Determination of boron in water and pharmaceuticals by sequential-injection analysis and fluorimetric detection

This work reports the application of a sequential-injection analysis (SIA) method for the determination of boron. The method relies on the enhancement of the fluorescence (λ_ex=313 nm, λ_em=360 nm) of chromotropic acid (4,5-dihydroxynaphthalene-2,7-disulphonic acid-CA) as a result of its complexation with boric acid (BA). Individual zones of the sample, the CA solution in a suitable buffer and a NaOH solution were aspirated in the holding coil of the SIA apparatus. As the zones were propelled towards the detector, zone penetration in the sample–CA interfaces occurred resulting in the formation of the strongly fluorescent BA–CA complex. The native fluorescence of the CA was quenched by the alkaline environment established as a result of the mixing at the CA–NaOH interface. The chemical and instrumental parameters affecting the fluorescence intensity were investigated and the influence of potential interferents was investigated. After selecting the most suitable conditions, the calibration plot for boron was linear in the range of 8–350 μg l⁻¹ with a 3σ limit of detection of 3 μg l⁻¹ and a relative standard deviation of 2.7% at the 90 μg l⁻¹ boron level (n=8). Finally, the method was applied to the determination of boron in natural waters and pharmaceutical products with revoveries in the range of 96–106%.     

Determination of nanomolar concentrations of phosphate in freshwaters using flow injection with luminol chemiluminescence detection

A simple and rapid flow injection (FI) method is reported for the determination of phosphate (as molybdate reactive P) in freshwaters based on luminol chemiluminescence (CL) detection. The molybdophosphoric heteropoly acid formed by phosphate and ammonium molybdate in acidic conditions generated chemiluminescence emission via the oxidation of luminol. The detection limit (3× standard deviation of blank) was 0.03 μg P l⁻¹ (1.0 nM), with a sample throughput of 180 h⁻¹. The calibration graph was linear over the range 0.032–3.26 μg P l⁻¹ (r²=0.9880) with relative standard deviations (n=4) in the range 1.2–4.7%. Interfering cations (Ca(II), Mg(II), Ni(II), Zn(II), Cu(II), Co(II), Fe(II) and Fe(III)) were removed by passing the sample through an in-line iminodiacetate chelating column. Silicate interference (at 5 mg Si l⁻¹) was effectively masked by the addition of tartaric acid and other common anions (Cl⁻, SO₄²⁻, HCO₃⁻, NO₃⁻ and NO₂⁻) did not interfere at their maximum admissible concentrations in freshwaters. The method was applied to freshwater samples and the results (26.1±1.1–62.0±0.4 μg P l⁻¹) were not significantly different (P=0.05) from results obtained using a segmented flow analyser method with spectrophotometric detection (24.4±4.45–84.0±16.0 μg P l⁻¹).     

Determination of rhodamine 123 by sequential injection technique for pharmacokinetic studies in the rat placenta

The sequential injection (SIA) technique was applied in pharmacokinetic studies of the transporter-mediated passage of a model substrate, rhodamine 123 (Rho123), through the dually perfused rat term placenta. The method described was used for real-time monitoring of Rho123 concentrations in both the maternal and fetal compartments. Determination was processed by fluorescence detection (λ_ex=480 nm, λ_em580 nm); calibration curve was linear over the range 0.01–50 μmol l⁻¹ (r=0.99965), detection limit was 10 nmol l⁻¹ (3σ) and RSD2% (10 readings). Transport of Rho123 was scanned under various conditions (ATP-synthesis inhibition) and several inhibitors of P-glycoprotein transporter were tested (e.g. quinidine). The advantages of the modern SIA method—an automated analytical tool providing both fast and precise analysis—were successfully demonstrated for examination of transport profiles to investigate the effect of P-glycoprotein on the placental transfer of Rho123.     

Determination of aluminium and manganese in human scalp hair by electrothermal atomic absorption spectrometry using slurry sampling

Methods for the determination of aluminium and manganese in human scalp hair samples by electrothermal atomic absorption spectrometry using the slurry sampling technique were developed. Palladium and magnesium nitrate were used as chemical modifiers. Hair samples were pulverized using a zirconia vibrational mill ball, and were prepared as aqueous slurries. Determinations can be performed in the linear ranges of 1.9–150 μg l⁻¹ Al³⁺ and 0.03–10.0 μg l⁻¹ Mn²⁺. Limits of detection of 0.9 mg kg⁻¹ and 27.6 μg kg⁻¹ were obtained for aluminium and manganese, respectively. The analytical recoveries were between 99.6 and 101.8% for aluminium and in the 98.3–101.3% range for manganese. The repeatability of the methods (n=11), slurry preparation procedure and ETAAS measurement, was 16.0 and 7.9% for aluminium and manganese, respectively. The methods were finally applied to the aluminium and manganese determination in 25 scalp hair samples from healthy adults. The levels for aluminium were between 8.21 and 74.08 mg kg⁻¹, while concentrations between 0.03 and 1.20 mg kg⁻¹ were found for manganese.     

Flow injection determination of bismuth in urine by successive retention of Bi(III) and tetrahydroborate(III) on an anion-exchange resin and hydride generation atomic absorption spectrometry

Bismuth as BiCl₄⁻ and BH₄⁻ ware successively retained in a column (150 mm × 4 mm, length × i.d.) packed with Amberlite IRA-410 (strong anion-exchange resin). This was followed by passage of an injected slug of hydrochloric acid resulting in bismuthine generation (BiH₃). BiH₃ was stripped from the eluent solution by the addition of a nitrogen flow and the bulk phases were separated in a gas–liquid separator. Finally, bismutine was atomized in a quartz tube for the subsequent detection of bismuth by atomic absorption spectrometry. Different halide complexes of bismuth (namely, BiBr₄⁻, BiI₄⁻ and BiCl₄⁻) were tested for its pre-concentration, being the chloride complexes which produced the best results. Therefore, a concentration of 0.3 mol l⁻¹ of HCl was added to the samples and calibration solutions. A linear response was obtained between the detection limit (3σ) of 0.225 and 80 μg l⁻¹. The R.S.D.% (n = 10) for a solution containing 50 μg l⁻¹ of Bi was 0.85%. The tolerance of the system to interferences was evaluated by investigating the effect of the following ions: Cu²⁺, Co²⁺, Ni²⁺, Fe³⁺, Cd²⁺, Pb²⁺, Hg²⁺, Zn²⁺, and Mg²⁺. The most severe depression was caused by Hg²⁺, which at 60 mg l⁻¹ caused a 5% depression on the signal. For the other cations, concentrations between 1000 and 10,000 mg l⁻¹ could be tolerated. The system was applied to the determination of Bi in urine of patients under therapy with bismuth subcitrate. The recovery of spikes of 5 and 50 μg l⁻¹ of Bi added to the samples prior to digestion with HNO₃ and H₂O₂ was in satisfactory ranges from 95.0 to 101.0%. The concentrations of bismuth found in six selected samples using this procedure were in good agreement with those obtained by an alternative technique (ETAAS). Finally, the concentration of Bi determined in urine before and after 3 days of treatment were 1.94 ± 1.26 and 9.02 ± 5.82 μg l⁻¹, respectively.     

Reverse flow injection spectrophotometric determination of iron(III) using norfloxacin

A reversed flow injection colorimetric procedure for determining iron(III) at the μg level was proposed. It is based on the reaction between iron(III) with norfloxacin (NRF) in 0.07 mol l⁻¹ ammonium sulfate solution, resulting in an intense yellow complex with a suitable absorption at 435 nm. Optimum conditions for determining iron(III) were investigated by univariate method. The method involved injection of a 150 μl of 0.04% w/v colorimetric reagent solution into a merged streams of sample and/or standard solution containing iron(III) and 0.07 mol l⁻¹ ammonium sulfate in sulfuric acid (pH 3.5) solution which was then passed through a single bead string reactor. Subsequently the absorbance as peak height was monitored at 435 nm. Beer's law obeyed over the range of 0.2–1.4 μg ml⁻¹ iron(III). The method has been applied to the determination of total iron in water samples digested with HNO₃–H₂O₂ (1:9 v/v). Detection limit (3σ) was 0.01 μg ml⁻¹ the sample through of 86 h⁻¹ and the coefficient of variation of 1.77% (n=12) for 1 μg ml⁻¹ Fe(III) were achieved with the recovery of the spiked Fe(III) of 92.6–99.8%.     

A piezoelectric quartz crystal sensor array self assembled calixarene bilayers for detection of volatile organic amine in gas

P-tert-butylcalix[n]arenes (n=4, 6, 8, abbreviated as CA[4], CA[6], CA[8], respectively) were immobilized on the Au surface of the piezoelectric quartz crystal by the reaction between CA[n] and the acid chloride terminated mercaptoacetic acid (MAA) self assembled monolayers to form MAA/CA[n] bilayers. The sensing films were not only immobilized easily and reproducibly, but also used to improve the reversibility of the sensor signal. The response characteristics show the response of CA to organic amine attributes to specific interaction between CA[n] (host) and organic amines (guest). The frequency shifts of n-butylamine and iso-butylamine are much larger than tert-butylamine and diethylamine because of shape-selection and hydrogen bonding. Compared to CA[6] and CA[4], CA[8] has highest sensitivity to organic amine due to having more flexibility to accommodate guest molecules. A sensor array with three-layer back-propagation neural network was applied to detect the binary mixture of n-butylamine in the range of 7.14–142 μl l⁻¹ and iso-butylamine in the range of 7.14–57 μl l⁻¹. The optimum values of learning rate (0.15) and momentum term (0.8) were determined by experiment. The best epoch of training was 1098. The root mean square error of prediction was 1.69 (μl l⁻¹) for n-butylamine, and 1.42 (μl l⁻¹) for iso-butylamine.     

An on-line flow-injection microwave-assisted mineralization and a precipitation/dissolution system for the determination of molybdenum in blood serum and whole blood by electrothermal atomic absorption spectrometry

An on-line flow injection (FI) precipitation–dissolution system with microwave-assisted sample digestion has been developed for the electrothermal atomic absorption spectrometry (ETAAS) determination of trace or ultratrace amounts of molybdenum in human blood serum and whole blood samples. After the exposure of the sample to microwave radiation, the on-line precipitation of molybdenum was achieved by the merging-zone of a 0.5-ml plug of sample with a plug of potassium ferrocyanide, which were carried downstream with a solution of 0.5 mol l⁻¹ of HNO₃. The interfering effects of iron and copper were minimized by the introduction of a flow of a 5% (w/v) sodium potassium tartrate (for iron) and 2% (w/v) of thiourea (for copper and zinc) in a 5% (v/v) ammonia and 2% (v/v) ammonium chloride solution previous to the precipitation reaction. The reddish-brown precipitate of molybdenyl ferrocyanide was collected on the walls of a knotted reactor. The precipitate was dissolved with the introduction of 1 ml of a 3.0 mol l⁻¹ NaOH solution and the best performance in terms of detection limit and precision was achieved when a sub-sample of 140 μl was collected in a capillary of a sampling arm assembly, to introduce 20 μl volumes into the atomizer by means of positive displacement with air through a time-based injector. A detection limit (3σ) of 0.1 μg Mo l⁻¹ using an aqueous standard solution was obtained. The method is quantitative and is applied over the range 0.2–20.0 μg Mo l⁻¹. The precision of the method evaluated by ten replicate analyses of aqueous standard solutions containing 0.5 and 1.0 μg Mo l⁻¹ was 2.8 and 3.1% (relative standard deviation, RSD) (for n=5), respectively. Whereas, the precision evaluated by five replicate analysis of a serum and a whole blood sample were 3.3 and 3.8% RSD. An enrichment factor of ca. 3.5 was achieved with the introduction of 0.5 ml aqueous standard solutions at a sample flow rate of 1.0 ml min⁻¹. Recoveries of spiked molybdenum in blood serum and whole blood were in the ranges 96–102 and 94–98%, respectively. The results obtained for two human whole blood certified reference materials were in good agreement with the indicative values.     

Determination of glyphosate by ion chromatography

An ion chromatography system for the determination of glyphosate was described. Ion chromatograph was carried out by suppressed conductivity detection (DX-100). The eluent contained 9 mmol l⁻¹ Na₂CO₃ and 4 mmol l⁻¹ NaOH. The detection limit was 0.042 μg ml⁻¹ (S/N=3). The relative standard deviation was 1.99% and the correlation coefficient of the calibration curve for area was 0.9995. The linear range was 0.042100 μg ml⁻¹. Common inorganic ion and organic acids did not interfere. The recovery was 96.4103.2%. The method was simple, rapid, reliable and inexpensive.     

Development of a luminol-based chemiluminescence flow-injection method for the determination of dichlorvos pesticide

A simple, fast chemiluminescence (CL) flow-injection method based on the reaction of luminol with H₂O₂ in the presence of a cationic surfactant (cyltrimethylammonium bromide, CTMAB) has been described for the direct determination of dichlorvos pesticide (DDVP). Under the optimal conditions, the CL intensity was linear to the DDVP concentration in the range of 0.02–3.1 μg ml⁻¹ (r=0.9998, n=10). The relative standard deviation was 3.4% at 0.35 μg ml⁻¹ (n=10), with a detection limit (3σ) of 0.008 μg ml⁻¹ DDVP. The possible reaction mechanism was also discussed. This method has been successfully applied to the determination of trace DDVP residue in vegetable sample and results have been compared with that of the UV method.     

Analysis of acrylamide in coffee and dietary exposure to acrylamide from coffee

An analytical method for analysing acrylamide in coffee was validated. The analysis of prepared coffee includes a comprehensive clean-up using multimode solid-phase extraction (SPE) by automatic SPE equipment and detection by liquid chromatography tandem mass spectrometry using electrospray in the positive mode. The recoveries of acrylamide in ready-to-drink coffee spiked with 5 and 10 μg l⁻¹ were 96±14% and 100±8%, respectively. Within laboratory reproducibility for the same spiking levels were 14% and 9%, respectively. Coffee samples (n = 25) prepared twice by coffee machines and twice by a French Press Cafetière coffee maker contained 8±3 μg l⁻¹ and 9±3 μg l⁻¹ acrylamide. Five ready-to-drink instant coffee prepared twice contained 8±2 μg l⁻¹. Hence, the results do not show significant differences in the acrylamide contents in ready-to-drink coffee prepared by coffee machine, French Press or from instant coffee. Medium roasted coffee contained more acrylamide (10 μg l⁻¹) than dark roasted coffee (5 μg l⁻¹). Males aged 35–45 years, drinking on average 1.1 l coffee per day are exposed to the highest doses of acrylamide from coffee. The dietary intake of acrylamide from coffee comprises, on an average, 10 μg day⁻¹ for males and 9 μg day⁻¹ for females aged 35–45 years. Probabilistic modelling of the exposure of Danish consumers (all adults) to acrylamide from coffee shows a mean exposure of 6.5 μg day⁻¹ and a 95 percentile of 18 μg day⁻¹.     

Determination of physiological noble metals in human urine using liquid-liquid extraction and Zeeman electrothermal atomic absorption spectrometry

An extremely sensitive, reliable and simple procedure is described for the determination of physiological palladium, platinum and gold in human urine. The urine samples were adjusted to pH 4 (Pd, Au) or pH 5 (Pt), followed by conversion of the analytes to their pyrrolidinedithiocarbamate complexes. These complexes were separated from the matrix by liquid-liquid extraction into 4-methyl-2-pentanone resulting in a 25-fold enrichment. Determination was by electrothermal atomic absorption spectrometry (ET-AAS) using longitudinal inverse alternating current Zeeman-effect background correction. The limits of detection calculated from three standard deviations of the blank values were 20 ng l⁻¹ for Pd and Au and 70 ng l⁻¹ Pt. Within-day precision (n = 10, 5 μg l⁻¹) ranged 5.2%–7.7%. The procedure is successfully applied to determine urinary palladium, platinum and gold in nine unexposed persons. Palladium levels in urine ranged < 20–80 ng l⁻¹ (arithmetical MEAN=38.7 ng l⁻¹), while gold levels ranged < 20–130 ng l⁻¹ (36.0 ng l⁻¹). Physiological platinum levels in urine were all < 70 ng l⁻¹. The accuracy of the procedure was checked by analyzing a series of urine samples by a second independent method (magnetic sector field inductively-coupled plasma-mass spectrometry) in combination with UV photolysis.     

Synthesis, structure, and fluorescence of two cadmium(II)-citrate coordination polymers with different coordination architectures

Two novel Cd(II)-citrate complexes were obtained with different metal/ligand ratios through hydrothermal method. Their structures were determined by single-crystal X-ray diffraction analysis. Although their topological structures are both 2-D layer network assemblies, both central Cd(II) ions and Hcit³⁻ ligands display completely different coordination modes. In polymeric complex 1, Hcit³⁻ serves as a μ₁₀-bridged and central Cd(II) ions adopt 6- and 8-coordinated configurations. In contrast, a μ₉-bridged and 6- and 7-coordinated environments between Cd(II) and Hcit³⁻ are established in the polymeric complex 2. Two Complexes remain stable up to approximately 300 °C. The complex 1 exhibits strong fluorescent emission band at 450 nm (λ=346 nm) as well as complex 2 exhibits strong fluorescent emission band at 430 (λ=346 nm).     

Biosensor for phenol based on the direct electron transfer blocking of peroxidase immobilising on silica–titanium

Horseradish peroxidase (HRP) was immobilised on silica gel modified with titanium oxide. This material was employed to prepare modified carbon paste electrode. The direct electron transfer of the hydrogen peroxide reduction by HRP was blocked when immobilised on silica–titanium. This biosensor presented a very sensitive response for phenol (1 μmol l⁻¹) at an applied potential of 0 mV vs SCE. The best condition was achieved in phosphate buffer pH 6.8, ratio of hydrogen peroxide/phenol higher than 0.35. The biosensor showed a linear response range between 10 and 50 μmol l⁻¹ of phenol, adjusted by the equation j=−32.8+16.3 [phenol], for n=5 with a correlation coefficient of 0.9995. The response time of the biosensor was about 3 s.     

Simultaneous determination of selenium and lead in whole blood samples by differential pulse polarography

The polarographic reduction of lead in the presence of selenite gives rise to an additional peak corresponding to the reduction of lead (Pb) on adsorbed selenium (Se) on mercury at −0.33 V. The selenium and lead content can be determined using this peak by the addition of a known amount of one of these ions first and then the second ion. The linear domain range of lead is 5.0×10⁻⁷–2.0×10⁻⁵ M and for selenium 5.0×10⁻⁷–1.0×10⁻⁵ M. Using this method 4.90×10⁻⁷ M Se(IV) and 1.47×10⁻⁶ M Pb(II) in a synthetic sample could be determined with a relative error of +2.0% and 1.8%, respectively (n=4). A recovery test after acid digestion for a synthetic sample was 97% for selenium and 96.5% for lead. The method was applied to 1 ml of digested blood, and 328±23 μg l⁻¹ Se(IV) and 850±62 μg l⁻¹ Pb(II) could be determined with a 90% (n=5) confidence interval.     

Cost-effective flow injection spectrophotometric assay of iron content in pharmaceutical preparations using salicylate reagent

A new flow injection procedure for an assay of Fe(III) by using salicylate obtained from antipyretic powder, which is a cheap and easily available reagent, is proposed. A red complex was continuously monitored by a laboratory-made green LED colorimeter. A linear calibration was obtained in the range of 1–20 mg Fe l⁻¹ with a detection limit of 0.5 mg Fe l⁻¹ and R.S.D.s of 1.4–5.4% (n=3, for 1–20 mg Fe l⁻¹). The new procedure was applied to assay iron contents in pharmaceutical preparations. The results were in good agreement with those of the USP standard method.     

On-line extraction-spectrophotometric determination of neostigmine in pharmaceuticals using double membrane phase separator and monovalent dyestuff

A simple, sensitive and rapid spectrophotometric method for the determination of neostigmine by flow injection analysis (FIA) coupled with an ion associate extraction has been developed. The three-line manifold was assembled. Neostigmine(200 μl) was injected into a distilled water stream and the pH was adjusted to 10 with a borate–phosphate buffer solution. Then, the stream was mixed with the ion-pairing tetrabromophenolphthalein ethylester (TBPEH)-1,2-dichloroethane solution. After phase separation with a double membrane phase separator, absorbance was measured at 610 nm. A linear calibration graph was obtained between 1×10⁻⁷ mol l⁻¹ and 5×10⁻⁷ mol l⁻¹ of neostigmine. Up to 48 samples h⁻¹ could be processed with a relative standard deviation (R.S.D.) of 0.5% (n=5) for 4×10⁻⁷ mol l⁻¹ neostigmine. The proposed system was applied to the simple, reproducible and rapid determination of neostigmine in commercial pharmaceuticals.     

A new flow-injection determination of glucose based on the redox reaction of hydroquinone with iron(III) in the presence of 1,10-phenanthroline

A new spectrophotometric flow-injection (FI) method is proposed for the determination of glucose based on the redox reaction of hydroquinone with iron(III). When a glucose solution containing quinone is passed through the immobilized glucose oxidase column introduced in FI system, quinone is reduced to hydroquinone by glucose. In the presence of 1,10-phenanthroline (phen), iron(III) is then quantitatively reduced by hydroquinone to iron(II) followed by the formation of iron(II)-phen complex (λ_max=510 nm). An FI peak observed at 510 nm corresponds to the concentration of glucose. The wide dynamic range for glucose was obtained in the range of 1×10⁻⁶–1×10⁻³ mol l⁻¹ at a sampling rate of 24 h⁻¹ and the detection limit (S/N=3) was 5×10⁻⁷ mol l⁻¹. Relative standard deviations were 0.78, 0.44 and 0.23% (n=5) for 5×10⁻⁶, 5×10⁻⁵ and 5×10⁻⁴ mol l⁻¹ of glucose, respectively. The proposed method was successfully applied to the determination of glucose in control blood sera, human blood plasma and wine.     

Continuous flow system for lead determination by faas in spirituous beverages with solid phase extraction and on-line copper removal

A continuous flow system for the determination of lead in home made spirituous beverages was developed. The determination was based on the formation of a neutral chelate of the element with ammonium pyrrolidine dithiocarbamate, its adsorption onto a minicolumn packed with sodium faujasite type Y synthetic zeolite, followed by elution with methyl isobutyl ketone and determination by flame atomic absorption spectrometry. Ethanol and copper interfere strongly in the determination and therefore, must be separated prior to the analysis. Copper is removed by precipitation with rubeanic acid, while ethanol is eliminated by rotaevaporation. Sample solutions containing Pb²⁺ in the concentration range from 5 to 120 μg l⁻¹ at pH 2.5 could be analyzed, by using a preconcentration time of 3 min. Preconcentration factors from 80 to 140 were achieved for a sample volume of 6 ml and the detection limit varied from 1.4 to 3.5 μg l⁻¹, depending on the matrix composition. The relative standard deviations for 60 μg l⁻¹ Pb was 3.2% (n = 10) and the recovery of spikes (20, 40, 60 and 80 μg l⁻¹) added to the samples was estimated within 92–105% range, suggesting that lead can be quantitatively determined in such samples. Determining lead in several samples by an alternative technique further checked the accuracy. Finally, the concentrations of Pb²⁺ determined in 28 samples of Venezuelan spirituous beverages were in 12.6–370.0 μg l⁻¹ range, depending on the fermenting material based on different mixtures of agave, raw sugar cane and white sugar.     

Spectrofluorimetric determination of levofloxacin in tablets, human urine and serum

A spectrofluorimetric method to determine levofloxacin is proposed and applied to determine the substance in tablets and spiked human urine and serum. The fluorimetric method allow the determination of 20–3000 ng ml⁻¹ of levofloxacin in aqueous solution containing acetic acid–sodium acetate buffer (pH 4) with λ_exc=292 and λ_em=494 nm, respectively. Micelle enhanced fluorescence improves the sensibility and allows levofloxacin direct measurement in spiked Human serum (5 μg ml⁻¹) and urine (420 μg ml⁻¹), in 8 mM sodium dodecyl sulphate solutions at pH 5.