不饱和聚酯/玻璃纤维复合材料的研究

综述了国内外近年来不饱和聚酯(UPR)/玻璃纤维复合材料的研究与开发的进展,包括不饱和聚酯用量对不饱和聚酯/玻璃纤维复合材料介电性能的影响,光和高能辐射对玻璃纤维/不饱和聚酯树脂复合材料老化性能的影响。重点介绍了不饱和聚酯组成、界面改性、防收缩剂和玻璃纤维分布对玻璃纤维/不饱和聚酯树脂复合材料性能的影响。     

天然植物纤维的改性与树脂基复合材料

对如象黄麻，亚麻，木材纤维，棉等十余种天然纤维的物理和化学改性方法以及将其应用于树脂基复合材料的性能作了系统的评述。     

General Discussion on Chemical Modifications

Recent work on the use of wool in heat- and mass-exchange systems is summarized. Improvements in the transfer of water vapor (e.g., between the inlet and outlet ducts of an air conditioner) have been obtained by application of hydrophilic polymers to the surface of wool fibers. Further improvements in water sorption are obtained by inclusion of deliquescent salts. Drip formation does not occur at high humidities, presumably because of the viscous nature of the polymer/water system. Wool is shown to be a more suitable substrate than polyester.     

五种植物纤维粉填充不饱和聚酯树脂复合材料的性能对比

以芝麻秸秆粉、水稻秸秆粉、玉米芯秆粉、菠萝叶粉、甘蔗渣粉五种不同植物纤维粉为填充体、不饱和聚酯树脂(UPR)为基体制作植物纤维粉/UPR复合材料,对比研究了秸秆种类对复合材料密度、力学性能及吸水性能的影响。结果表明,植物纤维粉粒径为100目、添加量为UPR用量的10%时,芝麻秸秆粉/UPR复合材料的综合力学性能最好,拉伸强度、弯曲强度和冲击强度分别为41.320 MPa、67.467 MPa和2.815 KJ/m^2,且每一浸泡阶段吸水率均最低。     

The Influence of Structural Features on the Chemical Resistance of Unsaturated Polyester Resins

Abstract

Unsaturated polyester resins are widely used in the field of chemical process equipment [1-4] because of their handling properties. For example, large structures of complex shape can be fabricated with simple tools, frequently on the site. In general, unsaturated polyesters do not show an outstanding resistance to strong solutions of corrosive chemicals in contrast with other plastics. Nevertheless, as the chemistry of the unsaturated polyesters developed, special resins were made with excellent resistance to chemicals while maintaining important handling properties.     

Mechanical Properties and Chemical Resistance of Short Tamarind Fiber/Unsaturated Polyester Composites: Influence of Fiber Modification and Fiber Content

In the present work, tamarind fibers were extracted from ripened fruits by the water retting process. Using these fibers as reinforcement and unsaturated polyester as matrix, composite samples were prepared by the hand lay-up technique. The effect of chemical surface treatments (alkali and silane) of tamarind fibers on the mechanical properties, chemical resistance, and interfacial bonding was studied. The mechanical properties of the composites with surface modified fibers were found to be higher than those with unmodified fibers. Morphological studies indicated improvement of interfacial bonding by alkali and silane coupling agent treatments of the fibers. The composites were found to be resistant to many chemicals.     

Modification of Mineral Powder by Various Organic Materials: Their Potential as Reinforcement for Unsaturated Polyester Composites

Russian Journal of Applied Chemistry - Industrial by product dumped from iron making industry (slag) has been modified by various chemical agents, particularly, paraffin wax, liquid nitrile...     

Effect of Chemical Modifications of Fibers on Tensile Properties of Epoxy Hybrid Composites

Treatment of oil palm empty fruit bunch (EFB) and jute fibers is carried out by using 2-hydroxy ethyl acrylate (2-HEA) to increase the interfacial bonding of fibers with the epoxy matrix. Fourier transform-infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) were used to measure the change of surface composition of the fibers after treatment. Modified oil palm and jute fibers were used as reinforcements for epoxy matrix to fabricate hybrid composites by the hand lay-up technique. Tensile and morphological properties of hybrid composites were studied, and tensile properties of hybrid composites prepared from chemically treated oil palm/jute fibers were found to be better than those of untreated hybrid composites. SEM micrographs disclose that interfacial bonding between fiber and matrix significantly improved in the hybrid composites. Developed hybrid composites can be exploited as alternative materials for development of automotive and structural components instead of synthetic fiber–reinforced polymer composites.     

表面活性剂修饰的CuCoMn催化剂催化合成低碳醇

分别采用阳离子（十六烷基三甲基溴化铵,CTAB）、阴离子（十二烷基硫酸钠,SDS）、非离子（三嵌段共聚物,P123）三种不同类型的表面活性剂对CuCoMn基催化剂进行改性,利用N2吸脱附、XRD、XPS、IR手段表征了催化剂的微观结构．在生物质基合成气合成高醇中的应用研究结果表明,SDS修饰的CuCoMn催化剂表现出较高的CO转化率（29．7％）,而CTAB修饰的CuCoMn催化剂具有优良的高醇选择性（41．2％）．同时,三种表面活性剂修饰的催化剂均不同程度地提高了高醇产率及其在醇产物中的比例．由于CTAB修饰的催化剂具有孔径最大、形成的CuCoMnO4尖晶石结构结晶度最高、表面金属原子趋于低价态等特点,这些性质与其良好的高醇合成反应性能有关．在金属沉淀阶段加入CTAB得到的催化剂有利于形成高醇产物．     

脂肪型超支化聚酯的端基改性研究

近年来 ,超支化聚合物以其独特的结构和性能而受到广泛的重视 ,已成为 2 1世纪高分子科学研究的重要方向[1～ 4 ] .超支化聚合物通常是通过 AB2 型单体的缩聚来合成的 ,由于超支化聚酯的单体容易合成 ,因此 ,有关超支化聚酯的研究最为深入 .目前所报道的脂肪型超支化聚酯都是以 2 ,2 -二甲醇基丙酸为原料来合成的 ,Malstrom等 [5～ 7]系统研究了该聚合物的合成及结构 .最近 ,Johansson[8]采用丙烯酰氯对该聚合物端基改性 ,获得了可用于紫外光固化的涂料 ,但是所采用的合成及提纯方法都很复杂 ,并且需要很长的反应时间 .本文采用一种新的…     

Reactive Distillation: An Attractive Alternative for the Synthesis of Unsaturated Polyester

Summary: Unsaturated polyester is traditionally produced in a batch wise operating reaction vessel connected to a distillation unit. An attractive alternative for the synthesis of unsaturated polyester is a reactive distillation. To value such alternative synthesis route reliable process models need to be developed. In this paper, the strategy is described for the development of the reactive distillation model. Essential parts of the reactive distillation model are kinetic and thermodynamic which are subsequently validated with the experimental data of the traditional batch process such as acid value of the polyester, weight of the distillate and glycol concentration in the distillate. We find that the models predict these important variables reliably. Unsaturated polyester production time is around 12 hours in the traditional batch process. However, the simulation study of the reactive distillation process shows that the total production time of unsaturated polyester in a continuous reactive distillation system is between 1.5 hours to 2 hours for the same product quality as during batch production. The equilibrium conversion is raised by 7% compared to the traditional batch process. The model demonstrated that reactive distillation has the potential to intensify the process by factor of 6 to 8 in comparison to the batch reactor.     

电磁功能高分子复合物研究进展

综述了兼具电、磁性质的高分子复合物的最新研究进展.重点评述了通过原位聚合、电化学沉积、自组装等方法制备电磁功能高分子复合物的过程及形成机制,并对电磁功能高分子复合物的潜在应用作了介绍.     

卟啉在纯铁表面上的化学与电化学修饰

通过在卟啉的丙酮－水溶液中循环阳极电位扫描，在工业纯铁表面形成一层修饰层．此修饰层呈淡黄色，结晶细密．与基体结合牢固，耐腐蚀性能良好．质谱分析及反射红外分析说明有铁卟啉螯合物生成．若将工业纯铁直接浸入卟啉的丙酮－水溶液中，其表面同样也可形成一层修饰膜, 此膜较之电化学修饰层疏松而厚．卟啉在纯铁表面的电化学修饰层与化学修饰膜的形成机制有着本质的不同．     

Tunable Electrochemical Peptide Modifications: Unlocking New Levels of Orthogonality for Side-Chain Functionalization

Electrochemical transformations provide enticing opportunities for programmable, residue-specific peptide modifications. Herein, we harness the potential of amidic side-chains as underutilized handles for late-stage modification through the development of an electroauxiliary-assisted oxidation of glutamine residues within unprotected peptides. Glutamine building blocks bearing electroactive side-chain N,S-acetals are incorporated into peptides using standard Fmoc-SPPS. Anodic oxidation of the electroauxiliary in the presence of diverse alcohol nucleophiles enables the installation of high-value N,O-acetal functionalities. Proof-of-principle for an electrochemical peptide stapling protocol, as well as the functionalization of dynorphin B, an endogenous opioid peptide, demonstrates the applicability of the method to intricate peptide systems. Finally, the site-selective and tunable electrochemical modification of a peptide bearing two discretely oxidizable sites is achieved.     

界面聚合法制备复合膜中的改性研究

介绍了复合膜的结构及性能,阐述了界面聚合法的基本原理及用该法制备复合膜的优越性;同时重点综述了国内外对复合膜的性能如通量和截留率、耐氯性、热稳定性、耐溶剂性和抗污染性的研究现状及改进方法,并对界面聚合法制备复合膜存在的问题以及研究前景进行了展望。     

竹纤维增强可生物降解复合材料研究进展

天然植物纤维增强可生物降解复合材料是一类性能优良、环境友好、可自然降解的绿色环保复合材料。众多天然植物纤维中,竹纤维不仅资源丰富、有优异的力学性能,还具有天然抗菌、除臭、吸湿放湿、抗紫外线等优点,广泛应用于复合材料的制备。本文对竹纤维增强可生物降解复合材料的增强体材料和基体材料特性、改性预处理方法、成型工艺和生物降解特性等性能评价的国内外研究现状进行了综述,同时还对竹纤维增强可生物降解复合材料的未来研究和发展趋势进行了展望。     

聚倍半硅氧烷复合超支化聚酯的结构及相容性

以三羟甲基丙烷(TMP)为内核, 二羟甲基丙酸(DMP)为支化单元用准一步法合成了重均分子量为12100的第四代端羟基脂肪族超支化聚酯G4, 并与聚甲基三乙氧基硅烷(PMSQ)共混制备出一系列不同质量分数的复合物. 利用固体核磁共振(NMR)等方法表征了各个样品的结构和反应程度, 并通过测量¹H T_1ρ值发现超支化聚酯与聚倍半硅氧烷之间具有较好的相容性, 相容尺寸为3~5 nm.     

A Revised Structure Model for the UCl6 Structure Type,Novel Modifications of UCl6 and UBr5, and a Comment on the Modifications of Protactinium Pentabromides

The redetermination of the crystal structure of trigonal UCl₆, which is the eponym for the UCl₆ structure type, showed that certain atomic coordinates had been incorrectly reported. This led to noticeably different U−Cl distances within the octahedral UCl₆ molecule (2.41 and 2.51 Å). Within the revised structure model presented here, which is based on single crystal data as well as quantum chemical calculations, all U−Cl distances are essentially equal within standard uncertainty (2.431(5), 2.437(5), and 2.439(6) Å). This room temperature modification, called rt-UCl₆, crystallizes in the trigonal space group P m1, No. 164, hP21, with a=10.907(2), c=5.9883(12) Å, V=616.9(2) ų, Z=3 at T=253 K. A new low-temperature (lt) modification of UCl₆ is also presented that was obtained by cooling a single crystal of rt-UCl_6. The phase change occurs between 150 and 175 K. lt-UCl₆ crystallizes isotypic to a low-temperature modification of SF₆ in the monoclinic crystal system, space group C2/m, No. 12, mS42, with a=17.847(4), b=10.8347(18), c=6.2670(17) Å, β=96.68(2)°, V=1203.6(5) ų, Z=6 at 100 K. The Cl anions form a close-packed structure corresponding to the α-Sm type with uranium atoms in the octahedral voids. During the synthesis of UBr₅ a new modification was obtained that crystallizes in the triclinic crystal system, space group P , No. 2, aP36, with a=10.4021(6), b=11.1620(6), c=12.2942(7) Å, α=68.3340(10)°, β=69.6410(10)° and γ=89.5290(10)°, V=1231.84(12) ų, Z=3 at T=100 K. In this structure the UBr₅ units are dimerized to U₂Br₁₀ molecules. The Br anions also form a close-packed structure of the α-Sm type with adjacent uranium atoms in the octahedral voids. Comparisons of the crystal structures of the compounds MX₅ (M=Pa, U; X=Cl, Br) show that the crystal structure of monoclinic α-PaBr₅ is probably not correct.