温度与pH快速响应性P(NIPAM-co-AAc)水凝胶的制备及其性能

以氯化钠水溶液作为反应介质,成功制备了温度与pH快速响应性聚(N-异丙基丙烯酰胺-co-丙烯酸)[P(NIPAM-co-AAc)]水凝胶,研究了氯化钠水溶液的浓度对凝胶性能的影响.通过红外光谱(FT-IR)、扫描电镜(SEM)、测溶胀比对凝胶性能进行了表征.结果表明:凝胶具有相同的化学组成与结构,但具有不同的微观形态;随着反应介质中氯化钠浓度的增加,凝胶在20℃蒸馏水中的平衡溶胀比增大,并表现出较强的温度与pH敏感性以及较快的去溶胀速率.     

聚丙烯酰胺纳米复合水凝胶研究进展

传统化学交联的聚丙烯酰胺(PAM)水凝胶由于力学性能较弱,其应用范围受到很大限制。与之相比,采用纳米复合技术制备的PAM纳米复合(NC)水凝胶,不仅大幅提高了力学性能,而且在溶胀率等方面也有明显的提高。本文结合该领域近年来的研究进展,将PAM NC水凝胶分为纯物理交联和化学物理交联相结合两类,重点讨论了NC水凝胶在力学性能方面的研究结果,对溶胀率等其它方面的性能也进行了综合论述。     

多孔聚N-异丙基丙烯酰胺水凝胶的制备与缓释性能

以N-异丙基丙烯酰胺(NIPA)、N,N-亚甲基双丙烯酰胺(MBA)和聚乙二醇(PEG)为原料,以60Co-γ射线为放射源制备了快速响应聚N-异丙基丙烯酰胺(PNIPA)多孔水凝胶。用红外光谱分析了水凝胶的结构,并测定了水凝胶的溶胀动力学、退溶胀动力学和平衡溶胀率。结果表明,PEG分子仅在聚合交联过程中充当成孔剂,不参与反应,反应后可被除去;水凝胶具有明显的温度敏感性,成孔剂的添加提高了水凝胶的溶胀性能和LCST。选用阿司匹林为模型药物,对水凝胶的药物缓释性能进行了初步研究。     

聚乙烯醇/羧甲基壳聚糖共混水凝胶的辐射合成及性能

采用电子加速器辐照法制备了聚乙烯醇(PVA)/羧甲基壳聚糖(CMCH)共混水凝胶;研究了PVA与CMCH的配比、辐照剂量、温度以及pH值对PVA/CMCH共混水凝胶性能的影响.实验发现,PVA与CMCH在辐照剂量为40 kGy、配比为w(PVA)/w(CMCH)=5/1的条件下可得到强度较好的PVA/CMCH共混水凝胶,该水凝胶具有一定的温度和pH敏感性:在5~20℃时具有较高的溶胀率,温度在20℃以上溶胀率较低;水凝胶在pH<4.0和pH>6.0时溶胀率均较大,而当pH为4.0~6.0时溶胀率较小.     

辐射交联制备改性CMC水凝胶的溶胀行为研究

利用丙烯酰胺 (AAm)接枝改性纤维素 ,然后进行羧甲基化反应得到高取代度的丙烯酰胺 羧甲基纤维素钠 (AAm CMC Na) .对该材料进行γ射线辐照制备出新型改性CMC水凝胶 .研究了这种水凝胶的溶胀动力学、交联动力学以及温度、pH值和无机盐浓度对水凝胶溶胀行为的影响 ,并与CMC Na水凝胶进行了比较 .结果表明 ,该水凝胶和CMC Na水凝胶相比 ,优点在于辐照交联所用的剂量下降 ,而且所需的CMC浓度减少 .AAm CMC Na水凝胶的溶胀度随温度升高而增大 ,在pH为 6～ 8范围内达到最大值 ,并随无机盐浓度与吸收剂量增加而下降 ,表现出较好的温度敏感性和pH敏感性 ,可望作为吸水材料和水保持剂     

纤维素纳米纤维接枝聚(N-异丙基丙烯酰胺)水凝胶的制备与表征

将具有温度响应的聚N-异丙基丙烯酰胺(PNIPAm)接枝到电纺纤维素纳米纤维膜上,制备温度响应型纤维素接枝聚N-异丙基丙烯酰胺(PNIPAm-g-Cell)纳米纤维水凝胶。 研究接枝单体(N)与纤维素(c)的质量比、反应温度、反应时间和引发剂浓度对产物接枝率、溶胀性和形貌的影响。 结果表明,最佳聚合反应条件为m(N):m(c)=15:1、反应温度40 ℃、反应时间3 h、引发剂浓度为10 mmol/L,得到PNIPAm-g-Cell接枝率和溶胀率分别为35%和31%。 与PNIPAm相比,PNIPAm-g-Cell水凝胶的低临界相转变温度(LCST)显著升高,说明亲水性纤维素的引入改变了体系的亲疏水平衡。 去溶胀动力学测试表明,0.5 min内接枝率为25%和35%的水凝胶保水率分别降低至93%和61%。 说明接枝率越高PNIPAm-g-Cell水凝胶对温度的响应速度越快,对温度越敏感。     

通过麦克加成反应形成的三臂聚乙二醇丙烯酸酯可注射水凝胶的制备与表征

通过麦克加成反应在磷酸盐缓冲溶液中制备出一种基于三臂聚乙二醇丙烯酸酯的能快速固化的可注射水凝胶.采用倒置法测定了体系的凝胶化时间.通过红外,DMA,溶胀,降解等一系列测试,研究了该水凝胶的结构和物理化学性能.观察到通过控制前体溶液的浓度,可以控制凝胶的成胶时间和所形成凝胶的溶涨率.同时表明该水凝胶具备可注射性和可降解性.细胞毒性评价显示,该水凝胶浸提液无毒性,符合生物材料的安全评价标准.由于麦克加成反应可在人体生理条件(pH7.4,37℃)下快速进行,并且不需要任何引发剂、催化剂和有机溶剂,因此该反应非常适合应用于生物医用材料领域.     

新型半纤维素基磁性水凝胶的制备及性能

采用H2O2-Vc氧化还原体系引发半纤维素衍生物,以表面修饰的Fe3O4粒子作为磁性组分,利用接枝共聚方法制备了新型半纤维素基磁性水凝胶.分别用傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)和扫描电子显微镜(SEM)对水凝胶的结构及形貌进行了表征,利用X射线衍射(XRD)和振动样品磁强计(VSM)对水凝胶的晶型结构及磁性能进行了分析,发现Fe3O4粒子均匀分散在凝胶网络中,半纤维素基磁性水凝胶表现出良好的顺磁性.考察了丙烯酸/半纤维素比例、Fe3O4粒子含量及交联剂用量对水凝胶溶胀性能的影响,并探讨了该水凝胶的溶胀机理,它在pH 8缓冲溶液中的溶胀较好符合Fickian和Schott动力学模型.通过SEM和溶胀性能分析表明,随着pH值的升高水凝胶的孔径增大,水凝胶的溶胀率逐渐增大.制备的水凝胶被用于溶菌酶吸附研究,结果表明磁性凝胶的吸附量大于非磁性水凝胶,水凝胶的吸附行为符合Freundlich和Temkin等温模型.     

羧甲基纤维素-壳聚糖水凝胶球的制备及性能

采用物理交联法制备了羧甲基纤维素(CMC)-壳聚糖(CS)共混水凝胶球;研究了共混球的耐酸碱性、溶胀性及对亚甲基蓝的吸附性能.结果表明,水凝胶球在弱酸和弱碱中具有一定的稳定性;随着羧甲基纤维素与壳聚糖质量比的增大,水凝胶的吸水溶胀率增加.在CMC与CS质量比为1∶4时制备的水凝胶呈规则球状.     

麦饭石含量对载药复合凝胶小球释药性能的影响

以瓜尔胶-g-聚丙烯酸/麦饭石复合水凝胶(GG-g-PAA/MS)和海藻酸钠(SA)为原料,双氯芬酸钠(DS)为模拟药物,采用离子凝胶法制备了载药复合凝胶小球,考察了pH敏感性以及MS含量对复合凝胶小球的包封率、载药率、溶胀性和药物释放行为的影响.结果表明:凝胶小球具有明显的pH敏感性,在不同pH介质中溶胀率和释放速率...     

Design and preparation of pH-responsive curdlan hydrogels as a novel protein delivery vector

New pH-responsive saccharide hydrogels were designed and prepared using curdlan derivatives(curdlan-Bochistidine, CUR-HIS). The CUR-HIS hydrogels possessed highly porous structures. The swelling ratios of CUR-HIS hydrogels increased with the degree of substitution of Boc-histidine groups. And the addition of 0.5 mol/L Na Cl provoked a sharp reduction of swelling ratio of CUR-HIS hydrogels. Bovine serum albumin(BSA) can be efficiently encapsulated into CUR-HIS hydrogels. Moreover, the release profiles of BSA at different p H values from CUR-HIS hydrogels were significantly different. These hydrogels showed good biocompatibility in the cytotoxicity assays. The CUR-HIS hydrogels are of great potential in biomedical applications such as protein delivery systems.     

P(AMPS-co-BMA)水凝胶的电场敏感性及电刺激响应机理

以离子型单体2-丙烯酰胺-2-甲基丙磺酸(AMPS)及非离子型单体甲基丙烯酸丁酯为原料, 偶氮二异丁腈为引发剂, N,N′-亚甲基双丙烯酰胺为交联剂, N,N-二甲基甲酰胺为溶剂, 通过自由基聚合合成了一系列聚离子浓度不同的聚(2-丙烯酰胺-2-甲基丙磺酸-co-甲基丙烯酸丁酯)电场敏感性水凝胶. 研究了其在去离子水及NaCl溶液中的溶胀行为. 结果表明, 该水凝胶在去离子水中的平衡溶胀度在236.4~298.5之间, 其溶胀速率随着AMPS用量的增加而增加; 并且随着凝胶内部聚离子浓度的增加, 凝胶在NaCl溶液中的消溶胀速率及消溶胀度逐渐减小. 凝胶的电刺激响应性能研究结果表明, 在电场存在下, 凝胶在NaCl溶液中的溶胀行为与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 凝胶溶胀, 反之则凝胶消溶胀; 而且, 凝胶在电场作用下的偏转行为同样与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 偏向阴极, 反之则凝胶偏向阳极. 另外, 在电场存在下, 凝胶在NaCl溶液中的电偏转速度与环境温度密切相关.     

Swelling behavior of ionically cross-linked polyampholytic hydrogels in varied salt solutions

Ionically cross-linked polyampholytic hydrogels were synthesized by redox copolymerization of acrylamide and an ionic complex of (N,N-diethylamino)ethyl methacrylate and acrylic acid (designated as PADA hydrogel). The swelling behavior of the hydrogels in water indicated that a minimal equilibrium swelling ratio is found when the molar ratio of anionic/cationic monomers was 1.55. In NaCl solution, the hydrogels exhibited the typical swelling behavior of conventional polyampholytic gels. Their equilibrium swelling ratios increased with an increase in the NaCl concentration. In solutions of multivalent ions (CaCl₂ and trisodium citrate solutions), the equilibrium swelling ratios of the hydrogels increased first and were then followed by a decrease with an increase in salt concentration. Interestingly, an unexpected abrupt swelling phenomenon was observed when the fully swollen hydrogels in salt solution were transmitted to pure water. The unique swelling behavior of PADA hydrogels depends not only on the molar ratio of the anionic/cationic monomers but also on the valency of the ions.     

含甲基丙烯酸-N,N-二甲氨基乙酯水凝胶的紫外辐射合成及其性质研究

紫外光辐照 ,H2 O2 为光引发剂 ,N ,N′ 亚甲基双丙烯酰胺为交联剂合成了含甲基丙烯酸 N ,N 二甲氨基乙酯的水凝胶 .研究了水溶液中单体、光敏引发剂、交联剂浓度及光照时间对生成的水凝胶的凝胶含量和溶胀性能的影响 ,给出了最佳合成条件 .用该聚合法合成的聚甲基丙烯酸 N ,N 二甲氨基乙酯水凝胶不仅具有较好的透明性和适当的弹性 ,而且在 40℃和 pH =3时有明显的温度及 pH敏感性 .但离子强度对凝胶溶胀性能没有明显影响     

A study on the swelling behavior of poly(acrylic acid) hydrogels obtained by electron beam crosslinking

Poly(acrylic acid) (PAA) hydrogels were prepared by using electron beam (EB) crosslinking of PAA homopolymer from its aqueous solutions. The swelling behavior of the hydrogels was studied as a function of the concentration of PAA solution, radiation dose, pH of the swelling medium and swelling time. Also the environmental pH effect on the water diffusion mode into hydrogels was investigated. These hydrogels clearly showed pH-sensitive swelling behavior with Fickian type of diffusion in the stomach-like pH medium (pH 1.3) and non-Fickian type in the intestine-like pH medium (pH 6.8).     

PAMPS/SiO_2杂化水凝胶的合成及电场敏感性研究

以2-丙烯酰胺-2-甲基丙磺酸(AMPS)为有机原料,正硅酸乙酯(TEOS)为无机原料,过硫酸钾为引发剂,N,N'-亚甲基双丙烯酰胺为交联剂,通过原位-凝胶水溶液聚合法合成了一系列不同二氧化硅含量和不同聚离子浓度的聚(2-丙烯酰胺-2-甲基丙磺酸)/二氧化硅杂化电场敏感性水凝胶.通过扫描电子显微镜(SEM)表征凝胶的结构,研究水凝胶在去离子水以及氯化钠溶液中的溶胀和消溶胀行为.结果表明,系列凝胶的平衡溶胀度介于224.9至325.6之间,复合凝胶的溶胀速率随TEOS用量的增加而降低;除理想杂化凝胶外,随着聚离子浓度的升高,凝胶在氯化钠溶液中的消溶胀速率逐渐减小.对凝胶的电场敏感性研究表明,当聚离子浓度大于氯化钠溶液浓度时,凝胶进一步溶胀,反之则消溶胀,其中杂化凝胶的再溶胀性能减弱,而消溶胀行为变得更为明显.同时制得的理想杂化凝胶,较纯有机凝胶具有更为理想的力学性能,最大抗压缩强度可达23.4 MPa.     

The Influence of Preparation Methods on the Swelling and Network Properties of Acrylamide Hydrogels with Crosslinkers

Abstract

Using different types and concentrations of crosslinkers, acrylamide (AAm) hydrogels have been prepared with chemical initiation and gamma irradiation techniques. The effects of the preparation method, crosslinkers type and concentration on swelling behavior of AAm hydrogels were investigated. Swelling was performed in distilled water and followed gravimetrically. Swelling parameters such as equilibrium swelling degree, equilibrium water content (EWC), maximum swelling, initial swelling rate, diffusion exponent and coefficient, and network parameters such as molecular mass between crosslinks, crosslink density, mesh size, and porosity were calculated and evaluated. The range of equilibrium swelling degree of AAm hydrogels was varied from 255% to 1450% depending upon the preparation method, crosslinker type, and crosslinker concentration. The diffusion of water into AAm hydrogels was found to be nonFickian.     

TEMPERATURE AND pH RESPONSE, AND SWELLING BEHAVIOR OF POROUS ACRYLONITRILE-ACRYLIC ACID COPOLYMER HYDROGELS

Macroporous acrylonitrile-acrylic acid （AN-AA） copolymer hydrogels were synthesized by flee-radical solution polymerizations, using ammonium persulfate （APS）/N,N,N＇,N＇-tetramethylethylenediamine （TEMED） redox initiator system and alcohols porogens. The morphology, temperature and pH sensitive swelling behavior, and swelling kinetics of the resulting hydrogels were investigated. It was found that alcohol type and concentration had great influences on the pore structure and porosity of hydrogels. The pore size of hydrogel increases with the moderate increase of the length of alcohol alkyl chain. However, a further increase of alkyl length would result in the formation of cauliflower-like structure and the decrease of pore size. The porosity of hydrogels increases with the increase of porogen concentration in the polymerization medium. The hydrogels with macroporous structure swell or shrink much faster in response to the change of pH in comparison with the conventional hydrogel without macroporous structure. Furthermore, the response rate is closely related to the porosity of the hydrogels, which could be easily controlled by modulating the concentration of the porogen in the medium. The circular swelling behavior of hydrogels indicated the formation of a relaxing three-dimensional network.     

溶致液晶作模板水凝胶的制备及其表征

以表面活性剂Brij 58溶致液晶(LLC)为模板, 采用光聚合的方法合成了结构规整的新型溶致液晶型聚丙烯酰胺(PAAm)水凝胶, 并对其结构、形貌和性能进行了研究. 扫描电镜结果表明活性剂Brij 58用量为10%～40%时, 可形成结构规整、孔径均一的LLC型水凝胶, 其孔径为1～2 µm, 约为普通水凝胶的1/40. 当Brij 58浓度大于50%时, 体系发生相分离, 此时合成的水凝胶含水量及孔隙率下降. 傅立叶变换红外光谱(FTIR)显示, LLC型水凝胶中羰基和氨基的红外吸收向低波数方向移动, 表明其中形成了大量的分子间氢键. 同时, LLC型PAAm水凝胶还保持了普通水凝胶的pH敏感性, 相同条件下, 其溶胀比大于普通水凝胶.     

Synthesis and Characterization of Sterculia Gum Based pH Responsive Drug Delivery System for Use in Colon Cancer

The present study deals with the modification of sterculia gum to develop the novel colon specific delivery system for use in colon cancer. The sterculia and acrylic acid based hydrogels were synthesized and characterized with FTIR, SEMs, TGA and swelling behavior. Swelling studies of the hydrogels were carried out as a function of reaction parameters such as monomer concentration, initiator concentration, amount of sterculia gum and crosslinker concentration and nature of swelling mediums. Swelling kinetics of the hydrogels and in vitro release dynamics of anticancer model drug methotrexate from the hydrogels were studied to evaluate the swelling mechanism and drug release mechanism from the drug-loaded hydrogels. The values of diffusion exponent for the release of drug were 0.883, 0.910 and 0.787 in distilled water, pH 2.2 buffer and pH 7.4 buffer, respectively. The release of drug from the polymer matrix occurred through a non -Fickian type diffusion mechanism.