Structural, vibrational, thermal, and conductivity studies on proton-conducting polymer electrolyte based on poly (N-vinylpyrrolidone)

The proton-conducting polymer electrolytes based on poly (N-vinylpyrrolidone) (PVP), doped with ammonium chloride (NH₄Cl) in different molar ratios, have been prepared by solution-casting technique using distilled water as solvent. The increase in amorphous nature of the polymer electrolytes has been confirmed by XRD analysis. The FTIR analysis confirms the complex formation of the polymer with the salt. A shift in glass transition temperature (T _g) of the PVP/NH₄Cl electrolytes has been observed from the DSC thermograms which indicates the interaction between the polymer and the salt. From the AC impedance spectroscopic analysis, the ionic conductivity of 15?mol% NH₄Cl-doped PVP polymer complex has been found to be maximum of the order of 2.51?×?10^?5?Scm^?1 at room temperature. The dependence of T _g and conductivity upon salt concentration has been discussed. The linear variation of the proton conductivity of the polymer electrolytes with increasing temperature suggests the Arrhenius type thermally activated process. The activation energy calculated from the Arrhenius plot for all compositions of PVP doped with NH₄Cl has been found to vary from 0.49 to 0.92?eV. The dielectric loss curves for the sample 85?mol% PVP:15?mol% NH₄Cl reveal the low-frequency ?? relaxation peak pronounced at high temperature, and it may be caused by side group dipoles. The relaxation parameters of the electrolytes have been obtained by the study of Tan?? as a function of frequency.     

Automatic dispersion,long-term stability of multi-walled carbon nanotubes in high concentration electrolytes

Nanoparticles have been known as the useful materials in working fluids for petroleum industry. But the stabilization of nano-scaled materials in water-based working fluids at high salinities is still a big challenge. In this study, we successfully prepared the anionic polymer/multi-walled carbon nanotubes (MWNTs) composites by covalently wrapping of MWNTs with poly (sodium 4-styrenesulfonate) (PSS) to improve the stability of MWNTs in high concentration electrolytes. The PSS/MWNTs composites can automatically disperse in salinity up to 15 wt% NaCl and API brines (8 wt% NaCl?+?2 wt% CaCl₂). Hydrodynamic diameters of composites were measured as a function of ionic strength and API brines by dynamic light scattering (DLS). By varying the concentration of brines, hydrodynamic diameter of PSS/MWNTs composites in brines fluctuated between 545?±?110 nm for 14 days and 673?±?171 nm for 30 days. Above results showed that PSS/MWNTs could be well stable in high salts solutions for a long period of time. After wrapped with PSS, the diameters of nanotubes changed from 30?~?40 to ~?430 nm, the thickness of wrapped polymer is about ~?400 nm by analysis of morphologies. The zeta potentials of PSS/MWNTs composites in various salinity of brines kept at approximately ??41?~???52 mV. Therefore, the well dispersion of PSS/MWNTs in high salinity is due to large negative charges of poly (sodium 4-styrenesulfonate), which provide enough electrostatic repulsion and steric repulsion to hinder compression of electric double layer caused by high concentration electrolytes.     

Synthesis and characterization of noscapine loaded magnetic polymeric nanoparticles

The delivery of noscapine therapies directly to the site of the tumor would ultimately allow higher concentrations of the drug to be delivered, and prolong circulation time in vivo to enhance the therapeutic outcome of this drug. Therefore, we sought to design magnetic based polymeric nanoparticles for the site directed delivery of noscapine to invasive tumors. We synthesized Fe₃O₄ nanoparticles with an average size of 10±2.5 nm. These Fe₃O₄ NPs were used to prepare noscapine loaded magnetic polymeric nanoparticles (NMNP) with an average size of 252±6.3 nm. Fourier transform infrared (FT-IR) spectroscopy showed the encapsulation of noscapine on the surface of the polymer matrix. The encapsulation of the Fe₃O₄ NPs on the surface of the polymer was confirmed by elemental analysis. We studied the drug loading efficiency of polylactide acid (PLLA) and poly (l-lactide acid-co-gylocolide) (PLGA) polymeric systems of various molecular weights. Our findings revealed that the molecular weight of the polymer plays a crucial role in the capacity of the drug loading on the polymer surface. Using a constant amount of polymer and Fe₃O₄ NPs, both PLLA and PLGA at lower molecule weights showed higher loading efficiencies for the drug on their surfaces.     

Bottom-up processing of thermoelectric nanocomposites from colloidal nanocrystal building blocks: the case of Ag2Te–PbTe

Nanoscale ZnO materials have been largely used in many products due to their distinct properties. However, ZnO nanoparticles (NPs) are hazardous to human health and the ecosystem. The characteristics and the stability of ZnO NPs are relevant to their fate in the environment and their potential toxicities. In this study, a stable commercial ZnO NP suspension was chosen to investigate its aggregation under various salt additions. Different concentrations of NaCl, KCl and CaCl₂ were chosen to represent various environmental conditions. Under pH 8?C9, the surface charge of commercial ZnO NPs was negative. The behavior of the stabilized ZnO NPs in water was affected by ionic combinations and ionic strength; that is, divalent cations were more effective than monovalent ones in promoting aggregation formation. The attachment efficiencies of ZnO aggregates were calculated based upon the aggregation kinetics. The critical coagulation concentration values for this commercial ZnO NPs were higher than previous reported for ZnO NPs, indicating this ZnO NP could be stable in the aquatic environment and might have increased hazardous potentials. Based upon the Derjaguin?CLandau?CVerwey?COverbeek theory, interactions between ZnO NPs in the presence of different ions were evaluated to illustrate the aggregation mechanism. Our results indicated that critical ionic type and concentration promote the aggregation of stable ZnO NPs. These understandings also can facilitate the design of the precipitation treatment to remove NPs from water.     

Photo- and cathodoluminescence of the cetylpyridinium chloride: ZnO nanocomposites

The cathodoluminescence and photoluminescence (PL) spectra of ZnO nanoparticles (NPs) embedded into the cetylpyridinium chloride (CPCL) matrix were studied. The composites were obtained by drying an aqueous suspension of CPCL and ZnO NPs, with NaCl and with NaOH additives. We observed that only NaOH addition lead to a significant increase in the PL intensity which we attribute to the surface chemistry of the ZnO NPs. We propose that thin ZnOH₂ and Na₂ZnO₂ layers form on the surface of the NPs; these layers present an increased number of oxygen vacancies, which act as emitting centres.     

Effect of bi-layer ratio in ZnO/Al2O3 multilayers on microstructure and functional properties of ZnO nanocrystals embedded in Al2O3 matrix

Zinc oxide (ZnO) nanocrystals (NCs) embedded in alumina (Al₂O₃) matrix were produced via rapid thermal annealing (RTA) of pulsed laser deposited ZnO/Al₂O₃ multilayered nanostructures. The effect of the thickness ratio (R) between Al₂O₃ and ZnO in one bi-layer on the microstructure and functional properties of NCs has been investigated. Grazing incidence small angle X-ray scattering confirmed the formation of nanocrystals after RTA. Grazing incidence wide angle X-ray scattering studies revealed that ZnO NCs have a high crystalline quality with (100) as preferred orientation. Tensile strain of NCs decreases with increasing R and is correlated to the distribution of NCs. From Raman analysis, it is noticed that the phonon frequency of the E₂ mode, related to the ZnO wurtzite phase, in NCs is shifted towards that of bulk ZnO with increasing R. Photoluminescence studies revealed that the near edge peak position shifts from 382 nm to 371 nm as the ratio R changes from 1.5 to 4 and is attributed to the strain effect. The intensity of emission in the yellow–green region due to defects decreases significantly with increasing R. Current–voltage (I–V) characteristics of Al/ZnO NCs embedded in Al₂O₃/n-Si (100)/Al have shown a hysteresis behavior. The increasing width of the hysteresis with increasing R revealed that the origin of the hysteresis might be due to the existence of polar surface charges on well-separated NCs. The high-resistance and low-resistance states in I–V hysteresis curves seem to be governed by Fowler–Nordheim tunneling and Schottky emission mechanisms, respectively.     

Clustering of Iron Oxide Nanoparticles with Amphiphilic Invertible Polymer Enhances Uptake and Release of Drugs and MRI Properties

A functionalization of iron oxide nanoparticles (NPs) of different diameters by the amphiphilic invertible polymer, (PEG600‐alt‐PTHF650)_k (PEG and PTHF stand for poly(ethylene glycol) and poly(tetrahydrofuran), respectively), leads to different NP/polymer architectures for dye/drug uptake and release, as is reported here for the first time. It is demonstrated that 18.6 ± 1.4 and 11.9 ± 0.6 nm NPs are individually coated by this polymer, while 5.9 ± 0.6 nm NPs form nanoparticle clusters (NPCs) which could be isolated by either ultracentrifugation or magnetic separation. This phenomenon is most likely due to the character of the (PEG600‐alt‐PTHF650)_k macromolecule with alternating hydrophilic and hydrophobic fragments and its dimensions sufficient to cause NP clustering. Utilizing Rhodamine B base (RBB) and doxorubicin (DOX), the data on uptake upon mixing and further release via inversion into octanol (mimicking the penetration of the cell biomembrane) are presented. The magnetic NPCs display enhanced uptake and release of both RBB and DOX most likely due to the higher retained polymer amount. The NPCs also display exceptional magnetic resonance imaging properties. This and the high uptake/release efficiency of the NPCs combined with easy magnetic separation make them promising for theranostic probes for magnetically targeted drug delivery.     

Imparting superhydrophobic and biocidal functionalities to a polymeric substrate by the sonochemical method

Multifunctional substrates with superhydrophobic and biocidal properties are gaining interest for a wide range of applications; however, the production of such surfaces remains challenging. Here, the sonochemical method is utilized to impart superhydrophobicity and antimicrobial properties to a polyethylene (PE) sheet. This is achieved by sonochemically depositing nanoparticles (NPs) of a hydrophobic fluoro-polymer (FP) on the PE sheets. The polymer is a flexible, transparent fluoroplastic composed of tetrafluoroethylene, hexafluoropropylene and vinylidene fluoride in the form of a powder. The NPs of polymers are generated and deposited on the surface of the PE using ultrasound irradiation. Optimizing the process results in a homogeneous distribution of 110–200 nm of NPs on the PE surface. The coated surface displays a water-contact angle of 160°, indicating excellent superhydrophobicity. This superhydrophobic surface shows high stability under outdoor conditions for two months, which is essential for various applications. In addition, metal-oxide nanoparticles (CuO or ZnO NPs) were integrated into the polymer coating to achieve antibacterial properties and increase the surface roughness. The metal oxides were also deposited sonochemically. The antibacterial activity of the FP@ZnO and FP@CuO PE composites was tested against the bacterium Staphylococcus aureus, and the results show that the FP@CuO PE can effectively eradicate the bacteria. This study highlights the feasibility of using the sonochemical method to deposit two separate functions, opening up new possibilities for producing “smart” novel surfaces.     

Preparation of n-ZnO/p-Si solar cells by oxidation of zinc nanoparticles: effect of oxidation temperature on the photovoltaic properties

In this study, n-ZnO/p-Si solar cells were fabricated by spraying ZnO nanoparticles (NPs) film synthesised by dissolving of high purity zinc in hydrogen peroxide H₂O₂ followed by thermal oxidation in air on p-type silicon substrates. The oxidation was carried out at different temperatures (200–500) °C. The crystalline structure of the ZnO NPs films was investigated by X-ray diffraction which indicated wurtzite structure films along (100) plane. The morphology of the NPs was studied by atomic force microscopy and scanning electron microscopy. The result showed an average grain size of ZnO NPs in the range of (72.7–95.8) nm and the surface roughness increasing with oxidation temperature. Three peaks located at ultraviolet, violet and green emission regions were noticed in the photoluminescence spectra of ZnO NPs. From optical studies, it was shown that the direct optical band gap is found to be in the range of (3.85–3.96) eV depended on the oxidation temperature. The synthesised ZnO films have n-type conductivity, and the mobility was in the range of (7–24) cm² V^?1 s^?1. Current–voltage I–V and capacitance–voltage C–V of ZnO NPs/Si heterojunction solar cell were investigated as function of oxidation temperature. The spectral response of n-ZnO NPs/p-Si solar cell showed two peaks of response and its maximum value approaching 0.62 mA W^?1 at λ = 800 nm. Solar cell oxidized at 500 °C gave open circuit voltage V _OC of 375 mV, short circuit current density J _SC of 25 mA cm^?2, a fill factor FF of 0.72, and conversion efficiency η of 6.79 % under illumination of 100 mW cm^?2.     

Dye-sensitized solar cells based on ZnO nanowire array/TiO2 nanoparticle composite photoelectrodes with controllable nanowire aspect ratio

The ZnO nanowire (NW) array/TiO₂ nanoparticle (NP) composite photoelectrode with controllable NW aspect ratio has been grown from aqueous solutions for the fabrication of dye-sensitized solar cells (DSSCs), which combines the advantages of the rapid electron transport in ZnO NW array and the high surface area of TiO₂ NPs. The results indicate that the composite photoelectrode achieves higher overall photoelectrical conversion efficiency (η) than the ZnO NW alone. As a result, DSSCs based on the ZnO NW array/TiO₂ NP composite photoelectrodes get the enhanced photoelectrical conversion efficiency, and the highest η is also achieved by rational tuning the aspect ratio of ZnO NWs. With the proper aspect ratio (ca. 6) of ZnO NW, the ZnO NW array/TiO₂ NP composite DSSC exhibits the highest conversion efficiency (5.5 %). It is elucidated by the dye adsorption amount and interfacial electron transport of DSSCs with the ZnO NW array/TiO₂ NP composite photoelectrode, which is quantitatively characterized using the UV-Vis absorption spectra and electrochemical impedance spectra. It is evident that the DSSC with the proper aspect ratio of ZnO NW displays the high dye adsorption amount and fastest interfacial electron transfer.     

On the spectral difference between electroluminescence and photoluminescence of Si nanocrystals: a mechanism study of electroluminescence

A highly dense and uniform layer of Au nanoparticles (NPs) on poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) film has been produced by the pulsed laser deposition (PLD) technique toward the production of an improved efficiency photovoltaic device. The advantage of PLD over other techniques is the easy and precise control of the Au NPs size and spatial distribution, without needing of further NP surface functionalization. The efficiency enhancement factor related to Au NPs doping has been evaluated in a solar cell based on poly-(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) diffused bilayer. The short-circuit current density, J _SC, increases by 18 % and the power conversion efficiency by 22 %, respectively, in comparison with an equivalent device without Au NPs. The optical and morphological properties of the Au NPs layer have been selected in order to evaluate the contribution of the surface plasmon resonance as enhancement factor of the solar cell efficiency, in a range size where light scattering is negligible.     

Electrostatic self-assembly of Fe3O4 nanoparticles on carbon nanotubes

Carbon nanotubes (CNTs)-based magnetic nanocomposites can find numerous applications in nanotechnology, integrated functional system, and in medicine owing to their great potentialities. Herein, densely distributed magnetic Fe₃O₄ nanoparticles were successfully attached onto the convex surfaces of carbon nanotubes (CNTs) by an in situ polyol-medium solvothermal method via non-covalent functionalization of CNTs with cationic surfactant, cetyltrimethylammonium bromide (CTAB), and anionic polyelectrolyte, poly(sodium 4-styrenesulfonate) (PSS), through the polymer-wrapping technique, in which the negatively charged PSS-grafted CNTs can be used as primer for efficiently adsorption of positively metal ions on the basis of electrostatic attraction. X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) analysis have been used to study the formation of Fe₃O₄/CNTs. The Fe₃O₄/CNTs nanocomposites were proved to be superparamagnetic with saturation magnetization of 43.5 emu g^?1. A mechanism scheme was proposed to illustrate the formation process of the magnetic nanocomposites.     

Polymer adsorption on the surface of highly dispersed silica

Attempts at modification of silica surface with a polymer (natural latex) directly in the course of the precipitation process have been made. The effects of temperature, non-ionic surfactants and silane coupling agent in preparation of poly[cis-isoprene]-coated silica on the precipitation of polymer/silica composites initiated by ammonium salts (NH₄Cl, (NH₄)₂SO₄, NH₄HCO₃), have been studied. The influence of the process parameters on the quality of the silicas obtained and the character of the polymer adsorption on the silica surface has been determined along with the effect of the surface impregnation with natural latex on physicochemical parameters of the silicas (bulk density, capacities to absorb water, dibutyl phthalate and paraffin oil) and their surface structure.     

Local structure of polymeric ferrogels

We synthesize hybrid gels incorporating γ‐Fe₂O₃ nanoparticles (NPs), citrate coated, in a polyacrylamide (PAM) network. The local organisation and the rotational degrees of magnetic nanoparticles are probed in the conditions of gel synthesis and also at swelling equilibrium, to correlate the homogeneous/inhomogeneous structure of the ferrogels to the synthesis parameters and to their macroscopic elasticity. NP adsorption on the PAM network at low citrate concentration is responsible for the reinforcing of the polymer structure. At higher citrate concentration, due to a competition between citrate and NPs, the nanoparticles desorb from the polymer structure weakening the system.     

Plasmonic enhancement of optical absorption of UV radiation by Au nanoparticles dispersed on ZnO thin film

Ultraviolet photoconductivity in sol gel-derived ZnO thin film loaded with gold (Au) nanoparticle (NPs) is investigated. Au-NPs loaded ZnO thin film (Au-NPs/ZnO) is found to exhibit high photoconducting gain (K) of about 4.12 × 10³ as compared to the bare ZnO thin film-based photodetector (4.9 × 10¹). The enhanced photoconductive gain of Au-NPs/ZnO detector has been achieved due to simultaneous lowering of dark current which occurs due to Schottky barrier effect originated after dispersing the Au NPs on the surface of ZnO thin film. The enhancement in photocurrent upon UV illumination is due to trapping of UV radiation via plasmonic effect caused by Au-NPs and subsequently coupling of absorbed light with the optical modes of underlying semiconducting ZnO surface.     

Electron paramagnetic resonance and optical absorption studies of manganese ions doped in polyvinyl(alcohol) complexed with polyethylene glycol polymer films

Electron paramagnetic resonance (EPR), optical absorption, and infrared spectral studies have been carried out on Mn²⁺ ions doped in poly(vinyl alcohol) (PVA) complexed with polyethylene glycol (PEG) films prepared by solution cast technique. The EPR spectra of 0.25?mol% Mn²⁺ ions doped polymer complex (PVA+PEG) at room temperature exhibit sextet hyperfine structure (hfs), centered at g????1.99. The spin?CHamiltonian parameter values indicate that the ground state of Mn²⁺ ion is d⁵ and the site symmetry around Mn²⁺ ions in tetragonally distorted octahedral site. The spin concentration participating in the resonance is measured as a function of temperature and it is observed that it obeys Boltzmann??s law. The paramagnetic susceptibility (??) is calculated from the EPR data at various temperatures (93?C333?K) and it obeys the Curie?CWeiss law. The optical absorption spectra exhibits two bands which are assigned to ⁶A_1g (S)??⁴A_1g (G) or ⁴E_g (G) and ⁶A_1g (S)??⁴T_2g (G) transitions. The infrared spectrum exhibits few bands due to the presence of O?CH, C?CH, and C=C groups.     

Encapsulation of a proteasome inhibitor with gold-polysaccharide nanocarriers

Groundwater remediation using iron oxide and zero-valent iron nanoparticles (NPs) can be effective, but is limited in many applications due to the NP strong retention in groundwater-saturated porous media after injection, the passivation of the porous surface, and the high cost of nanomaterials versus macro scale iron. In this study, we investigated transport of bare and polymer-coated 2-line ferrihydrite NPs (30–300 nm) in saturated aquifer sediments. The influence of poly(acrylic acid) (PAA) polymer coatings was studied on the colloidal stability and transport in sediments packed column tests simulating groundwater flow in saturated sediments. In addition, the influence of calcium cations was investigated by transport measurements using sediments with calcium concentrations in the aqueous phase ranging from 0.5 (typical for most sediments) to 2 mM. Measurements were also made of zeta potential, hydrodynamic diameter, polymer adsorption and desorption properties, and bio-availability of PAA-coated NPs. We found that NP transport through the saturated aquifer sediments was improved by PAA coating and that the transport properties could be tuned by adjusting the polymer concentration. We further discovered that PAA coatings enhanced NP transport, compared to bare NPs, in all calcium-containing experiments tested, however, the presence of calcium always exhibited a negative effect on NP transport. In tests of bioavailability, the iron reduction rate of the coated and bare NPs by Geobacter sulfurreducens was the same, which shows that the PAA coating does not significantly reduce NP Fe(III) bioavailability. Our results demonstrate that much improved transport of iron oxide NP can be achieved in saturated aquifer sediments by introducing negatively charged polyelectrolytes and optimizing polymer concentrations, and furthermore, these coated NPs retain their bioavailability that is needed for applications in bio-environmental remediation.     

The Toxicity of Silver Nanoparticles Depends on Their Uptake by Cells and Thus on Their Surface Chemistry

A set of three types of silver nanoparticles (Ag NPs) are prepared, which have the same Ag cores, but different surface chemistry. Ag cores are stabilized with mercaptoundecanoic acid (MUA) or with a polymer shell [poly(isobutylene‐alt‐maleic anhydride) (PMA)]. In order to reduce cellular uptake, the polymer‐coated Ag NPs are additionally modified with polyethylene glycol (PEG). Corrosion (oxidation) of the NPs is quantified and their colloidal stability is investigated. MUA‐coated NPs have a much lower colloidal stability than PMA‐coated NPs and are largely agglomerated. All Ag NPs corrode faster in an acidic environment and thus more Ag(I) ions are released inside endosomal/lysosomal compartments. PMA coating does not reduce leaching of Ag(I) ions compared with MUA coating. PEGylation reduces NP cellular uptake and also the toxicity. PMA‐coated NPs have reduced toxicity compared with MUA‐coated NPs. All studied Ag NPs were less toxic than free Ag(I) ions. All in all, the cytotoxicity of Ag NPs is correlated on their uptake by cells and agglomeration behavior.     

水热法促进EuVO_4@YVO_4核壳结构纳米颗粒中Eu~(3+)的扩散及其对发光性能的影响

采用共沉淀法制备了EuVO4@YVO4核壳结构纳米颗粒,然后用聚电解质聚苯乙烯磺酸钠对其进行包覆和保护,并在200?C下对样品水热处理0—48 h.在水热处理48 h后,样品的发光强度增强了约5倍,平均发光寿命由0.410 ms延长至0.579 ms.对样品的发光衰减曲线的拟合、分析为Eu3+的扩散提供了有力的证据.这种自内而外的扩散降低了样品核心中Eu3+的局域浓度,削弱了浓度猝灭效应,同时又能够避免表面猝灭效应的发生,从而使得样品的发光寿命变长、发光效率迅速提升.     

Electrochemical characterization of ionic liquid based gel polymer electrolyte for lithium battery application

High molecular weight polymer poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP), ionic liquid 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide (EMIMFSI), and salt lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-based free-standing and conducting ionic liquid-based gel polymer electrolytes (ILGPE) have been prepared by solution cast method. Thermal, electrical, and electrochemical properties of 80 wt% IL containing gel polymer electrolyte (GPE) are investigated by thermogravimetric (TGA), impedance spectroscopy, linear sweep voltammetry (LSV), and cyclic voltammetry (CV). The 80 wt% IL containing GPE shows good thermal stability (~?200 °C), ionic conductivity (6.42?×?10^?4 S cm^?1), lithium ion conductivity (1.40?×?10^?4 S cm^?1 at 30 °C), and wide electrochemical stability window (~?4.10 V versus Li/Li⁺ at 30 °C). Furthermore, the surface of LiFePO₄ cathode material was modified by graphene oxide, with smooth and uniform coating layer, as confirmed by scanning electron microscopy (SEM), and with element content, as confirmed by energy dispersive X-ray (EDX) spectrum. The graphene oxide-coated LiFePO₄ cathode shows improved electrochemical performance with a good charge-discharge capacity and cyclic stability up to 50 cycles at 1C rate, as compared with the without coated LiFePO₄. At 30 °C, the discharge capacity reaches a maximum value of 104.50 and 95.0 mAh g^?1 for graphene oxide-coated LiFePO₄ and without coated LiFePO₄ at 1C rate respectively. These results indicated improved electrochemical performance of pristine LiFePO₄ cathode after coating with graphene oxide.