Comparison of GC–MS and MEKC methods for caffeine determination in preworkout supplements

In this study, GC–MS‐ and MEKC‐based methods for determination of caffeine (CAF) in preworkout supplements were developed and validated. The proposed protocols utilized minimal sample preparation (simple dilution and syringe filtration). The developed methods achieved satisfactory validation parameters, i.e. good linearity (R² > 0.9988 and R² > 0.9985 for GC–MS‐ and MEKC‐based method, respectively), satisfactory intra‐ and interaccuracy (within 92.6–100.7% for method utilizing GC–MS and 92.1–110.3% for protocol based on MEKC) and precision (CV < 15.9% and CV < 6.3% for GC–MS‐ and MEKC‐based method, respectively) and recovery (within 100.1–100.8% for method utilizing GC–MS and 101.5–106.2% for protocol based on MEKC). The LOD was 0.03 and 3 μg/mL for method utilizing GC–MS and MEKC, respectively. The CAF concentrations determined by GC–MS‐ and MEKC‐based methods were found to be in the range of 8.53–11.23 and 8.20–11.61 μg/mL, respectively. Taking into consideration information on the labels, the investigated supplements were found to contain from 110.0 to 167.3% of the declared CAF content, which confirmed the literature reports on incompatibility of the declared product compositions with real ones. Nevertheless, the consumption of examined supplements as recommended by producers did not lead to exceeding the CAF safe limit of 400 mg per day. Additionally, the MEKC‐based method allowed for detection and identification of vitamin B3 and B6 in all of the investigated supplement samples, which demonstrated that MEKC‐based protocols may be an appropriate assays for simultaneous determination of CAF and vitamins.     

Analysis of pesticide residues using the Quick Easy Cheap Effective Rugged and Safe (QuEChERS) pesticide multiresidue method in combination with gas and liquid chromatography and tandem mass spectrometric detection

The Quick Easy Cheap Effective Rugged and Safe multiresidue method (QuEChERS) has been validated for the extraction of 80 pesticides belonging to various chemical classes from various types of representative commodities with low lipid contents. A mixture of 38 pesticides amenable to gas chromatography (GC) were quantitatively recovered from spiked lemon, raisins, wheat flour and cucumber, and determined using gas chromatography-tandem mass spectrometry (GC-MS/MS). An additional mixture of 42 pesticides were recovered from oranges, red wine, red grapes, raisins and wheat flour, using liquid chromatography-tandem mass spectrometry (LC-MS/MS) for determination. The pesticides chosen for this study included many of the most frequently detected ones and/or those that are most often found to violate the maximum residue limit (MRL) in food samples, some compounds that have only recently been introduced, as well as a few other miscellaneous compounds. The method employed involved initial extraction in a water/acetonitrile system, an extraction/partitioning step after the addition of salt, and a cleanup step utilizing dispersive solid-phase extraction (D-SPE); this combination ensured that it was a rapid, simple and cost-effective procedure. The spiking levels for the recovery experiments were 0.005, 0.01, 0.02 and 0.2 mg kg(-1) for GC-MS/MS analyses, and 0.01 and 0.1 mg kg(-1) for LC-MS/MS analyses. Adequate pesticide quantification and identity confirmation were attained, even at the lowest concentration levels, considering the high signal-to-noise ratios, the very good accuracies and precisions, as well as the good matches between the observed ion ratios. Mean recoveries mostly ranged between 70 and 110% (98% on average), and relative standard deviations (RSD) were generally below 10% (4.3% on average). The use of analyte protectants during GC analysis was demonstrated to provide a good alternative to the use of matrix-matched standards to minimize matrix-effect-related errors. Based on these results, the methodology has been proven to be highly efficient and robust and thus suitable for monitoring the MRL compliance of a wide range of commodity/pesticide combinations.     

Benzimidazole carbamate residues in milk: Detection by Surface Plasmon Resonance-biosensor, using a modified QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) method for extraction

A surface plasmon resonance (SPR) biosensor screening assay was developed and validated to detect 11 benzimidazole carbamate (BZT) veterinary drug residues in milk. The polyclonal antibody used was raised in sheep against a methyl 5(6)-[(carboxypentyl)-thio]-2-benzimidazole carbamate protein conjugate. A sample preparation procedure was developed using a modified QuEChERS method. BZT residues were extracted from milk using liquid extraction/partition with a dispersive solid phase extraction clean-up step. The assay was validated in accordance with the performance criteria described in 2002/657/EC. The limit of detection of the assay was calculated from the analysis of 20 known negative milk samples to be 2.7 μg kg⁻¹. The detection capability (CCβ) of the assay was determined to be 5 μg kg⁻¹ for 11 benzimidazole residues and the mean recovery of analytes was in the range 81-116%. A comparison was made between the SPR-biosensor and UPLC-MS/MS analyses of milk samples (n = 26) taken from cows treated different benzimidazole products, demonstrating the SPR-biosensor assay to be fit for purpose.     

Simple method for the determination of personal care product ingredients in lettuce by ultrasound‐assisted extraction combined with solid‐phase microextraction followed by GC–MS

A simple method for the simultaneous determination of personal care product ingredients: galaxolide, tonalide, oxybenzone, 4‐methylbenzyliden camphor, padimate‐o, 2‐ethylhexyl methoxycinnamate, octocrylene, triclosan, and methyl triclosan in lettuce by ultrasound‐assisted extraction combined with solid‐phase microextraction followed by gas chromatography with mass spectrometry was developed. Lettuce was directly extracted by ultrasound‐assisted extraction with methanol, this extract was combined with water, extracted by solid‐phase microextraction in immersion mode, and analyzed by gas chromatography with mass spectrometry. Good linear relationships (25–250 ng/g, R² > 0.9702) and low detection limits (1.0–25 ng/g) were obtained for analytes along with acceptable precision for almost all analytes (RSDs < 20%). The validated method was applied for the determination of personal care product ingredients in commercial lettuce and lettuces grown in soil and irrigated with the analytes, identifying the target analytes in leaves and roots of the latter. This procedure is a miniaturized and environmentally friendly proposal which can be a useful tool for quality analysis in lettuce.     

Simultaneous determination of difenoconazole,trifloxystrobin and its metabolite trifloxystrobin acid residues in watermelon under field conditions by GC–MS/MS

An optimized quick, easy, cheap, effective, rugged and safe method for the simultaneous determination of difenoconazole, trifloxystrobin and its metabolite trifloxystrobin acid residues in watermelon and soil was developed and validated by gas chromatography with tandem mass spectrometry. The samples were extracted with acetonitrile (1% formic acid) and cleaned up by dispersive solid‐phase extraction with octadecylsilane sorbent. The limit of quantification of the method was 0.01 mg/kg, and the limit of detection was 0.003 mg/kg for all three analytes. The recoveries of the fungicides in watermelon, pulp and soil were 72.32–99.20% for difenoconazole, 74.68–87.72% for trifloxystrobin and 78.59–92.66% for trifloxystrobin acid with relative standard deviations of 1.34–14.04%. The dissipation dynamics of difenoconazole and trifloxystrobin in watermelon and soil followed the first‐order kinetics with half‐lives of 3.2–8.8 days in both locations. The final residue levels of difenoconazole and trifloxystrobin were below 0.1 mg/kg (maximum residue level [MRL] set by China) and 0.2 mg/kg (MRL set by European Union), respectively, in pulp samples collected 14 days after the last application. These results could help Chinese authorities to establish MRL of trifloxystrobin in watermelon and provide guidance for the safe and proper application of both fungicides on watermelon.     

Comparison of Different d-SPE Sorbent Performances Based on Quick,Easy, Cheap,Effective, Rugged,and Safe (QuEChERS) Methodology for Multiresidue Pesticide Analyses in Rapeseeds

Pesticide extraction in rapeseed samples remains a great analytical challenge due to the complexity of the matrix, which contains proteins, fatty acids, high amounts of triglycerides and cellulosic fibers. An HPLC-MS/MS method was developed for the quantification of 179 pesticides in rapeseeds. The performances of the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method were evaluated using different dispersive solid-phase extraction (d-SPE) sorbents containing common octadecylsilane silica/primary–secondary amine adsorbent (PSA/C18) and new commercialized d-SPE materials dedicated to fatty matrices (Z-Sep, Z-Sep⁺, and EMR-Lipid). The analytical performances of these different sorbents were compared according to the SANTE/12682/2019 document. The best results were obtained using EMR-Lipid in terms of pesticide average recoveries (103 and 70 of the 179 targeted pesticides exhibited recoveries within 70–120% and 30–70%, respectively, with low RSD values). Moreover, the limits of quantification (LOQ) range from 1.72 µg/kg to 6.39 µg/kg for 173 of the pesticides. Only the recovery for tralkoxydim at 10 μg/kg level was not satisfactory (29%). The matrix effect was evaluated and proved to be limited between −50% and 50% for 169 pesticides with this EMR-Lipid and freezing. GC-Orbitrap analyses confirmed the best efficiency of the EMR-Lipid sorbent for the purification of rapeseeds.     

GC–MS with photoionization of cold molecules in supersonic molecular beams—Approaching the softest ionization method

A new type of photoionization ion source was developed for the ionization of cold molecules in supersonic molecular beams (named Cold PI). The system was based on a GC–MS with supersonic molecular beams and its fly‐through EI of cold molecules ion source (Cold EI) plus quadrupole mass analyzer. A continuously operated deuterium VUV photoionization lamp was added and placed above and between the supersonic nozzle and skimmer whereas the Cold EI ion source served only as a portion of the ion transfer ion optics. The supersonic nozzle and skimmer were voltage biased and the VUV light crossed the supersonic expansion about 10 mm from the nozzle. We obtained over three orders of magnitude enhancement in the relative abundance of the molecular ion of squalane in Cold PI versus in photoionization of this compound as a thermal compound. Accordingly, we also proved that standard photoionization is not as soft ionization method as previously perceived for large compounds. We found that Cold PI is as soft as and possibly softer than field ionization; thus, it could be the softest known ionization method. The ionization yield was about 200–300 times weaker than with Cold EI yet our limit of detection was about 200 femtogram in SIM mode for cholesterol and pyrene which is reasonable. Practically, all hydrocarbons gave only molecular ions with rather uniform response whereas alcohols gave some molecular ions plus major fragment ions particularly with a loss of water (similarly to field ionization). We tested Cold PI in the GC–MS analysis of diesel fuels and analyzed the time averaged data for group type information. We also found that we can analyze the diesel fuels by fast under 20‐s flow injection analysis in which the generated averaged mass spectrum of molecular ions only could serve for the characterization of fuels.     

Pyrolysis of residual palm oil in spent bleaching clay by modified tubular furnace and analysis of the products by GC–MS

In this study, spent bleaching clay containing 26.6 wt.% of residual palm oil was pyrolyzed using a tubular furnace. Carboxylic acids ranging from C₉-C₁₈ and alkanes ranging from C₁₆-C₄₄ were the major classes of compounds found in the pyrolytic products analyzed using GC-MS. Significant amounts of monoaromatic compounds, alkenes, alcohols, ketones, aldehydes, esters, nitrogenated compounds, and polycyclic aromatic hydrocarbons (PAHs) were found in the bio-oil produced in this study. The bio-oil resulting from the pyrolysis process gave n-hexadecanoic acid as the major compound. Decomposition temperature of the adsorbed oil determined using TGA was found to be in the range of 573-683 K. Topographical and elemental analyses of the clay was done using SEM-EDX. The functional groups were determined using FTIR.     

High resolution capillary GC–MS analysis of low molecular weight organic compounds in municipal wastewater

High resolution capillary gas chromatography–mass spectrometry has been used in combination with various sample preparation methods to analyze a wide range of low molecular weight organic contaminants in municipal wastewaters. Volatile organic compounds were extracted using a purge and trap concentrator connected directly to a wide bore DB-624 capillary column. Because of the high organic load in wastewater samples, this method was preferred to the more sensitive closed loop stripping technique which suffered from competition effects and insufficient adsorbent capacity. Volatile and semi-volatile base/neutral compounds and acids were extracted with dichloromethane at pH 11 and pH 2, respectively, or were recovered using a simultaneous distillation-extraction procedure. Acidic compounds were subsequently derivatized using diazomethane methylation. Both fractions were separated with a 30m DB-5ms capillary column. Specific ionic substances (LAS, NTA, EDTA) were isolated by solid-phase extraction then derivatized with diazomethane (LAS) or acetyl chloride in n-butanol (NTA, EDTA) before GC–MS analysis. This array of techniques enabled the identification of more than 150 organic contaminants in the influent of a municipal wastewater treatment plant in northern suburban Paris. The individual concentrations of these contaminants ranged from < 0.1 μg/l to 5.7 mg/l.     

Determination of phthalate esters in bottled water using dispersive liquid–liquid microextraction coupled with GC–MS

Dispersive liquid–liquid microextraction method was developed for the determination of the amount of phthalate esters in bottled drinking water samples and dispersive liquid–liquid microextraction samples were analyzed by GC–MS. Various experimental conditions influencing the extraction were optimized. Under the optimized conditions, very good linearity was observed for all analytes in a range between 0.05 and 150 μg/L with coefficient of determination (R²) between 0.995 and 0.999. The LODs based on S/N = 3 were 0.005–0.22 μg/L. The reproducibility of dispersive liquid–liquid microextraction was evaluated. The RSDs were 1.3–5.2% (n = 3). The concentrations of phthalates were determined in bottled samples available in half shell. To understand the leaching profile of these phthalates from bottled water, bottles were exposed to direct sunlight during summer (temperature from 34–57°C) and sampled at different intervals. Result showed that the proposed dispersive liquid–liquid microextraction is suitable for rapid determination of phthalates in bottled water and di‐n‐butyl, butyl benzyl, and bis‐2‐ethylhexyl phthalate compounds leaching from bottles up to 36 h. Thereafter, degradation of phthalates was observed.     

Nontargeted GC–MS approach for volatile profile of toasting in cherry,chestnut, false acacia,and ash wood

By using a nontargeted GC–MS approach, 153 individual volatile compounds were found in extracts from untoasted, light toasted and medium‐toasted cherry, chestnut, false acacia, as well as European and American ash wood, used in cooperage for aging wines, spirits and other beverages. In all wood types, the toasting provoked a progressive increase in carbohydrate derivatives, lactones and lignin constituents, along with a variety of other components, thus increasing the quantitative differences among species with the toasting intensity. The qualitative differences in the volatile profiles allow for identifying woods from cherry (being p‐anisylalcohol, p‐anisylaldehyde, p‐anisylacetone, methyl benzoate and benzyl salicylate detected only in this wood), chestnut (cis and trans whisky lactone) and false acacia (resorcinol, 3,4‐dimethoxyphenol, 2,4‐dihydroxy benzaldehyde, 2,4‐dihydroxyacetophenone, 2,4‐dihydroxypropiophenone and 2,4‐dihydroxy‐3‐methoxyacetophenone), but not those from ash, because of the fact that all compounds present in this wood are detected in at least one other. However, the quantitative differences can be clearly used to identify toasted ash wood, with tyrosol being most prominent, but 2‐furanmethanol, 3‐ and 4‐ethylcyclotene, α‐methylcrotonolactone, solerone, catechol, 3‐methylcatechol and 3‐hydroxybenzaldehyde as well. Regarding oak wood, its qualitative volatile profile could be enough to distinguish it from cherry and acacia woods, and the quantitative differences from chestnut (vanillyl ethyl ether, isoacetovanillone, butirovanillone, 1‐(5‐methyl‐2‐furyl)‐2‐propanone and 4‐hydroxy‐5,6‐dihydro‐(2H)‐pyran‐2‐one) and ash toasted woods. Copyright © 2014 John Wiley & Sons, Ltd.     

The use of silica‐coated magnetic graphene microspheres as the adsorbent for the extraction of pyrethroid pesticides from orange and lettuce samples followed by GC–MS analysis

Graphene‐grafted ferroferric oxide microspheres were used as the adsorbent to extract some pyrethroid pesticides (bifenthrin, λ‐cyhalothrin, cyfluthrin, cypermethrin, fenvalerate, and deltamethrin) from orange and lettuce samples prior to their determination by GC–MS. The main variables that could affect the extraction, including the amount of the adsorbent, pH of the sample solution, extraction time, concentration of salt, and desorption conditions, were investigated and optimized. Under the optimized conditions, a linear response was obtained in the concentration range of 0.3–100.0 ng/g for the analytes with the coefficients of determination ranging from 0.9877 to 0.9925. The LODs for the pyrethroids ranged from 0.01 to 0.02 ng/g. The method provided a good repeatability with RSDs < 10.6%. The recoveries for the six pyrethroid pesticides were in the range from 90.0 to 103.7%. The method was applied to the determination of the pesticides in orange and lettuce samples with a satisfactory result.     

A highly sensitive GC–MS method for simultaneous determination of anacardic acids in cashew (Anacardium occidentale) nut shell oil in the presence of other phenolic lipid derivatives

The commercial value of cashew nut shell liquid (CNSL) has become a cornerstone of the agrowaste industry. It is the by‐product of the cashew industry and has an 1/8 inch thickness of soft honeycomb structure. CNSL contains phenolic lipids with aliphatic chains such as anacardic acid, cardanol, cardol and methyl cardol, and their derivatives. The developed GC–MS method is rapid, accurate and selective using a selected derivatizing reagent, namely N‐methyl‐N‐(trimethylsilyl)‐trifluoroacetamide that was previously diluted 1:1% with anhydrous pyridine. The proposed GC–MS method was applied for the analysis of different CNSL samples. The results showed that all classes of CNSL compounds were detected. The four alkyl phenols were detected with their different alkyl sidechains without any interference. This method is also specified for the detection of fatty acids of saturated and unsaturated chains. Silylation did not cause any alteration in the chemical structure of CNSL compounds regardless of esterification action. Silylation is considered a safe derivatizing agent compatible with GC chromatography and specific for all volatile and nonvolatile polar and nonpolar CNSL compounds that could be detected in CNSL samples.     

Graphene as an efficient sorbent for the SPE of organochlorine pesticides in water samples coupled with GC–MS

The determination of organochlorine pesticides in water samples, which are harmful to humans, is very important for environmental risk assessment. Based on the excellent adsorption properties of graphene, an SPE coupled with GC–MS method for the monitoring of organochlorines (four hexachlorcyclohexanes and four dichlorodiphenyltrichloroethanes) was developed. Owing to the hydrophobic interaction and π–π stacking interaction between the analytes and graphene, the analytes quantitatively adsorbed onto the graphene‐based SPE cartridge were eluted by ethyl acetate for analysis. Several parameters influencing the analytical performance, such as the kind of elution, sample volume, reusability of the cartridge, have been investigated in detail. Under the optimal conditions, detection of limits of 1.95–9.38 ng/L, recoveries of 83.9–107.3% at two spiked concentration levels (0.1 and 10 ng/mL) and RSDs in the range of 2.9–7.4% for real water samples were obtained for all the analytes. This work reveals the great potential of graphene in sample preparation procedures.     

Determination of tebuconazole, trifloxystrobin and its metabolite in fruit and vegetables by a Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) method using gas chromatography with a nitrogen-phosphorus detector and ion trap mass spectrometry

A new analytical method using QuEChERS procedure by gas chromatography with a nitrogen-phosphorus detector (GC-NPD) and ion trap mass spectrometry (GC-IT-MS) for the quantitative determination of tebuconazole, trifloxystrobin and its metabolite trifloxystrobin acid has been developed and validated. The analytes were extracted from five fruit and vegetable matrices using acetonitrile and subsequently cleaned up using primary secondary amine (PSA) or octadecylsilane (C18) as sorbent prior to GC analysis. The present methods provided sufficient sensitivity as reflected by the values of limit of detection (LOD) and limit of quantification (LOQ) of 0.4-7 and 1.2-20 μg/kg for GC-IT-MS/MS and GC-NPD. The recoveries were, on average, 68-117 and 68-121%, respectively, for three compounds by GC-NPD and GC-IT-MS/MS with intra-day precision achieved with an RSD of 2.7-19.1%. The inter-day precision was better than 15.1% as determined by GC-NPD. The QuEChERS procedure, by using two sorbents (PSA and C18) and the matrix-matched standards, gave satisfactory recoveries and RSD values in different matrices. IT-MS acquisition provided higher specificity and selectivity for pesticides and better limit of detection and quantification. However, the repeatability and precision of NPD method were better compared with IT-MS.     

Rapid determination of parabens in personal care products by stable isotope GC‐MS/MS with dynamic selected reaction monitoring

In this study, a rapid and sensitive analytical method for the determination of methyl‐, ethyl‐, propyl‐, and butyl esters of para‐hydroxy benzoic acid (parabens) in personal care products was developed and fully validated. Test portions were extracted with methanol followed by vortexing, sonication, centrifugation, and filtration without derivatization. The four parabens were quantified by GC‐MS/MS in the electron ionization mode. Four corresponding isotopically labeled parabens were selected as internal standards, which were added at the beginning of the sample preparation and used to correct for recovery and matrix effects. Sensitivity, extraction efficiency, and recovery of the respective analytes were evaluated. The coefficients of determination (r²) were all greater than 0.995 for the four parabens investigated. The recoveries ranged from 97 to 107% at three spiked levels and a one‐time (single) extraction efficiency greater than 97% was obtained. This method has been applied to screen 26 personal care products. This is the first time that a unique GC‐MS/MS method with dynamic selected reaction monitoring and confirmation of analytes has been used to determine these parabens in cosmetic personal care products.     

QuEChERS-气相色谱法快速检测五十种中药材中九种有机氯农药残留的方法研究

建立了简便、快速测定五十种中药材中九种农药的多残留检测方法.以体积比95:4:1的乙腈-水-1%乙酸混合溶液作为提取剂,QuEChERS(Quick,Easy,Cheap,Effective,Rugged,Safe)方法进行净化,采用气相色谱法进行检测.结果表明:九种农药在1.0～100ng/mL范围内线性良好,3个添...     

Simultaneous derivatization and air‐assisted liquid–liquid microextraction of some parabens in personal care products and their determination by GC with flame ionization detection

A simultaneous derivatization/air‐assisted liquid–liquid microextraction technique has been developed for the sample pretreatment of some parabens in aqueous samples. The analytes were derivatized and extracted simultaneously by a fast reaction/extraction with butylchloroformate (derivatization agent/extraction solvent) from the aqueous samples and then analyzed by GC with flame ionization detection. The effect of catalyst type and volume, derivatization agent/extraction solvent volume, ionic strength of aqueous solution, pH, numbers of extraction, aqueous sample volume, etc. on the method efficiency was investigated. Calibration graphs were linear in the range of 2–5000 μg/L with squared correlation coefficients >0.990. Enhancement factors and enrichment factors ranged from 1535 to 1941 and 268 to 343, respectively. Detection limits were obtained in the range of 0.41–0.62 μg/L. The RSDs for the extraction and determination of 250 μg/L of each paraben were <4.9% (n = 6). In this method, the derivatization agent and extraction solvent were the same and there is no need for a dispersive solvent, which is common in a traditional dispersive liquid–liquid microextraction technique. Furthermore, the sample preparation time is very short.     

Determination of endosulfan isomers and their metabolites in tap water and commercial samples using microextraction by packed sorbent and GC–MS

A simple, rapid, accurate and sensitive method using microextraction by packed sorbent (MEPS) followed by GC–MS has been pursued for the determination of organochlorine insecticide endosulfan isomers (α and β) and their metabolites (ether, lactone and sulfate). MEPS is a miniaturised version of SPE employing C₁₈ packing material. It is very efficient technique as it employs as low as 10 μL of sample volume. The distinct feature of MEPS is the magnitude of the elution volume that could be directly injected to GC system. Various parameters such as extraction cycles, washing solvent, elution solvent, elution volume and pH, which influenced the MEPS performance, were tested and optimised. The calibration curves were obtained in the concentration range 1–500 ng/mL. The results showed a close correlation coefficient (R² > 0.991) for all analytes in the calibration range studied. The LOD and LOQ obtained for GC–MS under selected ion monitoring acquisition are between 0.0038–0.01 and 0.0125–0.033 ng/mL, respectively. The developed method is applicable for the quantification of these compounds in tap water and commercial samples. This method has been shown to be selective as no interferences from endogenous substances were detected by analysis. This method not only decreases sample preparation time but is cheaper, eco‐friendly and easier to perform compared to traditional techniques.     

Multiresidue determination of 29 pesticide residues in pepper through a modified QuEChERS method and gas chromatography–mass spectrometry

This study describes the development and use of a modified quick, easy, cheap, effective, rugged and safe (QuEChERS) method coupled with gas chromatography with mass spectrometry to determine 29 pesticide residues in green, red and dehydrated red peppers. Pesticides were extracted with acetonitrile (1% acetic acid), partitioned with sodium chloride and purified with primary secondary amino and octadecyl silane in acetone. The QuEChERS extraction conditions were optimized, and the matrix effects that might influence recoveries were evaluated and minimized using matrix‐matched calibration curves. Under the optimized conditions, the calibration curves for 29 pesticides showed good linearity in the concentration range of 0.1–10 μg/mL with determination coefficient R² > 0.998. The limits of quantification of the 29 pesticides were 0.006–0.06 mg/kg for green pepper, 0.005–0.039 mg/kg for red pepper and 0.014–0.25 mg/kg for dehydrated red pepper. These values are below the suggested regulatory maximum residue limits. The mean recoveries ranged between 70.1 and 110%, and the relative standard deviations were <13%. The developed method was successfully applied to commercial samples. Some samples were found to contain the 29 pesticides with levels below the legal limits. Copyright © 2016 John Wiley & Sons, Ltd.