光时分复用(OTDM)系统中基于电吸收调制器(EAM)的短脉冲光源及解复用器的设计考虑

研究了电吸收调制器（ＥＡＭ） 的衰减随外加反向电压增加而指数增加的情形下,短脉冲光源的脉冲输出和解复用器的开关窗口对ＥＡＭ 的消光效率、反向ＤＣ 偏置电压以及正弦ＲＦ 驱动信号的幅度等参量的依赖关系－ 在基于ＥＡＭ 的短脉冲光源中,输出脉冲的消光比等于ＥＡＭ 消光效率η与正弦驱动电压峰峰值Ｖｐｐ 的乘积,输出光脉冲的消光比和脉宽均与ＥＡＭ 的反向偏置电压无关,但输出脉冲的峰值功率与η、Ｖｐｐ 和Ｖｂ 都有关系－ 在基于ＥＡＭ的解复用器中,为了使解复用器的开关窗口近似为矩形,可利用ＥＡＭ 的削波效应,使Ｖｐｐ／２＞ Ｖｂ－ 在ＥＡＭ 的消光效率η已知时,通过仔细设计反向ＤＣ 偏置电压Ｖｂ 和正弦驱动电压的峰峰值Ｖｐｐ ,达到ＯＴＤＭ 解复用器所需要的开关窗口形状、宽度和消光比－     

光时分复用(OTDM)系统中基于电吸收调制器(EAM)的短脉冲光源及解复用器的设计考虑

研究了电吸收调制器(EAM)的衰减随外加反向电压增加而指数增加的情形下,短脉冲光源的脉冲输出和解复用器的开关窗口对EAM的消光效率、反向DC偏置电压以及正弦RF驱动信号的幅度等参量的依赖关系.在基于EAM的短脉冲光源中,输出脉冲的消光比等于EAM消光效率η与正弦驱动电压峰峰值V_pp的乘积,输出光脉冲的消光比和脉宽均与EAM的反向偏置电压无关,但输出脉冲的峰值功率与η、V_pp和V_b都有关系.在基于EAM的解复用器中,为了使解复用器的开关窗口近似为矩形,可利用EAM的削波效应,使V_pp/2>V_b.在EAM的消光效率η已知时,通过仔细设计反向DC偏置电压V_b和正弦驱动电压的峰峰值V_pp,达到OTDM解复用器所需要的开关窗口形状、宽度和消光比.     

Performance Investigation of Photonic Crystal-Based Microring Resonator for Optical Signal Processing

Abstract

A detailed theoretical analysis is presented to characterize wave propagation at 1,550 nm inside a glass (SiO₂) microring resonator implemented using photonic crystal technology. A photonic crystal reflection is used at each microring resonator corner to enhance the bending efficiency. The characteristics of both photonic crystal beam splitter and microring resonator bending losses are analyzed and investigated using both effective refractive index and finite difference time domain methods. Analytical expressions are also derived to describe the field enhancement inside the microring resonator, the transfer function of the microring resonator, and the main parameters characterizing the resonator such as resonator band width and quality factor. The analysis is also extended to characterize a drop filter implemented using photonic crystal-based microring resonator. The results indicate clearly that the effective refractive index method can give accurate results if one starts the calculations with finite difference time domain-estimated beam splitter parameters. Further, bending efficiency as high as 99% can be obtained using a ten-post layer photonic crystal mirror at each microring resonator corner.     

输入光特性对超快非线性干涉仪开关窗口的影响

就超快非线性干涉仪(UNI)的输入光特性对其开关窗口的影响进行了数值模拟和实验研究,输入光包括控制光脉冲和探测光脉冲。在数值模拟中,调节控制光脉冲和探测光脉冲的功率及脉宽,功率越高和脉宽越窄,窗口的形状越好。在调节过程中发现控制光脉冲和探测光脉冲都存在一个最佳的功率点使窗口的形状达到最优。如果继续增大控制光脉冲功率,会使窗口的顶部倾斜,窗口形状恶化;而继续增大探测光脉冲功率,窗口的消光比开始下降。在数值模拟的基础上进行了10Gb／s的超快非线性干涉仪全光开关实验,在实验中用连续光代替探测光脉冲以观察窗口形状。通过改变控制光脉冲和连续光功率来验证它们对超快非线性干涉仪开关窗口的影响。实验表明,应选用短而强的控制光脉冲和最优功率点的连续光,这与模拟结果吻合。     

Quantum packet switching generation using correlated photons in a microring resonator system

We propose a new system of a packet of quantum bits generation using a soliton pulse within a microring resonator. A quantum gate can be formed by using a polarization control unit incorporating into the system. The random signal and idler pairs can be formed within the photon correlation bandwidth, which can be generated, and randomly form the packet quantum bits, i.e. quantum packet switching. Each random code (logic) can be performed by combining the signal and idler of each entangled photon pair via the quantum gate. Results obtained have shown that the packet of quantum logic bits can be generated using the entangled photon pairs generated by the proposed system.     

1×|N 信道聚合物微环谐振器电光开关阵列的开关特性

利用耦合模理论、电光调制理论和微环谐振理论,提出了一个完善合理的聚合物微环谐振器电光开关阵列模型.该器件由1条水平信道、N条竖直信道和N个微环构成,在微环上施加不同方式的驱动电压,可以实现N＋1条信道的开关功能.以1×8信道结构为例,在1 550 nm谐振波长下对该器件进行了优化设计和模拟分析.其结果是：微环波导芯的截面尺寸为1.7×1.7 μm2,波导芯与电极间的缓冲层厚度为2.5 μm,电极厚度为0.2 μm,微环半径为13.76 μm,微环与信道间的耦合间距为0.14 μm,输出光谱的3 dB带宽约为0.05 nm,开关电压约为12.6 V,插入损耗约为0.67~1.26 dB,串扰小于－20 dB,开关时间约为11.35 ps.     

Single-photon all-optical switching using coupled microring resonators

We study the nonlinear phase response of a microring resonator coupled to a bus waveguide and the use of this nonlinear phase shift to store information in the microring resonator and enhance the switching characteristics of a Mach-Zehnder interferometer (MZI). By introducing coupling between adjacent microring resonators, the switching characteristics of the MZI can be exponentially enhanced as a function of the number of microring resonators, when compared to the linear enhancement for uncoupled resonators. With only a few moderate-finesse microring resonators, the switching power can be reduced to attowatt level, allowing for photonic switching devices that operate at single-photon level in ordinary optical waveguides.      

Electro-optically tunable microring resonators on lithium niobate

Electro-optical tuning of a microring resonator fabricated on lithium niobate (LiNbO3) is presented. The device structure, including microring resonator and couplers, is designed in detail and is produced by titanium diffusion on the wet-etched LiNbO3 ridge surface. The resonance wavelengths for TM and TE polarizations can be tuned by electro-optic effect. The output characteristics of through port and drop port in the microring resonators are measured, and the effect of applied voltage on the shift of resonant wavelength is discussed. The presented microring resonators have the features of fast tuning speed, high material stability, bidirection wavelength shift, and no heating interference. Realization of such a microring resonator on LiNbO3 makes the utilization of electro-optic tuning and nonlinear effects in the versatile photonic applications of microring resonators achievable.     

Multi-soliton generation with extremely narrow free spectrum range for multiplexed sensors via optical network

We propose a new system of multiplexer sensors using the localized soliton pulse generated by a microring resonator in optical networks. A large bandwidth signal is generated by a soliton pulse propagating within the microring resonator, which is allowed to form the multiplexed sensors. Two forms of soliton pulses are generated and localized, i.e. temporal and spatial solitons. The required soliton pulses with specified wavelengths can be localized and formed the sensing. This is formed by using an optical add/drop multiplexer incorporating in the optical network, where the localized soliton pulses are available for add/drop signals to/from the optical network. The change in physical parameter measured the change in soliton wavelength, which formed the measurement.     

High-performance and fabrication friendly polarization demultiplexer

A compact and fabrication friendly polarization demultiplexer (P-DEMUX) is proposed and characterized to enable wavelength-division-multiplexing and polarization-division-multiplexing simultaneously. The proposed structure is composed of a polarization-selective microring resonator in ultrathin waveguide and two bus channels in the silicon nitride-silica-silicon horizontal slot waveguides. In the slot waveguide, the transverse electric (TE) mode propagates through the silicon layer, while the transverse magnetic (TM) mode is confined in the slot region. In the designed ultra-thin waveguide, the TM mode is cut-off. The effective indexes of the TE modes for ultrathin and slot waveguides have comparable values. Thanks for these distinguishing features, the input TE mode can be efficiently filtered through the ultra-thin microring at the resonant wavelength, while the TM mode can directly output from the through port. Simulation results show that the extinction ratio of the proposed P-DEMUX for TE and TM modes are 33.21 dB and 24.97 dB, and the insertion losses are 0.346 dB and 0.324 dB, respectively, at the wavelength of 1551.64 nm. Furthermore, the device shows a broad bandwidth ($>100$ nm) for an extinction ratio (ER) of $>20$ dB. In addition, the proposed P-DEMUX also has a good fabrication tolerance for the waveguide width variation of $-20$ nm$\le \Delta w_{\rm g}\le 20$ nm and the microring width variation of $-20$ nm$\le \Delta w_{\rm r}\le $20 nm for a low insertion loss of $<0.75$ dB and low ER of $<-18$ dB.     

Wide-range tuning of polymer microring resonators by the photobleaching of CLD-1 chromophores

We present a simple and effective method for the postfabrication trimming of optical microresonators. We photobleach CLD-1 chromophores to tune the resonance wavelengths of polymer microring resonator optical notch filters. A maximum wavelength shift of -8.73 nm is observed. The resonators are fabricated with a soft-lithography molding technique and have an intrinsic Q value of 2.6 x 10(4) and a finesse of 9.3. The maximum extinction ratio of the resonator filters is -34 dB, indicating that the critical coupling condition has been satisfied.     

Wavelength-selective 4 × 4 nonblocking silicon optical router for networks-on-chip

We design and fabricate a wavelength-selective nonblocking 4 × 4 silicon optical router based on microring resonator for use in future integrated photonic interconnection networks. We successfully demonstrate 12 possible I/O routing paths and present 13 nonblocking operating states, including four broadcasting states, with worst-case extinction ratio and cross talk of 21.05 and -21.56 dB, respectively. Thermal tuning is employed to compensate the resonance shift of microring resonators caused by fabrication errors and adjust the resonance to match the International Telecommunication Unit grid with the channel spacing of 100 GHz.     

Slotted Photonic Crystal Microring Resonators

We propose using a slotted photonic crystal nanobeam to construct a microring resonator. The transmission characteristics of the slotted photonic crystal nanobeam and the microring resonator are demonstrated by two-dimensional finite-difference time-domain simulation, and the mechanism of these characteristics is analyzed considering the introduction of the slot. The refractive index sensitivity of the slotted photonic crystal microring resonator is evaluated to be larger than those of a slot waveguide microring resonator and a nonslotted photonic crystal microring resonator.     

Analysis of polymer electro-optic microring resonator switches

The structure and the principle for the polymer electro-optic microring resonator (MRR) switch are proposed as well as the transfer functions. The structural parameters are optimized; the transmission characteristics are analyzed including the output power, switching time, switching voltage, insertion loss, and crosstalk. When the operation voltage is 0 V, the insertion loss and crosstalk are ∼1.2 and −20.2 dB, respectively; when the operation voltage is 10.0 V, those are ∼0.35 and −20.0 dB, respectively. Furthermore, a novel method is presented for analyzing time-domain response of the device and the switching time is determined to be ∼10.71 ps. These results indicate the favorable switching functions of the designed device.     

A microring resonator with an integrated Bragg grating: a compact replacement for a sampled grating distributed Bragg reflector

We present analysis of the distributed Bragg reflector in a microring resonator (DBR-MRR) structure. With appropriate design parameters, the device can closely reproduce the reflectance spectrum of a sampled grating distributed Bragg reflector (SGDBR). By inserting the grating inside a microring resonator, the structure is much more compact than an SGDBR, suppresses side mode ripples near each peak, and offers better control over its full width half maximum (FWHM). The device is expected to have applications in compact tunable lasers and other planar photonic devices.     

Design, fabrication and characterization of a high-performance microring resonator in silicon-on-insulator

A high-performance microring resonator in a silicon-on-insulator rib waveguide is realized by using the electron beam lithography followed by inductively coupled plasma etching. The design and the experimental realization of this device are presented in detail. In addition to improving relevant processes to minimize propagation loss, the coupling efficiency between the ring and the bus is carefully chosen to approach a critical coupling for high performance operating. We have measured a quality factor of 21,200 and an extinction ratio of 12.SdB at a resonant wavelength of 1549.32nm. Meanwhile, a low propagation loss of 0.89dB/mm in a curved waveguide with a bending radius of 40μm is demonstrated as well.     

Generating entangled photons via enhanced spontaneous parametric downconversion in AlGaAs microring resonators

Spontaneous parametric downconversion (SPDC) can be enhanced in double-channel side-coupled microring resonator structures, generating entangled photons spatially separated in different channels. The enhancement is even more drastic in single-channel side-coupled microring resonator structures, although the generated entangled photons are not spatially separated, and it might be most interesting to use a ring tuned for nondegenerate SPDC.     

空间用调Q偏振耦合输出棱镜谐振腔特性分析

为了优化棱镜谐振腔在调Q状态下的运转特性,充分利用琼斯矩阵光学分析棱镜谐振腔的特性,在不同材料棱镜情况下,比较了可变输出耦合率、泡克耳斯盒的消光比以及输出耦合率的调节.得到泡克耳斯盒在四分之一波长电压下能够得到比半波长电压更高的消光比,从而更适合在调Q工作状态下工作.     

Filter synthesis for periodically coupled microring resonators

The theory of filter synthesis using periodically coupled microring resonators is developed as a means to overcome the fabrication sensitivities inherent in conventional higher-order filters, while still achieving desirable spectral characteristics. Each resonator in the array can compensate for deficiencies in any of the others. These filters exhibit a boxlike shape and very high extinction ratios.     

光梯度力驱动的纳米硅基光开关

通过一道光改变另一道光的传输路线是光子集成网络中重要而长远的目标, 然而, 由于硅材料的光学非线性较弱, 在硅材料上实现开关的全光控制难以实现. 因此本文提出了一种由光梯度力驱动的纳米硅基光开关, 实现了硅基光开关的全光控制. 该光开关由一个部分悬空的微环谐振器和一个交叉波导结构构成, 当通入一道控制光时, 悬空的微环谐振器在光梯度力的作用下发生弯曲, 微环谐振器的谐振波长随之发生变化, 从而实现光信号的传输路线发生改变. 该光开关利用纳米光子制造技术在标准绝缘体上硅晶圆上制造, 实验数据得出其最小消光比为10.67 dB, 最大串扰为 -11.01 dB, 开关时间分别为180 ns和170 ns. 该光开关具有尺寸小, 响应速度快, 低损耗和可拓展等优点, 在片上集成光路、高速信号处理以及下一代光纤通信网络中具有潜在应用.