Poly(vinyl chloride)-<Emphasis Type="Italic">graft</Emphasis>-poly(<Emphasis Type="Italic">N</Emphasis>-vinyl caprolactam) graft copolymer: synthesis and use as template for porous TiO<Subscript>2</Subscript> thin films in dye-sensitized solar cells

Poly(N-vinyl caprolactam) (PNVCL) side chains were grafted to a poly(vinyl chloride) (PVC) backbone via atom transfer radical polymerization. The synthesized PVC-g-PNVCL graft copolymer was templated for the preparation of porous TiO₂ thin films, which involved a sol–gel reaction and calcination process. The interaction of the carbonyl groups in the PVC-g-PNVCL with the titania was revealed by FT-IR spectroscopy. X-ray diffraction and transmission electron microscopy analysis showed the formation of porous TiO₂ thin films with the anatase phase. A series of porous TiO₂ thin films with different pore sizes and porosities was prepared by varying the solution compositions and were used as photoelectrodes in dye-sensitized solar cells (DSSC) with a polymer electrolyte. The DSSC performed best when using the TiO₂ film with higher porosity, lower interfacial resistance, and longer electron life time. The highest energy conversion efficiency, photovoltage (V _oc), photocurrent density (J _sc), and fill factor (FF) were 1.2%, 0.68 V, 3.2 mA/cm², and 0.57 at 100 mW/cm², respectively, for the quasi-solid state DSSC with a 730-nm-thick TiO₂ film.     

Symbiotic organism search algorithm for simulation of <Emphasis Type="Italic">J</Emphasis>-<Emphasis Type="Italic">V</Emphasis> characteristics and optimizing internal parameters of DSSC developed using electrospun TiO<Subscript>2</Subscript> nanofibers

In the present investigation, the recently developed, simple, robust, and powerful metaheuristic symbiotic organism search (SOS) algorithm was used for simulation of J-V characteristics and optimizing the internal parameters of the dye-sensitized solar cells (DSSCs) fabricated using electrospun 1-D mesoporous TiO₂ nanofibers as photoanode. The efficiency (η =?5.80%) of the DSSC made up of TiO₂ nanofibers as photoanode is found to be ～ 21.59% higher compared to the efficiency (η =?4.77%) of the DSSC made up of TiO₂ nanoparticles as photoanode. The observed high efficiency can be attributed to high dye loading as well as high electron transport in the mesoporous 1-D TiO₂ nanofibers. Further, the validity and advantage of SOS algorithm are verified by simulating J-V characteristics of DSSC with Lambert-W function.     

Laser Sintering of a Porous TiO2 Film in Dye-Sensitized Solar Cells

We investigate the possibility of modifying the porous structure of TiO₂ films in dye-sensitized solar cells (DSSC) in its sintering by a pulsed Nd:YAG laser (wavelength 1064 nm) to improve their parameters and characteristics. Sintering at various pulse energies enabled a porosity within the range of 0.45 to 0.20. The efficiency of the energy conversion in experimental DSSC specimens with TiO₂ films sintered by an optimum laser-radiation pulse energy of 150 mJ was 20–25% higher than that of commercial solar cells.     

Optimum oxide thickness for dye-sensitized solar cells—effect of porosity and porous size. A numerical approach

The microstructure of the metal semiconductor oxide which forms the heart of a dye-sensitized solar cell (DSSC) has proved to play a key role in the enhancement of photoelectric conversion efficiency of the cell. In this work, a numerical simulation of the system TiO₂ photo-sensitive dye of a TiO₂ DSSC focuses on the effect that the oxide porosity and the size of the pores have on the cell's performance. The steady-state numerical model used is based on the continuity and transport equations for charge species involved in the system, in connection to Poisson's equation. Light absorption coefficient is set dependent on both porosity and the size of pores in TiO₂. At a first approximation, electron mobility is considered dependent upon porosity following an iteration procedure dependent also upon local field in the oxide. An effective dielectric constant dependent upon the porosity of TiO₂, as well, is used in the model. Electron lifetime in the bulk is set dependent upon electron distribution following the iteration procedure with electron lifetime at the surface taking into consideration surface recombination. Results for different values of TiO₂ porosity and pores' size in connection to the oxide thickness are discussed and found in accordance with results reported in the literature.     

Analysis of adsorption properties of N719 dye molecules on nanoporous TiO2 surface for dye-sensitized solar cell

Ordered nanoporous TiO₂ materials (MK-TiO₂, MS-TiO₂, and MU-TiO₂) were synthesized for the dye-sensitized solar cell (DSSC) by using different silica templates such as KIT-6, SBA-15, and MSU-H. To prepare a photoelectrode in DSSC, cis-bis(isothiocyanato)bis(2,2′-bipyridyl-4,4′-dicarboxylato)-ruthenium(II)bis-tetrabutylammonium dye (N719) was adsorbed onto the synthesized nanoporous TiO₂ materials. The samples were characterized by XRD, TEM, FE-SEM, AFM, and N₂ adsorption analyses. The photovoltaic performance of DSSC was evaluated from the overall conversion efficiency, fill factor, open-circuit voltage, and short-circuit current from the I-V curves measured. It was found that the photoelectric performance is highly dependent on the adsorption properties of N719 dye molecules on the nanoporous TiO₂ replicas (MK-TiO₂, MS-TiO₂, and MU-TiO₂) synthesized from different silica templates.     

Hydrothermal growth of large-scale macroporous TiO<Subscript>2</Subscript> nanowires and its application in 3D dye-sensitized solar cells

Large-scale macroporous TiO₂ nanowires (MTN) were directly grown on spiral-shaped titanium wires as photoanodes of dye-sensitized solar cells (DSSCs) via a facile hydrothermal reaction without any seeds, templates, and TiO₂ powder. The MTN thin film was characterized by SEM, XRD and TEM. The studies revealed that the MTN thin film had better mechanical properties and provided an efficient pathway for the diffusion of liquid electrolyte. The efficiency of 0.86% for the 3D DSSC was obtained with a J _sc of 2.30 mA/cm², V _oc of 616 mV, and FF of 0.61. This MNT-based mini 3D DSSC is a promising photovoltaic device for applications in the fields of high-integrated micro-electronic equipment.     

Dye sensitized solar cells prepared by flames stabilized on a rotating surface

A previously developed flame synthesis method was applied to the preparation of mesoporous titania films for application in dye sensitized solar cells (DSSC). The method combines the synthesis of narrowly sized, ultrafine metal oxide particles with controllable chemical and phase purity and the deposition of these particles into a uniform, porous thin film in a single step. The current work used a series of ethylene–oxygen–argon flames to produce DSSC anode films of wide ranging properties. The performance of the solar cells prepared with these anode films was studied at the fundamental level with respect to variations of the titania crystal phase purity and content resulting from changes primarily from flame stoichiometry changes. Based on the basic relationship established among flame synthesis condition-material property-cell performance, a highly efficient DSSC was designed, which shows photocurrent densities better than some of the best performing cells reported to date. Additional studies have focused on a demonstration of the suitability of the flame process in engineering TiO₂ films structurally and chemically with the potential of further improved DSSC efficiency.     

Photoelectrochromic properties of NiO film deposited on an N-doped TiO2 photocatalytical layer

N-doped TiO₂ film was synthesized on indium–tin oxide (ITO) conducting glass substrate by the hydrolysis method and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Then high porous NiO was deposited onto the TiO_2?xN_x layer by chemical bath deposition (CBD) to prepare a double-layer TiO_2?xN_x/NiO electrode. The photoelectrochromic properties of the TiO_2?xN_x/NiO electrode were discussed through the results of UV–vis transmittance spectra, cyclic voltammogram and photocurrent transient measurements. It was found that the TiO_2?xN_x/NiO electrode was sensitive to light and exhibited a noticeable photoelectrochromism. The NiO film changed its color from colorless to brown, and the transmittance varied from 86.8% to 14.5% at 500 nm after 1 h irradiation.     

Mesoporous titania films investigated by positron annihilation based on a slow positron beam

Tunable mesoporous titania (TiO₂) thin films were synthesized via a sol-gel method using an amphiphilic triblock copolymer F38 as the structural template. The dependence of crystalization, pore morphology and interconnectivity of TiO₂ films on the weight ratio of F38 was studied by wide-angle X-ray diffraction, field emission scanning electron microscopy and Doppler broadening of positron annihilation radiation spectroscopy based on a slow positron beam. By loading more F38, the crystallization of TiO₂ films is enhanced, accompanied by a decrement in oxygen vacancies/grain boundaries. Smaller and isolated mesopores are formed in the films prepared with F38 less than 15?wt%. The pore percolation occurs when the weight ratio of F38 is up to 20?wt% and larger and interconnected worm-like pores are formed.     

Enhanced optical properties of Al-doped TiO2 thin films in oxygen or nitrogen atmosphere

Al-doped TiO₂ (TiO₂:Al) films were deposited by simultaneous RF magnetron sputtering of TiO₂ and DC magnetron sputtering of Al. The advantage of this method is that the Al content could be independently controlled. By depositing in a mixed Ar-O₂ or a mixed Ar-N₂ atmosphere, the TiO₂:Al film became more stoichiometric and the nanocrystallinity was enhanced. The nonlinear refractive index of TiO₂:Al film deposited in a pure Ar, a mixed Ar-O₂ or a mixed Ar-N₂ atmosphere was measured by Moiré deflectometry, and was of the order of 10⁻⁸ cm² W⁻¹. For the TiO₂:Al film deposited in a pure Ar atmosphere, the porosity was higher corresponding to the lower transmission. However, the porosity of TiO₂:Al film decreased as the oxygen or nitrogen pressure increased. Especially, as the ratio of O₂ to Ar pressure increased to 0.22, TiO₂:Al film exhibited lower porosity, higher visible transmission, higher linear refractive index, lower stress and lower stress-optical coefficient.     

TiO2 treatment using ultrasonication for bubble cavitation generation and efficiency assessment of a dye-sensitized solar cell

In this study, the impacts of different ultrasonic treatments on TiO₂ particles were determined and they were used to manufacture the photoelectrodes of a dye-sensitized solar cell (DSSC). Two methods were used to prepare TiO₂ particles directly sonicated by an ultrasonic horn, and TiO₂ treated indirectly by an ultrasonic cleaner. TEM, XPS analysis was confirmed that cavitation bubbles generated during ultrasonication resulted in defects on the surface of TiO₂ particles, and the defect induced surface activation. To understand the effect of TiO₂ surface activation on energy conversion efficiency of DSSC, ultrasonic horn DSSC and ultrasonic cleaner DSSC were prepared. The UV–vis analysis exhibited that the ultrasonic horn DSSC possessed higher dye adsorption when compared to the ultrasonic cleaner DSSC, and the EIS analysis confirmed that the electron mobility was greatly increased in the ultrasonic horn DSSC. The energy conversion efficiency of the ultrasonic horn DSSC was measured to be 3.35%, which is about 45% increase in comparison to that of the non-ultrasonic treated DSSC (2.35%). In addition to this regard, recombination resistance of ultrasonic horn DSSC was calculated to be 450 Ω·cm², increasing more than two times compared to the non-ultrasonic treated DSSC (200 Ω·cm²). Taken together, these ultrasonic treatments significantly improved the energy conversion efficiency of DSSC, which was not tried in DSSC-related research, and might lead us to develop more efficient practical route in the manufacturing of DSSC.     

Influence of porous morphology on optical dispersion properties of template free mesoporous titanium dioxide (TiO2) films

This paper focuses the influence of porous morphology on the microstructure and optical properties of TiO₂ films prepared by different sol concentration and calcination temperatures. Mesoporous TiO₂ thin films were prepared on the glass substrates by sol-gel dip coating technique using titanium (IV) isopropoxide. Porous morphology of the films can be regulated by chemical kinetics and is studied by scanning electron microscopy. The optical dispersion parameters such as refractive index (n), oscillator energy (E_d), and particle co-ordination number (N_c) of the mesoporous TiO₂ films were studied using Swanepoel and Wemple-DiDomenico single oscillator models. The higher precursor concentration (0.06 M), films exhibit high porosity and refractive index, which are modified under calcination treatment. Calcinated films of low metal precursor concentration (0.03 M) possess higher particle co-ordination number (N_c = 5.05) than that of 0.06 M films (N_c = 4.90) due to calcination at 400 °C. The lattice dielectric constant (E_∞) of mesoporous TiO₂ films was determined by using Spintzer model. Urbach energy of the mesoporous films has been estimated for both concentration and the analysis revealed the strong dependence of Urbach energy on porous morphology. The influence of porous morphology on the optical dispersion properties also has been explained briefly in this paper.     

TiO2表面质子化对染料敏化太阳能电池性能及吸附染料稳定性的影响

采用致密平整TiO₂薄膜作为染料敏化太阳能电池光电极,并研究了HCl处理表面质子化对电池性能的影响. 结果表明,HCl处理后电池的短路电流显著提升,电池的开路电压则有轻微的下降,电池电流提升了31%,而能量转化效率则提升了25%. 这是因为TiO₂的表面质子化增强了吸附染料与TiO₂间的电学耦合,提高了染料中激发电子向TiO₂导带的注入速率. 而电压的下降,一方面是由于质子化会引起TiO₂导带能级     

Chemical reactions in TiO2/SnO2/TiCl4 hybrid electrodes and their impacts to power conversion efficiency of dye-sensitized solar cells

This study examined the applicability of TiO₂/SnO₂/TiCl₄ hybrid electrodes in dye-sensitized solar cells (DSSCs) by combining chemical modeling with experimentation. The interfacial chemical reactions in a TiO₂/SnO₂/TiCl₄ system were simulated using a thermochemistry software package, which led to the design and testing of hybrid working electrodes. Chemical thermodynamic modeling proved that TiCl₄ is an effective agent in removing Tiⁿ⁺ (n<4) and Sn^m+ (m<4) ion impurities from dry-mixed TiO₂/SnO₂ composite particles. Our results demonstrate that the power conversion efficiency of DSSC with a TiO₂/SnO₂/TiCl₄ hybrid electrode exceeds that of the conventional DSSC with a TiO₂ electrode due to the effects of light-scattering and the formation of additional absorbance (SnCl₂), which is an unexpected side effect of TiCl₄ treatment enabling the absorption of visible light. The proposed approach is ideally suited to establishing relationships between chemistry theory and the structure and performance of advanced DSSCs as well as photo-electro-chemical systems.     

Preparation and study of microstructures, optical properties and oscillator parameters of titanium (IV) oxide (TiO2) film

In this study, Titanium (IV) Oxide (TiO₂) film has been prepared and characterized by X-ray diffraction (XRD). The XRD pattern of TiO₂ film of anatase phase exhibit very sharp peaks at 25° and 47.85°. According to Scherrer??s formula the grain size of anatase (101) phase TiO₂ nananoparticle is 38.5 nm. The optical properties and constants of TiO₂ film of thickness (4 ??m) have been investigated at room temperature. The transmittance, reflectance and absorbance spectra are measured in the wavelength range (340?C900 nm). Optical constants of TiO₂ film are derived from the transmission spectra and the refractive index dispersion of the film. The oscillator energy, E ₀ dispersion energy, E _d , the static refractive index, n ₀, and other parameters have been determined by the single oscillator Wemple-DiDomenico method. This film can be used in the form of thin film in dye-sensitized solar cells.     

Improving the visible light photocatalytic activity of mesoporous TiO2 via the synergetic effects of B doping and Ag loading

B-doped together with Ag-loaded mesoporous TiO₂ (Ag/B–TiO₂) was prepared by a two-step hydrothermal method in the presence of boric acid, triblock copolymer surfactant, and silver nitrate, followed by heat treatment. The obtained samples were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), UV–vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption–desorption. It was revealed that all samples consist of highly crystalline anatase with mesoporous structure. For Ag/B–TiO₂, B was doped into TiO₂ matrix in the form of both interstitial B and substitutional B while Ag was deposited on the surface of B–TiO₂ in the form of metallic silver. Compared with the single B-doped or Ag-loaded TiO₂ one, mesoporous Ag/B–TiO₂ exhibits much higher visible light photocatalytic activity for the degradation of Rhodamine 6G, which can be ascribed to the synergistic effects of B doping and Ag loading by narrowing the band gap of the photocatalyst and preventing the fast recombination of the photogenerated charge carriers, respectively.     

Positron annihilation studies of mesoporous silica films using a slow positron beam

Positron annihilation lifetime spectra were measured for mesoporous silica films, which were synthesized using triblock copolymer (EO₁₀₆PO₇₀EO₁₀₆) as a structure-directing agent. Different positron lifetime spectra for the deposited and calcined films indicated the formation of meso-structure after calcination, which was confirmed by Fourier transform infrared (FTIR) spectra and field emission-scanning electron microscopy (FE-SEM) observation. Open porosity or pore interconnectivity of a silica film might be evaluated by a two-dimensional positron annihilation lifetime spectrum of an uncapped film. Pore sizes and their distributions in the silica films were found to be affected by thermal treatments.     

Dye-sensitized solar cells based on ZnO nanowire array/TiO2 nanoparticle composite photoelectrodes with controllable nanowire aspect ratio

The ZnO nanowire (NW) array/TiO₂ nanoparticle (NP) composite photoelectrode with controllable NW aspect ratio has been grown from aqueous solutions for the fabrication of dye-sensitized solar cells (DSSCs), which combines the advantages of the rapid electron transport in ZnO NW array and the high surface area of TiO₂ NPs. The results indicate that the composite photoelectrode achieves higher overall photoelectrical conversion efficiency (η) than the ZnO NW alone. As a result, DSSCs based on the ZnO NW array/TiO₂ NP composite photoelectrodes get the enhanced photoelectrical conversion efficiency, and the highest η is also achieved by rational tuning the aspect ratio of ZnO NWs. With the proper aspect ratio (ca. 6) of ZnO NW, the ZnO NW array/TiO₂ NP composite DSSC exhibits the highest conversion efficiency (5.5 %). It is elucidated by the dye adsorption amount and interfacial electron transport of DSSCs with the ZnO NW array/TiO₂ NP composite photoelectrode, which is quantitatively characterized using the UV-Vis absorption spectra and electrochemical impedance spectra. It is evident that the DSSC with the proper aspect ratio of ZnO NW displays the high dye adsorption amount and fastest interfacial electron transfer.     

Photocatalytic hydroxyapatite/titanium dioxide multilayer thin film deposited onto glass using an rf magnetron sputtering technique

Hydroxyapatite (HA)/titanium dioxide (TiO₂) thin film was deposited on glass using a radio frequency magnetron sputtering. X-ray diffraction (XRD), Fourier-transform infrared spectrometry, ultraviolet-visible spectroscopy and measurement of its photocatalytic activity by the decomposition of formaldehyde gas and the bacterial survival test of Escherichia coli (E. coli) cells were applied to characterize the film. After heat treatment (at 500 °C), XRD analysis of the HA/TiO₂ film showed a crystalline TiO₂ crystal structure with anatase phase. The transmittance of the HA/TiO₂ film decreased after the heat treatment, however, the average transmittance remained at 87% in the visible light range.In the decomposition of formaldehyde gas, the HA/TiO₂ film showed a higher decomposition rate than either the TiO₂ or the HA film alone. However, in the bacterial survival test, survival of cells on the HA/TiO₂ film was higher than that on the TiO₂ film, which indicates the HA/TiO₂ film has a lower bactericidal effect than the TiO₂ film alone.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.