Stability of Zn–Ni–TiO<Subscript>2</Subscript> and Zn–TiO<Subscript>2</Subscript> nanocomposite coatings in near-neutral sulphate solutions

Zn–Ni–TiO₂ and Zn–TiO₂ nanocomposites were prepared by galvanostatic cathodic square wave deposition. X-ray diffraction analysis and scanning electron microscopy revealed that the occlusion of TiO₂ nanoparticles (spherical shaped with diameter between 19.5 and 24.2 nm) promotes the formation of the γ-Ni₅Zn₂₁ phase, changes the preferred crystallographic orientation of Zn from (101) and (102) planes to (002), and decreases the particle size of the metallic matrices. The stability of the nanocomposites immersed in near-neutral 0.05 mold m⁻³ Na₂SO₄ solution (pH 6.2) was investigated over 24 h. The initial open circuit potential for the Zn–Ni–TiO₂ and Zn–TiO₂ coatings were −1.32 and −1.51 V (vs. Hg/Hg₂SO₄), respectively, and changed to −1.10 and –1.49 V (vs. Hg/Hg₂SO₄) after 24 h of immersion. Data extracted from the steady state polarization curves demonstrated that the metal–TiO₂ nanocomposites have, with respect to the metal coatings, a higher corrosion potential in the case of the Zn–Ni alloy composite; a lower corrosion potential in the case of Zn-based nanocomposite albeit the predominant (002) crystallographic orientation; and a lower initial corrosion resistance due to the smaller grain size and higher porosity in the Zn–Ni–TiO₂ and Zn–TiO₂ nanocomposites. Morphological and chemical analyses showed that a thicker passive layer is formed on the surface of the Zn–Ni–TiO₂ and Zn–TiO₂ deposits. After 24 h of immersion in the sulphate solution, the Zn–Ni–TiO₂ coating has the highest corrosion stability due to the double-protective action created by the deposit’s surface enrichment in Ni plus the higher amount of corrosion products.     

Elastic properties of TeO<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Ag<Subscript>2</Subscript>O glasses

A series of glasses [(TeO₂) _x (B₂O₃)_1−x ]_1−y [Ag₂O] _y with x = 70 and y = 10, 15, 20, 25 and 30 mol% were synthesised by rapid quenching. Longitudinal and shear ultrasonic velocity were measured at room temperature and at 5 MHz frequency. Elastic properties, Poisson's ratio, microhardness, softening temperature and Debye temperature have been calculated from the measured density and ultrasonic velocity at room temperature. The experimental results indicate that the elastic constants depend upon the composition of the glasses and the role of the Ag₂O inside the glass network is discussed. Estimated parameters based on Makishima–Mackenzie theory and bond compression model were calculated in order to analyse the experimental elastic moduli. Comparison between the experimental elastic moduli data obtained in the study and the calculated theoretically by the mentioned above models has been discussed.     

Microwave dielectric properties of the 5.5Li<Subscript>2</Subscript>O–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>–7TiO<Subscript>2</Subscript> ceramics

A new Li₂O–Nb₂O₅–TiO₂ (LNT) ceramic with the Li₂O:Nb₂O₅:TiO₂ mole ratio of 5.5:1:7 was prepared by solid state reaction route. The phase and structure of the ceramic were characterized by X-ray diffraction and scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The microwave dielectric ceramic has low sintering temperature (∼1075°C) and good microwave dielectric properties of ε _r=42, Q×f=16900 GHz (5.75 GHz), and τ _f =63.7 ppm/°C. The addition of B₂O₃ can effectively lower the sintering temperature from 1075 to 875°C and does not induce degradation of the microwave dielectric properties. Obviously, the LNT ceramics can be applied to microwave low temperature-cofired ceramics (LTCC) devices.     

Characterization and transport properties of 10BaO–xAg<Subscript>2</Subscript>O–(85-x)V<Subscript>2</Subscript>O<Subscript>5</Subscript>–5TeO<Subscript>2</Subscript> glass system

Silver-based quaternary glasses were prepared by splat quenching technique. X-ray diffraction and differential scanning calorimetry were done for confirming their amorphous nature. The conductivity of the glasses was measured in the frequency range from 1 Hz to 32 MHz from room temperature to 373 K. Conductivity data, which obeys the Arrhenius type behavior, shows minimum at 30 mol% Ag₂O, suggesting that the conductivity mechanisms are different above and below these two regions. The minimum in conductivity is accompanied by an inverse behavior of activation energy. Experimental data suggests that a polaron hopping mechanism operates in the electronically conducting domain of 20 ≤ × ≤ 30, and an interstitial pair mechanism operates in the ionically conducting domain of 35 ≤ × ≤ 55.     

Phase formation in the BaCO<Subscript>3</Subscript>–PbO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Features of the formation of lead-ferroniobate compounds in the xBaCO₃–(1 – x)PbO–Fe₂O₃–Nb₂O₅ system by solid-phase synthesis are investigated. For perovskite-type lead-ferroniobate solid solution, a single-phase concentration region is revealed at 1233 K. The crystalline structures of the synthesized compounds are refined using Rietveld analysis and the Pm3?m and R3m space groups. Ceramic samples of lead ferroniobate are studied by scanning electron microscopy.     

Electrochemical behavior of silicon compound in LiF–NaF–KF–Na<Subscript>2</Subscript>SiF<Subscript>6</Subscript> molten salt

The electrochemical reduction and nucleation process of Si⁴⁺ on an electrical steel electrode in the eutectic LiF–NaF–KF molten salt were investigated at 750 °C, by means of cyclic voltammetry and chronoamperometry technique. Silicon was electrodeposited on steel, and Fe₃Si was formed by the diffusivity of silicon on the electrode surface. The electrochemical reduction of Si⁴⁺ process in single-step charge transfer and the cathode process was reversible. The electrocrystallization process of silicon is controlled by progressive three-dimensional mechanism. The diffusion coefficient was calculated to be 5.42 × 10⁻⁷ cm²/s by chronopotentiometry at experimental conditions.     

Resistive switching behavior in a Ni–Ag<Subscript>2</Subscript>Se–Ni nanowire

Hysteretic resistive switching behavior in a silver selenide (Ag₂Se) nanowire, which had a diameter of about 200 nm and a length of about 10 μm, was studied using scanning probe microscopy. Electrical current measurements were carried out in a range from 0 to −10 V and in temperatures below and above the phase transition of Ag₂Se. ON/OFF switching times were measured with pulsed voltages. They displayed different characteristics at low and high temperatures. The results confirm that Ag₂Se nanowires have applications in nanoscale switching devices.     

Deep metastable eutectic nanometer-scale particles in the MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> system

Laboratory vapor phase condensation experiments systematically yield amorphous, homogeneous, nanoparticles with unique deep metastable eutectic compositions. They formed during the nucleation stage in rapidly cooling vapor systems. These nanoparticles evidence the complexity of the nucleation stage. Similar complex behavior may occur during the nucleation stage in quenched-melt laboratory experiments. Because of the bulk size of the quenched system many of such deep metastable eutectic nanodomains will anneal and adjust to local equilibrium but some will persist metastably depending on the time–temperature regime and melt/glass transformation.     

Synthesis and Gas-Sensing Properties of MnO2 – x and MnO2 – x/CuO-Coated Multiwalled Carbon Nanotube Nanocomposites

Physics of the Solid State - Nanocomposites based on multiwall carbon nanotubes (MWCNTs) impregnated with manganese oxide MnO2&nbsp;–&nbsp;x and copper oxide CuO are synthesized and...     

Size-controllable synthesis of functional heterostructured TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> core–shell nanoparticles

Mono and bicomponent TiO₂ and WO₃ nanoparticles were synthesized inside Vycor^® glass pores, by cycles of impregnation of the glass with the respective oxide precursor followed by its thermal decomposition. The impregnation-decomposition cycle (IDC) methodology promoted a linear mass increase of the glass matrix, and allowed tuning the nanoparticle size. X-ray diffraction and Raman spectroscopy data allowed identifying the formation of TiO₂ as anatase phase, while WO₃ is a mixture of the γ-WO₃ (monoclinic) and δ-WO₃ (triclinic) phases. High resolution transmission electron microscopy images revealed that for 3, 5, and 7 IDC, the TiO₂ nanoparticles obtained presented average diameters of 3.4, 4.3, and 5.1 nm, and the WO₃ nanoparticles have 2.9, 4.6, and 5.7 nm sizes. These TiO₂ and WO₃ monocomponent nanoparticles were submitted to IDC with the other oxide precursor, resulting in bicomponent nanoparticles. The broadening and shift of the Raman bands related to titanium and tungsten oxides suggest the formation of hetero-structure core–shell nanoparticles with tunable core sizes and shell thicknesses.     

A novel core–shell nanocomposite Ni–Ca@mSiO<Subscript>2</Subscript> for benzophenone selective hydrogenation

A novel core–shell nanocomposite Ni–Ca@mSiO₂ was first prepared by a modified Stöber method in this paper. It has a core–shell structure with Ni (about 8 nm in diameter) and Ca as the cores and mesoporous silica as the outer shell, as proven by the transmission electron microscopy. This nanocomposite exhibited good catalytic performance in the selective hydrogenation of benzophenone, with 96.1% conversion and 94.9% selectivity for benzhydrol under relatively mild reaction conditions. It was demonstrated that addition of small amounts of alkaline Ca can not only markedly improve the dispersion of the active species but also tune the acid–base property of this nanocomposite, resulting in the efficient suppression of benzhydrol dehydration to achieve a high selectivity. Furthermore, the core–shell nanocomposite Ni–Ca@mSiO₂ can be recycled four runs without appreciable loss of its initial activity, more stable than the traditional supported nanocatalyst Ni–Ca/mSiO₂. It was suggested that the outer mesoporous silica shell of Ni–Ca@mSiO₂ can prevent both the aggregation and the leaching of the active Ni species, accounting for its relatively good stability.

Open image in new window

Graphical abstract A magnetic core–shell nanocomposite Ni–Ca@mSiO₂ exhibited good activity, selectivity, and reusability in benzophenone selective hydrogenation.

     

AC Conductivity,XRD and transport properties of melt quenched PbI<Subscript>2</Subscript>–Ag<Subscript>2</Subscript>O–Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Composite materials used for electrode and electrolyte materials have been intensely studied in view of their advantages such as higher conductivity and better operational performance compared to their single-phase counterparts. The present work aims at studying the electrical and structural characteristics of a new composite electrolyte namely, (PbI₂) _x  − (Ag₂O–Cr₂O₃)_100−x where x = 5, 10, 15, 20, and 25 mol%, respectively, prepared by the melt quenching technique. The room temperature X-ray diffraction spectra revealed certain crystalline phases in the samples. AC conductivity analysis for all the prepared samples was carried out over the frequency range 1 MHz–20 Hz and in the temperature window 297–468 K. The room temperature conductivity values were calculated to be in the order of 10⁻⁵–10⁻³ Scm⁻¹. An Arrhenius dependence of temperature with conductivity was observed, and the activation energies calculated were found to be in the range 0.27–0.31 eV. Furthermore, the total ionic transport number (t _i) values obtained for all these indicated the ionic nature of this system. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

The development of the physical and electrical characteristics of multi-layer TiO<Subscript>2</Subscript>–W–TiO<Subscript>2</Subscript> thin films

In this study, two different thin films, TiO₂ thin film and TiO₂–W–TiO₂ multi-layer thin films (W, tungsten), are prepared by RF magnetron sputtering onto glass substrates. The crystal structure, morphology, and transmittance of TiO₂ and TiO₂–W–TiO₂ multi-layer thin films are investigated by X-ray diffraction, SEM, and UV-Vis spectrometer, respectively. The amorphous, rutile, and anatase TiO₂ phases are observed in the TiO₂ thin film and in the TiO₂–W–TiO₂ multi-layer thin films. The deposition of tungsten as the inter-layer will have large effect on the transmittance and phase ratios of rutile and anatase phases in the TiO₂–W–TiO₂ multi-layer thin films. The crystal intensities of amorous TiO₂ will decrease as the tungsten is used as the middle layer in the multi-layer structure. The band gap energy values of TiO₂ thin film and TiO₂–W–TiO₂ multi-layer thin films are evaluated from (αhν)^1/2 versus energy plots, and the calculated results show that the energy gap decreases from 3.21 eV (TiO₂ thin film) to 3.08∼3.03 EV (TiO₂–W–TiO₂ multi-layer thin films).     

Influence of Matrix Nature on the Structural Characteristics of In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CeO<Subscript>2</Subscript> and SnO<Subscript>2</Subscript>–CeO<Subscript>2</Subscript> Composites Fabricated by the Impregnation Method

The structural characteristics, valence states, and distribution of cerium ions between the components in In₂O₃–CeO₂ and SnO₂–CeO₂ nanocomposites fabricated using the impregnation method were studied. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were used to show that, during impregnation, cerium ions are not included into In₂O₃ crystals and are disposed only on their surface in the form of nano-sized crystallites or amorphous clusters. On the other side, under the contact of CeO₂ clusters with a surface of SnO₂ matrix crystals, cerium ions penetrate into the surface layer of these crystals. In contrast to an In₂O₃–CeO₂ system, where the addition of CeO₂ does not affect the conduction activation energy, where cerium oxide is added to SnO₂, the observed increase in the resistance of a SnO₂–CeO₂ composite is accompanied by a sufficient increase in activation energy. These data and the XPS spectra confirm the modification of the surface layers of conductive SnO₂ crystals as, a result of the penetration of cerium ions into these layers.     

Magnetic and magnetoresistive properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sr<Subscript>2</Subscript>FeMoO<Subscript>6–δ</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoheterostructures

A method has been developed for fabricating nanoporous matrices based on anodic aluminum oxide for the deposition of ferromagnetic nanoparticles in them. The modes of deposition of strontium ferromolybdate thin films prepared by the ion-plasma method have been worked out, and the magnetic and magnetoresistive properties, structure, and composition of the films have been investigated. It has been revealed that the microstructure and properties of the strontium ferromolybdate films deposited by ionplasma sputtering depend on the deposition rate and the temperature of the substrate. Based on the measurement of the electrical resistivity of nanoheterostructures in a magnetic field, it has been found that the magnetoresistance reaches 14% at T = 15 K and B = 8 T, which is due to the manifestation of tunneling magnetoresistance.     

Sol–gel synthesis and characterization of Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite solid electrolytes

Composite solid electrolytes in the system (1???x)Li₂CO₃–xAl₂O₃, with x?=?0.0–0.5 (mole), were synthesized by a sol–gel method. The synthesis carried out at low temperature resulted in voluminous and fluffy products. The obtained materials were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy/energy-dispersive X-ray, Fourier transform infrared spectroscopy and AC impedance spectroscopy. Structural analysis of the samples showed an amorphous feature of Li₂CO₃ and traces of α-LiAlO₂, γ-LiAlO₂ and LiAl₅O₈. The prepared composite samples possess high ionic conductivities at 130–180 °C on account of the presence of lithium aluminates as well as the formation of a high concentration of an amorphous phase of Li₂CO₃ via this sol–gel preparative technique.     

Effect of mixed glass formers on the crystallization kinetics in AgI–Ag<Subscript>2</Subscript>O–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–MoO<Subscript>3</Subscript> glassy superionic system

The crystallization and glass transition kinetics using differential scanning calorimetry (DSC) in 50AgI–33.33Ag₂O–16.67[(V₂O₅)_1−x –(MoO₃) _x ] superionic glassy system is discussed. Thermal stability of glass, studied using various criteria, does not vary significantly with glass former variation. However, the activation energies for structural relaxation (E _s) at glass transition temperature and crystallization (E _c) obtained using Moynihan and Kissinger, Matusita-Sakka formulations found to exhibit interesting trends with MoO₃ substitution in the glass matrix. It is noticed that the electrical conductivity (σ)–temperature (T) cycles obtained at a typical heating rate of 1 °C/min do exhibit significant thermal events. The conductivity after first heating cycle at room temperature is found to be increasing with MoO₃ content and maximum for x = 0.3 (~10⁻³ Ω⁻¹ cm⁻¹ at 30 °C) which is comparable to that of the host 50AgI–33.33Ag₂O–16.67V₂O₅ glassy system. The parameters obtained from σ–T plots and DSC scans do complement each other in a particular range of composition.     

Electrooptical effect in the plasmon structure glass–In<Subscript>2</Subscript>O<Subscript>3</Subscript>: Sn–ferroelectric–Al with a subwavelength grating

We have constructed the equations of state for crystalline boron carbide B₁₁C (C–B–C) and its melt under high dynamic and static pressures. A kink on the shock adiabat for boron carbide has been revealed in the pressure range near 100 GPa, and the melting curve with negative curvature in the pressure range 0–120 GPa has been calculated. The results have been used for interpreting the kinks on the shock adiabat for boron carbide in the pressure range of 0–400 GPa.     

Recrystallization and formation of spheroidal gold particles in amorphous-like AlN–TiB<Subscript>2</Subscript>–TiSi<Subscript>2</Subscript> coatings after annealing and subsequent implantation

The recrystallization of the structure of an X-ray amorphous AlN–TiB₂–TiSi₂ coating containing short-range order regions with characteristic sizes of 0.8–1.0 nm has been performed using a negative gold ion (Au^–) beam and high-temperature annealing. Direct measurements using methods of high-resolution transmission electron microscopy (HRTEM) and energy-dispersive X-ray spectral (EDXS) microanalysis have demonstrated that thermal annealing at a temperature of 1300°C in air results in the formation of nanoscale (10–15 nm) phases AlN, AlB₂, Al₃O₃, and TiO₂, whereas the ion implantation of negative ions Au^– leads to a fragmentation (decrease in the size) of nanograins to 2–5 nm with the formation of spheroidal gold nanocrystallites a few nanometers in size, as well as to the formation of an amorphous oxide film in the depth (near-surface layer) of the coating due to ballistic ion mixing and collision cascades.     

Study of phase transition of TiO<Subscript>2</Subscript>–CaO system

Electrical conductivity of TiO₂ doped with CaO has been measured at different temperatures for various molar ratios. The conductivity after initially remaining constant till about 140 °C increases with temperature due to the migration of vacancies created by doping. After attaining a maximum value at 240 °C, conductivity decreases due to the collapse of fluorite framework. A second rise in conductivity at high temperature beyond 400 °C indicates the phase transition of TiO₂, from anatase to rutile, which is confirmed by the differential scanning calorimetry results. X-ray powder diffraction, impedance measurements, and Fourier transform infrared spectral studies were also carried out for confirming the doping effect and phase transitions in TiO₂. Doping of TiO₂ with CaO shifts the transition to lower temperatures.