Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

磺化聚醚醚酮与壳聚糖共混制备直接甲醇燃料电池用质子交换膜

给出了不同磺化度下的磺化聚醚醚酮(SPEEK)用作质子交换膜的一系列性能,另外提出了一种新型的酸碱共混质子交换膜,其中,磺化聚醚醚酮和壳聚糖分别被选为酸性、碱性高分子电解质,并对所制备的质子交换膜的相关性能如质子传导性,甲醇渗透性,吸水率以及膜溶胀性、热稳定性等进行了表征,结果表明此种新型复合膜尽管在质子传导性能方面有所下降,阻醇性能改变不大,但是膜溶胀性和吸水率方面有了较大的改善.磺化度为71.4%的SPEEK与壳聚糖以5∶1摩尔比共混制备的质子交换膜,其性质可以与商品化的Nafion 117相媲美,有望在甲醇燃料电池中得到应用.     

磺化酚酞型聚醚砜膜的制备及其阻醇和质子导电性能

直接甲醇燃料电池 (Directmethanolfuelcell,DMFC)以高效、清洁和燃料储运方便等优点适宜于作为各种用途的可移动动力源 ,成为 2 0世纪 90年代以来研究与开发的热点[1,2 ] .目前 ,这种电池的研究难点主要集中在催化剂不稳定和质子交换膜透醇上 .一张好的DMFC膜不但要可传递质子、绝缘电子 ,还应具有良好的阻醇性能 .如果膜的阻醇性能不好 ,甲醇会穿过膜到达阴极 ,与氧直接反应而不产生电流 ,不但造成燃料的浪费 ,同时也影响阴极的正常反应 ,使电池效率下降[3 ] .目前广泛应用于燃料电池中的Nafion 系列膜是由美国DuPont公司生产的一种…     

填充型具有微孔结构的磺化聚芳醚砜/聚醚砜复合质子交换膜的制备及性能

制备了基于磺化聚芳醚砜(SPAES)及聚醚砜(PES)的填充型复合质子交换膜, 研究了其吸水率、 尺寸变化、 热-机械特性、 质子电导率、 甲醇透过性及稳定性等性能. 通过浸入沉淀相转化法, 采用磺化度分别为30%(S30), 40%(S40)及50%(S50)的SPAES与PES制备了系列微孔型复合质子交换膜 Sx-y(x为SPAES的磺化度, y为SPAES的质量分数); 然后利用真空抽滤法在微孔中填充S50制备了相应的填充型复合质子交换膜Sx-y+F50. 结果表明, 由于微孔的引入及皮层结构的存在, Sx-y膜在低离子交换容量(IEC)条件下仍具有较高的电导率、 优良的机械强度、 优异的化学稳定性及较低的甲醇透过性. 经S50填充后, Sx-y+F50膜的IEC及电导率明显提升, 甲醇透过率大幅下降, 但机械强度及化学稳定性未见劣化. 其中S30-40+F50膜(IEC=0.69 mmol/g)的综合性能最佳, 其质子电导率在90 ℃水中达到50.4 mS/cm; 经140 ℃水处理24 h后失重率仅为8.2%, 质子电导率降低仅9%; 经过芬顿试剂(3% H₂O₂, 20 mg/L FeSO₄, 80 ℃, 1 h)处理后失重率仅为0.66%; 甲醇透过率仅为6.8×10^-8 cm²/s.     

新型萘酐型磺化聚酰亚胺质子交换膜的合成

以新型磺化二胺单体, 1,4-双(4-胺基-2-磺酸基苯氧基)苯(DS-TBDA)与非磺化单体1,4′-二胺基二苯醚（ODA）、 1,4,5,8-萘四酸二酐(NTDA)为原料, 采用高温聚合法, 制备了一系列具有不同磺化度的萘酐型磺化聚酰亚胺(S-PI)质子交换膜材料, 并研究了材料性能与结构的关系. 磺化度超过33%时, 质子传导率可达到与Nafion膜同一数量级的水平, 而甲醇透过率均在2.85×10-7 cm2/s以下, 比Nafion膜低1-2个数量级. 研究结果表明, 该膜有望在直接甲醇燃料电池(DMFC)中获得应用.     

含氨基磺化聚芳醚酮砜质子交换膜的制备与性能

通过四元缩聚的方法合成了带有氨基的磺化度可控的磺化聚芳醚酮砜共聚物(Am-SPAEKS). 采用红外光谱和核磁共振谱表征了Am-SPAEKS共聚物的结构. 该共聚物膜具有较好的热性能、尺寸稳定性、较高的质子传导率和阻醇能力. 在80℃时Am-SPAEKS-1膜的质子传导率达到0.0894 S/cm, 而其甲醇渗透系数在25℃时为0.24×10^-6 cm²/s, 低于相同温度下SPAEKS膜(0.87×10^-6 cm²/s)和Nafion膜(2×10^-6 cm²/s). 结果表明, Am-SPAEKS膜能够满足质子交换膜燃料电池(PEMFC)的使用要求.     

DMFC用PES/SPEEK共混阻醇质子交换膜

将磺化聚醚醚酮(SPEEK, 磺化度DS为68.3%)和聚醚砜(PES)两种聚合物共混制得PES/SPEEK共混膜. DSC研究表明两种聚合物之间具有较好的相容性, 因而共混膜均匀致密, 未发生大尺度相分离. PES的混入能有效降低膜的溶胀度及甲醇透过系数. 纯SPEEK 膜40 ℃时在1 mol•L−1甲醇水溶液中溶胀度达到160%, 45 ℃时就完全溶解, 而含30%(w)PES的共混膜在80 ℃时的溶胀度仅有15%. 室温下含20%−30%(w)PES的共混膜的甲醇透过系数为1×10−7 cm2•s−1左右, 比Nafion 115膜的透过系数小一个数量级. 尽管80 ℃下30%(w)PES/SPEEK共混膜的电导率与Nafion 115膜相当, 但由于共混膜的厚度比Nafion 115膜小1/3左右, 膜电阻较小, 因而其电池性能比Nafion 115膜的好.     

钛酸钡掺杂磺化聚醚酮质子膜的制备与性能

将纳米钛酸钡(BT)在环己烷中超声分散制得均匀的悬浊液后,与磺化聚醚酮的二甲亚砜溶液均匀混合,然后采用流延法制备了掺杂质子交换膜。 通过环镜扫描电子显微镜表征发现BT在膜中分散均匀,通过吸水率、溶剂吸收率、尺寸变化、电导率、甲醇透过率、力学性能及稳定性等测试发现掺杂膜虽然电导率有所下降,但是其抗溶胀性、稳定性和力学性能显著提高。     

Synthesis and characterization of poly(arylene ether ketone)s bearing pendant sulfonic acid groups for proton exchange membrane materials

A bisphenol monomer (2,5‐dimethoxy)phenylhydroquinone was prepared and further polymerized to obtain poly(arylene ether ketone) copolymers containing methoxy groups. After demethylation and sulfobutylation, a series of novel poly(arylene ether ketone)s bearing pendant sulfonic acid group (SPAEKs) with different sulfonation content were obtained. The chemical structures of all the copolymers were analyzed by ¹H NMR and ¹³C NMR spectra. Flexible and tough membranes with reasonably good mechanical properties were prepared. The resulting side‐chain‐type SPAEK membranes showed good dimensional stability, and their water uptake and swelling ratio were lower than those of conventional main‐chain‐type SPAEK membranes with similar ion exchange capacity. Proton conductivities of these side‐chain‐type sulfonated copolymers were higher than 0.01 S/cm and increased gradually with increasing temperature. Their methanol permeability values were in the range of 1.97 × 10^?7–5.81 × 10^?7 cm²/s, which were much lower than that of Nafion 117. A combination of suitable proton conductivities, low water uptake, low swelling ratio, and high methanol resistance for these side‐chain‐type SPAEK films indicated that they may be good candidate material for proton exchange membrane in fuel cell applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

磺化聚醚醚酮膜的制备及其阻醇和质子导电性能

直接甲醇燃料电池 (Ｄｉｒｅｃｔｍｅｔｈａｎｏｌｆｕｅｌｃｅｌｌ,ＤＭＦＣ)以高效、清洁和燃料储运方便等优点适宜于作为各种用途的可移动动力源 ,成为 2 0世纪 90年代以来研究与开发的热点[1,2 ] .目前 ,这种电池的研究难点主要集中在催化剂不稳定和质子交换膜透醇上 .一张好的ＤＭＦＣ膜不但要可传递质子、绝缘电子 ,还应具有良好的阻醇性能 .如果膜的阻醇性能不好 ,甲醇会穿过膜到达阴极 ,与氧直接反应而不产生电流 ,不但造成燃料的浪费 ,同时也影响阴极的正常反应 ,使电池效率下降[3] .目前广泛应用于燃料电池中的Ｎａｆｉｏｎ系列膜…     

A novel proton-conductive membrane with reduced methanol permeability prepared from bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO)

A series of proton-conducting membranes were developed for direct methanol fuel cell (DMFC) applications via sulfonation of bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO) base membranes. Besides the low manufacture cost, the membranes exhibited an excellent control on methanol crossover and swelling, and a sound balance with high proton conductivities. These can be attributed to the inherent properties of membrane structures: (i) benzyl substitution with bromine, which imparted the membrane stronger hydrophobicity, (ii) cross-linking between BPPO chains, which enhances the dimensional stability and renders the membrane a dense texture, (iii) proper content of sulfonic acid groups, which guarantees the proton conductivity. An optimal membrane was obtained after investigating the effects of the bromination degree and sulfonation process on the performances of corresponding membranes, i.e., the membrane possesses the methanol permeability of 2.64 × 10⁻⁸ cm²/s and characteristic factor Φ value of 30 times higher than that of Nafion^® 117. The sulfonation process should be controlled within a proper period of time and in mild sulfonation conditions so as to achieve a proton conductivity higher than 0.07 S/cm for potential applications in DMFC.     

直接甲醇燃料电池中的膜性能比较

制备了磺化聚醚醚酮(SPEEK)和磺化酚酞型聚醚砜(SPES-C)两种质子交换膜,考察了其质子导电和阻醇性能.实验发现,两种新型质子交换膜具有一定的化学稳定性和质子电导率,尤其在高温下两种新膜的质子电导率与Nafion膜接近.两种新膜的甲醇透过系数要比Nafion膜的低1～2个数量级.分别以两种新型膜和Nafion115膜为电解质制备了直接甲醇燃料电池膜电极,讨论了膜材料的性能对直接甲醇燃料电池性能的影响.结果表明,膜材料的阻醇性越好,电池的开路电压越高;膜的电导率越高,在较高电流密度区域内电池的性能越好.     

Sulfonated poly(aryl ether ketone)s containing naphthalene moieties obtained by direct copolymerization as novel polymers for proton exchange membranes

A series of sulfonated poly(aryl ether ketone)s (SPAEKs) were prepared by aromatic nucleophilic polycondensation of 2,6‐dihydroxynaphthalene with 5,5′‐carbonyl‐bis(2‐fluorobenzenesulfonate) and 4,4′‐difluorobenzophenone. The structure and degree of sulfonation (DS) of the SPAEKs were characterized using ¹H NMR spectroscopy. The experimentally observed DS values were close to the expected values derived from the starting material ratios. The thermal stabilities of the SPAEKs were characterized by thermogravimetric analysis, which showed that in acid and sodium salt forms they were thermally stable in air up to about 240 and 380 °C, respectively. Transparent membranes cast from the directly polymerized SPAEKs exhibited good mechanical properties in both dry and hydrated states. The dependence of water uptake and of membrane swelling on the DS at different temperatures was studied. SPAEK membranes with a DS from 0.72 to 1.60 maintained adequate mechanical properties after immersion in water at 80 °C for 24 h. The proton conductivity of SPAEK membranes with different degrees of sulfonation was measured as a function of temperature. The proton conductivity of the SPAEK films increased with increased DS, and the highest room temperature conductivity (4.2 × 10^?2 S/cm) was recorded for a SPAEK membrane with a DS of 1.60, which further increased to 1.1 × 10^?1 S/cm at 80 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2866–2876, 2004     

改性聚偏氟乙烯接枝共混聚苯乙烯磺酸膜的制备与性能

将苯乙烯添加到溶有原硅酸钠改性的聚偏氟乙烯(PVDF)N-甲基吡咯烷酮溶液中, 以过氧化苯甲酰(BPO)作引发剂, 苯乙烯直接接枝到原硅酸钠改性的PVDF链上, 成膜后磺化制备了聚偏氟乙烯接枝苯乙烯(PVDF-g-PSSA)膜. 采用傅立叶变换红外光谱(FT-IR)、扫描电镜(SEM)、能量扩散X射线(EDX)和多功能材料实验机表征了膜的结构、形貌及硫和硅的分布、机械强度、溶胀度, 使用阻抗分析和气相色谱仪研究了苯乙烯含量(w)对PVDF-g-PSSA膜的质子导电性能和阻醇性能的影响. 结果表明, 苯乙烯加入后, 原硅酸钠改性的PVDF与苯乙烯进行接枝共聚反应, 苯乙烯磺化反应不只是在膜表面进行, 同时渗入到膜中进行, 机械性能得到了改善. 质子电导率(σ)随苯乙烯质量分数的提高而升高. Na4SiO4为8%和苯乙烯为20%的PVDF-g-PSSA膜, 在25 ℃时溶胀度仅为20.4%, 甲醇透过系数在10-7 cm2·s-1数量级上, 比Nafion115膜的低一个数量级. 该膜具有较高的选择性, 在直接甲醇燃料电池中具有良好的应用前景.     

磺化聚醚醚酮/三羧基丁烷膦酸锆复合质子交换膜的研究

通过在磺化聚醚醚酮(SPEEK)中掺杂1,2,4-三羧基丁烷-2-膦酸锆(Zr(PBTC))制备出SPEEK/Zr(PBTC)复合质子交换膜.结果表明,与纯SPEEK膜相比,Zr(PBTC)的掺杂能降低复合膜的吸液量及甲醇透过系数,且随着Zr(PBTC)含量的增加,这种作用越趋明显.在室温至80℃范围内,复合膜的甲醇透过系数在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,当温度大于90℃时,含40wt%Zr(PBTC)的复合膜电导率超过Nafion115膜,并在160℃时达到0.36S.cm-1.使用温度的提高及在高温下的高电导率表明该复合膜适合在高温DMFC中使用.     

Proton exchange membrane using partially sulfonated polystyrene-b-poly(dimethylsiloxane) for direct methanol fuel cell

A diblock copolymer ionomer containing a rubbery poly(dimethylsiloxane) block has been developed as a proton exchange membrane for direct methanol fuel cell (DMFC). The partially sulfonated polystyrene-b-poly(dimethylsiloxane) (sPS-b-PDMS) membrane with 38% sulfonation degree exhibited 3 times lower methanol permeability and 2.6 times higher membrane selectivity (proton conductivity/methanol permeability) compared to Nafion^® 115 at 25 °C. Coexistence of microphase domains and ionic clusters was confirmed from the morphological studies by small-angle X-ray scattering and tapping-mode atomic force microscopy. Gas chromatographic analysis revealed that water/methanol selectivity of sPS-b-PDMS was 20 times higher than that of Nafion^® 115. Such a high water/methanol selectivity can be attributed to the existence of PDMS microdomains minimizing methanol permeation through hydrophilic ion channels. sPS-b-PDMS membranes were fabricated into membrane electrode assembly (MEA), and air-breathing DMFC test for these MEAs showed a better performance compared to the MEA composed of Nafion^® 115.     

磺化聚醚醚酮/磷钨酸复合膜的导电和甲醇渗透性能

通过磺化反应制备了磺化聚醚醚酮,1H-NMR测试表明其磺化度分别为0.65和0.73.用共混的方法制备了磺化聚醚醚酮/磷钨酸复合质子交换膜.研究了磺化聚醚醚酮的磺化度和磷钨酸的含量对复合膜的吸水性能?电导率,甲醇渗透性能的影响.随着磺化度和磷钨酸含量的增加,电导率逐渐增大,最高达到1.36×10-2S/cm(20℃),高于相同测试条件下NafionR○117膜的电导率(1.0×10-2S/cm).对复合膜的横向和纵向电导率进行了测试和比较,两者相差接近一个数量级.磷钨酸的掺杂虽然没有降低复合膜的甲醇渗透系数,但是仍然都低于相同条件下测得的NafionR○117膜的甲醇渗透系数.     

Synthesis and characterization of sulfonated polyimide membranes for direct methanol fuel cell

The sulfonated polyimide (SPI) membranes for direct methanol fuel cell (DMFC) were synthesized with 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA), 2,2′-benzidinedisulfonic acid (BDSA), 4,4′-oxydianiline (ODA) through classical two-step methods: (1) preparation of sulfonated poly(amic acid) (SPAA) precursors with different sulfonation levels by controlling the molar ratio of BDSA to ODA, and (2) thermal imidization of the SPAA films. The chemical structure and the imidization from SPAA membranes were characterized by FT-IR with temperature, and the sulfonation levels were determined by elemental analysis. The thermal stability of the membranes was also characterized by TGA. From water uptake and small angle X-ray scattering (SAXS) experiments for different sulfonation levels, it was found that the number of water clusters in SPI membranes increased as the water uptake of membranes increased, but the size of water cluster was not changed with the sulfonation levels. The proton conductivity and the methanol permeability of SPI membrane showed a sudden leap like a percolation phenomenon around 35 mol% of sulfonation level. The SPI membranes exhibited relatively high proton conductivity and extremely low methanol permeability, and showed the feasibility of suitable polymer electrolyte membranes (PEM) for DMFC.     

PTFE辐射接枝对苯乙烯基三甲氧基硅烷制备质子交换膜

采用聚四氟乙烯(PTFE)膜室温下共辐射接枝单体p-苯乙烯基三甲氧基硅烷(StSi),之后经磺化和水解缩聚制备了含有亲水性的—Si—O—Si—交联结构和Si—OH基团的质子交换膜.研究了溶剂、吸收剂量、吸收剂量率以及单体浓度等参数对接枝率的影响,并对质子交换膜的离子交换容量(IEC)、吸水性、尺寸稳定性及电导率等性能进行了分析.结果表明,实验条件下接枝率随吸收剂量和单体浓度增加而增加,采用3mol·L-1的单体浓度减少均聚物;吸收剂量率为10～43Gy·min-1时,接枝率随剂量率变化不明显;以甲苯做溶剂可获得较高接枝率并保持膜的机械强度;IEC值、吸水性和电导率随接枝率增加而增大,是—SO3H、—Si—O—Si—交联结构和Si—OH基团共同作用的结果.接枝率72.5%时膜的IEC值为1.53mmol·g-1,高于Nafion117(0.89mmol·g-1),90℃吸水率为63%,尺寸稳定(优于Nafion117),质子电导率达1.5×10-2S·cm-1,获得了低于Nafion117的甲醇透过性,接枝率50.1%时甲醇透过系数0.82×10-6cm2·s-1.     

SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜研究

通过在磺化聚醚醚酮(SPEEK,DS=61.68%)中分别混入酚酞型聚醚砜(PES-C)、磺化酚酞型聚醚砜(SPES-C,DS=53.7%)制备出SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜.结果表明,共混的两种聚合物之间均具有较好的相容性.PES-C、SPES-C的混入能有效降低膜的溶胀及甲醇透过,且随着共混量的增加,这种作用越趋明显.纯SPEEK膜在75℃左右溶解,而SPEEK/PES-C(30wt%)、SPEEK/SPES-C(30wt%)共混膜在80℃时溶胀度仅为22.5%、26.32%.在室温至80℃范围内,纯SPEEK及共混膜的甲醇透过系数都在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,温度大于90℃时,SPEEK/PES-C(20wt%)共混膜电导率超过Nafion115膜;温度大于110℃时,SPEEK/SPES-C(30wt%)共混膜电导率与Nafion115膜相当,达到0.11S.cm-1.高电导率,低透醇系数以及明显提高了的可使用温度表明该类共混膜有望在DMFC中使用.