Rapid analysis of the essential oil components of dried Zanthoxylum bungeanum Maxim by Fe2O3‐magnetic‐microsphere‐assisted microwave distillation and simultaneous headspace single‐drop microextraction followed by GC–MS

In this work, microwave distillation assisted by Fe₂O₃ magnetic microspheres (FMMS) and headspace single‐drop microextraction were combined, and developed for determination of essential oil compounds in dried Zanthoxylum bungeanum Maxim (ZBM). The FMMS were used as microwave absorption solid medium for dry distillation of dried ZBM. Using the proposed method, isolation, extraction, and concentration of essential oil compounds can be carried out in a single step. The experimental parameters including extraction solvent, solvent volume, microwave power, irradiation time, and the amount of added FMMS, were studied. The optimal analytical conditions were: 2.0 μL decane as the extraction solvent, microwave power of 300 W, irradiation time of 2 min, and the addition of 0.1 g FMMS to ZBM. The method precision was from 4 to 10%. A total of 52 compounds were identified by the proposed method. The conventional steam distillation method was also used for the analysis of essential oil in dried ZBM and only 31 compounds were identified by steam distillation method. It was found that the proposed method is a simple, rapid, reliable, and solvent‐free technique for the determination of volatile compounds in Chinese herbs.     

On‐line ionic liquid‐based dynamic microwave‐assisted extraction‐high performance liquid chromatography for the determination of lipophilic constituents in root of Salvia miltiorrhiza Bunge

On‐line continuous sampling, ionic liquid‐based dynamic microwave‐assisted extraction high performance liquid chromatography has been developed and applied to the extraction of lipophilic constituents from root of Salvia miltiorrhiza Bunge. Several operating parameters were optimized by single‐factor and Box–Behnken design experiments. The type and concentration of ionic liquids, power of microwave irradiation, flow rate of sample suspension, amount, and particle size of sample were investigated. The limits of detection for tanshin‐one I, cryptotanshinone, and tanshinone II_A are 0.014, 0.009, and 0.009 mg/g, respectively. The RSDs of interday and intraday were lower than 2.02 and 2.16%, respectively. The recoveries for target analytes were in the range of 90.7–101.8%. The homogeneity of the suspension and stability of the analytes were investigated and the results were satisfactory. The proposed method was compared with the off‐line ionic liquid‐based dynamic microwave‐assisted extraction, off‐line ethanol‐based dynamic microwave‐assisted extraction, ionic liquid‐based ultrasonic‐assisted extraction, and ionic liquid‐based maceration extraction. The results indicated that the proposed method is effective for the extraction of the active components in Chinese herbal medicine and has some advantages over the other methods.     

Rapid analysis of Fructus forsythiae essential oil by ionic liquids-assisted microwave distillation coupled with headspace single-drop microextraction followed by gas chromatography–mass spectrometry

A rapid, green and effective miniaturized sample preparation and analytical technique, i.e. ionic liquids-assisted microwave distillation coupled with headspace single-drop microextraction (ILAMD-HS-SDME) followed by gas chromatography–mass spectrometry (GC–MS) was developed for the analysis of essential oil (EO) in Fructus forsythiae. In this work, ionic liquids (ILs) were not only used as the absorption medium of microwave irradiation but also as the destruction agent of plant cell walls. 1-Ethyl-3-methylimidazolium acetate ([C₂mim]OAc) was chosen as the optimal ILs. Moreover, n-heptadecane (2.0 μL) was selected as the appropriate suspended solvent for the extraction and concentration of EO. Extraction conditions of the proposed method were optimized using the relative peak area of EO constituents as the index, and the optimal operational parameters were obtained as follows: irradiation power (300 W), sample mass (0.7 g), mass ratio of ILs to sample (2.4), temperature (78 °C) and time (3.4 min). In comparison to previous reports, the proposed method was faster and required smaller sample amount but could equally monitor all EO constituents with no significant differences.     

Temperature‐controlled ionic liquid‐dispersive liquid‐phase microextraction for preconcentration of chlorotoluron,diethofencarb and chlorbenzuron in water samples

This article describes a new, rapid and sensitive method for the determination of chlorotoluron, diethofencarb and chlorbenzuron from water samples with temperature‐controlled ionic liquid‐dispersive liquid‐phase microextraction. In the preconcentration procedure, ionic liquid 1‐hexyl‐3‐methylimidazolium hexafluorophosphate [C₆MIM] [PF₆] was employed as the extraction solvent. The parameters, such as volume of [C₆MIM] [PF₆], sample pH, extraction time, centrifuging time, temperature and salting‐out effect, were investigated in detail. Under the optimal extraction conditions, it has been found that three analytes had excellent LODs (S/N=3) in the range of 0.04–0.43 μg/L. The RSDs (n=6) were in the range of 1.3–4.7%. The proposed method was evaluated with lake water, tap water and melted snow water samples. The experimental results indicated that the proposed method had excellent prospect and would be widely used in the future.     

Ionic liquid‐based headspace in‐tube liquid‐phase microextraction coupled with CE for sensitive detection of phenols

An ionic liquid‐based headspace in‐tube liquid‐phase microextraction (IL‐HS‐ITLPME) in‐line coupled with CE is proposed. The method is capable of quantifying trace amounts of phenols in environmental water samples. In the newly developed method, simply by placing a capillary injected with ionic liquids (IL) in the HS above the aqueous sample, volatile phenols were extracted into the IL acceptor phase in the capillary. After extraction, electrophoresis of the phenols in the capillary was carried out. Extraction parameters such as the extraction time, extraction temperature, ionic strength, volume of the sample solution, and IL types were systematically investigated. Under the optimized conditions, enrichment factors for four phenols were from 1510 to 1985. The proposed method provided a good linearity, low limits of detection (below 5.0 ng/mL), and good repeatability of the extractions (RSDs below 6.7%, n = 6). This method was then utilized to analyze two real environmental samples of Xiaoxi Lake and tap water, obtaining acceptable recoveries and precisions. Compared with the usual HS‐ITLPME for CE, IL‐HS‐ITLPME‐CE is a simple, low cost, fast, and environmentally friendly preconcentration technique.     

Analysis of volatile oil composition of Citrus aurantium L. by microwave‐assisted extraction coupled to headspace solid‐phase microextraction with nanoporous based fibers

Nanoporous silica was prepared and functionalized with amino propyl‐triethoxysilane to be used as a highly porous fiber‐coating material for solid‐phase microextraction (SPME). The prepared nanomaterials were immobilized onto a stainless steel wire for fabrication of the SPME fiber. The proposed fiber was evaluated for the extraction of volatile component of Citrus aurantium L. leaves. A homemade microwave‐assisted extraction followed by headspace (HS) solid‐phase apparatus was used for the extraction of volatile components. For optimization of factors affecting the extraction efficiency of the volatile compounds, a simplex optimization method was used. The repeatability for one fiber (n = 4), expressed as RSD, was between 3.1 and 8.6% and the reproducibility for five prepared fibers was between 10.1 and 14.9% for the test compounds. Using microwave‐assisted distillation HS‐SPME followed by GC‐MS, 53 compounds were separated and identified in C. aurantium L., which mainly included limonene (62.0%), linalool (7.47%), trans‐β‐Ocimene (3.47%), and caryophyllene (2.05%). In comparison to a hydrodistillation method, the proposed technique could equally monitor almost all the components of the sample, in an easier way, which was rapid and required a much lower amount of sample.     

Vortex‐assisted liquid–liquid microextraction for the rapid screening of short‐chain chlorinated paraffins in water

The rapid screening of trace levels of short‐chain chlorinated paraffins in various aqueous samples was performed by a simple and reliable procedure based on vortex‐assisted liquid–liquid microextraction combined with gas chromatography and electron capture negative ionization mass spectrometry. The optimal vortex‐assisted liquid–liquid microextraction conditions for 20 mL water sample were as follows: extractant 400 μL of dichloromethane; vortex extraction time of 1 min at 2500 × g; centrifugation of 3 min at 5000 × g; and no ionic strength adjustment. Under the optimum conditions, the limit of quantitation was 0.05 μg/L. Precision, as indicated by relative standard deviations, was less than 9% for both intra‐ and inter‐day analysis. Accuracy, expressed as the mean extraction recovery, was above 91%. The vortex‐assisted liquid–liquid microextraction with gas chromatography and electron capture negative ionization mass spectrometry method was successfully applied to quantitatively extract short‐chain chlorinated paraffins from samples of river water and the effluent of a wastewater treatment plant, and the concentrations ranged from 0.8 to 1.6 μg/L.     

Design of guanidinium ionic liquid based microwave‐assisted extraction for the efficient extraction of Praeruptorin A from Radix peucedani

A series of novel tetramethylguanidinium ionic liquids and hexaalkylguanidinium ionic liquids have been synthesized based on 1,1,3,3‐tetramethylguanidine. The structures of the ionic liquids were confirmed by ¹H NMR spectroscopy and mass spectrometry. A green guanidinium ionic liquid based microwave‐assisted extraction method has been developed with these guanidinium ionic liquids for the effective extraction of Praeruptorin A from Radix peucedani. After extraction, reversed‐phase high‐performance liquid chromatography with UV detection was employed for the analysis of Praeruptorin A. Several significant operating parameters were systematically optimized by single‐factor and L₉ (3⁴) orthogonal array experiments. The amount of Praeruptorin A extracted by [1,1,3,3‐tetramethylguanidine]CH₂CH(OH)COOH is the highest, reaching 11.05 ± 0.13 mg/g. Guanidinium ionic liquid based microwave‐assisted extraction presents unique advantages in Praeruptorin A extraction compared with guanidinium ionic liquid based maceration extraction, guanidinium ionic liquid based heat reflux extraction and guanidinium ionic liquid based ultrasound‐assisted extraction. The precision, stability, and repeatability of the process were investigated. The mechanisms of guanidinium ionic liquid based microwave‐assisted extraction were researched by scanning electron microscopy and IR spectroscopy. All the results show that guanidinium ionic liquid based microwave‐assisted extraction has a huge potential in the extraction of bioactive compounds from complex samples.     

Application of ionic liquid‐based microwave‐assisted extraction of malachite green and crystal violet from water samples

A simple, environment friendly and efficient technique, ionic liquid‐based microwave‐assisted extraction was first used to determine malachite green and crystal violet (CV) from water samples coupled to HPLC. The key parameters influencing extraction efficiency were investigated, such as the type of ionic liquids, the volume of ionic liquid, extraction time, and so on. Under the optimum conditions, good reproducibility of the extraction performance was obtained (RSD, 1.0% for malachite green (MG) and 5.9% for CV, n = 5). Good linearity (0.10–25 μg L^?1) was observed with correlation coefficients between 0.9991 and 0.9964. The detection limits of MG and CV were 0.080 and 0.030 μg L^?1, respectively. The proposed method had been successfully applied to determine MG and CV in real water samples with recoveries ranging from 95.4 to 102.8%. Compared with the previous technologies, the proposed method required less extraction time (2 min), and provided lower detection limits and higher enrichment factors. Moreover, there were no volatile and hazardous organic solvents released. Based on these simple, environment friendly, rapid, and highly efficient results, the proposed approach provides a new and promising alternative for simultaneously extracting trace amounts of MG and CV from water.     

Low‐density‐solvent‐based air‐assisted liquid–liquid microextraction followed by gas chromatography with flame ionization detection for the determination of synthetic phenolic antioxidants in milk samples

A simple and rapid sample pretreatment technique termed low‐density‐solvent‐based air‐assisted liquid–liquid microextraction has been developed for the extraction and preconcentration of three synthetic phenolic antioxidants including butylated hydroxyanisole, butylated hydroxytoluene, and tert‐butyl hydroquinone from milk samples prior to their analysis by gas chromatography with flame ionization detection. In this method, initially trichloroacetic acid as a proteins precipitation agent is added to the sample, and then it is sonicated and centrifuged. The obtained aqueous phase is removed and the analytes extracted by the proposed method using a low‐density organic solvent. Some important parameters such as type and volume of extraction solvent, ionic strength, pH, and centrifugation rate and time were studied. Under the optimum conditions, enrichment factors were obtained in the range of 501–614. LODs and quantification were between 0.76–1.16 and 2.66–3.96 ng mL^–1, respectively. This method is rapid and requires less than 15 min for sample preparation.     

Rapid Extraction of Essential Oil from Dried Cinnamomum cassia Presl and Forsythia suspensa(Thunb.)Vahl by Ionic Liquid Microwave Extraction

Ionic liquid (IL) was used as the microwave absorption medium to extract essential oils from dried Cinnamomum cassia Presl and Forsythia suspensa (Thunb.) Vahl, and the ionic liquid microwave extraction (ILME) was developed. Some experimental parameters for ILME were examined. The proposed method was compared with other methods, including hydrodistillation (HD), microwave hydrodistillation (MHD), solvent‐free microwave extraction (SFME) and improved solvent‐free microwave extraction (ISFME). Experimental results showed that compared with other extraction methods the ILME had some advantages, such as time‐saving, simplicity and usage of green solvents. The extraction time was less than 18 min at the microwave power of 440 W and 1.5 mL of ionic liquid was required. The constituents of essential oils obtained by the five methods are not obviously different.     

Use of volatile organic solvents in headspace liquid‐phase microextraction by direct cooling of the organic drop using a simple cooling capsule

A low‐cost and simple cooling‐assisted headspace liquid‐phase microextraction device for the extraction and determination of 2,6,6‐trimethyl‐1,3 cyclohexadiene‐1‐carboxaldehyde (safranal) in Saffron samples, using volatile organic solvents, was fabricated and evaluated. The main part of the cooling‐assisted headspace liquid‐phase microextraction system was a cooling capsule, with a Teflon microcup to hold the extracting organic solvent, which is able to directly cool down the extraction phase while the sample matrix is simultaneously heated. Different experimental factors such as type of organic extraction solvent, sample temperature, extraction solvent temperature, and extraction time were optimized. The optimal conditions were obtained as: extraction solvent, methanol (10 μL); extraction temperature, 60°C; extraction solvent temperature, 0°C; and extraction time, 20 min. Good linearity of the calibration curve (R² = 0.995) was obtained in the concentration range of 0.01–50.0 μg/mL. The limit of detection was 0.001 μg/mL. The relative standard deviation for 1.0 μg/mL of safranal was 10.7% (n = 6). The proposed cooling‐assisted headspace liquid‐phase microextraction device was coupled (off‐line) to high‐performance liquid chromatography and used for the determination of safranal in Saffron samples. Reasonable agreement was observed between the results of the cooling‐assisted headspace liquid‐phase microextraction high‐performance liquid chromatography method and those obtained by a validated ultrasound‐assisted solvent extraction procedure.     

Microwave‐assisted extraction and rapid isolation of ursolic acid from the leaves of Eucalyptus × hybrida Maiden and its quantification using HPLC‐diode array technique

Ursolic acid (UA) is the most important bioactive phytoconstituent of Eucalyptus × hybrida Maiden leaves and exhibits anticancer, antimutagenic, anti‐inflammatory, antioxidative, and antiprotozoal activities. In this study, microwave‐assisted extraction technique was employed for rapid isolation of UA from the leaves of Eucalyptus × hybrida and simultaneously HPLC‐diode array method was developed for the quantification of UA. Effects of several experimental parameters on the extraction efficiencies of UA, such as type and volume of extraction solvents, microwave power and extraction time, were evaluated. The optimal extraction conditions were found to be 20 mL of a mixture of chloroform/methanol, 60:40; liquid‐to‐material ratio, 4:1; preleaching time, 10 min; microwave power, 600 W; temperature, 50°C; and microwave irradiation time, 5 min. Under the optimum conditions, the yield of UA was found to be 1.95 ± 0.08% in the dry leaves of Eucalyptus × hybrida. The results showed that microwave‐assisted extraction is a more rapid extraction method with higher yield and lower solvent consumptions than the conventional method. It is a faster, convenient, and appropriate method and it may be used for rapid isolation and quantification of UA and other important phytoconstituents present in the leaves of Eucalyptus × hybrida.     

Monitoring the oleuropein content of olive leaves and fruits using ultrasound‐ and salt‐assisted liquid–liquid extraction optimized by response surface methodology and high‐performance liquid chromatography

A novel and rapid ultrasound‐ and salt‐assisted liquid–liquid extraction coupled with high‐performance liquid chromatography has been optimized by response surface methodology for the determination of oleuropein from olive leaves. Box–Behnken design was used for optimizing the main parameters including ultrasound time (A), pH (B), salt concentration (C), and volume of miscible organic solvent (D). In this technique, a mixture of plant sample and extraction solvent was subjected to ultrasound waves. After ultrasound‐assisted extraction, phase separation was performed by the addition of salt to the liquid phase. The optimal conditions for the highest extraction yield of oleuropein were ultrasound time, 30 min; volume of organic solvent, 2.5 mL; salt concentration, 25% w/v; and sample pH, 4. Experimental data were fitted with a quadratic model. Analysis of variance results show that BC interaction, A², B², C², and D² are significant model terms. Unlike the conventional extraction methods for plant extracts, no evaporation and reconstitution operations were needed in the proposed technique.     

Application of ionic liquid‐based surfactants in the microwave‐assisted extraction for the determination of four main phloroglucinols from Dryopteris fragrans

An ionic liquid‐based surfactant combined with microwave‐assisted extraction method, followed by RP‐HPLC‐diode array detection (DAD) with a core shell column, was successfully applied in extracting and quantifying four major phloroglucinols from Dryopteris fragrans. Eight ionic liquids with different cation and anion were investigated, and 1‐octyl‐3‐methylimidazolium bromide presented the best relative extraction efficiency for four phloroglucinols. The optimum conditions of this method were as follows: ionic liquid concentration 0.75 M, liquid/solid ratio 12:1 mL/g, extraction time 7 min, extraction temperature 50°C, and irradiation power 600 W. The quality analytical parameters of the method were obtained based on the linearity, precision, accuracy, detection, and quantification limits. The recoveries were between 96.90 and 103.5% with standard deviations not higher than 4.7%. Compared with ionic liquid‐based heat reflux extraction, ultrasonic‐assisted extraction, negative‐pressure cavitation extraction, and conventional microwave‐assisted extraction, the relative extraction efficiencies of the proposed method for four phloroglucinols increased 1.5–40.4%. The method was successfully applied for the quantification of four major phloroglucinols from D. fragrans. All these results suggest that the developed method represents an excellent alternative for the extraction and quantification of phloroglucinols in other plant materials.     

Rapid analysis of ultraviolet filters using dispersive liquid–liquid microextraction coupled to headspace gas chromatography and mass spectrometry

An ionic‐liquid‐based in situ dispersive liquid–liquid microextraction method coupled to headspace gas chromatography and mass spectrometry was developed for the rapid analysis of ultraviolet filters. The chemical structures of five ionic liquids were specifically designed to incorporate various functional groups for the favorable extraction of the target analytes. Extraction parameters including ionic liquid mass, molar ratio of ionic liquid to metathesis reagent, vortex time, ionic strength, pH, and total sample volume were studied and optimized. The effect of the headspace temperature and volume during the headspace sampling step was also evaluated to increase the sensitivity of the method. The optimized procedure is fast as it only required ∼7–10 min per extraction and allowed for multiple extractions to be performed simultaneously. In addition, the method exhibited high precision, good linearity, and low limits of detection for six ultraviolet filters in aqueous samples. The developed method was applied to both pool and lake water samples attaining acceptable relative recovery values.     

Microwave-Assisted Extraction/Dispersive Liquid–Liquid Microextraction Coupled with DSI-GC-IT/MS for Analysis of Essential Oil from Three Species of Cardamom

A novel method of microwave-assisted extraction coupled with polyethylene Pasteur-pipette-based dispersive liquid–liquid microextraction applying low-density organic solvent (MAE-LDS-DLLME) was successfully developed for extraction and preconcentration of essential oil from three species of cardamom (Semen Alpiniae Katsumadai, Fructus Amomi Rotundus, and Semen Myristicae). The essential oil was analyzed by gas chromatography-ion trap/mass spectrometry (GC-IT/MS) using a ChromatoProbe direct sample introduction (DSI) device. The effects of various parameters affecting the extraction process, such as the type of extraction solvent and dispersive solvent, ionic strength, microwave power, and irradiation time, were investigated thoroughly and optimized. The optimal conditions were extraction solvent of toluene, dispersive solvent of methanol, microwave power of 80 W, irradiation time of 4.0 min, plant material amount of 0.1 g, and no addition of salt. Compared with hydrodistillation, MAE-DLLME-DSI-GC–MS is a simple, rapid, low-cost, efficient, and environmentally friendly method, and the essential oil contains higher amounts of oxygenated compounds, which play an important and valuable role in terms of their contribution to the fragrance of the essential oil. In this work, we also studied the main components of the three varieties of cardamom. Qualitative and quantitative differences in the components of the three essential oils were found to be present. Based on comparison of the main bioactive compounds of essential oil, a significant difference was found between Semen Alpiniae Katsumadai or Fructus Amomi Rotundus and Semen Myristicae. This study also provides a new approach for quality assessment of traditional Chinese medicines.     

Ionic‐liquid‐based ultrasound/microwave‐assisted extraction of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one from maize (Zea mays L.) seedlings

We evaluated an ionic‐liquid‐based ultrasound/microwave‐assisted extraction method for the extraction of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one from etiolated maize seedlings. We performed single‐factor and central composite rotatable design experiments to optimize the most important parameters influencing this technique. The best results were obtained using 1.00 M 1‐octyl‐3‐methylimidazolium bromide as the extraction solvent, a 50°C extraction temperature, a 20:1 liquid/solid ratio (mL/g), a 21 min treatment time, 590 W microwave power, and 50 W fixed ultrasonic power. We performed a comparison between ionic‐liquid‐based ultrasound/microwave‐assisted extraction and conventional homogenized extraction. Extraction yields of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one by the ionic‐liquid‐based ultrasound/microwave‐assisted extraction method were 1.392 ± 0.051 and 0.205 ± 0.008 mg/g, respectively, which were correspondingly 1.46‐ and 1.32‐fold higher than those obtained by conventional homogenized extraction. All the results show that the ionic‐liquid‐based ultrasound/microwave‐assisted extraction method is therefore an efficient and credible method for the extraction of 2,4‐dihydroxy‐7‐methoxy‐1,4‐benzoxazin‐3‐one and 6‐methoxy‐benzoxazolin‐2‐one from maize seedlings.     

Polydimethylsiloxane/graphene oxide/β-cyclodextrin sponge as a solid-phase extraction sorbent coupled with gas chromatography-mass spectrometry for rapid adsorption and sensitive determination of lavender essential oil

An adsorbent polydimethylsiloxane/graphene oxide/β-cyclodextrin sponge, which possessed the merits of high surface area, chemical stability, environment friendly, and excellent extraction capacity, was successfully fabricated. Based on the advantages, a novel microwave-assisted headspace solid-phase extraction method for lavender essential oil using polydimethylsiloxane/graphene oxide/β-cyclodextrin sponge as adsorbents was developed in this study. Various experimental parameters were studied. The optimal extraction conditions were as follows: 1 mg/mL as dopamine solution concentration, graphene oxide dosages of 30 mg, microwave power of 700 W, microwave irradiation time of 10 min, and desorption solvent of n-hexane. Under the optimal extraction condition, linearities ranging from 10 to 800 ng were achieved for six representative compounds with a correlation coefficients value of >0.99. The intra-day and inter-day precisions were in the ranges of 0.40–1.56 and 0.67–2.56%, respectively. Finally, the proposed technique was applied to analyze essential oil constituents in 14 samples of three lavender varieties, and 48 compounds were identified. Lavender varieties were distinguished using principal component analysis and partial least squares discriminant analysis. The results showed that the method developed in this study is a novel, simple, and sensitive method for the determination of essential oil in complex plant samples.     

Ionic‐liquid‐based dispersive liquid–liquid microextraction combined with magnetic solid‐phase extraction for the determination of aflatoxins B1, B2, G1, and G2 in animal feeds by high‐performance liquid chromatography with fluorescence detection

A novel two‐step extraction technique combining ionic‐liquid‐based dispersive liquid–liquid microextraction with magnetic solid‐phase extraction was developed for the preconcentration and separation of aflatoxins in animal feedstuffs before high‐performance liquid chromatography coupled with fluorescence detection. In this work, ionic liquid 1‐octyl‐3‐methylimidazolium hexafluorophosphate was used as the extractant in dispersive liquid–liquid microextraction, and hydrophobic pelargonic acid modified Fe₃O₄ magnetic nanoparticles as an efficient adsorbent were applied to retrieve the aflatoxins‐containing ionic liquid. Notably, the target of magnetic nanoparticles was the ionic liquid rather than the aflatoxins. Because of the rapid mass transfer associated with the dispersive liquid–liquid microextraction and magnetic solid phase steps, fast extraction could be achieved. The main parameters affecting the extraction recoveries of aflatoxins were investigated and optimized. Under the optimum conditions, vortexing at 2500 rpm for 1 min in the dispersive liquid–liquid microextraction and magnetic solid‐phase extraction and then desorption by sonication for 2 min with acetonitrile as eluent. The recoveries were 90.3–103.7% with relative standard deviations of 3.2–6.4%. Good linearity was observed with correlation coefficients ranged from 0.9986 to 0.9995. The detection limits were 0.632, 0.087, 0.422 and 0.146 ng/mL for aflatoxins B₁, B2, G1, and G2, respectively. The results were also compared with the pretreatment method carried out by conventional immunoaffinity columns.