Highly Selective All‐Plastic,Disposable, Cu2+‐Selective Electrodes

Conducting polymers (CP) remain a promising material to construct stable potential all‐solid‐state ion‐selective potentiometric electrodes. The unique properties of poly(3,4‐ethylenedioxythiophene) doped with poly(4‐styrenesulfonate) ions, PEDOT‐PSS: high CP stability and affinity of doping anions towards Cu²⁺ ions, make it highly attractive for construction of all‐solid‐state copper(II)‐selective electrodes with outstanding selectivity. The additional benefits can arise from solution processability of commercially available PEDOT‐PSS system. This material was highly promising for a new sensor arrangement, i.e. to obtain disposable, planar and flexible all‐plastic Cu²⁺‐selective electrodes. These sensors can be obtained by casting a commercially available dispersion of PEDOT‐PSS (Baytron P) on a plastic, non‐conducting support material. The CP being both electrical lead and ion‐to‐electron transducer, was covered with plastic, solvent polymeric Cu²⁺ selective membrane. This extremely simple arrangement, after conditioning in dilute Cu²⁺ solution, was characterized with linear Nernstian responses within the activities range from: 0.1 to 10^?4 M, followed by super‐Nernstian responses for lower activities. The latter result points to effective elimination of primary ions leakage from the plastic membrane / transducer phase and has resulted in significantly improved selectivities. Obtained log K values were equal to ?7.6 for Co²⁺, ?7.4 for Zn²⁺, ?7.2 for Ca²⁺ and ?6.8 for Na⁺, respectively.     

Screen-printed reference electrodes for potentiometric measurements

A convenient and reliable method for large-scale production of miniaturized, planar, all-solid-state reference electrodes is reported. All elements of the Ag/AgCl/KCl reference half-cell i.e. layer of Ag/AgCl (inner electrode), immobilized electrolyte (junction) and encapsulation are fabricated by means of screen-printing technology. The use of pastes cured in low temperature allows fabrication on low-cost, plastic, flexible foils. The developed reference electrodes exhibit good long-term stability. Continuous operation life-time exceeds one week. Storage stability is longer than 9 months. pH, chlorides as well as other halide anions, typical buffer components, alkaline and heavy metal cations, complexing ligands and redox agents, do not influence the potential of the reference electrodes. The developed reference electrodes are compatible with strip potentiometric sensors fabricated in the same format. Examples of analytical applications of the reference electrodes with various screen-printed sensors are demonstrated.     

All-solid-state reference electrodes based on conducting polymers

A novel construction of solution free (pseudo)reference electrodes, compatible with all-solid-state potentiometric indicator electrodes, has been proposed. These electrodes use conducting polymers (CP): polypyrrole (PPy) or poly(3,4-ethylenedioxythiophene) (PEDOT). Two different arrangements have been tested: solely based on CP and those where the CP phase is covered with a poly(vinyl chloride) based outer membrane of tailored composition. The former arrangement was designed to suppress or compensate cation- and anion-exchange, using mobile perchlorate ions and poly(4-styrenesulfonate) or dodecylbenzenesulfonate anions as immobilized dopants. The following systems were used: (i) polypyrrole layers doped simultaneously by two kinds of anions, both mobile and immobilized in the polymer layer; (ii) bilayers of polypyrrole with anion exchanging inner layer and cation-exchanging outer layer; (iii) polypyrrole doped by surfactant dodecylbenzenesulfonate ions, which inhibit ion exchange on the polymer/solution interface. For the above systems, recorded potentials have been found to be practically independent of electrolyte concentration. The best results, profound stability of potentials, have been obtained for poly(3,4-ethylenedioxythiophene) or polypyrrole doped by poly(4-styrenesulfonate) anions covered by a poly(vinyl chloride) based membrane, containing both anion- and cation-exchangers as well as solid potassium chloride and silver chloride with metallic silver. Differently to the cases (i)-(iii) these electrodes are much less sensitive to the influence of redox and pH interferences. This arrangement has been also characterized using electrochemical impedance spectroscopy and chronopotentiometry.     

Potentiometric response of poly(3-octylthiophene), poly(3-methylthiophene) and polythiophene in aqueous solutions

The potentiometric response of some polythiophenes in aqueous solutions has been investigated. Polythiophene (PT), poly(2,2'-bithiophene) (PBT), poly(3-methylthiophene) (PMT), poly(3-octylthiophene) (POT) and poly(4,4'-dioctyl2,2'-bithiophene) (POTd) were electrochemically deposited on platinum in 0.1M LiBF(4)-propylene carbonate solution containing the corresponding monomer or dimer. Polymer electrodes were also prepared by solution casting of chemically synthesized poly(3-octylthiophene) (POTc) dissolved in chloroform. After film deposition (electrochemical or chemical) the polymer coated electrodes were used as indicator electrodes in potentiometric measurements. The open-circuit potential of the polymer electrodes was measured in aqueous solutions containing inorganic salts (10(-1)-10(-4)M). Interestingly, all the polythiophenes studied were found to give a cationic response to monovalent cations such as H(+), Li(+), Na(+), K(+) and NH(+)(4) (Cl(-) salts). The slope, calculated from the linear part of the response curve, was found to depend on the polythiophene used but always remained lower than that predicted for a Nernstian response. The polythiophenes also showed some sensitivity to divalent cations such as Mg(2+) and Ca(2+) (Cl(-)-salts). POT was used as the polymer to study the influence of the polymerization conditions on the potentiometric response. By investigating different polymers from the polythiophene family it was possible to evaluate how the starting material (monomer or dimer) and the presence of alkyl side-chains influence the potentiometric response of the polymer membranes.     

Voltammetric Properties of All‐solid State Ion‐selective Electrodes with Multiwalled Carbon Nanotubes‐poly(3‐octylthiophene‐2,5‐diyl) Nanocomposite Transducer

Voltammetric response of an all‐solid‐state ion‐selective electrode was studied on example of potassium‐selective sensor with poly(vinyl chloride) based membrane and nanocomposite transducer containing poly(3‐octylthiophene‐2,5‐diyl) and multiwalled carbon nanotubes. Factors limiting the rate of the electrochemical process and the response were discussed. The challenge in voltammetric applications of ion‐selective electrodes is thickness of the plastic membrane. It was found that although a relatively thick ion‐selective membrane was applied, as typically used in potentiometric studies, the position of the reduction peak, corresponding to potassium ions incorporation, was dependent on ions concentration in a Nernstian manner. This opens possibility of deviation from the paradigm of ultrathin membranes in voltammetric applications, thus potentially extending the sensors lifetime. The high resistance of the membrane did not affect the voltammetric characteristics, because the resistance was independent of ions concentration in solution. On the other hand, high resistance results in charge trapping effect in the solid contact material, leading to advantageous retention of the oxidized‐conducting state of the solid contact, independently of the applied electrode potential.     

Electrochemical and surface characterization of pH sensor based on bisulfate-doped poly(pyrrole)

Pyrrole was electrochemically polymerized on glassy carbon support in NaHSO₄ solutions under different conditions (method applied, concentration of monomer, concentration of the main solution, thickness of the film). These variables were used to study the preparation effect on the resulting properties, in particular on the potentiometric response of the PPy-HSO₄ electrodes. The electrodes were characterized by cyclic voltammetry, as well as by STM and AES techniques. Utilities of the polymer application as a sensor were studied by direct potentiometric measurements. The results obtained show that poly(pyrrole) doped with bisulfate ions can serve as pH sensor, with the slope of E/pH curves approaching the theoretical value.     

Mercury(II) ion-selective electrodes based on heterocyclic systems

Mercury ion-selective electrodes (ISEs) were prepared with a polymeric membrane based on heterocyclic systems: 2-methylsulfanyl-4-(4-nitro-phenyl)-l-p-tolyl-1H-imidazole (I) and 2,4-diphenyl-l-p-tolyl-1H-imidazole (II) as the ionophores. Several ISEs were conditioned and tested for the selection of common ions. The electrodes based on these ionophores showed a good potentiometric response for Hg2+ ions over a wide concentration range of 5.0 x 10(5-) - 1.0 x 10(-1)M with near-Nernstian slopes. Stable potentiometric signals were obtained within a short time period of 20 s. The detection limits, the working pH range of the electrodes were 1.0 x 10(-5) M and 1.6-4.4 respectively. The electrodes showed better selectivity for Hg2+ ions over many of the alkali, alkaline-earth and heavy metal ions. Also sharp end points were obtained when these sensors were used as indicator electrodes for the potentiometric titration of Hg2+ ions with iodide ions.     

Silver and lead all-plastic sensors—polyaniline vs. poly(3,4-ethyledioxythiophene) solid contact

Silver and lead selective all-plastic ion-selective electrodes were obtained using poly(vinyl chloride)-based membranes and either poly(3,4-ethylenedioxythiophene) or polyaniline dispersion cast on an insulating plastic support as transducer and electrical lead. The effect of interactions of applied conducting polymer with analyte ions on potentiometric responses was evaluated and correlated with changes in elemental composition and element distribution within the ion-selective membrane and the conducting polymer transducer revealed in course of laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) experiments. In the case of silver selective electrodes, potentiometric responses obtained are much dependent on the oxidation state of the polymer placed beneath the ion-selective membrane. For semi-oxidized polymer (poly(3,4-ethylenedioxythiophene)-based electrodes, linear responses with detection limit equal to 10^−5.4 M were obtained. For a more oxidized polyaniline (of higher conductivity), although the electrodes were pretreated exactly in the same way and tested in parallel, super Nernstian potential slope was recorded within the AgNO₃ activities range form 10⁻⁶ to 10⁻⁷ M. These responses were consistent with results of LA-ICP-MS, revealing profoundly higher silver signals intensities for poly(3,4-ethylenedioxythiophene) underlying silver selective membrane. It seems highly probable that silver is accumulated in this polymer layer as Ag⁰ due to spontaneous redox reaction leading to oxidation of the polymer; however, this process requires also the presence of silver ions at the interface. In fact, when reduced (deprotonated) polyaniline was used as transducer, the potentiometric responses of the sensor were, within the range of experimental error, the same as obtained for poly(3,4-ethylenedioxythiophene)-based sensor. On the other hand, for lead(II) selective sensors, the difference in responses of electrodes prepared using poly(3,4-ethylenedioxythiophene) or polyaniline was less pronounced, which is in accordance with the elemental composition of these sensors.     

Electrokinetic characterization of poly(acrylic acid) and poly(ethylene oxide) brushes in aqueous electrolyte solutions

Surfaces carrying hydrophilic polymer brushes were prepared from poly(styrene)-poly(acrylic acid) and poly(styrene)-poly(ethylene oxide) diblock copolymers, respectively, using a Langmuir-Blodgett technique and employing poly(styrene)-coated planar glass as substrates. The electrical properties of these surfaces in aqueous electrolyte were analyzed as a function of pH and KCl concentration using streaming potential/streaming current measurements. From these data, both the zeta potential and the surface conductivity could be obtained. The poly(acrylic acid) brushes are charged due to the dissociation of carboxylic acid groups and give theoretical surface potentials of -160 mV at full dissociation in 10(-)(3) M solutions. The surface conductivity of these brushes is enormous under these conditions, accounting for more than 93% of the total measured surface conductivity. However, the mobility of the ions within the brush was estimated from the density of the carboxylic acid groups and the surface conductivity data to be only about 14% of that of free ions. The poly(ethylene oxide) (PEO) brushes effectively screen the charge of the underlying substrate, giving a very low zeta potential except when the ionic strength is very low. From the data, a hydrodynamic layer thickness of the PEO brushes could be estimated which is in good agreement with independent experiments (neutron reflectivity) and theoretical estimates. The surface conductivity in this system was slightly lower than that of the polystyren substrate. This also indicates that no significant amount of preferentially, i.e., nonelectrostatically attracted, ions taken up in the brush.     

Cobalt ion-doped polyaniline,poly(N-methylaniline), and poly(N-ethylaniline): electrosynthesis and characterisation using electrochemical methods in acidic solutions

Cobalt ion (Co²⁺)-doped polyaniline (PANI-Co), poly(N-methylaniline) (PNMA-Co), and poly(N-ethylaniline) (PNEA-Co) films were synthesised electrochemically on a pencil graphite electrode (PGE) and their electrochemical properties were investigated for supercapacitor applications. The polymer film-coated electrodes (PGE/PANI-Co, PGE/PNMA-Co, and PGE/PNEA-Co) thus obtained were characterised by scanning electron microscopy (SEM) and different electrochemical methods. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements were employed in 0.1 M H₂SO₄ solution to calculate the specific capacitance (C _S) values of the electrodes. The maximum C _S of 192.94 F g^?1, 139.83 F g^?1, and 47.12 F g^?1 were achieved for PGE/PANI-Co, PGE/PNMA-Co, and PGE/PNEA-Co at 1 mV s^?1, respectively. On the other hand, the charge/discharge stability of the electrodes was analysed using the repeating chronopotentiometry (RCP) method. The RCP measurements indicate that the electrodes could be used as an electrode active material for low voltage supercapacitor applications.     

Highly Reproducible Flexible Ion-selective Electrodes for the Detection of Sodium and Potassium in Artificial Sweat

It is well known that potentiometric sensors provide a versatile, cost-effective, and efficient platform for wearable applications. Unfortunately, mass production and commercialization of such devices is often constrained by the requirement of a calibration step, which is due to the poor sensor-to-sensor reproducibility and the need of conditioning the electrodes in the analyte before use. Herein, we fabricated calibration-free flexible sensors including ion-selective electrode and reference electrode by integrating single-walled carbon nanotubes (SWCNTs) with poly(3-octylthiophene) (POT) and applying on polyethylene terephthalate (PET) substrate. The developed sodium and potassium ion-selective electrodes (ISEs) display excellent repeatability, selectivity, stability as well as high sensor-to-sensor reproducibility, with a standard deviation of as low as 1.0 mV in artificial sweat microliter samples volume.     

Electrochemical Behaviour of Poly(benzopyrene) Films Doped with Eriochrome Black T as a Pb2+‐Sensitive Sensors

Poly(benzopyrene) films were electrosynthesized on glassy carbon disk electrodes from benzo(a)pyrene by cyclic voltammetry in the presence of eriochrome black T, which forms strong complexes with lead ions. In consequence, by conditioning the films in high concentration of lead (0.1 mol dm^?3 Pb(NO₃)₂) potentiometric sensitivity to lead ions down to 10^?5 mol dm^?3 Pb²⁺ was induced, and a novel type of lead‐sensitive electrode was obtained. The electrode is characterized by high stability of the potential readouts, good reproducibility of the calibration curves as well as a minor hysteresis effects. The performance of our lead‐sensitive electrode was favourable compared to PEDOT and PPy‐based electrodes doped with eriochrome black T. We conclude that poly(benzopyrene) doped with eriochrome black T is a new electroactive material that may be applied in sensor technology.     

Solid-contact Cu(II) ion-selective electrode based on 1,2-di-(<Emphasis Type="Italic">o</Emphasis>-salicylaldiminophenylthio)ethane

The development of Cu(II) solid-contact ion-selective electrodes, based on 1,2-di-(o-salicylaldiminophenylthio)ethane as a neutral carrier, is presented. For the electrodes construction, unmodified carbon ink (type 1 electrode) and polymer membrane-modified carbon ink (type 2 electrode) were used as solid support and transducer layer. Also, carbon ink composite polymer membrane electrode (type 3 electrode) was prepared. The analytical performance of the electrodes was evaluated with potentiometry, while bulk and interfacial electrode features were provided with electrochemical impedance spectroscopy. It is shown that modification of carbon ink with polymer membrane cocktail decreases the bulk contact resistance of the transducer layer and polymer membrane, thus enhancing the analytical performance of the electrode in terms of sensitivity, linear range, and stability of potential. The optimized electrodes of types 2 and 3 exhibit a wide linear range with detection limits of 1.8 × 10⁻⁶ and 1.6 × 10⁻⁶ M, respectively. They are suitable for determination of Cu²⁺ in analytical measurements by direct potentiometry and in potentiometric titrations, within pH between 2.3 and 6.5. The electrodes are selective for Cu²⁺ over a large number of tested transition and heavy metal ions.     

High-performance pyrrolidinium-based poly(ionic liquid) binders for Li-ion and Li-air batteries

The role of binders is crucial to achieve high performance and long cycle lifes in next-generation electrodes for lithium batteries. Currently used binders in electrode configurations, such as poly(vinylidene difluoride) (PVDF) are inactive polymers that do not transport lithium ions themselves, causing restrictions for high-power applications. Thus, developing innovative binders with an affinity towards lithium mobility is important for both lithium-ion and lithium-air batteries. In this work, we present for the first time the use of PDADMA poly(ionic liquid)s with fluorinated anions (FSI, TFSI, BETI, and CFSO) as cathode binders in Li-ion and Li-air batteries. The high-voltage NMC 532 cathodes with fluorinated PDADMA binders showed improved cells performances as: capacity values, rate performance, and cycling stability in accelerating aging conditions dedicated for more environmental-friendly mobility applications. Especially, PDADMA-CFSO binder in cathodes shows a cell capacity increase of 26% at 5C (12 min charge), when compared to PVDF one. Moreover, the fluorinated PDADMA binders in cathode improve the discharge capacities in Li–O₂ cells, both with liquid and solid gel polymer electrolytes. Impressively, the Coulombic efficiency improves by 146% and the cycling capacity by 70% in solid-state Li–O₂ cells using PDADMA-CFSO binder in the cathode, instead of common lithiated Nafion. All in all, the proposed fluorinated PDADMA Poly(ionic liquid)s can be a highly competitive alternative to conventional binders used nowadays in Li-ion and Li-air batteries.     

邻菲咯啉冠醚衍生物为载体的伯胺药物电极及机理研究

合成了邻菲咯啉-18-冠-6等四种含邻菲咯啉结构的冠醚化合物, 并用作载体制备伯胺电极, 以苄胺为模型化合物, 研究了电极特性, 并制备了测试美西律药物的选择性电极。研究了实验条件对电极性能的影响。用正交多项式回归法优化电极的膜组成。苄胺电极的线性范围1.0×10^-5~0.1mol/L, 斜率55.6mV/pc, 检测下限2.0×10^-6mol/L。美西律电极的线性范围6.0×10^-6~0.1mol/L, 检测下限8.0×10^-7mol, 斜率58.0mV/pc。同时研究了冠醚推动伯胺穿透大块液膜的传输行为。     

Glassy carbon electrodes modified by multiwalled carbon nanotubes and poly(neutral red): A comparative study of different brands and application to electrocatalytic ascorbate determination

The electrochemical behaviour of glassy carbon electrodes coated with multiwalled carbon nanotubes (MWCNT) from three different sources and with different loadings has been compared, with a view to sensor applications. Additionally, poly(neutral red) (PNR) was electrosynthesised by potential cycling on bare glassy carbon and on MWCNT-modified glassy carbon electrodes, and characterised by cyclic voltammetry and scanning electron microscopy. Well-defined voltammetric responses were observed for hexacyanoferrate (II) oxidation with differences between the MWCNT types as well as from loading. The MWCNT and PNR/MWCNT-modified electrodes were applied to the oxidative determination of ascorbate, the electrocatalytic effects observed varying according to the type of nanotubes. Comparison was made with electrodes surface-modified by graphite powder. All modified electrode configurations with and without PNR were successfully employed for ascorbate oxidation at +0.05 V vs saturated calomel electrode with detection limits down to 4 μM; good operational stability and storage stability were also obtained.     

Lead selective membrane electrode using cryptand(222) neutral carrier

The construction, performance characteristics and applications of a polymeric membrance electrode for lead(II) ion are reported. The electrode was prepared by incorporating cryptand(222) as the neutral carrier into a plasticized poly(vinyl chloride) membrane. The influence of membrane composition, pH and concentration of internal reference solution were investigated. The electrode exhibits a potentiometric response for Pb²⁺ ion over the concentration range 10^–1–10^–5 M with a detection limit of 5 × 10^–6 M Pb²⁺. It shows a relatively fast response time of about 30 s and can be used for about two months without any considerable divergence in potential. The proposed sensor revealed good selectivities for Pb²⁺ in the presence of several metal ions and could be used in the pH range of 2.5 to 7.5. It was used as an indicator electrode in the potentiometric titration of Pb²⁺ with EDTA. Received: 20 November 1998 / Revised: 26 March 1999 / Accepted: 31 March 1999     

Lead selective membrane electrode using cryptand(222) neutral carrier

The construction, performance characteristics and applications of a polymeric membrance electrode for lead(II) ion are reported. The electrode was prepared by incorporating cryptand(222) as the neutral carrier into a plasticized poly(vinyl chloride) membrane. The influence of membrane composition, pH and concentration of internal reference solution were investigated. The electrode exhibits a potentiometric response for Pb²⁺ ion over the concentration range 10^–1–10^–5 M with a detection limit of 5 × 10^–6 M Pb²⁺. It shows a relatively fast response time of about 30 s and can be used for about two months without any considerable divergence in potential. The proposed sensor revealed good selectivities for Pb²⁺ in the presence of several metal ions and could be used in the pH range of 2.5 to 7.5. It was used as an indicator electrode in the potentiometric titration of Pb²⁺ with EDTA. Received: 20 November 1998 / Revised: 26 March 1999 / Accepted: 31 March 1999     

Characterization of poly(3,4-ethylenedioxythiophene):tosylate conductive polymer microelectrodes for transmitter detection

In this paper we investigate the physical and electrochemical properties of micropatterned poly(3,4-ethylenedioxythiophene):tosylate (PEDOT:tosylate) microelectrodes for neurochemical detection. PEDOT:tosylate is a promising conductive polymer electrode material for chip-based bioanalytical applications such as capillary electrophoresis, high-performance liquid chromatography, and constant potential amperometry at living cells. Band electrodes with widths down to 3 μm were fabricated on polymer substrates using UV lithographic methods. The electrodes are electrochemically stable in a range between -200 mV and 700 mV vs. Ag/AgCl and show a relatively low resistance. A wide range of transmitters is shown to oxidize readily on the electrodes. Kinetic rate constants and half wave potentials are reported. The capacitance per area was found to be high (1670 ± 130 μF cm(-2)) compared to other thin film microelectrode materials. Finally, we use constant potential amperometry to measure the release of transmitters from a group of PC 12 cells. The results show how the current response decreases for a series of stimulations with high K(+) buffer.     

Amperometric enzyme electrodes of glucose and lactate based on poly(diallyldimethylammonium)-alginate-metal ion-enzyme biocomposites

Sodium alginate (AlgNa) and poly(diallyldimethylammonium chloride) (PDDA) were mixed to obtain an interpenetrating polymer composite via electrostatic interaction and then cast on an Au electrode surface, followed by incorporation of metal ions (e.g. Fe³⁺ or Ca²⁺, to form AlgFe or AlgCa hydrogel) and glucose oxidase (GOx) (or lactate oxidase (LOx)), to prepare amperometric enzyme electrodes. The interactions of PDDA, Alg, and Fe³⁺ are studied by visual inspection as well as microscopic and electrochemical methods. Under optimized conditions, the PDDA-AlgFe-enzyme/Au and PDDA-AlgCa-enzyme/Au electrodes can give good analytical performance (e.g. nM-scale limit of detection of glucose or lactate, and sensitivities > 50 μA cm⁻² mM⁻¹) in the first-generation biosensing mode, which are better than the reported analogs using typical polysaccharide biopolymers as enzyme-immobilization matrices. The enzyme electrodes also worked well in the second-generation biosensing mode in the coexistence of p-benzoquione or ferrocene monocarboxylic acid artificial mediator. Biofuel cells (BFCs) with the enzyme electrodes as the bioanodes and glucose (or lactate) as the biofuel were also fabricated with satisfactory results. The proposed protocols for preparation of high performance Alg-based biocomposites may find wide applications in bioanalysis.