Influence of ceramic process and Eu content on the composite multiferroic properties of the Ba6−2xLn2xFe1+xNb9−xO30 TTB system

The present work reports the optimisation of the composition and elaboration process of Ba_6−2xLn_2xFe_1+xNb_9−xO₃₀ (0.6 < x < 1.0), a composite multiferroic below 440 K. Both firing and sintering conditions have been investigated in order to lower the two spurious phases content and to improve the ceramic quality. The Eu content has also been varied, with subsequent adjustment of cationic content to maintain charge compensation and site occupancies. The evolution of phase content, dielectric and magnetic properties has been evaluated with respect to these parameters. It was found that optimal processing parameters allow a significant improvement of dielectric properties but leave magnetic properties unaffected. Eu content modification impacts both the dielectric and magnetic properties of the TTB samples and changes their dielectric behaviour from ferroelectric to relaxor.     

Structure and Magnetism of Pr1−xSrxFeO3−δ

Crystal structure, redox, and magnetic properties for the Pr_1−xSr_xFeO_3−δ solid-solution phase have been studied. Oxidized samples (prepared in air at 900°C) crystallize in the GdFeO₃-type structure for 0≤x≤0.80, and probably in the Sr₈Fe₈O₂₃-type (unpublished) structure for x=0.90. Reduced samples (containing virtually only Fe³⁺) crystallize as the perovskite aristotype for x=0.50 and 0.67 with randomly distributed vacancies. The Fe⁴⁺ content increases linearly in the oxidized samples up to x≈0.70, whereupon it stabilizes at around 55%. Antiferromagnetic ordering of the G type is observed for oxidized samples (0≤x≤0.90) which show decreasing Néel temperature and ordered magnetic moment with increasing x, while the Néel temperature is nearly constant at 700 K for reduced samples. Electronic transitions for iron from an average-valence state via charge-separated to disproportionated states are proposed from anomalies in magnetic susceptibility curves in the temperature ranges 500–600 K and 150–185 K.     

Pillaring of Layered Perovskites, K1−xLaxCa2−xNb3O10, with Nanosized Fe2O3 Particles

Nanosized Fe₂O₃ clusters are pillared in the interlayer spaces of layered perovskites, H_1−xLa_xCa_2−xNb₃O₁₀ (0≤x≤0.75) by a guest-exchange reaction using the trinuclear acetato-hydroxo iron cation, [Fe₃(OCOCH₃)₇ OH·2H₂O]⁺. The interlayer spaces of niobate layers are pre-expanded with n-butylammonium cations (n-C₄H₉NH⁺₃), which are subsequently replaced by bulky iron pillaring species to form Fe(III) complex intercalated layer niobates. Upon heating at 380°C, the interlayered acetato-hydroxo iron complexes are converted into Fe₂O₃ nanoclusters with a thickness of ca. 3.5 Å irrespective of the interlayer charge density (x). The band-gap energy of the Fe₂O₃ pillars (E_g2.25 eV) is slightly larger than that of bulk Fe₂O₃ (E_g2.20 eV) but is smaller than that expected for such a small-sized semiconductor, which can be assigned to the pancake-shaped Fe₂O₃ pillars of 3.5 Å in height with comparatively large lateral dimension. X-ray absorption spectroscopic measurements at the Fe K-edge are carried out in order to obtain structural information on the Fe₂O₃ pillars stabilized between the niobate layers. XANES analysis reveals that the interlayer FeO₆ octahedra have coordination environments similar to that of bulk α-Fe₂O₃, but noncentrosymmetric distortion of interlayered FeO₆ is enhanced due to the asymmetric electric potential exerted by the negatively charged niobate layers. Scanning electron microscopic observation and nitrogen adsorption–desorption isotherm measurement suggest that the pillared derivatives are nanoporous materials with the highest BET specific surface area of ca. 116 m²/g.     

单分散NixZn1-xFe2O4纳米颗粒的制备及其磁热效应

以乙酰丙酮金属盐为前驱体,三乙二醇为溶剂,采用多元醇法制备了镍锌不同配比的Ni_xZn_(1-x)Fe_2O_4(x=0,0.3,0.5,0.7和1.0)铁氧体,并通过X射线衍射仪(XRD),透射电子显微镜(TEM)和振动样品磁强计(VSM)等对样品的结构、形貌、磁性能和磁热性能进行了表征。结果表明:Ni_xZn_(1-x)Fe_2O_4铁氧体分散性较好,尺寸均一,形状近似球形,平均粒径为4~5 nm。Ni_xZn_(1-x)Fe_2O_4纳米颗粒在室温下表现出亚铁磁性,饱和磁化强度随着镍含量的增加先增大后减小,当x=0.5时达到最大值29.38 emu·g~(-1)。在382k Hz交变磁场作用下,Ni_(0.5)Zn_(0.5)Fe_2O_4铁氧体温度可升温至313 K,表现出较好的磁热性能。     

Synthesis and low temperature fluorination of the alkaline-earth palladates Ba2−xSrxPdO3 (x = 0–2)

Since the discovery of superconductivity in Sr₂CuO₂F_2+δ there has been an increased interest in ternary oxide-fluorides. Sr₂CuO₂F_2+δ is prepared via low temperature (T = 220 °C) reaction routes. Low temperature fluorination induces an interesting structural rearrangement in the parent compound Sr₂CuO₃, which is a one-dimensional material containing linear chains of vertex sharing CuO₄ squares along the crystallographic b axis. Upon fluorination, one oxide is substituted by two fluorides and Cu²⁺ becomes octahedrally coordinated by four oxides and two fluorides. The fluorinated compound Sr₂CuO₂F_2+δ displays the T-type structure (La₂CuO₄). Insertion of excess fluorine, δ, also takes place and this fluorine occupies interstitial sites in the T structure. Although the starting material Ca₂CuO₃ is isostructural to Sr₂CuO₃, Ca₂CuO₂F_2+δ displays the T′ (Nd₂CuO₄) structure due to the smaller radius of Ca²⁺ compared to that of Sr²⁺.

The alkaline-earth palladates with the general formula A₂PdO₃ (A = Ba, Sr) are isostructural with the A₂CuO₃(A = Ca, Sr) materials. We prepared the Ba_2−xSr_xPdO₃ (x = 0–2) series and performed low temperature fluorination, which led to the synthesis of the series Ba_2−xSr_xPdO₂F_2+δ (0 ≤ x ≤ 1.5). All the compounds in the Ba_2−xSr_xPdO₂F_2+δ series show T′ structure (Ca₂CuO₂F_2+δ). Similarities and differences with Sr₂CuO₂F_2+δ and Ca₂CuO₂F_2+δ will be discussed.     

Tl2Ba2−xSrxCuO6: A system exhibiting a compositionally controlled superconductor-metal transition

Strontium-substituted thallium cuprates of the type Tl₂Ba_2−xSr_xCuO₆ have been synthesized for various values of x. Single phases were obtained for x ≤ 1.2. The compounds crystallize in the tetragonal structure with space group I4/mmm as the parent Tl₂Ba₂CuO₆ oxide. Both a and c lattice parameter decrease with increase in x. T_c decreases gradually from 92 to 77 K (x = 0.8). Beyond x = 1.0 superconductivity is lost. The x = 1.2 comparison is metallic down to 4.2 K.     

Nanocrystalline ferrites NixZn1−xFe2O4: Influence of cation distribution on acidic and gas sensing properties

This work is devoted to a detailed analysis of the interconnection between composition, cation distribution and acidic properties of the surface of nanocrystalline ferrites Ni_xZn_1−xFe₂O₄ obtained by aerosol pyrolysis. The detailed analysis of the Mössbauer spectra allows us to determine the distribution of cations between tetrahedral and octahedral positions in spinel structure. Depending on samples composition, the tetrahedral positions can be occupied by only Fe³⁺ cations (inverse spinel, x≥0.4) or by Fe³⁺ and Zn²⁺ cations (mixed spinel, x=0, 0.2). Increasing the nickel concentration in the ferrite leads to decrease in the number of strong acid centers on the surface. It was found that the decrease in the contribution of strong surface acid sites leads to an increase in sensory sensitivity of the ferrite towards ammonia. For ethanol detection an inverse relationship between sensor signal and surface acidity was observed.     

Nowotny chimney ladder compounds in Nd1+EFe4−xCoxB4

Structural investigations on Nd_1+EFe_4−xCo_xB₄ show the presence of distinct new phases with multiplicative c axis extensions (ladder compounds) and limited homogeneous range. We also report on compoundsR_1+EFe₄B₄ (R = rare earth) for which several new representatives (e.g., with R = La and Lu) are described. The ladder compounds in both substitutional series appear related and a common sequence as a function of composition is suggested. As an example the first new ladder type Nd_1.06Fe_1.5Co_2.5B₄ to develop out of NdCo₄B₄ is similar to La_1.06Fe₄B₄ and the third namely Nd_1.09Fe₃CoB₄ resembles Pr_1.10Fe₄B₄.     

Thermal analysis and thermal expansion studies on high density YBa2−xLaxCu3O7−δ, 0x0.2

The compositions in the YBa_2−xLa_xCu₃O_7−δ (0x0.2) system were prepared by the solid state reaction, employing a novel high-temperature oxygen sintering route. The modified sintering route yields dense slab like microstructures with large grains. The decomposition (incongruent melting) temperature of the YBa₂Cu₃O_7−δ (Y-123) phase was found to shift to higher temperatures with increasing oxygen partial pressure and lanthanum content. Structure remained orthorhombic up to x=0.2 with a decrease in the orthorhombic strain ((b−a)/b). Iodometric titration indicated a systematic increase in the oxygen content with increasing lanthanum content. Thermo-gravimetric studies in various oxygen partial pressures revealed that the oxygen diffusion in to the YBa₂Cu₃O_7−δ (δ>0.5) lattice is an exothermic event and takes place at temperatures not less than 573 K. High-temperature thermal-expansion measurements in air indicated that the nonlinearity in thermal expansion behaviour was reduced by the substitution of lanthanum.     

Crystal chemistry, modulated structure, and electrical conductivity in the oxygen excess scheelite-based compounds La1−xThxNbO4+x/2 and LaNb1−xWxO4+x/2

For La_1−xTh_xNbO_4+x/2, three phases with broad homogeneity regions occur, for 0.075 ≤ x ≤ 0.37, 0.41 < x < 0.61, and 0.65 ≤ x ≤ 0.74. All are related to the scheelite structure type, with at least the first exhibiting an incommensurate structural modulation. An analogous structurally modulated phase was found for LaNb_1−xW_xO_4+x/2 for 0.11 ≤ x ≤ 0.22. Additional phases occur at La_0.2Th_0.8NbO_4.4 and LaNb_0.4W_0.6O_4.3. The electrical conductivity and the direction and wavelength of the structural modulation have been characterized for the La_1−xTh_xNbO_4+x/2 phase with 0.075 ≤ x ≤ 0.37.     

Pyrochlore phases in the system ZnOBi2O3Sb2O5: II. Crystal structures of Zn2Bi3.08Sb2.92O14+δ and Zn2+xBi2.96−(x−y)Sb3.04−yO14.04+δ

Rietveld refinement of combined X-ray and neutron diffraction data has, within errors, confirmed the stoichiometries of two, cubic pyrochlore phases in the ZnOBi₂O₃Sb₂O₅ system. Neither phase has the ‘ideal’ stoichiometry, Zn₂Bi₃Sb₃O₁₄. One phase, P₁, is a Zn-rich, Bi-deficient solid solution Zn_2+xBi_{2.96−(x−y)}Sb_3.04−yO_14.04+δ. The other, P₂, is a Bi-rich line phase, stoichiometry Zn₂Bi_3.08Sb_2.92O_14+δ. Both structures have a mixture of Bi, Zn on the A-sites and Zn, Sb on the B-sites. However, Zn is displaced off-centre in the A-sites to achieve lower co-ordination number with realistic ZnO bond lengths. Additional structural complexities arise from: displacement of O(2) atoms; partial occupancies of O(1) and O(2) sites; partial occupancy of a third, interstitial oxygen site, O(3). Since the multiplicities of the off-centre sites are much higher than those of the ideal positions, there is considerable possibility for correlated short range order throughout the structures.     

Critical covalence and superconductivity in Ln2−xCexCuO4

The variations of superconductive properties with x of the n-type Ln_2−xCe_xCuO₄ (Ln = La_0.5Nd_0.5, Nd, or Gd) systems have been investigated. As the size of Ln³⁺ decreases, (i) the solubility limit x of Ce decreases, (ii) the value of x at which a transition from antiferromagnetic semiconductor to superconductor occurs increases, and (iii) the width Δx of the superconductive region decreases. The decreasing solubility of Ce with decreasing size of Ln³⁺ is due to decreasing tensile strain in the CuO₂ sheets. The progressive shift of the semiconductor to superconductor transition to higher x values with decreasing size of Ln³⁺ is explained on the basis of increasing electrostatic Madelung energy E_M caused by decreasing Cu---O bond length. A larger E_M means a larger charge transfer gap Δ and a smaller covalent-mixing parameter λ and bandwidth W; so a decreasing size of Ln³⁺ necessitates a higher level of Ce-doping in order to achieve a critical covalence essential for superconductivity to occur.     

A TEM, XRD, and crystal chemical investigation of oxygen/vacancy ordering in (Ba1−xLax)2In2O5+x, 0x0.6

A careful TEM and XRD study of the (Ba_1−xLa_x)₂In₂O_5+x, 0x0.6, ‘defect-perovskite’-type solid solution has been carried out. A well-defined structural phase transition is shown to occur between x=0.1 and 0.2 from the orthorhombic brownmillerite structure type on the low x side to a multiple twinned, tetragonal 1×1×2 perovskite-related superstructure phase on the high x side at x=0.2. This phase transition correlates with an important phase transition previously observed in electrical conductivity versus temperature measurements. The existence of additional satellite reflections close to the regions of reciprocal space was found to be typical of all (Ba_1−xLa_x)₂In₂O_5+x specimens, although their intensity relative to the parent Bragg reflections systematically reduces as x increases. As x increases beyond 0.2, the -type satellite reflections initially become weaker and rather more diffuse for x=0.3 before splitting into pairs of rather weak and somewhat diffuse incommensurate satellite reflections for x=0.4 and beyond. An interpretation in terms of oxygen vacancy ordering and associated structural relaxation is given. Additional structured diffuse scattering is also observed and a tentative explanation in terms of Ba/La ordering and associated local strain distortions put forward.     

Solid potassium-cation-conducting electrolytes in the systems K2?2 x Fe2? x A x O4 (A = Nb, Ta)

Highly conductive potassium-cation solid electrolytes based on potassium monoferrite with cations Nb⁵⁺ and Ta⁵⁺ partially replacing cations Fe³⁺ are synthesized and studied. Both additives cause a sharp increase in the conductivity of KFeO₂ at temperature below ∼700°C. The two solid electrolytes have similar electric characteristics, which is apparently associated with the close sizes of the doping cations. The increase in the conductivity of potassium monoferrite with the introduction of dopants studied is associated with the formation of potassium vacancies at the substitution Fe³⁺ → Nb⁵⁺ (Ta⁵⁺) + 2 V′_c and also with the elimination of a phase transition typical of pure KFeO₂. Original Russian Text ? E.I. Burmakin, G.Sh. Shekhtman, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 9, pp. 1035–1038. The paper was submitted for the special issue devoted to high-temperature electrochemistry.     

新型固体氧化物燃料电池阴极材料Ca2-xSrxFe2O5的电化学性能研究

采用固相法合成了固体氧化物燃料电池(SOFC)阴极材料2-xSrxFe2O5(x=0.00,0.05,0.10,0.15,0.20),利用XRD和SEM对其结构和微观形貌进行了表征.结果表明该阴极材料与固体电解质Sm0.8Ce0.2O1.9(SDC)在1000℃烧结时不发生化学反应,且烧结4 h后,二者之间可形成良好的接触界面.利用交流阻抗谱技术对阴极材料的电化学性能进行研究,结果显示,阴极上的反应过程主要为电荷的迁移反应,其中Ca1.95Sr0.05Fe2O5电极在空气中700℃下具有最小的极化电阻为0.95Ω·cm2.当测试温度为700℃时,阴极电流密度为74mA·cm-2时,阴极过电位为100mV.     

Crystal structures of Rb2U2O7 and Rb8U9O31, a new layered rubidium uranate

Two alkali metal uranates Rb₂U₂O₇ and Rb₈U₉O₃₁ have been synthesized by solid state reaction at high temperature and their crystal structures determined from single crystal X-ray diffraction data, collected with a three circles Brucker SMART diffractometer equipped by Mo(Kα) radiation and a charge-coupled device (CCD) detector. Their structures were solved using direct methods and Fourier difference techniques and refined by a least-square method on the basis of F² for all unique reflections, with R₁=0.043 for 53 parameters and 746 independent reflections with I?2σ(I) for Rb₂U₂O₇, monoclinic symmetry, space group P2₁/c, , , , β=108.81(1)°, , , Z=2 and R₁=0.036 for 141 parameters and 2065 independent reflections with I?2σ(I) for Rb₈U₉O₃₁, orthorhombic, space group Pbna, , , , , , Z=4.The Rb₂U₂O₇ structure presents a strong analogy with that of K₂U₂O₇ and can be described by layers of distorted UO₂(O₄) octahedra built from dimeric units of edge shared octahedra further linked together by opposite corners. In Rb₈U₉O₃₁ puckered layers are formed by the association of two different uranium polyhedra, pentagonal bipyramids and distorted octahedra. The structure of Rb₈U₉O₃₁ is built from a regular succession of infinite ribbons similar to those observed in diuranates M₂U₂O₇ (MK, Rb) and infinite three polyhedra wide ribbons , to create an original undulated sheets .For both compounds Rb⁺ ions occupy the interlayer space and exhibit comparable mobility with conductivity measurements indicating an Arrhenius-type behavior.     

Properties of the perovskites, SrMn1−xFexO3−δ (x=1/3, 1/2, 2/3)

The SrMn_1−xFe_xO_3−δ (x=1/3, 1/2, 2/3) phases have been prepared and are shown by powder X-ray and neutron (for x=1/2) diffraction to adopt an ideal cubic perovskite structure with a disordered distribution of transition-metal cations over the six-coordinate B-site. Due to synthesis in air, the phases are oxygen deficient and formally contain both Fe³⁺ and Fe⁴⁺. Magnetic susceptibility data show an antiferromagnetic transition at 180 and 140 K for x=1/3 and 1/2, respectively and a spin-glass transition at 5, 25, 45 K for x=1/3, 1/2 and 2/3, respectively. The magnetic properties are explained in terms of super-exchange interactions between Mn⁴⁺, Fe^(4+δ)+ and Fe⁽³⁺⁾⁺. The XAS results for the Mn-sites in these compounds indicate small Mn-valence changes, however, the Mn-pre-edge spectra indicate increased localization of the Mn-e_g orbitals with Fe substitution. The Mössbauer results show the distinct two-site Fe⁽³⁺⁾+/Fe^(4+δ)+ disproportionation in the Mn- substituted materials with strong covalency effects at both sites. This disproportionation is a very concrete reflection of a localization of the Fe-d states due to the Mn-substitution.     

Efficient UV-emitting X-ray phosphors: octahedral Zr(PO4)6 luminescence centers in potassium hafnium–zirconium phosphates K2Hf1−xZrx(PO4)2 and KHf2(1−x)Zr2x(PO4)3

Potassium hafnium–zirconium phosphates, K₂Hf_1−xZr_x(PO₄)₂ and KHf_2(1−x)Zr_2x(PO₄)₃, are broad-band UV-emitting phosphors. At room temperature, they have emission peak maxima at approximately 322 and 305 nm, respectively, under 30 kV peak molybdenum X-ray excitation. Both phosphors demonstrate luminescence efficiencies that make them up to 60% as bright as commercially available CaWO₄ Hi-Plus. The solid-state and flux synthesis conditions, and X-ray excited UV luminescence of these two phosphors are discussed. Even though the two compounds have different atomic structures, they contain zirconium in the same active luminescence environment as that found in highly efficient UV-emitting BaHf_1−xZr_x(PO₄)₂. All the three materials have hafnium and zirconium in octahedral coordination via oxygen-atom corner sharing with six separate PO₄ tetrahedra. This octahedral Zr(PO₄)₆ moiety appears to be an important structural element for efficient X-ray excited luminescence, as are the edge-sharing octahedral TaO₆ chains for tantalate emission.     

Structure and redox properties of CexPr1−xO2−δ mixed oxides and their catalytic activities for CO, CH3OH and CH4 combustion

A series of Ce_xPr_1−xO_2−δ mixed oxides were synthesized by a sol–gel method and characterized by Raman, XRD and TPR techniques. The oxidation activity for CO, CH₃OH and CH₄ on these mixed oxides was investigated. When the value x was changed from 1.0 to 0.8, only a cubic phase CeO₂ was observed. The samples were greatly crystallized in the range of the value x from 0.99 to 0.80, which is due to the formation of solid solutions caused by the complete insertion of Pr into the CeO₂ crystal lattices. Raman bands at 465 and 1150 cm⁻¹ in Ce_xPr_1−xO_2−δ samples are attributed to the Raman active F_2g mode of CeO₂. The broad band at around 570 cm⁻¹ in the region of 0.3 ≤ x ≤ 0.99 can be linked to oxygen vacancies. The new band at 195 cm⁻¹ may be ascribed to the asymmetric vibration caused by the formation of oxygen vacancies. The TPR profile of Pr₆O₁₁ shows two reduction peaks and the reduction process is followed: . The reduction temperature of Ce_xPr_1−xO_2−δ mixed oxides is lower than those of Pr₆O₁₁ or CeO₂. TPR results indicate that Ce_xPr_1−xO_2−δ mixed oxides have higher redox properties because of the formation of Ce_xPr_1−xO_2−δ solid solutions. The presence of the oxygen vacancies favors CO and CH₃OH oxidation, while the activity of CH₄ oxidation is mostly related to reduction temperatures and redox properties.     

Phase diagram, chemical stability and physical properties of the solid-solution Ba4Nb2−xTaxO9

Through the construction of the Ba₄Nb_2−xTa_xO₉ phase diagram, it was discovered that the unique high-temperature γ phase is a thermodynamic intermediate between the low-temperature α phase (Sr₄Ru₂O₉-type) and a 6H-perovskite. Refined site occupancies for the γ phase across the Ba₄Nb_2−xTa_xO₉ solid-solution indicate that Nb preferentially occupies the tetrahedral sites over the octahedral sites in the structure. When annealed in a CO₂-rich atmosphere, all of the phases studied absorb large amounts of CO₂ at high temperatures between ∼700 and 1300 K. In situ controlled-atmosphere diffraction studies show that this behaviour is linked to the formation of BaCO₃ on the surface of the material, accompanied by a Ba₅(Nb,Ta)₄O₁₅ impurity phase. In situ diffraction in humid atmospheres also confirms that these materials hydrate below , and that this plays a critical role in the various reconstructive phase transitions as well as giving rise to proton conduction.