Effect of protonation and deprotonation on surface charge density of Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>

The protonation and deprotonation of the Nb₂O₅ surface has been followed in order to understand the reactions of surface of this catalyst. The simultaneous potentiometric and conductometric titrations had been carried by using 50 mL of water suspension of Nb₂O₅ 40 g L⁻¹. The oxide was entirely deprotonated when adding 0.4 mL NaOH 1 mol L⁻¹, and later titrated with 0.1 mol L⁻¹. The titration had supplied K ₁ and K ₂ and the obtained values were 3.24 × 10⁻³ and 4.17 × 10⁻⁸, respectively. The zero point charge was pH_pcz = 4.94. The thermodynamic studies were carried out by using 50 mL of a 40 g/L Nb₂O₅ aqueous suspension with the pH adjusted to pH_PZC value. The suspension was titrated with 0.5 mol/L of HNO₃ or NaOH for protonation or deprotonation studies, respectively, in an isoperibol calorimeter CSC ISC-4300. Thus, the obtained thermodynamic values of the protonation and deprotonation of Nb₂O₅ were Δ_dp G = −37.60 kJ/mol, Δ_dp H = −23.72 kJ/mol and Δ_dpS = 47 J/(mol K).     

Electrocatalytic oxidation of pyridoxine (vitamin B<Subscript>6</Subscript>) on aluminum electrode modified by metallic palladium particles/iron (III) hexacyanoferrate (II) film

The electrocatalytic activity of a Prussian blue (PB) film on the aluminum electrode by taking advantage of the metallic palladium characteristic as an electron-transfer bridge (PB/Pd–Al) for electrooxidation of 2-methyl-3-hydroxy-4,5-bis (hydroxyl–methyl) pyridine (pyridoxine) is described. The catalytic activity of PB was explored in terms of Fe^III [Fe^III (CN)₆]/Fe^III [Fe^II (CN)₆]¹⁻ system. The best mediated oxidation of pyridoxine (PN) on the PB/Pd–Al-modified electrode was achieved in 0.5 M KNO₃ + 0.2 M potassium acetate of pH 6 at scan rate of 20 mV s⁻¹. The mechanism and kinetics of the catalytic oxidation reaction of PN were monitored by cyclic voltammetry and chronoamperometry. The results were explained using the theory of electrocatalytic reactions at chemically modified electrodes. The charge transfer-rate limiting reaction step is found to be a one-electron abstraction, whereas a two-electron charge transfer reaction is the overall oxidation reaction of PN by forming pyridoxal. The value of α, k, and D are 0.5, 1.2 × 10² M⁻¹ s⁻¹, and 1.4 × 10⁻⁵ cm² s⁻¹, respectively. Further examination of the modified electrodes shows that the modifying layers (PB) on the Pd–Al substrate have reproducible behavior and a high level of stability after posing it in the electrolyte or Pyridoxine solutions for a long time.     

Oxygen reduction in acid media by a Ru<Subscript>x</Subscript>Fe<Subscript>y</Subscript>Se<Subscript>z</Subscript>(CO)<Subscript>n</Subscript> cluster catalyst dispersed on a glassy carbon-supported Nafion film

Electrocatalytic oxygen reduction was studied on a Ru_xFe_ySe_z(CO)_n cluster catalyst with Vulcan carbon powder dispersed into a Nafion film coated on a glassy carbon electrode. The synthesis of the electrocatalyst as a mixture of crystallites and amorphous nanoparticles was carried out by refluxing the transition metal carbonyl compounds in an organic solvent. Electrocatalysis by the cluster compound is discussed, based on the results of rotating disc electrode measurements in a 0.5 M H₂SO₄. A Tafel slope of −80.00±4.72 mV dec⁻¹ and an exchange current density of 1.1±0.17×10⁻⁶ mA cm⁻² was calculated from the mass transfer-corrected curve. It was found that the electrochemical reduction reaction follows the kinetics of a multielectronic (n=4e⁻) charge transfer process producing water, i.e. O₂+4H⁺+4e⁻→2H₂O. Electronic Publication     

Azide-selective sensor based on tripodal iron complex for direct azide determination in aqueous samples

A potentiometric azide-selective sensor based on the use of iron(III) hydrotris(3,5-dimethylpyrazolyl)borate acetylacetonate chloride [Tp^Me2Fe(acac)Cl] as a neutral carrier for an azide-selective electrode is reported. Effect of various plasticizers, viz. o-nitrophenyloctyl ether (o-NPOE), dioctylphthalate (DOP), dibutylphthalate (DBP), and benzylacetate (BA), and an anion excluder, hexadecyltrimethylammonium bromide (HTAB), with [Tp^Me2Fe(acac)Cl] complex in poly(vinyl chloride) (PVC) were studied. The best performance was obtained with a membrane composition of [Tp^Me2Fe(acac)Cl]/HTAB/DOP/PVC in a ratio of 5:2:190:100 (w/w). The sensor exhibits significantly enhanced selectivity toward azide ions over the concentration range 6.3 × 10⁻⁷ to 1.0 × 10⁻² M with a lower detection limit of 3.8 × 10^–7 M and a Nernstian slope of 59.4 ± 1.1 mV decade⁻¹. Influences of the membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. Fast and stable response, good reproducibility, long-term stability and applicability over a wide pH range (3.5–9.0) are demonstrated. The sensor has a response time of 14 s and can be used for at least 45 days without any considerable divergence in the potential response. The proposed electrode shows fairly good discrimination of azide from several inorganic and organic anions. It was successfully applied to the direct determination of azide in orange juice, tea extracts and human urine samples.     

Silver(I)-selective electrode based on [Bz2Oxo4(18)dieneS4] tetrathia macrocyclic carrier

A polystyrene-based membrane of 7,8:16,17-dibenzo-6,9,15,18-tetraoxo-1,5,10,14-tetrathiacyclooctadeca-7,16-diene [Bz₂Oxo₄(18)dieneS₄] was fabricated using sodium tetraphenylborate (NaTPB) and dioctyl phthalate (DOP) as anion excluder and plasticizing agent. The best performance was obtained from the membrane with the composition ionophore [Bz₂Oxo₄(18)dieneS₄]:polystyrene:DOP:NaTPB, 5:100:150:10 (w/w). The response of the electrode was linear over a wide range of concentration, 1.26×10^–6–1.00×10^–1 mol L⁻¹ for silver ion with a Nernstian slope of 58.4±0.1 mV per decade and a detection limit of 1.0×10⁻⁶ mol L⁻¹. The electrode was found to be chemically inert and of adequate stability with a response time of 10 s and could be used for a period of 3 months without change of potential. It worked satisfactorily in mixtures containing up to 35% (v/v) non-aqueous content. The proposed membrane sensor had good selectivity for Ag⁺ over a wide variety of metal ions in the pH range 2.2–8.5. It was successfully used as an indicator electrode in potentiometric titration of silver ion. The electrode was also useful for determination of Ag⁺ in waste from photographic films.     

Fabrication of an iron(III)-selective PVC membrane sensor based on a bis-bidentate Schiff base ionophore

A Fe³⁺ ion-selective membrane sensor was fabricated from polyvinyl chloride (PVC) matrix membrane containing bis-bidentate Schiff base (BBS) as a neutral carrier, sodium tetraphenyl borate (NaTPB) as anionic excluder, and o-nitrophenyloctyl ether (NPOE) as a plasticizing solvent mediator. The effects of the membrane composition, pH, and additive anionic influence on the response properties were investigated. The best performance was obtained with a membrane containing 32% PVC, 62.5% NPOE, 3% BBS, and 2.5% NaTPB. The electrode shows a Nernstian behavior (slope of 19.3 ± 0.6) over a very wide iron ion concentration range (1.0 × 10⁻⁷–1.0 × 10⁻² M) and has a low detection limit (7.4 × 10⁻⁸ M). The potentiometric response of the sensor is independent of pH of the solution in the pH range 1.9–5.1. The proposed sensor has a very low response time (<15 s) and a good selectivity relative to a wide variety of other metal ions including common alkali, alkaline earth, heavy, and transition metal ions. The electrode can be used for at least 60 days without any considerable divergence in potentials. The proposed sensor was successfully applied as an indicator electrode for the potentiometric titration of 1.0 × 10⁻² M Fe³⁺ ions with a 1.0 × 10⁻⁴ M EDTA and the direct determination of Fe³⁺ in mineral water and wastewater samples.     

Thiocyanate-selective electrode based on N-salicylidene-benzylamineato copper(II) complex

Highly selective poly(vinyl chloride) (PVC) membrane electrode based on N-salicylidene-benzylamineato copper(II) complexes [Cu(SBA)₂] as new carriers towards thiocyanate-selective electrode was reported. The influence of membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. The resulting electrode exhibits anti-Hofmeister selectivity sequence: SCN⁻ > ClO₄⁻ > Sal⁻ > I⁻ > Br⁻ > NO₃⁻ > NO₂⁻ > SO₃²⁻ > H₂PO₄⁻ > Cl⁻ > SO₄²⁻, and a near-Nernstian potential linear range for thiocyanate from 1.0 × 10⁻¹ to 9.0 × 10⁻⁷ M with a detection limit of 7.0 10⁻⁷ M and a slope of , over a wide pH range of 3.0–9.0 in phosphate buffer solution at 20°C. The proposed electrode has a fast response time of about 5–10 s and can be used for at least 3 months without any considerable divergence in potential. The electrode was successfully applied to the determination of thiocyanate in waste water and human urine and saliva samples. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 3, pp. 293–299. The text was submitted by the authors in English.     

Thermochemical properties of MnNb<Subscript>2</Subscript>O<Subscript>6</Subscript>

Homogeneous manganocolumbite (MnNb₂O₆) was synthesized from Nb₂O₅ and MnO oxides. Powder sample was orthorhombic with unit cell parameters: α = 0.5766 nm, b = 1.4439 nm, c = 0.5085 nm and V = 0.4234 nm³. Heat capacity over the temperature range of 313–1253 K was measured in an inert atmosphere with combined thermogravimetry and calorimetry using NETZSCH STA 449C Jupiter thermoanalyzer. Melting point was 1767 ± 3 K, enthalpy of melting was 144 ± 4 kJ mol⁻¹. Experimental heat capacity of MnNb₂O₆ is fitted to polynomial C _pm = 221.46 + 3.03 · 10⁻³ T + −39.79 · 10⁵ T ⁻² + 40.59 · 10⁻⁶ T ².     

Composition of the gas phase over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and the enthalpies of atomization of AlO,Al<Subscript>2</Subscript>O,and Al<Subscript>2</Subscript>O<Subscript>2</Subscript>

The A1, O, AlO, A1₂O, Al₂O₂, WO₂, and WO₃, partial pressures in the vapor over Al₂O₃ in a tungsten Knudsen effusion cell between 2300 and 2600 K were derived from A1⁺, O⁺, AlO⁺, A1₂O⁺, Al₂O₂⁺, WO₂⁺, and WO₃⁺, ion intensities. The mass spectrometer was calibrated against the equilibrium constant of the WO₃(g) = WO₂(g) + O(g) reaction. Refined values of the ionization cross sections of AlO and A1₂O₂ were used in the partial pressure calculations. The enthalpies of atomization of aluminum suboxides were determined to be Δ_at H ^o(AlO, g, 0) = 510.7 ± 3.3 kJ mol⁻¹, Δ_at H ^o(Al₂O, g, 0) = 1067.2 ± 6.9 kJ mol⁻¹, and Δ_at H ^o(Al₂O₂, g, 0) = 1556.7 ± 9.9 kJ mol⁻¹.     

Cobalt(II) ion-selective electrode with solid contact

A new all plastic sensor for Co²⁺ ions based on 2-amino-5 (hydroxynaphtyloazo-1′)-1,3,4 thiadiazole (ATIDAN) as ionophore was prepared. The electrode exhibits a low detection limit of 1.5 × 10⁻⁶ mol L⁻¹ and almost theoretical Nernstian slope in the activity range 4.0 × 10⁻⁶–1 × 10⁻¹ mol L⁻¹ of cobalt ions. The response time of the sensor is less than 10 s and it can be used over a period of 6 months without any measurable divergence in potential. The proposed sensor shows a fairly good selectivity for Co(II) over other metal ions. The electrode was successfully applied for determination of Co²⁺ in real samples and as an indicator electrode in potentiometric titration of Co²⁺ ions with EDTA.      

PuPO<Subscript>4</Subscript>(cr,hyd.) Solubility Product and Pu<Superscript>3+</Superscript> Complexes with Phosphate and Ethylenediaminetetraacetic Acid

To determine the solubility product of PuPO₄(cr, hyd.) and the complexation constants of Pu(III) with phosphate and EDTA, the solubility of PuPO₄(cr, hyd.) was investigated as a function of: (1) time and pH (varied from 1.0 to 12.0), and at a fixed 0.00032 mol⋅L⁻¹ phosphate concentration; (2) NaH₂PO₄ concentrations varying from 0.0001 mol⋅L⁻¹ to 1.0 mol⋅L⁻¹ and at a fixed pH of 2.5; (3) time and pH (varied from 1.3 to 13.0) at fixed concentrations of 0.00032 mol⋅L⁻¹ phosphate and 0.0004 mol⋅L⁻¹ or 0.002 mol⋅L⁻¹ Na₂H₂EDTA; and (4) Na₂H₂EDTA concentrations varying from 0.00005 mol⋅L⁻¹ to 0.0256 mol⋅L⁻¹ at a fixed 0.00032 mol⋅L⁻¹ phosphate concentration and at pH values of approximately 3.5, 10.6, and 12.6. A combination of solvent extraction and spectrophotometric techniques confirmed that the use of hydroquinone and Na₂S₂O₄ helped maintain the Pu as Pu(III). The solubility data were interpreted using the Pitzer and SIT models, and both provided similar values for the solubility product of PuPO₄(cr, hyd.) and for the formation constant of PuEDTA⁻. The log ₁₀ of the solubility product of PuPO₄(cr, hyd.) [PuPO₄(cr, hyd.) \rightleftarrows\rightleftarrows Pu³⁺+PO₄^3-\mathrm{Pu}^{3+}+\mathrm{PO}_{4}^{3-}] was determined to be −(24.42±0.38). Pitzer modeling showed that phosphate interactions with Pu³⁺ were extremely weak and did not require any phosphate complexes [e.g., PuPO₄(aq), PuH₂PO₄²⁺\mathrm{PuH}_{2}\mathrm{PO}_{4}^{2+}, Pu(H₂PO₄)₂⁺\mathrm{Pu(H}_{2}\mathrm{PO}_{4})_{2}^{+}, Pu(H₂PO₄)₃(aq), and Pu(H₂PO₄)₄^-\mathrm{Pu(H}_{2}\mathrm{PO}_{4})_{4}^{-}] as proposed in existing literature, to explain the experimental solubility data. SIT modeling, however, required the inclusion of PuH₂PO₄²⁺\mathrm{PuH}_{2}\mathrm{PO}_{4}^{2+} to explain the data in high NaH₂PO₄ concentrations; this illustrates the differences one can expect when using these two different chemical models to interpret the data. Of the Pu(III)-EDTA species, only PuEDTA⁻ was needed to interpret the experimental data over a large range of pH values (1.3–12.9) and EDTA concentrations (0.00005–0.256 mol⋅L⁻¹). Calculations based on density functional theory support the existence of PuEDTA⁻ (with prospective stoichiometry as Pu(OH₂)₃EDTA⁻) as the chemically and structurally stable species. The log ₁₀ value of the complexation constant for the formation of PuEDTA⁻ [ Pu³⁺+EDTA^4-\rightleftarrows PuEDTA^-\mathrm{Pu}^{3+}+\mathrm{EDTA}^{4-}\rightleftarrows \mathrm{PuEDTA}^{-}] determined in this study is −20.15±0.59. The data also showed that PuHEDTA(aq), Pu(EDTA)₄^5-\mathrm{Pu(EDTA)}_{4}^{5-}, Pu(EDTA)(HEDTA)⁴⁻, Pu(EDTA)(H₂EDTA)³⁻, and Pu(EDTA)(H₃EDTA)²⁻, although reported in the literature, have no region of dominance in the experimental range of variables investigated in this study.     

PbO<Subscript>2</Subscript>-SnO<Subscript>2</Subscript> composite anode with interconnected structure for the electrochemical incineration of phenol

A PbO₂-SnO₂ composite anode with interconnected structure is prepared for organics electro-incineration through a two-step method, thermal-decomposition process and subsequent low-current density electrodeposition process. The element mapping, together with the impedance spectra of the composite electrode, confirms that an interconnected architecture of SnO₂ and PbO₂ grains, instead of a lamellar structure, was obtained on the Ti substrate. A lower electrodeposition current density (≤10 mA cm⁻²) is very crucial for the formation of a porous surface and an interconnected architecture of two oxides inside. The asprepared electrode exhibits an enhanced electrocatalytic activity on the mineralization of phenol and a long service life due to the interconnected architecture, which helps to utilize the merits of these two metal oxides simultaneously. This two-step method also provides us a novel and facile way to fabricate a series of composite material such as oxide-oxide, oxide-metal composite electrodes.     

Electrochemical generation of ozone at PbO2-loaded platinum screens

Ozone (O₃) has been electrochemically generated on PbO₂-loaded Pt screens (PbO₂/Pts) at 25 °C from H₂SO₄ solutions. The PbO₂/Pts electrodes were electrochemically and morphologically characterized by cyclic voltammetry and scanning electron microscopy (SEM), respectively. Different loadings of PbO₂ and different acid concentrations (C _acid) were used in this study. Higher efficiency (8%) for O₃ electrogeneration was obtained at an applied potential of 1.8 V, higher C _acid, and loading density of PbO₂ ≥ 9.3 μmol cm⁻² (of Pt screen) at room temperature. The stability of the prepared electrode was examined under the present experimental conditions. SEM images and current transients showed reasonable electrochemical and mechanical stability of the PbO₂/Pts. The data were discussed in the light of results obtained on planar Pt electrode at similar conditions.     

The amperometric determination of indole-3-acetic acid based on CeCl<Subscript>3</Subscript>-DHP film modified gold electrode

An amperometric sensor for the determination of indole-3-acetic acid (IAA) based on the CeCl₃-DHP film modified gold electrode was developed. CeCl₃ was dissolved into water in the presence of dihexadecyl hydrogen phosphate (DHP). The IAA sensor was prepared via evaporating solvent of the CeCl₃-DHP dispersion on the gold electrode surface. The amperometric response of IAA on the CeCl₃-DHP film modified gold electrode was investigated. The experimental results indicate that the passivation of the electrode due to the adsorption of the oxidation product of IAA decreases significantly at the CeCl₃-DHP film modified gold electrode, in contrast to that at the bare and the DHP modified gold electrode. The experimental parameters were optimized and an electrochemical method for the determination of IAA was established. The oxidation peak current is linearly with the concentration of IAA from 1 × 10⁻⁷ to 2 × 10⁻⁵ mol l⁻¹ and the detection limit is 3 × 10⁻⁸ mol l⁻¹. The relative standard deviation of eight measurements is 3.2% for 5 × 10⁻⁷ mol l⁻¹ IAA. The IAA in plant leaves were extracted and determined by the IAA sensor.     

Determination of nanomolar lead (II) using H<Subscript>2</Subscript>O<Subscript>2</Subscript>-oxidized activated carbon modified electrode

The virgin activated carbon (AC) was oxidized by 30% H₂O₂ under the ultrasonic condition for 6 h (denoted as AC-6). The electrochemical response of Pb²⁺ at the AC-6 modified paste electrode was investigated, suggesting that AC-6 shows much higher accumulation efficiency to trace levels of Pb²⁺. Based on this, a sensitive and convenient electrochemical method was developed for the determination of Pb²⁺ utilizing the excellent properties of AC-6. In pH 3.6 HAc-NaAc buffer, Pb²⁺ was easily accumulate at the surface of AC-6 modified paste electrode, then reduced to Pb at −1.20 V. During the following anodic sweep, the reduced Pb was oxidized and resulted in an oxidation stripping peak at −0.58 V. The stripping peak current is proportional to the concentration of Pb²⁺ over the range from the 8.0 × 10⁻⁹ to 2.0 × 10⁻⁶ mol l⁻¹, and the limit of detection is as low as 2.0 × 10⁻⁹ mol l⁻¹. Finally, this newly-developed method was successfully employed to determine Pb²⁺ in water samples.     

Determination of ultra-trace amounts of inorganic selenium species in natural water by ion chromatography-inductively coupled plasma-mass spectrometry coupled with nano-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> solid phase extraction

This work presents a nano-Al₂O₃ solid phase extraction technique for the determination of ultra-trace amounts of inorganic selenium species in aqueous systems using ion chromatography inductively coupled plasma-mass spectrometry (IC-ICP-MS). In this experiment, the inorganic selenium species were successfully extracted on a nano-Al₂O₃ solid phase column and then quantitative eluted with a 100 mmol L⁻¹ NaOH solution. Extraction conditions such as solvent identity, solvent concentration, solvent volume, solvent pH and salt addition were optimized. Under the optimum extraction conditions (elute solvent: 100 mmol L⁻¹ NaOH, solvent volume: 4 mL, pH: 7.0), low detection limits (Se (IV): 6 ng L⁻¹, Se (VI): 11 ng L⁻¹; RSD<5.0%) and good linear range (0.5–100 ng mL⁻¹, R² > 0.999) were obtained for all of the analytes. Good spiked recoveries over the range of 80–98% were obtained by applying the proposed method on real environmental water samples. These results indicated that this method is very sensitive and reliable when monitoring trace levels of inorganic selenium species in aqueous samples.      

Studies on the electrochemical and thermodynamic behaviour of Hg-HgS electrode in the presence of sulphide ions

Mercury-mercury (II) sulphide electrode has been prepared and its electrochemical and thermodynamic behaviour has been studied in different media. The electrode is found to show Nernstian response to pS (− log [S²⁻]) over the range 5.19–10.38. In the pH range 7.96–11.98, at constant [S²⁻]_v, its response is also Nernstian. The values of thermodynamic functions, viz., ΔG⁰. ΔH⁰, and ΔS⁰ for the electrode reaction: Hg₍₃)+S²⁻ _aμ ⇌HgS_(s)+2e, have been determined. Further, the standard free energy of formation (ΔG _f ⁰ ) and solubility product constant (K _vp ) of HgS in aqueous medium at 25±0.1°C have also been determined.     

Chromium(III) complexes with lutidinic acid: kinetic studies in HClO<Subscript>4</Subscript> and NaOH solutions

Chromium(III)-lutidinato complexes of general formula [Cr(lutH) _n (H₂O)_6−2n ]³⁻ⁿ (where lutH⁻ is N,O-bonded lutidinic acid anion) were obtained and characterized in solution. Acid-catalysed aquation of [Cr(lutH)₃]⁰ leads to only one ligand dissociation, whereas base hydrolysis produces chromates(III) as a result of subsequent ligand liberation steps. The kinetics of the first ligand dissociation were studied spectrophotometrically, within the 0.1–1.0 M HClO₄ and 0.4–1.0 M NaOH range. In acidic media, two reaction stages, the chelate-ring opening and the ligand dissociation, were characterized. The dependencies of pseudo-first-order rate constants on [H⁺] are as follows: k _obs1 = k ₁ + k ₋₁/K ₁[H⁺] and k _obs2 = k ₂ K ₂[H⁺]/(1 + K ₂[H⁺]), where k ₁ and k ₂ are the rate constants for the chelate-ring opening and the ligand dissociation, respectively, k ₋₁ is the rate constant for the chelate-ring closure, and K ₁ and K ₂ are the protonation constants of the pyridine nitrogen atom and coordinated 2-carboxylate group in the one-end bonded intermediate, respectively. In alkaline media, the rate constant for the first ligand dissociation depends on [OH⁻]: k _obs1 = k _OH(1) + k _O[OH⁻], where k _OH(1) and k _O are rate constants of the first ligand liberation from the hydroxo- and oxo-forms of the intermediate, respectively, and K ₂ is an equilibrium constant between these two protolytic forms. Kinetic parameters were determined and a mechanism for the first ligand dissociation is proposed. The kinetics of the ligand liberation from [Cr(lut)(OH)₄]³⁻ were also studied and the values of the pseudo-first-order rate constants are [OH⁻] independent.     

Cobalt(II)-selective membrane sensor based on a [Me2(13)dieneN4] macrocyclic cobalt complex

A new poly(vinyl chloride)-based membrane was fabricated with the cobalt(II) complex of 2,4-dimethyl-1,5,8,11-tetraazacyclotrideca-1,4-diene [Me₂(13)dieneN₄] as an ion carrier. The membrane composition was Co²⁺ complex/PVC/NaTPB/DBP 15:50:15:20 (w/w). The sensor exhibited a Nernstian response for Co²⁺ ions over a wide concentration range (7.94×10⁻⁶–1.0×10⁻¹ M) at pH 2.5–7.0, a response time of 10 s, and it could be used for 3 months without any significant divergence in potential. The proposed membrane sensor exhibited good selectivity for Co²⁺ over a wide variety of other metal ions and in mixtures containing up to 25% (v/v) non-aqueous content. The sensor was successfully used as an indicator electrode in the potentiometric titration of Co²⁺ with EDTA and the direct determination of Co²⁺ in real samples.     

Determination of diclofenac in pharmaceuticals and urine samples using a membrane sensor based on the ion associate of diclofenac with Rhodamine B

The potentiometric response characteristics of a diclofenac selective electrode, based on ion association in different plasticizers, were compared. The sensitivity, working range, detection limit and selectivity of membrane sensors demonstrated significant dependence on the type of plasticizers. The potentiometric unit presented a linear response toward diclofenac concentrations between 1 × 10⁻⁵ − 5 × 10⁻² mol L⁻¹, with slopes of approximately 60 mV dec⁻¹, and exhibited a response time of 3 s. The potentiometric analysis of sodium diclofenac in pharmaceutical formulations was perfomed by the membrane electrode proposed and compared with the results of potentiometric titration given by the Pharmacopoeia of Ukraine.