Separation of <Superscript>113m</Superscript>In from <Superscript>113</Superscript>Sn based on activated carbon used as column matrix

The activated carbon was prepared by using corncobs and characterized by sorpatometer for using as an exchanger material to separate the generated ^113mIn from ¹¹³Sn and ^124,125Sb. To optimize the separation process, the different parameters like acetone percentage, HCl concentration were studied. The exchange capacity of Sn(IV) is 7.6 meq/g onto the activated carbon and the elution efficiency of ^113mIn > 80% by using 10 mL of 0.2 M HCl-80% acetone with flow rate 1 mL/min. The radionuclidic purity and radiochemical purity of the eluted ^113mIn were examined and clarified the presence of ^124,125Sb with relatively high level as radio impurities, so further separation was carried out by using Dowex 1×8 as an anion exchanger below the activated carbon matrix on the same separation column to adsorb the ¹¹³Sn and ^124,125Sb, which escape from the activated carbon matrix.     

Zirconium silicotungstate matrix as a prospective sorbent material for the preparation of <Superscript>113</Superscript>Sn/<Superscript>113m</Superscript>In generator

The zirconium silicotungstate (ZrSiW) was studied as an effective sorbent material to be used in the ¹¹³Sn/^113mIn generator. The results elucidated that the distribution coefficient of ¹¹³Sn (3700 mL/g) is greater than ^113mIn (275 mL/g) from 0.1 M HCl acid solution to the ZrSiW material. The maximum sorption capacity of Sn (IV) was found to be 33 mg per gram ZrSiW (~?0.3 mmol/g). The elution yield of ^113mIn was found to be >?78?±?6.4% with an acceptable purity of radionuclidic and radiochemical (≥?99.99 and 96.8%, respectively). The rigorous separation of ^113mIn from the ¹²⁵Sb was carried out due to its long half-life (2.758 years) and beta emission that causes tissue damage. Zr, W and Si levels are below the permitted limit in the ^113mIn eluate.     

Extraction chromatography for the separation of <Superscript>239</Superscript>Np from <Superscript>243</Superscript>Am

Summary An extraction chromatography method was developed for the separation of 239Np from ²⁴³Am in nitric acid solution. A sorbent based on aliphatic quaternary amine Aliquat-336 and hydrophobized silica gel was prepared. ²³⁹Np reduced to the oxidation state(IV) with ferrous sulfamate in 2M or 6M HNO₃ sorbs on the prepared silica gel column. After washing with 0.1M ferrous sulfamate in 2.5M HNO₃, ²³⁹Np is eluted with 0.1M HNO₃ containing 0.02M HF. The separation of ²⁴³Am from ²³⁹Np is very effective. The purity of ²³⁹Np was found to be better than 99.5%. The proposed ²³⁹Np milking procedure is suitable for the preparation of ²³⁹Np tracer that can be used for the determination of ²³⁷Np radiochemical yield.     

Extraction chromatographic separation of iron from complex liquid samples and the determination of <Superscript>55</Superscript>Fe

Summary Iron separation is described from liquid samples with a high concentration of ions that enables simple determination of ⁵⁵Fe. One of the described methods consists of iron precipitation from a large volume seawater by sodium hydroxide and/or ammonium carbonate and separation from other elements (Ca, Sr, Cu, Mg, etc.) on a TRU column with 4M HCl or 8M HNO₃. In the other procedure iron is separated directly from a mixture of seawater samples and HCl on a TRU column. In both methods, the iron recovery is almost 100%. After separation, ⁵⁵Fe is determined by counting with a liquid scintillation counter. The binding of Fe and Zn on TEVA, U/TEVA and TRU resins from seawater solutions of HCl and HNO₃depends on the type of the resin, concentration of acid and other ions. Iron and zinc can be separated from seawater on a U/TEVA column with 2M HCl.     

Ion-exchange studies of <Superscript>110m</Superscript>Ag(I) using synthetic inorganic ion-exchanger

In the present investigation, the selective adsorption of silver on synthetic inorganic ion exchanger, zinc(II) ferrocyanide, has been established by batch method, under specific conditions, using ^110mAg as a tracer. The efficiency of adsorption has been determined by γ-ray spectrometry and was found to be greater than 96%. The Ag(I) uptake by the exchanger has also been evaluated. The selectivity of the method was checked by studying the adsorption of Ag(I) in the presence of a number of foreign ions using their corresponding tracers. The interfering ions were removed by washing the ion-exchanger with appropriate reagents, so that it could be applied for the determination of trace amount of Ag(I) in complex matrices, containing trace amount of other metal ions.     

Simultaneous production and separation of no-carrier-added 111In, 109Cd from alpha particle induced silver target

A natural silver foil was bombarded by 30 MeV α-particles which produced ¹¹¹In, ¹⁰⁹Cd and ^106mAg in the target matrix. ¹¹¹In and ¹⁰⁹Cd were separated from the Ag target matrix employing ion-exchange chromatography and liquid–liquid extraction (LLX). In the chromatographic separation, the active solution containing the NCA products were adsorbed in the column containing Dowex 50 and were eluted with HNO₃. Bulk silver and ¹⁰⁹Cd were sequentially eluted with 1 M HNO₃. After complete elution of ¹⁰⁹Cd and the bulk, ¹¹¹In was eluted with 1.5 M HNO₃. In the LLX, the NCA ¹¹¹In was extracted to 1 % HDEHP (di-2(ethylhexyl)phosphoric acid) from 10^?2 M HNO₃ solution, leaving cadmium and bulk silver quantitatively in the aqueous phase. The NCA ¹⁰⁹Cd was separated from the bulk Ag by precipitating Ag as AgCl. NCA ¹¹¹In was stripped back quantitatively from HDEHP phase using 8 M HNO₃.     

<Superscript>137</Superscript>Cs/<Superscript>137m</Superscript>Ba radioisotope generator based on 6-tungstocerate(IV) column matrix

Summary Barium-137m radioisotope generator of the chromatographic column elution mode based on loading 1.5 g 6-tungstocerate(IV) gel matrix with ~54 kBq of fission-produced ¹³⁷Cs is described. The elution performance of the generated ^137mBa radionuclide was investigated as a function of chemical composition of the eluent, flow rate, elution frequency, and age of the generator system. At comparable conditions, ^137mBa eluates with 0.9% NaCl-0.1M HCl eluent had higher elution yields and radionuclidic purity than with 0.1M NH₄Cl-0.1M HCl eluent. The generator has been repeatedly eluted for 311 days by passing 4810 ml of the saline eluent (10 ml × 481 elution operations) at a flow rate of 3.0 ml/min. Barium-137m eluates of high and reproducible elution yields, chemical and radionuclidic purities of (≥ 99.99%) were obtained.     

Liquid — Liquid extraction of silver(I) by diphenyl-2-pyridylmethane in benzene from aqueous mineral acid — Thiocyanate solutions

Liquid — liquid extraction of Ag(I) by diphenyl-2-pyridylmethane (DPPM) in benzene from aqueous nitric and sulfuric acid solutions containing thiocyanate ions has been studied at ambient temperature (24±2 °C). The metal is extracted quantitatively from 0.01M HNO₃+0.02M KSCN; or 0.25M H₂SO₄+0.02M KSCN by 0.1M DPPM (optimum extraction conditions). Slope analysis indicates that two types of ion-pair complexes i.e. [(DPPMH)⁺·Ag(SCN) ₂ ^– ] and [(DPPMH) ₂ ⁺ ·Ag(SCN) ₃ ^2– ] are involved in the extraction process. Separation factors determined at optimum conditions reveal the separation of Ag(I) from Cs(I), Br(I), Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Cd(II), Fe(III), Au(III) (from HNO₃ solution only), Cr(III), Hf(IV), Ta(V), Sn(IV) and Cr(VI). With the exception of thiosulfate, other complexing anions like ascorbate, acetate, citrate, oxalate do not hinder the extraction of Ag(I) under optimum conditions.     

Combined determination of <Superscript>99</Superscript>Tc and <Superscript>108m</Superscript>Ag in L/ILW liquid wastes

The low- and intermediate-activity level liquid wastes produced by the Paks Nuclear Power Plant (NPP) contain routinely measureable gamma-emitting (e.g., ⁵⁴Mn, ⁶⁰Co, ^110mAg, and ¹³⁷Cs) as well as many so-called “difficult-to-measure” radionuclides. Despite of their low specific activity compared to the total, the reliable determination of these radionuclides is an important issue of nuclear waste management. The increasing amount of waste samples to be qualified yearly by our laboratory put a pressure on revising the existing procedure of ⁹⁹Tc separation applied. We have managed to halve the initial amount of the sample required to achieve the same level of detection of technetium. Furthermore, one of the new purifying steps introduced have proved to be able to separate ^108mAg (and ^110mAg) better than 99% keeping the ⁹⁹Tc content of the product almost intact. Means of separation of ⁹⁹Tc from ¹⁰⁶Ru and ^124+125Sb have also been successfully investigated. As intended, this new procedure has a major impact on the chemical reagent as well as the electricity requirement of the separation making it more cost-effective.     

Preparation of <Superscript>95m</Superscript>Tc radiotracer

Several procedures for preparation of the ^95mTc radiotracer following irradiation of a thin Mo target with deuterons were tested. The procedures consisting of alkaline-oxidative fusion of the irradiated target in a mixture of Na₂O₂ + NaOH and subsequent liquid–liquid extraction with 2-butanone, and acid decomposition of the target in a mixture of H₂SO₄ + HNO₃ followed by extraction chromatography with PAN-Aliquat 336 composite material appeared suitable for the given purpose.     

Cation-exchange separation of uranium from thorium in nitric acid medium</p> </p>

Summary Sorption behavior of Th and U on cation-exchange resins was investigated from nitric acid medium by both batch and column methods. The cation-exchange studies involved the sorption of UO₂²⁺ and Th⁴⁺ and their cationic complexes onto Dowex 50Wx8 and Dowex 50Wx4 resins (50-100 mesh). The batch data yielded a separation factor (K_d,Th/K_d,U) value of >100 for the cation-exchanger, Dowex 50Wx4 at 1-2M HNO₃. Separation of uranium from thorium was also carried out by column method in nitric acid medium using cation-exchangers, Dowex 50Wx4 as well as Dowex 50Wx8. While uranium elution was possible at 1M HNO₃, Th could be eluted only at higher concentration of nitric acid (>6M). The stripped solution emanating from a mixer settler employing di-2-ethyl hexyl isobutyramide as extractant and feed solution similar to THOREX process comprising 350 mg/l U and 380 mg/l Th in 0.75M HNO₃ was loaded on the column and the decontamination factor value for U in the product was >1000.</p> </p>     

Radiochemical separation of110mAg,210Pb,127Te and131I from aqueous nitric acid solution by bis-2-(butoxyethyl ether)

A bis-2-(butoxyethyl ether) (DBC) solvent extraction method has been developed for the radiochemical separation of^110mAg,²¹⁰Pb,¹²⁷Te and¹³¹I in varying concentrations of aqueous HNO₃. Various factors were examined to determine the optimum conditions of extraction. The effect of various masking agents has been studied. The extraction of¹³¹I is enhanced to 99% at 2.4M HNO₃ in the presence of KSCN.¹³¹I was stripped into aqueous sodium hydroxide from the oxygenated organic extractant. The method was then applied for the recovery of¹³¹I from neutron irradiated tellurium metal. The mechanism and reactivity of DBC with metal ions is described.     

Systematic radiochemical separation for the determination of <Superscript>99</Superscript>Tc, <Superscript>90</Superscript>Sr, <Superscript>94</Superscript>Nb, <Superscript>55</Superscript>Fe and <Superscript>59,63</Superscript>Ni in low and intermediate radioactive waste samples

A simple and rapid separation procedure was systemized for the determination of ⁹⁹Tc, ⁹⁰Sr, ⁹⁴Nb, ⁵⁵Fe and ^59,63Ni in low and intermediate level radioactive wastes. The integrated procedure involves precipitation, anion exchange and extraction chromatography for the separation and purification of individual radionuclide from sample matrix elements and from other radionuclides. After separating Re (as a surrogate of ⁹⁹Tc) on an anion change resin column, Sr, Nb, Fe and Ni were sequentially separated as follows; Sr was separated as Sr (Ca-oxalate) co-precipitates from Nb, Fe and Ni followed by purification using Sr-Spec extraction chromatographic resin. Nb was separated from Fe and Ni by anion exchange chromatography. Fe was separated from Ni by anion exchange chromatography. Ni was separated as Ni-dimethylglyoxime precipitates after the removal of ^134,137Cs and ^110mAg by Cs-phosphotungstate and AgCl precipitation, respectively. Finally, the radionuclide sources were prepared by precipitation for their radioactivity measurements. The reliability of the procedure was evaluated by measuring the recovery of chemical carriers added to a synthetic radioactive waste solution.     

Separation of radioarsenic from irradiated germanium oxide targets for the production of <Superscript>71</Superscript>As and <Superscript>72</Superscript>As

A method for the separation of no-carrier-added arsenic radionuclides from the bulk amount of proton-irradiated GeO₂ targets as well as from coproduced radiogallium was developed. The radionuclides ⁶⁹Ge and ⁶⁷Ga produced during irradiation of GeO₂ were used as tracers for Ge and Ga in the experiments. After dissolution of the target the ratio of As(III) to As(V) was determined via thin layer chromatography (TLC). The extraction of radioarsenic by different organic solvents from acid solutions containing alkali iodide was studied and optimized. The influence of the concentration of various acids (HCl, HClO₄, HNO₃, HBr, H₂SO₄) as well as of KI was studied using cyclohexane. The optimum separation of radioarsenic was achieved using cyclohexane with 4.75 M HCl and 0.5 M KI and its back-extraction with a 0.1% H₂O₂ solution. The separation leads to high purity radioarsenic containing no radiogallium and <0.001% [⁶⁹Ge]Ge. The overall radiochemical yield is 93 ± 3%. The practical application of the optimized procedure in the production of ⁷¹As and ⁷²As is demonstrated and batch yields achieved were in the range of 75–84% of the theoretical values.     

Separation of <Superscript>133</Superscript>Xe from <Superscript>99</Superscript>Mo, <Superscript>131</Superscript>I and uranium,and removal of impurities using gas chromatography

Summary Separation and purification of ¹³³Xe from acidic solution containing uranium, ⁹⁹Mo and ¹³¹I has been developed. In the first step of this work, uranium pellets were dissolved under pressure (8-15 bar) in 8M nitric acid solution. Then¹³³ Xe and other gases were conducted to activated charcoal cold trap. Final purification of ¹³³Xe from impurities such as NO_x, radioiodine and krypton was performed by passing through a molecular sieve preparative chromatographic column using helium as mobile phase. The final recovery of ¹³³Xe from the separation-purification process was higher than 98%. Adsorption-desorption behavior of radioxenon on the charcoal and molecular sieves have also been studied and discussed.     

Preparation and characterization of an extraction chromatography column for technetium separation based on Aliquat-336 and silica gel support

An extraction chromatographic material based on Aliquat-336 anchored on hydrophobized silica gel support was prepared as an ion exchanger. The prepared material appeared to be suitable for the separation of ⁹⁹Tc from environmental matrices in column application. The properties of the material, sorption characteristic and distribution coefficient of ^99mTcO₄ ^-in various media were studied. The prepared sorbent was conditioned by washing with nitric acid. The solution containing ^99mTcO₄ ^- in 0.1M HNO₃ was passed through the column. Tc was eluted from the column by 8M HNO₃. The flow rate was 0.4 ml/min. The chemical yield of technetium during the separation process was determined using ^99mTc tracer and gamma measurement. The sorption recovery of Tc from the prepared sorbent with 0.1M HNO₃ solution was more than 98%, and the desorption recovery from the column using 8M HNO₃ varied between 92-96%. It was found that the prepared sorbent is suitable for the separation of technetium from environmental matrices and radioactive wastes. This revised version was published online in July 2006 with corrections to the Cover Date.     

Use of organophosphorus extractants impregnated on silica gel for the extraction chromatographic separation of minor actinides from high level waste solutions

Silica-gel has been used as an inert support for the extraction chromatographic separation of actinides and lanthanides from HNO₃ and synthetic high level waste (HLW) solutions. Silica-gel was impregnated with tri-butyl phosphate (TBP), to yield STBP; 2-ethylhexyl phosphonic acid, mono 2-ethylhexyl ester (KSM-17, equivalent to PC-88A), SKSM; octyl(phenyl)-N,N-diisobutyl carbamoylmethylphosphine oxide (CMPO), SCMPO; and trialkylphosphine oxide (Cyanex-923), SCYN and sorption of Pu(IV), Am(III) and Eu(III) from HNO₃ solutions was studied batchwise. Several parameters, like time of equilibration, HNO₃ and Pu(IV) concentrations were varied. The uptake of Pu(IV) from 3.0M HNO₃ followed the order SCMPO>SCYN>SKSM>STBP. With increasing HNO₃ concentration, D _Pu increased up to 3.0M of HNO₃ for STBP, SKSM and SCMPO and then decreased. In the case of Am and Eu with SCMPO, the D values initially increased between 0.5 to 1.0M of HNO₃, remained constant up to 5.0M and then slightly decreased at 7.5M. Also, the effects of NaNO₃, Nd(III) and U(VI) concentrations on the uptake of Am(III) from HNO₃ solutions were evaluated. With increasing NaNO₃ concentration up to 3.0M, D _Am remained almost constant while it was observed that it decreases drastically by adding Nd(III) or U(VI). The uptake of Pu and Am from synthetic pressurized heavy water reactor high level waste (PHWR-HLW) in presence of high concentrations of uranium and after depleting the uranium content, and finally extraction chromatographic column separation of Pu and Am from U-depleted synthetic PHWR-HLW have been carried out. Using SCMPO, high sorption of Pu, Am and U was obtained from the U-depleted HLW solution. These metal ions were subsequently eluted using various reagents. The sorption results of the metal ions on silica-gel impregnated with several phosphorus based extractants have been compared. The uptake of Am, Pu and rare earths by SCMPO has been compared with those where CMPO was sorbed on Chromosorb-102, Amberchrom CG-71 and styrene divinylbenzene copolymer immobilized in porous silica particles.     

The interaction of <Superscript>99m</Superscript>Tc with pyrimidine compounds

The reaction of ^99mTc of different oxidation states (+7, +4) with 2-thiouracil and 5-nitrobarbituric acid have been studied at different temperatures, pH and concentrations. The reaction mixtures have been analyzed at different times using thin layer chromatography (TLC) and a radio detector to show the peaks at the plates. ^99mTc is obtained from the Mo generators with oxidation state (+7). The use of SnCl₂ as a reducing agent gave ^99mTc with oxidation state (+4). It is very difficult to separate the complexes formed from the reactions in very small concentration. The percentage of ^99mTc and its oxidation state involved in the complexes can be determined. The labeling efficiencies (percentage of complex) in the reaction of ^99mTc⁺⁷ with 5-nitro-barbituric-acid increases mostly at pH  10. Both oxidation states of ^99mTc(+7, +4) can be detected at pH’s 4 and 10, but at pH  4, the reduced form ^99mTCO₂, is more pronounced. At pH  7 no complexes were detected and most of ^99mTc remains as ^99mTCO₄ ⁻ . By increasing the ligand concentration, the labeling efficiencies of the complex increases. For the reaction of ^99mTc of oxidation states (+4, +7) with 2-thiouracil at different temperatures and analytical times it is concluded that several complexes with different R_f values were observed in equilibrium and most of these complexes were unstable.     

A novel electrochemical <Superscript>99</Superscript>Mo/<Superscript>99m</Superscript>Tc generator

A novel electrochemical process to avail clinical grade ^99mTc from (n,γ)⁹⁹Mo has been demonstrated. The electrochemical parameters were optimized to maximize the ^99mTc yield with minimal ⁹⁹Mo contamination. ⁹⁹Mo/^99mTc generators containing up to 29.6 GBq (800 mCi) ⁹⁹Mo were developed and their performance were extensively evaluated for 10 days without changing the operating conditions. Very high radioactive concentration of ^99mTcO₄ ⁻ of acceptable quality, commensurate with hospital radiopharmacy requirements could be availed from the system with >90% yield. The compatibility of the product for the formulation of ^99mTc labeled radiopharmaceuticals such as ^99mTc-DMSA and ^99mTc-EC was found to be satisfactory in terms of high labeling yields. The proposed route represents an important step for enhancing the scope of accessing clinical grade ^99mTc from low specific activity (n, γ)⁹⁹Mo.     

<Superscript>103</Superscript>Ru/<Superscript>103m</Superscript>Rh generator

^103mRh is a very promising radionuclide for Auger electron therapy due to its very low photon/electron ratio. The goal of the present work was the elaboration a method for production of large quantities of ^103mRh for generator system. It was found that the combination of solvent extraction with evaporation of ¹⁰³RuO₄ followed by decomposition of H₅IO₆ makes it possible to produce ^103mRh of high radionuclidic and chemical purity.