Simultaneous removal of uranium and humic acid by cyclodextrin modified graphene oxide nanosheets

Cyclodextrin-modified graphene oxide nanosheets (denoted as CD/GO) were synthesized by an in-situ polymerization method and characterized by as well as Fourier transform-infrared spectroscopy, X-ray photoelectron spectroscopy, Raman spectroscopy and potentiometric acid-base titration. The characterization results indicated that CD was successfully grafted onto GO surfaces by forming a chemical bond. Mutual effects on the simultaneous removal of hexavalent uranium and humic acid by CD/GO from aqueous solution were investigated. The results indicated that U(VI) and humic acid (HA) sorption on CD/GO were greatly affected by pH and ionic strength. The presence of HA enhanced U(VI) sorption at low pH and reduced U(VI) sorption at high pH, whereas the presence of U(VI) enhanced HA sorption. The surface adsorbed HA acted as a “bridge” between U(VI) and CD/GO, and formed strong inner-sphere surface complexes with U(VI). Sorption isotherms of U(VI) or HA on CD/GO could be well fitted by the Langmuir model. This work highlights that CD/GO can be used as a promising material in the enrichment of U(VI) and HA from wastewater in U(VI) and humic substances obtained by environmental pollution cleanup.     

Adsorption properties of amidoximated porous acrylonitrile/methyl acrylate copolymer beads for Ag (I)

Porous a crylonitrile (AN)/methyl acrylate (MA) copolymer beads were synthesized by suspended emulsion polymerization and amidoximated for the purpose of Ag⁺ adsorption. Optimum amidoximation temperature and time were determined by following the adsorption capacity for Ag⁺. The results showed that amidoximated AN/MA (AO AN/MA) with the amidoximation temperature 70°C and amidoximation time 20 hr had a relatively higher adsorption capacity for Ag⁺. The effect of pH on adsorption for Ag⁺ was studied; the highest adsorption capacity presented at pH 5.0. Adsorption kinetics and isotherms of AO AN/MA copolymer beads for Ag⁺ were also investigated. The kinetics data indicated that the adsorption process was governed by the film diffusion and followed both pseudo‐first‐order and pseudo‐second‐order rate model. The isotherms indicated that adsorption capacities increased with equilibrium concentration and temperature. The Langmuir model and Sips model could describe the isothermal process. Thermodynamic analysis revealed that the adsorption behaviors of Ag⁺ ions on AO AN/MA could be considered as endothermic and physical sorption process. Copyright © 2010 John Wiley & Sons, Ltd.     

Adsorption of Zn(II) on graphene oxide prepared from low‐purity of amorphous graphite

The adsorption of Zn(II) in aqueous solutions on graphene oxide (GO) prepared from low‐purity of natural amorphous graphite has been studied in this work. The study was performed through the measurements of Zeta potential, atomic force microscope, Fourier transform infrared spectrum and X‐ray photoelectron spectroscopy. The results indicated that the adsorption followed the Langmuir model with the maximum Zn(II) adsorption capacity of 73 mg/g at pH 7.0. In addition, the adsorption was well described by the pseudo‐second‐order kinetics model. The mechanism of the Zn(II) adsorption on GO was mainly attributed to chemical adsorption through complexation reaction between Zn(II) and hydroxyl or carboxyl groups on the GO sheets, while the electrostatic interaction also contribute to the whole interaction. Copyright © 2016 John Wiley & Sons, Ltd.     

Atom transfer radical polymerization with activators regenerated by electron transfer of acrylonitrile from silica nanoparticles,and adsorption properties of the resin for Hg2+ after amidoximation with hydroxylamine

Polyacrylonitrile (PAN) was grafted from surfaces of chloro‐modified silica‐gel with their surface chlorines as initiation sites, using an iron (III)‐mediated surface‐initiated atom transfer radical polymerization (ATRP) with activators regenerated by electron transfer (SI‐ARGET ATRP) method. The graft reaction exhibits first‐order kinetics with respect to the polymerization time in the low‐monomer‐conversion stage. The conversion of monomer (C%) and the percentage of grafting (PG%) increased with increasing of the polymerizing time and reached 23 and 730% after a polymerizing time of 24 hr, respectively. Hydroxylamine (NH₂OH·HCl) was used to modify the cyano groups of SG‐g‐PAN to obtain amidoxime (AO) groups. The AO SG‐g‐PAN was used to remove Hg²⁺. The adsorption kinetics indicated that the pseudo‐second‐order model was more suitable to describe the adsorption kinetics of AO SG‐g‐PAN for Hg²⁺. The adsorption isotherms demonstrated that Langmuir model was much better than Freundlich model to describe the isothermal process. Copyright © 2010 John Wiley & Sons, Ltd.     

Poly(ionic liquid)s as phase-transporter for graphene oxide liquid crystals from aqueous to non-polar organic phase via noncovalent functionalization

We synthesise a novel poly(ionic liquid) (PIL) and develop a procedure that allows the phase transfer of graphene oxides (GO) from water to organic solvent, retaining graphene oxide liquid crystal (GOLC) phase in various organic solvents, especially non-polar organic solvents. PIL ([PEP-MIM]DBS) is exploited in this procedure as a noncovalent functional material that is capable of transporting GO from aqueous to non-polar organic phase. PILs can decorate GO noncovalently and keep GO nano-sheets exfoliated in solid-state PILs/GO hybrids, which can well redisperse in organic solvents without any agglomeration. This expands the number of known solvents which can support GOLC phase to dimethyl formamide, dimethyl sulfoxide, acetonitrile, tetrahydrofuran, and a number of other non-polar organic solvents, many of which were not known to afford GOLC phase prior to this report, such as dichloromethane, tetrachloromethane, dichloroethane and tetrachloroethane.     

纳米纤维素/还原氧化石墨烯复合材料用于高性能超级电容器

以高浓度氧化石墨烯(GO)溶液作为反应前驱体,纳米纤维素(NC)作为物理间隔物和电解液储存器,通过简单的一步水热法制备了纳米纤维素/还原氧化石墨烯(NC/rGO)复合材料,并探究了其作为超级电容器电极材料的潜力。结果如下：NC添加量为1 mL所制备的NC/rGO-1具有最佳电化学性能。基于NC/rGO-1的无黏合剂对称型超级电容器在0.3 A·g^-1的电流密度下显示出了269.33 F·g^-1和350.13 F·cm^-3的高质量和体积比电容,并在10.0 A·g^-1时仍能达到215.88 F·g^-1和280.62 F·cm^-3(其初始值的80.15%)。组装器件还显示出了较高的质量和体积能量密度(9.3 Wh·kg^-1和12.13 Wh·L^-1)和出色的循环性能(10 A·g^-1下10 000次循环后其初始比电容仅减少6.02%)。     

Poly(N‐vinylcarbazole) chemically modified graphene oxide

A new soluble donor‐acceptor type poly(N‐vinylcarbazole)‐covalently functionalized graphene oxide (GO‐PVK) has been synthesized by reaction of DDAT (S‐1‐dodecyl‐S′‐(α,α′‐dimethyl‐α″‐aceticacid)trithiocarbonate)‐PVK with GO‐toluene‐2,4‐diisocynate. The incorporation of sufficient amount of PVK chains makes the modified GO nanosheets readily dispersible in organic solvents. The resulting material exhibits an enhanced solubility of 10 mg/mL in organic solvents. Covalent grafting of PVK onto the edge and surface of GO nanosheets did not change the carbazole absorption in the ultraviolet region, but substantially reduced the absorption intensity of GO in the visible region. The intensity of the emission band of GO‐PVK at 437 nm was a little bit quenched when compared with that of DDAT‐PVK, suggesting intramolecular quenching from PVK to GO. Such intramolecular quenching process may involve energy or electron transfer between the excited singlet states of the PVK moiety and the GO moiety. The HOMO/LUMO values and the energy bandgap of GO‐PVK experimentally estimated by the onset of the redox potentials are ?5.60, ?3.58, and 2.02 eV, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2642–2649, 2010     

纳米纤维素/还原氧化石墨烯复合材料用于高性能超级电容器

以高浓度氧化石墨烯(GO)溶液作为反应前驱体,纳米纤维素(NC)作为物理间隔物和电解液储存器,通过简单的一步水热法制备了纳米纤维素/还原氧化石墨烯(NC/rGO)复合材料,并探究了其作为超级电容器电极材料的潜力。结果如下：NC添加量为1 mL所制备的NC/rGO-1具有最佳电化学性能。基于NC/rGO-1的无黏合剂对称型超级电容器在0.3 A·g^-1的电流密度下显示出了 269.33 F·g^-1和 350.13 F·cm^-3的高质量和体积比电容,并在 10.0 A·g^-1时仍能达到 215.88 F·g^-1和 280.62 F·cm^-3(其初始值的 80.15%)。组装器件还显示出了较高的质量和体积能量密度(9.3 Wh·kg^-1和 12.13 Wh·L^-1)和出色的循环性能(10 A·g^-1下10 000次循环后其初始比电容仅减少6.02%)。     

A disposable electrochemical sensor for the determination of indole-3-acetic acid based on poly(safranine T)-reduced graphene oxide nanocomposite

A disposable electrochemical sensor for the determination of indole-3-acetic acid (IAA) based on nanocomposites of reduced graphene oxide (rGO) and poly(safranine T) (PST) was reported. The sensor was prepared by coating a rGO film on a pre-anodized graphite electrode (AGE) through dipping-drying and electrodepositing a uniform PST layer on the rGO film. Scanning electron microscopic (SEM) and infrared spectroscopic (IR) characterizations indicated that PST-rGO formed a rough and crumpled composite film on AGE, which exhibited high sensitive response for the oxidation of IAA with 147-fold enhancement of the current signal compared with bare AGE. The voltammetric current has a good linear relationship with IAA concentration in the range 1.0 × 10⁻⁷-7.0 × 10⁻⁶ M, with a low detection limit of 5.0 × 10⁻⁸ M. This sensor has been applied to the determination of IAA in the extract samples of several plant leaves and the recoveries varied in the range of 97.71-103.43%.     

Poly(amidoxime) functionalized MoS2 for efficient adsorption of uranium(VI) in aqueous solutions

Journal of Radioanalytical and Nuclear Chemistry - A novel adsorbent for enrichment of trace uranium (U(VI)) ions in aqueous solution is designed based on the excellent adsorption capacity of...     

功能化的石墨烯和磁铁掺杂的还原氧化石墨烯对亚甲基蓝的吸附作用

用简单可行的方法合成了功能化的石墨烯(GNSPF6)和磁铁掺杂的还原氧化石墨烯(RGO-Fe3O4),并进一步研究了pH值、接触的时间和温度对它们吸附亚甲基蓝(MB)的影响.结果表明,随着pH值和温度的增加其吸附量也随之变大,从而说明该吸附过程是自发吸热的.因为GNSPF6的吸附过程只用了不到20min的时间,所以它的吸附是高效的.用经典的准一级反应、准二级反应和粒内扩散模型对其吸附过程进行动态分析,从结果可以发现,准二级动力学模型比准一级动力学模型更适用于描述吸附过程.采用传统的Langmuir,Freundlich和L-F吸附等温线模型来模拟分析数据,在20℃时,由Langmuir吸附等温线模型模拟分析得知GNSPF6和RGO-Fe3O4对MB的最大吸附量分别为374.4和118.4mg/g.     

Hydrothermal leather waste by hydrothermal method for uranium (VI) removal from a Simulated Saline Solution

Hydrothermal leather waste was prepared by hydrothermal method, using leather waste as the precondition and applying the adsorption of uranium (VI) in solution. The effects of pH value, adsorption time and initial concentration of uranium (VI) on the adsorption efficiency were investigated. The adsorption process was in accordance with the pseudo‐second‐order kinetic model and Freundlich adsorption isotherm model. Kinetic and thermodynamic studies showed that the adsorption process was endothermic and spontaneous, and it reached adsorption equilibrium in 240 min. In the simulated high salinity environment, the adsorbent exhibited excellent adsorption rate on the trace of uranium (VI). The adsorbent was characterized by scanning electron microscopy, flourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy, and it was found that the adsorption mechanism was coordinated complex.     

Glycine‐functionalized reduced graphene oxide for methylene blue removal

Glycine‐functionalized reduced graphene oxide (GRGO) was prepared through the reaction of glycine and chlorine‐functionalized reduced graphene oxide. The product was characterized by SEM, HRTEM, IR, Raman, and XPS. The nitrogen content (8.28%) was high in product, peak at 285.8 eV was assigned to the C–N bond, which implied that the chlorine residues in raw material were substituted by amine group of glycine. The intensity ratio of D and G peak was about 1.5, which also implied that more saturated carbon atoms were present in the product. Results of SEM, IR, and XPS confirmed that glycine molecules were attached to graphene sheets. Compared with reduced graphene oxide (61.5 mg/g) and active carbon (45.2 mg/g), GRGO had a good adsorption capacity (98.9 mg/g) for methylene blue. The adsorption process was fitted to three kinetic models and three adsorption isotherm models. The adsorption process complied with pseudo‐second order kinetic model and Langmuir model.     

Efficiently removing cetyl trimethyl ammonium bromide from wastewater by graphene oxide

Cetyl trimethyl ammonium bromide (CTAB) containing wastewater from dressing plant may pose a detrimental threaten to mineral beneficiation and environment. The adsorption of CTAB in aqueous solutions by graphene oxide (GO) has been studied in this work. X-ray diffraction, X-ray photoelectron spectroscopy, Fourier-transform infrared spectrometer, and atomic force spectroscopy were used to characterize GO. The results indicated that the adsorption followed the Freundlich model could be well described by pseudo-second order kinetic model. The adsorption capacity was much bigger than activated carbon and many natural clay minerals. The adsorption process was endothermic, and the adsorption mechanism of CTAB onto GO was proven to be controlled by surface complexation, hydrogen bonding, and electrostatic attraction.     

氧化石墨烯量子点对鸡卵清蛋白递送-免疫增强佐剂效力评估

利用改进的Hummers法氧化鳞片石墨,获得富含羟基和羧基的氧化石墨烯量子点(GOQDs)。通过透射电子显微镜、X射线衍射、红外光谱及拉曼光谱测试表征其理化性质。此外,利用鸡卵清蛋白(OVA)作为模式抗原,构筑GOQDs/OVA纳米疫苗并评估其载量、安全性、免疫效力等。结果显示,GOQDs/OVA纳米疫苗直径在5nm左右,具有高度的水分散性和稳定性。其对OVA的最大负载量约为 500mg·g^-1,在pH=5.5和7.4环境下24 h的释放率分别为74.65%和56.93%,表现出pH刺激响应释放性能。当GOQDs浓度在500μg·mL^-1以下时,不会引起溶血、细胞损伤、重要组织发生病变等现象。免疫后,与 OVA单独免疫对照组相比,GOQDs/OVA纳米疫苗可以诱导产生高水平的免疫球蛋白G(IgG)、免疫球蛋白G1(IgG1)及免疫球蛋白G2a(IgG2a)抗体,提高白细胞介素(IL)-1β、IL-2、IL-4和IL-6、肿瘤坏死因子-α(TNF-α)和γ干扰素(IFN-γ)的分泌,同时促进脾中辅助性(CD4⁺)和细胞毒性(CD8⁺)T淋巴细胞百分比的增加。     

氧化石墨烯和石墨烯在催化领域中的应用研究进展

石墨烯具有独特的二维平面结构,其导电性能好,比表面积大,耐酸碱,耐高温.基于石墨烯的优异特性,本文作者从材料的合成和结构等方面对石墨烯基催化剂的研制及其催化性能进行了评述.介绍了石墨烯催化体系的类型和机理,对石墨烯催化中存在的问题进行了简单分析,并对石墨烯在催化领域的应用前景进行了展望.     

氧化石墨烯量子点对鸡卵清蛋白递送-免疫增强佐剂效力评估

利用改进的Hummers法氧化鳞片石墨,获得富含羟基和羧基的氧化石墨烯量子点(GOQDs)。通过透射电子显微镜、X射线衍射、红外光谱及拉曼光谱测试表征其理化性质。此外,利用鸡卵清蛋白(OVA)作为模式抗原,构筑GOQDs/OVA纳米疫苗并评估其载量、安全性、免疫效力等。结果显示,GOQDs/OVA纳米疫苗直径在5 nm左右,具有高度的水分散性和稳定性。其对OVA的最大负载量约为500 mg·g^-1,在pH=5.5和7.4环境下24 h的释放率分别为74.65%和56.93%,表现出pH刺激响应释放性能。当GOQDs浓度在500 μg·mL^-1以下时,不会引起溶血、细胞损伤、重要组织发生病变等现象。免疫后,与OVA单独免疫对照组相比,GOQDs/OVA纳米疫苗可以诱导产生高水平的免疫球蛋白G(IgG)、免疫球蛋白G1(IgG1)及免疫球蛋白G2a(IgG2a)抗体,提高白细胞介素(IL)-1β、IL-2、IL-4和IL-6、肿瘤坏死因子-α(TNF-α)和γ干扰素(IFN-γ)的分泌,同时促进脾中辅助性(CD4⁺)和细胞毒性(CD8⁺)T淋巴细胞百分比的增加。     

Novel graphene oxide/bentonite composite for uranium(VI) adsorption from aqueous solution

A novel graphene oxide/bentonite composite (GO/bentonite) was synthesized and then characterized through powder X-ray diffraction, fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and energy dispersive spectroscopy. Adsorption achieved equilibrium within 10 min. Moreover, U(VI) adsorption on GO/bentonite was highly dependent on solution pH and independent of ionic strength. These characteristics suggested that inner-sphere surface complexes of U(VI) formed on GO/bentonite. The adsorption of U(VI) from aqueous solution on GO/bentonite was fitted to the pseudo-second-order and Freundlich isotherm models. The maximum sorption capacity of GO/bentonite was 234.19 mg g^?1 under neutral pH at 303 K. GO/bentonite is a potentially powerful adsorbent for the efficient removal of U(VI) from aqueous solutions.     

Nickel sulphide-reduced graphene oxide composites as counter electrode for dye-sensitized solar cells: Influence of nickel chloride concentration

Nickel sulphide-reduced graphene oxide (NiS-rGO) composite films have been prepared via modified Hummers’s method assisted with spin coating technique. The NiS-rGO samples were then employed as counter electrode in a dye-sensitized solar cell (DSSC). The main aim of this work is to investigate the relationship between the concentrations of NiCl₂ with the properties of NiS-rGO and performance parameters of the device. The dominant rGO and minor NiS phase exist in the composite. The morphology of the composite is white strips rGO and NiS agglomerate particle. The element of C, O, Ni and S present in the composite. The highest η of 1.04% and J_sc of 7.39 mA cm⁻² were obtained from the device with 0.06 M NiCl₂ resulted from the longest carrier lifetime. The photovoltaic parameters results reveal that NiS-rGO composite has potential to become as a free platinum counter electrode of DSSC.