化妆品前处理的研究

本文研究了压力罐一次性消解化妆品试样，并探讨了不同消化剂及其用量，消化时间及温度对其汞、砷、铅测定的影响。采用本文的前处理方法，再按国际规定方法测定汞、砷、铅的含量，其加标回收率分别为Hg95.0%-103.8%;As98.0%-109.0%;Pb98.0%-102.6%，6次测定标准物质中汞、砷、铅的结果均与其标准值吻合，相对标准偏差均小于5.0%。结果表明，该法为一种高效、经济、实用且较为理想的前处理方法。     

分析北京城市污泥中铅砷镉形态浓度的ICP-MS

城市污泥中重金属的难降解和高毒性限制了污泥的资源化利用.以北京G和Q污水处理厂的压滤出厂污泥为实验材料,采用BCR三步浸提法对污泥中铅砷镉Pb,As,Cd的三种形态进行提取,以HNO3-HClO4进行全量消解,利用ICP-MS检测Pb,As,Cd的全量和各形态的含量,从而为北京城市污泥的资源开发研究提供基础数据.实验结果表明,北京城市污泥中Pb和Cd含量比上世纪末明显降低:其中,G污泥中Pb,As,Cd的全量(干重)分别为19.60,37.96和1.34 mg·kg-1,而Q污泥中分别为19.58,23.46和2.30 mg·kg-1;两种污泥中Pb含量相差甚微,G污泥中As明显高于Q污泥,而Cd则显著低于后者;两种污泥中相应金属的三种形态的变化趋势基本一致:Pb与As以HAc酸溶态为主,H2O2可氧化态最少;而Cd主要以NH2OH-HCl可还原态存在,HAc酸溶态最少.三种重金属中生物毒性大的形态均占70%以上.     

同一种前处理方法测定烟草中砷、铅和镉

采用同一种前处理方法即硝酸和高氯酸消解处理烟草样品后,氢化物发生-原子荧光光谱法测定烟叶中砷、铅;原子吸收光谱法测定烟叶中镉。样品溶液介质为10%的盐酸,对7个样品平行3次重复实验,其相对标准偏差为砷:0.81%—4.96%、铅:2.82%—5.83%、镉:0.96%—4.60%,砷、铅、镉的检测线性范围分别为:0.0—120.0、0.0—60.Oμg·L^-1和0.0—800.0μg·L^-1,加标回收率:砷在94.5%—96.9%之间、铅在92.7%—101.6%之间、镉在102.2%—110.9%之间。     

ICP-AES测定5种止咳类中药材重金属含量

采用硝酸-高温灰化对5种止咳类中药材中金属元素进行消解,用电感耦合等离子体-原子发射光谱法测定了试样中Pb、Cu、Cr、Cd、As 5种重金属元素含量。结果表明,5种止咳类中药材中重金属含量差异显著,铅元素在紫菀、枇杷叶和白前3种中药材中的含量超过国家标准,砷元素在紫菀、白前、杏仁和前胡4种中药材中的含量也超过了国家标准,不利于这些药材的药用和出口。该法中加标回收率为93.87%—99.21%,相对标准偏差为0.42%—3.22%（n=6）,具有良好的精密度和准确度。可作为该类中药材重金属含量快速检测和控制的方法。     

不同产地吉祥草中重金属的含量测定

测定吉祥草中重金属及有害元素含量,比较不同产地吉祥草中的Cu、Pb、As、Cd、Hg 5种元素的含量.采用原子吸收光谱法测定铅、铜、砷含量,用原子荧光光谱法测定汞、镉含量.吉祥草药材中汞、镉、砷含量均低于国家限量标准,个别地区吉祥草药材中铜、铅含量高于国家限量标准.本文为科学地制定吉祥草药材中重金属限量标准,提高吉祥草...     

ICP-AES法测定黄芪成分F3新制剂中微量元素

采用高压密封消化罐 (PTFE) ,以 (4 1)硝酸 -高氯酸为溶样试剂 ,采用电感耦合等离子体原子发射光谱法 (ICP- AES)测定黄芪成分 F3新制剂中铁、锰、铜、锌、铬、锶、硒、铅、砷、镉等微量元素。方法回收率为 94 .2 %— 10 6 .3% ,相对标准差为 4 .1%— 7.9%。黄芪成分 F3新制剂含有多种重要微量元素 ,不含有铅、砷、镉等有害元素。     

微波消解-电感耦合等离子体-质谱法测定大米中的铅、镉、汞和砷

应用微波消解-电感耦合等离子体-质谱法(ICP-MS)一次进样同时测定大米中的铅、镉、汞、砷含量.采用8mL硝酸+2mL过氧化氢的微波消解体系,消解后无需赶酸,定容后直接用ICP-MS测定.实验发现,运用该方法干扰少,速度快,多元素同时分析,重现性好,准确度高.该方法的回收率分别为:Pb:100.9％、Cd:90.1％、Hg:86.1％、As:92.8％.Pb、Cd、Hg、As方法检出限均为0.001ng/mL.     

北京城市污泥中铅砷镉形态浓度的ICP-MS分析

城市污泥中重金属的难降解和高毒性限制了污泥的资源化利用。以北京G和Q污水处理厂的压滤出厂污泥为实验材料,采用BCR三步浸提法对污泥中铅砷镉Pb,As,Cd的三种形态进行提取,以HNO₃-HClO₄进行全量消解,利用ICP-MS检测Pb,As,Cd的全量和各形态的含量,从而为北京城市污泥的资源开发研究提供基础数据。实验结果表明,北京城市污泥中Pb和Cd含量比上世纪末明显降低：其中,G污泥中Pb,As,Cd的全量(干重)分别为19.60,37.96和1.34 mg·kg-1,而Q污泥中分别为19.58,23.46和2.30 mg·kg-1;两种污泥中Pb含量相差甚微,G污泥中As明显高于Q污泥,而Cd则显著低于后者;两种污泥中相应金属的三种形态的变化趋势基本一致：Pb与As以HAc酸溶态为主,H₂O₂可氧化态最少;而Cd主要以NH₂OH-HCl可还原态存在,HAc酸溶态最少。三种重金属中生物毒性大的形态均占70％以上。     

不同产地几种中药材中重金属含量测定及砷的形态分析

通过对不同产地几种中药材中砷、铅、镉、铜以及无机砷、三价砷含量的分析测定,得出样品中砷、铅、镉、铜以及无机砷、无机三价砷的测定RSD〈3%,加标回收率在91.32%—109.7%之间。11个样品的总砷含量在0.047—1.681μg/g之间,均低于2μg/g;无机砷含量为0.023—1.294μg/g;无机三价砷含量为0.019—0.918μg/g;铅含量两份样品未检出,其余样品为0.007—0.786μg/g,均低于5μg/g;镉的测定,两份样品未检出,其余样品含量为0.007—2.129μg/g,其中两份样品大于0.3μg/g;铜含量为4.441—14.07μg/g,均低于20μg/g。研究发现同种药材不同产地的重金属含量差异较大,部分产地金银花中镉含量超标严重,无机砷和三价砷含量相对较高,需引起重视。     

不同种群蜈蚣草中砷形态的X射线吸收光谱研究

研究选择了分布于我国安徽、重庆、湖南、台湾、福建、广西、广东等7个省、市、自治区中10个不同地理区域的13个蜈蚣草种群,通过同步辐射X射线吸收光谱研究不同种群蜈蚣草中的砷形态差异,为揭示其富集机理奠定基础。蜈蚣草根部的砷主要以与O结合的方式存在,各种群的蜈蚣草根部还存在As—S配位的砷,但含量较少。蜈蚣草根部中的砷以As(Ⅴ)为主,As(Ⅴ)的比例为59.6%±0.6%~83.8%±3.8%。不同种群的根部砷形态具有较大差异,HN5种群具有明显高于其他种群的As(Ⅲ)比例,FJ种群具有明显低于其他种群的As(Ⅲ)比例,而来自湖南和广西的几种种群具有较高的As-GSH比例。As(Ⅴ)比例由低到高的顺序为:HN5GX2HN1CQGX1GDHN3HN4GX3HN2TWAHFJ。与根部相似,蜈蚣草羽片中的砷主要以和O结合的形式存在,存在As—S配位,但比例较低。与根部不同,羽片中的砷以As(Ⅲ)为主,基本不存在As(Ⅴ)形式。羽片砷主要由As(Ⅲ)和As-GSH两种组分组成。AsGSH组分比例为2.4%~12.9%,GX1种群中As-GSH比例最低,而GD种群中As-GSH比例最高。AsGSH比例由高到低的顺序为GDHN3HN1TWCQAHFJHN5HN2GX2GX3HN4GX1。对蜈蚣草中砷形态的种群差异揭示有利于对蜈蚣草砷富集能力的种群差异来源机制进行深入研究。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.