Irradiation effects on copper

Copper, one of the most significant metals, is exposed to IR radiation. A Nd:YAG laser (1064 nm, 1.1 MW, 12 ns) has been used to irradiate fine polished and annealed samples (4 N, 1×1×0.3 cm³) with 100 laser shots under a vacuum of ～10^?6 torr. The laser focal spot size and power density on the target were 12 μm and 3×10¹² Wm^?2 respectively. The surface and structural studies were performed by analyzing scanning electron micrographs and X-ray diffractograms (XRDs), respectively. Laser ablation results in boiling, splashing, hydrodynamical sputtering and exfoliation along with other relevant phenomena. The XRD patterns of the exposed sample indicate a change in diffraction intensity and grain sizes. The atomic planes remain undisturbed for the irradiated target. The information collected is useful for investigating the complexities found in radiation–metal interactions.     

Frequency stabilization of a diode laser using electromagnetically induced transparency in a V-configuration cesium atom

An electromagnetically induced transparency (EIT) signal is observed in a V-type energy level scheme in a cesium vapor cell at room temperature. The effects of frequency detuning and the intensity of the pump laser on the EIT signal have been investigated. The performance of the probe-diode laser system, which is frequency stabilized on the EIT signal by using electrical feedback, is explored. The first derivative of the EIT signal offers a steeper slope and better S/N ratio for laser frequency stabilization than that of the Doppler-free hyperfine and crossover resonances. A comparative study of the frequency stability of an external-cavity diode laser stabilized at EIT and at the crossover resonance is presented. The square root of the Allan variance (σ) vs. integration time (τ) plot shows about a tenfold improvement in the frequency stability of the EIT-locked laser (σ ～ 2.043 × 10^?13τ^?1/2) over that of the crossover-locked laser under a short integration time (1–10 ms), whereas a twofold improvement is found under a long integration time (～1 s).     

Tribological characterization of TiCN coatings deposited by two crossed laser ablation plasma beams

The simultaneous laser ablation of two targets (graphite and titanium) in an Ar-N₂ gas mixture was carried out to deposit thin films of the ternary compound TiCN at room temperature. The base conditions used to produce the TiN without carbon were taken from our previous studies. The experimental conditions for the ablation of the carbon target were varied so that the carbon content in the films could be changed depending on the carbon ion energy. The control of the experimental conditions was carried out using a Langmuir planar probe which permitted the determination of the mean kinetic ion energy. The maximum hardness value of 35 GPa, was obtained with a carbon ion energy of about 250 eV, which corresponds to a film with 5 at% carbon content. In order to perform tribological and scratch tests, two types of substrate were used: nitrided AISI 316 stainless steel and AISI 316 stainless steel previously coated with a thin titanium layer (～50 nm). Values of the wear rate in the range of 1.39×10^?6 to 7.45×10^?5 mm³?N^?1?m^?1, friction coefficient from 0.21 to 0.28 and adhesion from scratch test measurements up to 80 N for final critical load, were obtained.     

Experimental study of conditions for the 3D laser cladding of nickel aluminide

The layerwise laser cladding of powdered alloy based on intermetallic gamma Ni₃Al phase is studied. The effect deposition parameters have on the geometry of the deposited beads is shown. Microstructures are investigated and the cracking susceptibility of the deposited material is analyzed. The effective deposition parameters are determined within a range of specific laser energy inputs of (2–8) × 10⁶ J kg^?1 at beam scanning rates of (1.67–10) × 10^?3 m/s and a powder feed of 6.3 × 10^?5 kg/s^?1.     

Effect of N5+ ion irradiation on l-ornithine monohydrochloride single crystals: an organic nonlinear optical material

In this work, the authors have grown good-quality single crystals of l-ornithine monohydrochloride (LOHCL), an organic nonlinear optical material, in the aqueous solution by the slow cooling technique. N⁵⁺ ion irradiation of three different doses (i.e. 1?×?10¹⁶, 5?×?10¹⁶ and 1?×?10¹⁷?ions/cm²) at room temperature was done on the cut and polished crystal specimen of appropriate size from the grown crystal. A detailed study of FT-Raman spectroscopic was carried out to see the effect of irradiation on structure and vibrational modes of the LOHCL crystal. The results revealed that there is no structural modification even at high doses except the variation in peak intensity, which indicates that the grown crystals of LOHCL have good stability and also confirms that the nitrogen ions do not substitute into the crystal lattice. The UV–Vis–near-infrared spectroscopic study was done on all the samples to see the effect of irradiation and various optical parameters such as transmittance (～50–70%), absorption coefficient, energy band gap (～4.75–4.96?eV), extinction coefficient, refractive index (～1.31–1.24), optical permittivity (～1.7–1.6) and susceptibility (～0.7–0.6). The calculated optical parameters were found to vary with change in doses.     

Biocompatible film deposition by using Nd:YAG pulsed laser

A Nd:YAG laser operating at the fundamental wavelength (1064 nm) and at the second harmonic (532 nm), with 9 ns pulse duration, 100–900 mJ pulse energy, and 30 Hz repetition rate mode, was employed to ablate in vacuum (10^?6 mbar) biomaterial targets and to deposit thin films on substrate backings. Titanium target was ablated at the fundamental frequency and deposited on near-Si substrates. The ablation yield increases with the laser fluence and at 40 J/cm ² the ablation yield for titanium is 1.2×10¹⁶ atoms/pulse. Thin film of titanium was deposited on silicon substrates placed at different distance and angles with respect to the target and analysed with different surface techniques (optical microscopy, scanning electron spectrosopy (SEM), and surface profile).

Hydroxyapatite (HA) target was ablated to the second harmonic and thin films were deposited on Ti and Si substrates. The ablation yield at a laser fluence of 10 J/cm ² is about 5×10¹⁴ HA molecules/pulse. Thin film of HA, deposited on silicon substrates placed at different distance and angles with respect to the target, was analysed with different surface techniques (optical microscopy, SEM, and Raman spectroscopy).

Metallic films show high uniformity and absence of grains, whereas the bio-ceramic film shows a large grain size distribution. Both films found special application in the field of biomaterial coverage.     

Correlation of plume dynamics and oxygen pressure with VO2 stoichiometry during pulsed laser deposition

Vanadium dioxide thin films have been deposited on Corning glass substrates by a KrF laser ablation of V₂O₅ target at the laser fluence of 2 J?cm^?2. The substrate temperature and the target-substrate distance were set to 500 ^°C and 4 cm, respectively. X-ray diffraction analysis showed that pure VO₂ is only obtained at an oxygen pressure range of 4×10^?3–2×10^?2 mbar. A higher optical switching contrast was obtained for the VO₂ films deposited at 4×10^?3–10^?2 mbar. The films properties were correlated to the plume-oxygen gas interaction monitored by fast imaging of the plume.     

Extended homogeneous nanoripple formation during interaction of high-intensity few-cycle pulses with a moving silicon wafer

We report the study of extended nanoripple structures formed during the interaction of high-intensity 3.5 fs pulses with a moving silicon wafer. The optimization of laser intensity (8×10¹³ W?cm^?2) and sample moving velocity (1 mm?s^?1) allowed the formation of long strips (～5 mm) of homogeneous nanoripples along the whole area of laser ablation. The comparison of nanoripples produced on the silicon surfaces by few- and multi-cycle pulses is presented. We find that few-cycle pulses produce sharp and more homogenous structures than multi-cycle pulses.     

Detection of C2H2 and HCl using mid-infrared degenerate four-wave mixing with stable beam alignment: towards practical in situ sensing of trace molecular species

A stable and convenient optical system to realize the forward phase-matching geometry for degenerate four-wave mixing (DFWM) is demonstrated in the mid-infrared spectral region by measuring DFWM signals generated in acetylene (C₂H₂) and hydrogen chloride (HCl) molecules by probing the fundamental ro-vibrational transitions. IR laser pulses tunable from 2900 cm^?1 to 3350 cm^?1 with a 0.025 cm^?1 linewidth were obtained using a laser system composed of an injection seeded Nd:YAG laser, a dye laser, and a frequency mixing unit. At room temperature and atmospheric pressure, a detection limit of 35 ppm (～ 9.5×10¹⁴ molecules/cm³) for C₂H₂ was achieved in a gas flow of a C₂H₂/N₂ mixture by scanning the P(11) line of the (010(11)⁰)–(0000⁰0⁰) band. The detection limit of the HCl molecule was measured to be 25 ppm (～6.8×10¹⁴ molecules/cm³) in the same environment by probing the R(4) line. The dependences of signal intensities on molecular concentrations and laser pulse energies were demonstrated using C₂H₂ as the target species. The variations of the signal line shapes with changes in the buffer gas pressures and laser intensities were recorded and analyzed. The experimental setup demonstrated in this work facilitates the practical implementation of in situ, sensitive molecular species sensing with species-specific, spatial and temporal resolution in the spectral region of 2.7–3.3 μm (3000–3700 in cm^?1), where various molecular species important in combustion have absorption bands.     

Optical properties of Yb3+ ions in fluorophosphate glasses for 1.0 μm solid-state infrared lasers

Yb³⁺-doped fluorophosphate glasses were prepared by melt-quenching technique and characterized their spectroscopic properties to assess the laser performance parameters. The magnitude of absorption (emission) cross-sections at 975 nm for all the studied Yb³⁺-doped glasses is found to be in the range of 0.29–1.50 × 10^?20 (0.59–1.99 × 10^?20 cm²) which is much higher than those of commercial Kigre QX/Yb: 1.06 × 10^?20 (0.5 × 10^?20 cm²) laser glass. The luminescence lifetimes of ²F_5/2 level decrease (1.15–0.45 ms) with increase in Yb₂O₃ concentration (0.1–4.0 mol%). Effect of OH^? content on luminescence properties of Yb³⁺ ions has also been investigated. The effect of radiative trapping has been discussed by using McCumber (McC) and Fuchtbauer–Ladenburge (F–L) methods. The product of experimental lifetimes and emission cross-sections for 0.1 mol% Yb₂O₃-doped glass is found to be 2.28 × 10^?20 cm² ms which indicates that the higher energy storage and extraction capability could be possible. The detailed spectroscopic results suggest that the studied glasses can be considered for high-power and ultrashort pulse laser applications.     

Laser ablation of silver in different liquids: Optical and nonlinear optical properties of silver nanoparticles

The optical, structural, and nonlinear optical properties of silver nanoparticles prepared using the method of laser ablation in various liquids at wavelengths of 397, 532, and 795 nm with laser pulses of different duration are studied. An analysis of the dimensional and spectral characteristics of the silver nanoparticles revealed a time dynamics of the nanoparticle size distribution in solutions. It is shown that thermal self-defocusing is observed for the case of nanosecond or shorter pulses generated with a high repetition rate. For picosecond and femtosecond pulses with a low repetition rate, the effects of self-focusing (γ = 3 × 10^?13 cm² W^?1) and saturated absorption (β = ?1.5 × 10^?9 cm W^?1) were observed in the solutions under study. The third-order nonlinear susceptibility of the silver nanoparticles was found to be 5 × 10^?8 esu at a wavelength of 397 nm.     

Surface modification and adhesion of wood-plastic composite (WPC) treated with UV/ozone

Because of the surfaces of wood-plastic composite (WPC) materials are enriched in polymers of low surface energy, they exhibit low adhesion properties. UV/ozone is proposed as surface treatment for increasing the surface energy and adhesion of WPC materials made with different polymers (polyethylene, polypropylene and polyvinyl chloride). UV lamp-WPC surface distance and time of UV exposure were varied for optimizing UV/ozone treatment of WPC, and UV dose used ranged between 2.02 × 10^?14 and 5.05 × 10^?12 J·s/m². UV/ozone treatment created new carbon-oxygen polar groups in WPC surfaces and increased their surface energy, mainly their polar component. Furthermore, ablation of the outermost WPC surface was produced, more noticeably by reducing the distance between WPC surface and UV lamp and by increasing the duration of the treatment. Noticeable increase in 180° peel adhesion was obtained in the joints made with UV/ozone treated WPC at 10–30 mm distance during 1–5 min (i.e., UV dose between 5.61 × 10^?14 and 2.53 × 10^?12 J·s/m²). Although 180° peel strength of joints made with acrylic adhesive tape and UV/ozone treated WPC for 10 min and 10 mm distance (UV dose: 5.05 × 10^?12 J·s/m²) was not increased because of dominant effect of ablation over creation of polar groups, the cross-hatch adhesion to different coatings was highly improved, irrespective of the polymer used and the wood content of WPC; however, the surface modifications and adhesion of UV/ozone treated WPC were more marked when its wood content was higher and by using UV dose between 0.10 × 10^?12 and 2.53 × 10^?12 J·s/m².     

Studies of some physical properties of PrFe0.7Ni0.3O3 thin films after 200 MeV Ag15+ irradiation

PrFe_0.7Ni_0.3O₃ thin films (thickness ~ 200 nm) were prepared by pulsed laser ablation technique on LaAlO₃ substrate. These films were irradiated with 200?MeV Ag¹⁵⁺ ions at various fluencies, ranging from 1 × 10¹¹ to 1 × 10¹² ions/cm². These irradiated thin films were characterized by using X-ray diffraction, dc conductivity, dc magnetization and atomic force microscopy. These films exhibit orthorhombic structure and retain it even after irradiations. The crystallite size (110–137?nm), micro strain (1.48 × 10^?2–1.75 × 10^?2 line^?2?m^?4) and dislocation density (79.7 × 10¹⁴–53.2 × 10¹⁴ line/m²) vary with ion fluencies. An enhancement in resistivity at certain fluence and then a decrease in its value (0.22175–0.21813?Ω?cm) are seen. A drastic change in observed magnetism after ion irradiation is seen. With ion irradiation, an increase in surface roughness, due to the formation of hillocks and other factors, is observed. Destruction of magnetic domains after irradiation can also be visualized with magnetic force microscopy and is in close agreement with magnetization data. The impact on various physical properties in these thin films after irradiation indicates a distortion in the lattice structure and consequently on single-particle band width caused by stress-induced defects.     

Photo-emission studies from Zn cathodes under plasma phase

In this paper, we report investigations of the electron emission from pure Zn cathodes irradiated by UV laser pulses of 23 ns (full-width at half-maximum) at a wavelength of 248 nm (5 eV). The metal cathodes were tested in a vacuum photodiode chamber at 10^?5 Pa. They were irradiated at normal incidence and the anode–cathode distance was set at 3 mm. The maximum applied accelerating voltage was 18 kV, limited by the electrical breakdown of the photodiode gap. Under the above experimental conditions, a maximum applied electric field of 6 MV/m resulted. In the saturation regime, the measured quantum efficiency value increased with the accelerating voltage due to the plasma formation. The highest output current was achieved with 14 mJ laser energy, 18 kV accelerating voltage and its value was 12 A, corresponding to a global quantum efficiency (GQE) approximately of 1×10^?4. The temporal quantum efficiency was 1.0×10^?4 at the laser pulse onset time and 1.4×10^?4 at the pulse tail. We calculated the target temperature at the maximum laser energy. Its value allowed us to obtain output pulses of the same laser temporal profile. Tests performed with a lower laser photon energy (4.02 eV) demonstrated a GQE of two orders of magnitude lower.     

Protective films of diamond for high Tc superconducting detectors

Deposition of diamond like carbon (DLC) films on YBCO superconducting detectors is reported. The method is to make a DLC film by C⁺ implantation and XeCl excimer laser irradiation. The implantation energy is 20–35 keV and C⁺ implantation dosages D=1×10¹⁴–5×10¹⁸ ions/cm². The parameters of XeCl excimer laser ablation are: wavelength, 308 nm; energy density, 20–50 mJ/cm²; and width of pulse, 45 ns. The superconductivity of C⁺-implanted YBCO is also investigated, while the damage behavior of C⁺ implantation and the mechanism of coating DLC are analyzed.     

Irradiation effects of 12 eV oxygen ions on polyimide and fluorinated ethylene propylene

Polyimide (PI) and Fluorinated Ethylene Propylene (FEP) samples (15 mm×15 mm×50 μm ) were exposed to atomic oxygen ions of average energy ～12 eV and flux ～5×10¹³ ions cm ^?2 s ^?1, produced in the Electron Cyclotron Resonance (ECR) plasma. The energy and the flux of the oxygen ions at different positions in the plasma were measured by a retarding field analyzer. The fluence of the oxygen ions was varied from sample to sample in the range of ～5×10¹⁶ to 2×10¹⁷ ions cm ^?2 by changing the irradiation period. The pre- and the post-irradiated samples were characterized by the weight loss, Scanning Electron Microscopy (SEM), X-ray Photoelectron Spectroscopy (XPS), and Fourier Transform Infrared (FTIR) techniques. The weight of the PI and FEP samples decreased with increasing the ion fluence. However, the erosion yield for the PI is found to be higher, by almost a factor five, when compared with that of FEP. On the surface region of irradiated samples, the concentrations of the carbon, fluorine, and oxygen and their corresponding chemical bonds have changed appreciably. Moreover, blisters and nanoglobules were also observed even at a fluence of ～10¹⁷ ions cm ^?2. This oxygen ion fluence is almost two orders of magnitude lower than that of the 5 eV atomic oxygen, which a satellite encounters in the space, at the low Earth orbit, during its mission period of about 7 years.     

Formation of laser jet thrust in the supersonic regime

Basic methods for obtaining laser jet thrust in the supersonic regime corresponding to the supersonic flow in the jet nozzle are analyzed. It is shown that the method based on the interaction of a laser ablative jet with the supersonic flow is promising. In this case, laser thrust is formed due to additional acceleration of the flow behind the ablation region. Numerical simulation of the flow in a parabolic nozzle is employed to demonstrate the possibility of effective formation of laser thrust at a level of 3 × 10^?3 N/W.     

The GaP(001) surface and the adsorption of Cs

GaP(001) cleaned by argon-ion bombardment and annealed at 500°C showed the Ga-stabilized GaP(001)(4 × 2) structure. Only treatment in 10^?5 Torr PH₃ at 500°C gave the P-stabilized GaP(001)(1 × 2) structure. The AES peak ratio $\text{P}\text{Ga}$ is 2 for the (4 × 2) and 3.5 for the (1 × 2) structure. Cs adsorbs with a sticking probability of unity up to 5 × 10¹⁴ Cs atoms cm^?2 and a lower one at higher coverages. The photoemission measured with uv light of 3660 Å showed a maximum at the coverage of 5 × 10¹⁴ atoms cm^?2. Cs adsorbs amorphously at room temperature, but heat treatment gives ordered structures, which are thought to be reconstructed GaP(001) structures induced by Cs. The LEED patterns showed the GaP(001)(1 × 2) Cs structure formed at 180°C for 10 h with a Cs coverage of 5 × 10¹⁴ atoms cm^?2, the GaP(001)(1 × 4) Cs formed at 210°C for 10 hours with a Cs coverage of 2.7 × 10¹⁴ atoms cm^?2, the GaP(001)(7 × 1) and the high temperature GaP(001)(1 × 4), the latter two with very low Cs content. Desorption measurements show three stability regions: (a) between 25–150°C for coverages greater than 5 × 10¹⁴ atoms cm^?2, and an activation energy of 1.2 eV; (b) between 180–200°C with a coverage of 5 × 10¹⁴ atoms cm^?2, and an activation energy of 1.8 eV; (c) between 210–400°C with a coverage of 2.7 × 10¹⁴ atoms cm^?2, and an activation energy of 2.5 eV.     

Identification of non-thermal and thermal processes in femtosecond laser-ablated aluminum

Non-thermal and thermal processes due to femtosecond laser ablation of aluminum (Al) at low, moderate, and high-fluence regimes are identified by Atomic Force Microscope (AFM) surface topography investigations. For this purpose, surface modifications of Al by employing 25 fs Ti: sapphire laser pulses at the central wavelength of 800 nm have been performed to explore different nano- and microscale features such as hillocks, bumps, pores, and craters. The mechanism for the formation of these diverse kinds of structures is discussed in the scenario of three ablation regimes. Ultrafast electronic and non-thermal processes are dominant in the lower fluence regime, whereas slow thermal processes are dominant at the higher fluence regime. Therefore, by starting from the ablation threshold three different fluence regimes have been chosen: a lower fluence regime (0.06–0.5 J cm^?2 single-shot irradiation under ultrahigh vacuum condition and 0.25–2.5 J cm^?2 single-shot irradiation in ambient condition), a moderate-fluence regime (0.25–1.5 J cm^?2 multiple-shot irradiation), and a high-fluence regime 2.5–3.5 J cm^?2 multiple-shot irradiation. For the lower fluence (gentle ablation) regime, around the ablation threshold, the unique appearance of individual, localized Nano hillocks typically a few nanometers in height and less than 100 nm in diameter are identified. These Nano hillock-like features can be regarded as a nonthermal, electronically induced phase transition process due to localized energy deposition as a result of Coulomb explosion or field ion emission by surface optical rectification. At a moderate-fluence regime, slightly higher than ablation threshold multiple-pulse irradiation produces bump-formation and is attributed to ultrafast melting (plasma formation). The high-fluence regime results in greater rates of material removal with highly disturbed and chaotic surface of Al with an appearance of larger protrusions at laser fluence well above the ablation threshold. These nonsymmetrical shapes due to inhomogeneous nucleation, cluster formation, and resolidification of a metallic surface after melting are attributable to slow thermal processes (ps time scale).     

Electrical and optical properties of ITO and ITO/Cr-doped ITO films

In this paper we report on the effects of the insertion of Cr atoms on the electrical and optical properties of indium tin oxide (ITO) films to be used as electrodes in spin-polarized light-emitting devices. ITO films and ITO(80 nm)/Cr-doped ITO(20 nm) bilayers and Cr-doped ITO films with a thickness of 20 nm were grown by pulsed ArF excimer laser deposition. The optical, structural, morphological and electrical properties of ITO films and ITO/Cr-doped structures were characterized by UV–Visible transmission and reflection spectroscopy, transmission electron microscopy (TEM), atomic force microscopy (AFM) and Hall-effect analysis. For the different investigations, the samples were deposited on different substrates like silica and carbon coated Cu grids. ITO films with a thickness of 100 nm, a resistivity as low as ～4×10^?4 Ω?cm, an energy gap of ～4.3 eV and an atomic scale roughness were deposited at room temperature without any post-deposition process. The insertion of Cr into the ITO matrix in the upper 20 nm of the ITO matrix induced variations in the physical properties of the structure like an increase of average roughness (～0.4–0.5 nm) and resistivity (up to ～8×10^?4 Ω?cm). These variations were correlated to the microstructure of the Cr-doped ITO films with particular attention to the upper 20 nm.