起的相变及其形状的变化由溶解潜热、溶解质量与分散相边界处的温度梯度的关系建立的方程决定. 通过颗粒和流体间相互的作用力和力矩及边界条件的施加实现相间耦合. 对双颗粒在等温流体无溶解条件和非等温流体溶解条件下的沉降过程进行了计算. 结果表明, 在一定雷诺数内, 热对流产生的颗粒尾迹处涡的脱落以及溶解引起的颗粒质量、颗粒表面形态的变化引起了颗粒的横向摆动, 并使颗粒沉降速度发生了变化.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.