Analysis of leachable and total trace metals in air particulate matters by capillary electrophoresis

A new analytical procedure was developed for simultaneous determination of ammonium, leachable and total metals in fine and coarse air particulate matters using a new capillary electrophoresis (CE) procedure, with a new buffer system containing 10 mM histidine, 2 mM 18-crown-6 and 8 mM lactic acids with pH adjusted to 4.0. A two complexes system, 18-crown-6 ether and lactic acid, was developed to solve the co-migration problem of NH(4)(+) and K(+) and to give satisfactory separation of transition metals. Satisfactory separation and quantitation of NH(4)(+), K(+), Ca(2+), Na(+) , Mg(2+) and Zn(2+) were obtained using the CE procedure developed for both leachable and total metals in coarse (10-3 mum) and fine (<3 mum) air particulate matters. Wide working ranges (ppb to ppm range) and sensitive detection limits (ppb) were obtained for the cations investigated. The reliability was established by parallel method comparison with the ICP-AES method. The analytical procedure developed is shown to provide a quick, sensitive, precise and economic method for simultaneous determination of ammonium, leachable and total metals in air particulate matters.     

Separation and determination of cations in beverage products by capillary zone electrophoresis

Cation determination is important for quality control of beverage products. To determine a large group simultaneously, a capillary electrophoresis procedure is developed with indirect UV at 214 nm in a three-complex buffer system (10 mM N,N-dimethylbenzylamine (DBA), 8 mM lactic acid and 2 mM 18-crown-6) with good mobility matching with desired cations. Under optimized conditions with pH adjusted to 4.65, a baseline separation is achieved for 14 cations (Rb(+), NH(4)(+), K(+), Ca(2+), Na(+), Mg(2+), Mn(2+), Co(2+), Fe(2+), Cd(2+), Cr(3+), Ni(2+), Zn(2+) and Cu(2+)) within 7 min using an uncoated silica column. To cover ng/l to mug/l range, both hydrostatic and electrokinetic sampling are studied, showing working ranges within (0.05-50)/(0.005-2) microg/l and detection limits (13-78)/(1.4-10) ng/l, respectively with satisfactory repeatability (RSD 0.31-0.47% for migration time, and 3.0-4.0% for peak height measurement). Agreeable results with established inductively coupled plasma-atomic emission spectrometry method have been obtained for orange juice and tea samples.     

Development and validation of analytical methodology using capillary electrophoresis for separation and determination of anions in rainwater

A new capillary electrophoresis (CE) procedure was developed for simultaneous determination of both organic and inorganic anions in rain water using a background electrolyte (BGE) containing 5 mM molybdate, 0.15 mM CTAH, 0.01% PVA and 5 mM Tris buffer to adjust pH at 7.9. Under optimised conditions, good repeatability (RSD for sulphate in migration time=0.36% and peak area=4.2%), low detection limit (2 ppb for chloride) and satisfactory working range (50 ppb-20 ppm for hydrodynamic injection, 10 ppb-3 ppm for electrokinetic injection for chloride) were obtained. The reliability of the CE procedure developed was established by satisfactory recovery tests and good agreement of results obtained by both the CE and ion chromatography (IC) methods. The procedure developed had been successfully applied for field monitoring of rainwater showing good repeatability and capability of detecting trace anions at ppb levels beyond the IC working range. Thus, the new CE procedure developed provides a quick, sensitive, economic and reliable method to meet the need for the simultaneous determination of both organic and inorganic anions in the acid rain monitoring programme.     

Determination of ammonia, creatinine and inorganic cations in urine using CE with contactless conductivity detection

CE with capacitively coupled contactless conductivity detection (C(4)D) was used to determine waste products of the nitrogen metabolism (ammonia and creatinine) and of biogenic inorganic cations in samples of human urine. The CE separation was performed in two BGEs, consisting of 2 M acetic acid + 1.5 mM crown ether 18-crown-6 (BGE I) and 2 M acetic acid + 2% w/v PEG (BGE II). Only BGE II permitted complete separation of all the analytes in a model sample and in real urine samples. The LOD values for the optimized procedure ranged from 0.8 microM for Ca(2+) and Mg(2+) to 2.9 microM for NH(4)(+) (in terms of mass concentration units, from 7 microg/L for Li(+) to 102 microg/L for creatinine). These values are adequate for determination of NH(4)(+), creatinine, Na(+), K(+), Ca(2+) and Mg(2+) in real urine samples.     

Determination of fluoroquinolones in bovine milk samples using a pipette‐tip SPE step based on multiwalled carbon nanotubes prior to CE separation

A simple CE–UV method was developed for the simultaneous determination of ciprofloxacin, norfloxacin, and ofloxacin in milk samples. The optimum separation was obtained using a 20 mM ammonium dihydrogenphosphate solution with 2 mM cetyltrimethylammonium bromide at pH 3.0 as the BGE. Satisfactory resolution for structurally very similar analytes, like norfloxacin and ciprofloxacin, was achieved without including any organic solvent. Milk samples were prepared using a simple/extraction procedure based on acidic protein precipitation followed by an SPE step using only 5 mg of multiwalled carbon nanotubes as the sorbent material. The LODs for the three compounds were between 7.5 and 11.6 μg/L and the RSDs for the peak areas were between 2.6 and 4.9%. The complete method was applied to spiked real milk samples with satisfactory recoveries for all analytes (84–106%).     

A novel method for analysis of explosives residue by simultaneous detection of anions and cations via capillary zone electrophoresis

A novel electrolyte has been developed for the simultaneous separation of cations and anions in low explosive residue by capillary electrophoresis. This electrolyte contains 15 mM α-hydroxyisobutyric acid (HIBA) as the buffer, 6 mM imidazole as the cation chromophore, 3 mM 1,3,6-naphthalenetrisulfonic acid (NTS) as the anion chromophore, 4 mM 18-crown-6 ether as a cation selectivity modifier, and 5% (v/v) acetonitrile as an organic modifier. The pH was adjusted to 6.5 using tetramethylammonium hydroxide (TMAOH), an electroosmotic flow modifier. The method was optimized by varying the concentrations of α-HIBA, imidazole, and 1,3,6-NTS at three different pH values. The results provided a simultaneous indirect photometric analysis of both anions and cations with detection limits ranging from 0.5 to 5 ppm for anions and from 10 to 15 ppm for cations with a total run time of under 7 min. The method was then applied to the analysis of Pyrodex^® RS and black powder, as well as several smokeless powders. The results obtained were consistent with previously reported results for separate anion and cation analysis and provide a faster, more complete analysis of each sample in a single chromatographic run.     

Gold nanomaterials based pseudostationary phases in capillary electrophoresis: A brand‐new attempt at chondroitin sulfate isomers separation

In this work, a CE method with bare gold nanorods (GNRs) based pseudostationary phase was developed and applied for the separation of chondroitin sulfate (CS) isomers, CS, and dermatan sulfate (DS). The separation efficiency was investigated by varying the experimental parameters such as concentration and pH of the BGE, separation voltage, internal diameter of capillary, different size, and morphology of gold nanomaterials. Results showed that different size and morphology of gold nanomaterials had different effects on the separation of CS and DS. The best separation of CS and DS was achieved in the BGE composed of aqueous 150 mmol/L (mM) ethylenediamine + 20 mM sodium dihydrogen phosphate + 30% v/v GNRs, pH 4.5, at the separation voltage of ?10 kV. Capillary was 59.2 cm in length (effective length 49 cm), 50 μm id capillary thermostated at 25°C. CE with bare GNRs used as pseudostationary phase was shown to be a suitable technique for the separation of CS and DS mixtures with wider peaks. RSD of migration time and peak area of CS and DS were 0.13, 0.14 and 0.86, 1.07%, respectively.     

Efficient and reproducible analysis of peptides by capillary electrophoresis using noncovalently bilayer-coated capillaries

The usefulness of a noncovalent capillary coating consisting of two layers of oppositely charged polymers for the separation of peptides with capillary electrophoresis (CE) was studied. Capillaries were coated simply by subsequently flushing with solutions of 1% m/v Polybrene and 1% v/v poly(vinylsulfonate) (PVS) forming a bilayer, which showed to produce a strong and highly reproducible electroosmotic flow (EOF) at low pH. Using this coating in combination with a background electrolyte (BGE) containing sodium phosphate (pH 2.5) and 0.01% v/v PVS, initially broadened and overlapping peaks were obtained for some test peptides. By omitting the PVS from the BGE, the peak width and shape of the peptides improved resulting in baseline separation. A systematic study of the influence of the BGE composition showed that considerable further enhancement of the separation efficiency was achieved by increasing the ionic strength of the BGE. Using a BGE of 200 mM tris(hydroxymethyl)aminomethane (Tris)-phosphate (pH 2.5) plate numbers for the peptides were in the 300 000-600 000 range and the relative standard deviation of the peptide migration times was less then 0.3% (n = 5). The use of Tris-phosphate instead of sodium phosphate allowed the current to stay within acceptable limits when 30 kV was used as separation voltage. Overall, the bilayer coating showed a remarkable EOF repeatability, as well as long-term stability. Compared to bare fused-silica capillaries the intraday and interday repeatability of migration times was very favorable and coated capillaries could be used for over a month performing analyses with low and high ionic strength BGEs without any performance deterioration. The usefulness of the bilayer-coated capillaries for the analysis of positively charged peptides was demonstrated by the fast and efficient separation of various closely related enkephalins and the baseline separation of an isomeric peptide/peptoid couple exhibiting efficiencies of over 550 000 plates.     

Co‐electroosmotic capillary electrophoresis of basic proteins with 1‐alkyl‐3‐methylimidazolium tetrafluoroborate ionic liquids as non‐covalent coating agents of the fused‐silica capillary and additives of the electrolyte solution

The paper reports the results of a study carried out to evaluate the use of three 1‐alkyl‐3‐methylimidazolium‐based ionic liquids as non‐covalent coating agents for bare fused‐silica capillaries and additives of the electrolyte solutions (BGE) for CE of basic proteins in the co‐EOF separation mode. The three ionic liquids are differentiated from each other by the length of the alkyl group on the imidazolium cation, consisting of either an ethyl, butyl or octyl substituent, whereas tetrafluoroborate is the common anionic component of the ionic liquids. Coating the capillary with the ionic liquid resulted in improved peak shape and protein separation, while the EOF was maintained cathodic. This indicates that each ionic liquid is effective at masking the protein interaction sites on the inner surface of the capillary, also when its adsorption onto the capillary wall has not completely neutralized all the negative charges arising from the ionization of the silanol groups and the ionic liquid is not incorporated into the BGE employed for separation. Using the coated capillaries with BGE containing the ionic liquid employed for the coating, at concentration low enough to maintaining the EOF cathodic, both peak shape and protein separation varied to different extents, based on the particular ionic liquid used and its concentration. Fast and efficient separation of the model basic protein mixture in co‐electroosmotic CE is obtained with the 1‐butyl‐3‐methylimidazolium tetrafluoroborate coated capillary and 100 mM acetate buffer (pH 4.0) containing 4.4 mM 1‐butyl‐3‐methylimidazolium tetrafluoroborate as the BGE.     

Principal component analysis and cluster analysis for the characterisation of marbles by capillary electrophoresis

Chemical characterisation has been carried out on 25 quarry marbles collected from Marmara, Aegean and Thrace regions of Turkey. Ten elements were determined by capillary electrophoresis (CE). Principal component analysis and cluster analysis techniques were utilised to define grouping of different marble samples. These techniques showed that the analysed marbles were differentiable mainly by provenance. Experimental conditions such as pH, applied voltage and concentration of α-hydroxyisobutyric acid (HIBA) were optimised to achieve the best separation of metal ions using central composite design. The optimum pH 3.7, applied voltage 15 kV and concentration of HIBA 10 mM were found to provide the best separation for all metal ions investigated.     

Determination of trace metals by capillary electrophoresis

A new analytical procedure is developed using a strong complexing agent, 1,10-phenanthroline (Phen), for direct UV detection of Zn, Mn, Cu, Co, Cd, and Fe at microg/L concentrations in environmental water samples. The metal chelates formed showed different electrophoretic mobilities and solved the comigration problem for capillary electrophoresis (CE) separation of free metal ions. To obtain stable metal-Phen chelates during the capillary zone electrophoresis (CZE) run, both pre-column and on-column complexation are required and threefold excess of Phen over metal ions should be added to the sample. The optimized background electrolyte (BGE) consists of 30 mM hydroxylamine hydrochloride and 0.1% methanol at pH 3.6. Under hydrodynamic sampling, CE run at + 20 kV in 65 cm x 0.05 mm ID fused-silica column with detection at 265 nm, baseline separation, satisfactory working ranges (10 microg/L to 5.5 mg/L), sensitive detection limits (1-3 microg/L), good repeatability for migration times (relative standard deviation, RSD 0.36-0.81%, n = 5), peak area (RSD 3.2-4.2%, n = 5) and peak height (RSD 3.2-4.5%, n = 5) were obtained for the metal cations investigated. The reliability of the method was established by parallel determination using the inductively coupled plasma-atomic emission spectrometry (ICP-AES) method giving results within statistical variation. The procedure developed is shown to provide a quick, sensitive, precise, and economic method for simultaneous determination of metal cations that can form stable chelates with Phen.     

Development of a gas diffusion probe for the rapid measurement of pCO2 in aquatic samples

A capillary electrophoresis (CE) procedure with contactless conductivity detection (C(4)D) has been developed for monitoring of neutral mono- and disaccharides in drinks and foodstuffs. The separation of a mixture of seven neutral saccharides (glucose, fructose, galactose, mannose, ribose, sucrose and lactose) employed a quartz capillary, 5 μm i.d., with an effective length of 18.3 cm, and 75 mM NaOH (pH 12.8) as the background electrolyte (BGE). The limit of detection (LOD) values obtained lied within a range from 0.4 μmol L(-1) for lactose to 0.9 μmol L(-1) for ribose, with a separation time shorter than 140 s. The procedure was successfully applied to determinations of saccharides in fruit juices, Coca-Cola, milk, red and white wines, yoghurts, honey and a foodstuff additive.     

Evaluation of amino acid ester‐based ionic liquids as buffer additives in CE for the separation of 2‐arylpropionic acids nonsteroidal anti‐inflammatory drugs

The aim of the present study is the CE performance evaluation for the separation of 2‐arylpropionic acid nonsteroidal anti‐inflammatory drugs. In particular, the separation of indoprofen, carprofen, ketoprofen, ibuprofen, and flurbiprofen was obtained by supporting the BGE either with SDS or an amino acid ester‐based ionic liquid (AAIL). The performance of these additives was evaluated by comparing migration times, efficiencies and %RSD values. The addition of the AAIL into the BGE provided baseline separation within 10 min, while in the case of SDS, the analytes eluted within 23 min. The optimum conditions involve a BGE of 100 mM Tris/10 mM sodium tetraboratedecahydrate (pH 8) and 40 mM l ‐alanine tert butyl ester lactate or 10 mM SDS and a temperature of 35°C for AAIL and 20°C for SDS. The run‐to‐run reproducibility was evaluated by computing the %RSD values of the EOF and the analyte peaks. When the AAIL was used, an excellent reproducibility was obtained, since all %RSD values were below 1.3%. On the contrary, the addition of SDS resulted in much higher RSD values (2.1–11.7%). The efficiency values of all analyte peaks were above 102 000 for l ‐AlaC₄Lac, in comparison to SDS, which provided efficiency values between 47000 and 76000. Finally, in an attempt to study the synergistic effect of SDS and AAIL, both additives were added into the BGE at concentrations of 10 and 40 mM, respectively. The results were similar to the ones obtained when SDS was used as the sole additive.     

Different strategies for the preconcentration and separation of parabens by capillary electrophoresis

Several strategies, namely, large volume sample stacking (LVSS), field‐amplified sample injection (FASI), sweeping, and in‐line SPE‐CE, were investigated for the simultaneous separation and preconcentration of a group of parabens. A BGE consisting of 20 mM sodium dihydrogenphosphate (pH 2.28) and 150 mM SDS with 15% ACN was used for the separation and preconcentration of the compounds by sweeping, and a BGE consisting of 30 mM sodium borate (pH 9.5) was used for the separation and preconcentration of the compounds by LVSS, FASI, and in‐line SPE‐CE. Several factors affecting the preconcentration process were investigated in order to obtain the maximum enhancement of sensitivity. The LODs obtained for parabens were in the range of 18–27, 3–4, 2, and 0.01–0.02 ng/mL, and the sensitivity evaluated in terms of LODs was improved up to 29‐, 77‐, 120‐, and 18 400‐fold for sweeping, LVSS, FASI, and in‐line SPE‐CE, respectively. These preconcentration techniques showed potential as good strategies for focusing parabens. The four methods were validated with standard samples to show the potential of these techniques for future applications in real samples, such as biological and environmental samples.     

Online concentration by field-amplified sample injection in acidic buffer for analysis of fangchinoline and tetrandrine in herbal medicine by flow injection-micellar electrokinetic capillary chromatography

A novel, rapid, and continuous online concentration approach based on field-amplified sample injection for the analysis of fangchinoline and tetrandrine was developed in this paper by combination of flow injection-MEKC. The BGE used was a solution composed of 75 mM H3PO4-triethylamine-2.5% v/v polyoxyethylene sorbitan monolaurate-20% v/v methanol buffer (pH* 5.0). The analytes prepared in 50% v/v aqueous ethanol were used as the test analytes. Sample was injected electrokinetically between plugs of water. When the cations reached the boundary between the water plug and BGE, they slowed down and became concentrated. Thereafter, MEKC was initiated for the separation. This results in 6.8-8.9-fold improvement in concentration sensitivity relative to conventional CE methods. The separation could be achieved within 10 min and sample throughput rate can reach up to 50/h. The repeatability (defined as RSD) was 4.8, 4.4% with peak height evaluation and 3.6, 0.94% with peak area evaluation for TET and FAN, respectively.     

Determination of free cyanide and zinc cyanide complex by capillary electrophoresis

A capillary electrophoretic (CE) protocol was developed for the separation and quantification of free cyanide and zinc cyanide complex, two key species in gold cyanidation of zinc-bearing sulfidic ores. Several common carrier electrolytes were implemented in an indirect UV detection method. The effect of electric field strength, injection volume, concentration of electro-osmotic flow (EOF) modifier and UV-absorbing agent in background electrolyte (BGE) was examined while peak height, peak area and noise were considered for optimization. The best results were obtained using a BGE that contained 35 mM sodium chromate, 12 mM free cyanide and 0.45 mM hexamethonium bromide at pH 10.5. Free cyanide concentration was compared to that measured with the conventional silver nitrate titration method in solutions containing free cyanides and weak cyano-complexes. The developed CE protocol proved very robust in capturing the concentration of free cyanides (4% error) unlike the titration method which exhibited substantial sensitivity to the interfering weak cyano-complexes (38% error).     

Fast and easy coating for capillary electrophoresis based on a physically adsorbed cationic copolymer

In this work, a new copolymer synthesized in our laboratory is used as physically adsorbed coating for capillary electrophoresis (CE). The copolymer is composed of ethylpyrrolidine methacrylate (EPyM) and methylmethacrylate (MMA). The capillary coating is easily obtained by simply flushing into the tubing an EPyM/MMA solution. It is demonstrated that the composition of the EPyM/MMA copolymer together with the selection of the background electrolyte (BGE) and pH allow tailoring the direction and magnitude of the electroosmotic flow (EOF) in CE. It is also shown that the EOF obtained for the EPyM/MMA-coated capillaries was reproducible in all cases independently on pH or polymer composition. Thus, RSD values lower than 1.9% (n=5) for the same capillary and day were obtained for the migration time, while the repeatability interdays (n=5) was observed to provide RSD values lower than 0.5%. The stability of the coating procedure was also tested between capillaries (n=3) obtaining RSD values lower than 0.6%. It is demonstrated with several examples that the use of EPyM/MMA coatings in CE can drastically reduce the analysis time and/or to improve the resolution of the separations. It is shown that EPyM/MMA-coated capillaries allow the separation of basic proteins by reducing their adsorption onto the capillary wall. Also, EPyM/MMA-coated capillaries provide a faster separation of samples containing simultaneously positive and negative analytes. Moreover, it is demonstrated that the use of EPyM/MMA-coated capillaries can incorporate an additional chromatographic-like interaction with nucleosides that highly improves the separation of this group of solutes.     

Use of chiral amino acid ester‐based ionic liquids as chiral selectors in CE

In this study, the applicability of a chiral ionic liquid (CIL) as the sole chiral selector in CE was investigated for the first time. In particular, five amino acid ester‐based CILs were synthesized and used as additives in the BGE in order to evaluate their chiral recognition ability. The performance of these CILs as the sole chiral selectors was evaluated by using 1,1′‐binaphthyl‐2,2‐diylhydrogenphosphate (BNP) as the analyte and by comparing the resolution values. Different parameters were examined, such as the alkyl group bulkiness and the configuration of the cation, the anion type of the CIL and its concentration, and the pH of the BGE, in order to optimize the separation of the enantiomers and to demonstrate the effect that each parameter has on the chiral‐recognition ability of the CIL. Baseline separation of BNP within 13 min was achieved by using a BGE of 100 mM Tris/10 mM sodium tetraboratedecahydrate (pH 8) and a chiral selector of 60 mM l ‐alanine tert butyl ester lactate. The run‐to‐run and batch‐to‐batch reproducibilities were also evaluated by computing the %RSD values of the EOF and the two enantiomer peaks. In both cases, very good reproducibilities were observed, since all %RSD values were below 1%.     

Determination of phenolic acids in olive oil by capillary electrophoresis

A CZE method for the separation and quantitation of phenolic acids (cinnamic, syringic, p-coumaric, vanillic, caffeic, 3,4-dihydroxyphenylacetic, protocatechuic), extracted from extra virgin olive oil, was developed. The sample preparation involved the LLE and SPE extraction methods. CE separation was performed in a fused silica capillary of I.D.= 50microm using as a BGE 40 mM borate buffer at pH=9.2. The separation voltage was 18kV with corresponding current of 27-28 microA. Detection was accomplished with UV-detector at lambda=200nm. The proposed method was fully validated. A good repeatability of migration time (RSD% ranged from 0.81 to 1.63) and of corrected peak area (RSD% from 2.89 to 5.77) was obtained. The linearity of detector response in the range from 5 to 50 ppm was checked, obtaining the correlation coefficient R2 values in the range: 0.9919-0.9997. Some phenolic acids in real oil samples were detected and quantified with the proposed method.     

A fast CE method for the achiral separation of methadone and its major metabolites, 2-ethylidene-1,5-dimethyl-3,3-diphenylpyrrolidine and 2-ethyl-5-methyl-3,3-diphenyl-1-pyrroline

The utilization of dynamic doubly coated capillaries for a fast separation of methadone and its two major metabolites, 2-ethylidene-1,5-dimethyl-3,3-diphenylpyrrolidine (EDDP) and 2-ethyl-5-methyl-3,3-diphenyl-1-pyrroline (EMDP) was investigated. The coated capillaries were prepared using a polycation of poly(diallyldimethylammonium chloride) and a polyanion of dextran sulfate. A fast achiral separation was developed using the coated capillaries with a BGE of 100 mM phosphate buffer at pH 2.6. Complete achiral separation of methadone, EDDP and EMDP was achieved, with migration times of approximately 4 min. The method offers considerable advantages with respect to BGE simplicity and analysis time compared to previously published CE methods for methadone and its related analytes.