LiNi1/3Co1/3Mn1/3O2 cathode materials for LIB prepared by spray pyrolysis I: the spectral, structural, and electro-chemical properties

Layered lithium ion battery cathode material LiNi_1/3Co_1/3Mn_1/3O₂ with uniform particle size of about 6 μm was synthesized by a spray pyrolysis method. Infrared and X-ray diffraction analyses show that the pyrolysis at 1,000 °C for 2 s in the tube furnace eliminates nearly all the organic components but is still not enough for the complete crystallization of LiNi_1/3Co_1/3Mn_1/3O₂ materials. Therefore, further annealing at 850 °C is needed. The prepared LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials show excellent electrochemical performances. By increasing the C-rates, the cell shows discharge capacities of 159.3, 148.2, 133.7, and 125.7 mAh g^?1 at 0.1, 0.2, 0.5, and 1C rates, respectively. Only 2.1 mAh g^?1 capacity loss is observed when back to 0.1C rate. Moreover, LiNi_1/3Co_1/3Mn_1/3O₂ cathode retains 96, 97.7, 97.1, 94.5, and 97.1 % of its initial discharge capacities after 20 cycles at 0.1, 0.2, 0.5, 1, and back to 0.1C rates, respectively. More than 97 % coulombic efficiencies are observed at all the current densities in 20 cycles.     

ZrO2 coating of LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ materials were prepared by hydroxide precipitation. The structure and electrochemical properties of the ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ were investigated using X-ray diffraction, scanning electron microscope, and charge–discharge tests, indicating that the lattice structure of LiNi_1/3Co_1/3Mn_1/3O₂ were unchanged after the coating but the cycling stability was improved. As the coating amount increased from 0.0 to 0.5 mol.%, the initial capacity of the coated LiNi_1/3Co_1/3Mn_1/3O₂ decreased slightly; however, the cycling stability increased remarkably over the cut-off voltages of 2.5~4.3 V and the capacity retention reached 99.5% after 30 cycles at the coating amount of 0.5 mol.%. ZrO₂ coating also improved the cycling stability of LiNi_1/3Co_1/3Mn_1/3O₂ over wider cut-off voltage of 2.5~4.6 V.     

Modification research of LiAlO<Subscript>2</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a cathode material for lithium-ion battery

The LiNi_0.8Co_0.1Mn_0.1O₂ with LiAlO₂ coating was obtained by hydrolysis–hydrothermal method. The morphology of the composite was characterized by SEM, TEM, and EDS. The results showed that the LiAlO₂ layer was almost completely covered on the surface of particle, and the thickness of coating was about 8–12 nm. The LiAlO₂ coating suppressed side reaction between composite and electrolyte; thus, the electrochemical performance of the LiAlO₂-coated LiNi_0.8Co_0.1Mn_0.1O₂ was improved at 40 °C. The LiAlO₂-coated sample delivered a high discharge capacity of 181.2 mAh g^?1 (1 C) with 93.5% capacity retention after 100 cycles at room temperature and 87.4% capacity retention after 100 cycles at 40 °C. LiAlO₂-coated material exhibited an excellent cycling stability and thermal stability compared with the pristine material. These works will contribute to the battery structure optimization and design.     

Enhanced electrochemical properties and thermal stability of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by surface modification with Eu<Subscript>2</Subscript>O<Subscript>3</Subscript>

Layered LiNi_1/3Co_1/3Mn_1/3O₂ cathode material is synthesized via a sol-gel method and subsequently surface-modified with Eu₂O₃ layer by a wet chemical process. The effect of Eu₂O₃ coating on the electrochemical performances and thermal stability of LiNi_1/3Co_1/3Mn_1/3O₂@Eu₂O₃ cells is investigated systematically by the charge/discharge testing, cyclic voltammograms, AC impedance spectroscopy, and DSC measurements, respectively. In comparison, the Eu₂O₃-coated sample demonstrates better electrochemical performances and thermal stability than that of the pristine one. After 100 cycles at 1C, the Eu₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode demonstrates stable cyclability with capacity retention of 92.9 %, which is higher than that (75.5 %) of the pristine one in voltage range 3.0–4.6 V. Analysis from the electrochemical measurements reveals that the remarkably improved performances of the surface-modified composites are mainly ascribed to the presence of Eu₂O₃-coating layer, which could efficiently suppress the undesirable side reaction and increasing impedance, and enhance the structural stability of active material.     

An investigation on the unsatisfactory rate capability of spherical LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> particles prepared by using Na<Subscript>2</Subscript>CO<Subscript>3</Subscript> as a precipitant

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ particles were successfully synthesized using Na₂CO₃ as a precipitant. Electrochemical measurements indicate that the as-synthesized spherical particles deliver a high reversible capacity of above 180 mAh g^?1 at 0.1 C in the voltage range of 2.8–4.4 V and display an excellent cyclic performance at 0.5 C. However, unsatisfactory rate capability was detected for the as-prepared spherical particles. The reason for the unsatisfactory rate capability was investigated through a comparison of the properties of the as-synthesized spherical particles versus the ball-milled samples via a combination of specific surface areas test, electronic conductivity measurement, and electrochemical impedance spectroscopy. The results show that both the rate capabilities of cathode materials and the electronic conductivities of the mixtures of active material, conductive additive, and binder are highly improved when the secondary spherical particles were broken, indicating that the poor electronic conductivity of electrode caused by the large secondary spherical particles with a great amount of nano-pores is a significant factor for the unsatisfactory rate capability.     

Studies of the electrochemical properties and thermal stability of LiNi1/3Co1/3Mn1/3O2/LiFePO4 composite cathodes for lithium ion batteries

A series of LiNi_1/3Co_1/3Mn_1/3O₂/LiFePO₄ composite cathodes with the LiFePO₄ mass content ranging from 10 to 30 wt% were prepared by ball milling in order to combine the merits of layered LiNi_1/3Co_1/3Mn_1/3O₂ and olivine LiFePO₄. The structure and morphology of the samples were characterized by X-ray diffraction and scanning electron microscope. The composite cathodes exhibited improved electrochemical performance compared with pristine LiNi_1/3Co_1/3Mn_1/3O₂. Among all the composite cathodes, the one with 20 wt% of LiFePO₄ showed the best electrochemical performance in terms of discharge capacity, cycle stability, and rate capability. Electrochemical impedance spectroscopy showed that mixing of LiFePO₄ in LiNi_1/3Co_1/3Mn_1/3O₂ decreased the internal resistance of the electrode, retarded the formation of SEI film, and facilitated the charge transfer reaction. Differential scanning calorimetry showed that the composite cathode had better thermal stability than pristine LiNi_1/3Co_1/3Mn_1/3O₂.     

TiO2 coating of LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

TiO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ materials were prepared by the hydrolyzation of Ti(OBu)₄. The impact of TiO₂ coating on the structure and electrochemical properties of LiNi_1/3Co_1/3Mn_1/3O₂ was investigated using X-ray diffraction, scanning electron microscope, and charge–discharge tests. The results indicated that TiO₂ coating did not affect the lattice of LiNi_1/3Co_1/3Mn_1/3O₂, but exhibited obvious effects on its discharge capacity and cycling stability. As coated TiO₂ increased from 0.0 to 2.0 mol%, the initial capacity of samples decreased slightly, but the cycling stability over 2.5∼4.3 V increased remarkably. The capacity retention reached 99.5% at the 50th cycle at a coating amount of 2.0 mol%.     

The optimized preparation and electrochemical properties of LiMn1.95Co0.05O4 and Al2O3-coated LiMn1.95Co0.05O4

Cathode material LiMn_1.95Co_0.05O₄ for lithium ion battery was synthesized via solid state reaction, and calcination temperature and time were investigated, respectively. Thermogravimetry (TG) and differential thermal analysis (DTA) measurements were utilized to determine the calcination temperature of precursor sample. The optimized calcination temperature and time are 850 °C and 15 h. The surface of LiMn_1.95Co_0.05O₄ cathode is coated using Al₂O₃ coating materials. The phase structures, surface morphologies, and element types of the prepared LiMn_1.95Co_0.05O₄ and Al₂O₃-coated LiMn_1.95 Co_0.05O₄ were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and energy spectrum analysis (EDS). The 0.5 wt% Al₂O₃-coated compound exhibited better specific capacity and capacity retention than bare sample. The initial discharge capacity was 140.9 mAh/g and capacity retention was 96.7 % after 10 cycles at 0.1 C. Such enhancements are attributed to the presence of a stable Al₂O₃ layer which acts as the interfacial stabilizer on the surface of LiMn_1.95Co_0.05O₄.     

Characterization of Na-substituted LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium-ion battery

Highly crystalline layered Li_1?xNa_xNi_1/3Co_1/3Mn_1/3O₂ (x?=?0, 0.001, 0.01, 0.03, 0.05) materials are synthesized by molten salts method and characterized by scanning electron microscopy, inductively coupled plasma (ICP), X-ray diffraction, Rietveld refinement, and electrochemical measurement, respectively. ICP, SEM, and EDS results show that Na ions are incorporated in LiNi_1/3Co_1/3Mn_1/3O₂. Rietveld refinement results show that suitable Na substitution leads to stable layered structure by full Na occupying in Li layer and further attributes to low cation mixing. Electrochemical studies demonstrate that the Na-substituted LiNi_1/3Co_1/3Mn_1/3O₂ shows improved rate capability and cycling performance compared to that of pure LiNi_1/3Co_1/3Mn_1/3O₂.     

Improving the rate performance and stability of LiNi<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>O<Subscript>2</Subscript> in high voltage lithium-ion battery by using fluoroethylene carbonate as electrolyte additive

Fluoroethylene carbonate (FEC) is investigated as the electrolyte additive to improve the electrochemical performance of high voltage LiNi_0.6Co_0.2Mn_0.2O₂ cathode material. Compared to LiNi_0.6Co_0.2Mn_0.2O₂/Li cells in blank electrolyte, the capacity retention of the cells with 5 wt% FEC in electrolytes after 80 times charge-discharge cycle between 3.0 and 4.5 V significantly improve from 82.0 to 89.7%. Besides, the capacity of LiNi_0.6Co_0.2Mn_0.2O₂/Li only obtains 12.6 mAh g^?1 at 5 C in base electrolyte, while the 5 wt% FEC in electrolyte can reach a high capacity of 71.3 mAh g^?1 at the same rate. The oxidative stability of the electrolyte with 5 wt% FEC is evaluated by linear sweep voltammetry and potentiostatic data. The LSV results show that the oxidation potential of the electrolytes with FEC is higher than 4.5 V vs. Li/Li⁺, while the oxidation peaks begin to appear near 4.3 V in the electrolyte without FEC. In addition, the effect of FEC on surface of LiNi_0.6Co_0.2Mn_0.2O₂ is elucidated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The analysis result indicates that FEC facilitates the formation of a more stable surface film on the LiNi_0.6Co_0.2Mn_0.2O₂ cathode. The electrochemical impedance spectroscopy (EIS) result evidences that the stable surface film could improve cathode electrolyte interfacial resistance. These results demonstrate that the FEC can apply as an additive for 4.5 V high voltage electrolyte system in LiNi_0.6Co_0.2Mn_0.2O₂/Li cells.     

Simple co-precipitation synthesis of high-voltage spinel cathodes with different Ni/Mn ratios for lithium-ion batteries

The high-voltage spinel is a promising cathode material in next generation of lithium-ion batteries. Samples LiNi_0.5???xMn_1.5?+?xO₄ (x?=?0, 0.05, 0.1) are synthesized by a simple co-precipitation method, in which pH value and temperature conditions do not need control. In the simple co-precipitation method, NaHCO₃ solution is poured into transition metal solution to produce precursor. Ni and Mn are distributed uniformly in the products. The as-prepared samples are composed of ~?200 nm primary particles. Samples LiNi_0.5???xMn_1.5?+?xO₄ (x?=?0, 0.05, 0.1) are also tested to study the effects of different Ni/Mn ratios. Sample LiNi_0.5Mn_1.5O₄ delivers discharge capacities of 130 mAh g^?1 at 0.2 C. The decreasing of Ni/Mn ratio in samples reduces specific capacity. With the decreasing of Ni/Mn ratios in spinel, amount of Mn³⁺ are increased. Attributed to its high Mn³⁺ contents, sample LiNi_0.4Mn_1.6O₄ delivers the highest discharge capacity of 106 mAh g^?1 at a large current density of 15 C, keeping 84.5% of that at 0.2 C rate. With the increasing of Ni/Mn ratios in spinel, cycling performance is improved. Sample LiNi_0.5Mn_1.5O₄ shows the best cycling stability, keeping 94.4% and 90.4% of the highest discharge capacities after 500 cycles at 1 C and 1000 cycles at 5 C.     

LiNi1/3Co1/3Mn1/3O2 cathode materials for LIB prepared by spray pyrolysis. II. Li+ diffusion kinetics

Layered lithium ion battery cathode material LiNi_1/3Co_1/3Mn_1/3O₂ with a uniform particle size of about 6 μm was synthesized by a spray pyrolysis method. The lithium ion diffusion kinetics in LiNi_1/3Co_1/3Mn_1/3O₂ composite cathode were systematically studied by the ratio of potentio-charge capacity to galvano-charge capacity method, galvanostatic intermittent titration technique, electrochemical impedance spectroscopy, and potential step chronoamperometry methods. The variations of lithium ion diffusion coefficients obtained by the four methods show a close similarity. They vary in the range of 10^?8 to 10^?10 cm² s^?1, with a maximum at 4.1- to 4.2-V voltage level.     

Synthesis of spherical LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ was successfully prepared by controlled crystallization. The preparation started with the spherical coprecipitate of Ni_1/3Co_1/3Mn_1/3CO₃ from NiSO₄, CoSO₄, MnSO₄, NH₄HCO₃, and NH₃·H₂O, followed by pyrolysis of Ni_1/3Co_1/3Mn_1/3CO₃ at 600°C for 3 h. The X-ray diffraction analysis showed that the homogeneous cubic (Ni_1/3Co_1/3Mn_1/3)₃O₄ was obtained after the pyrolysis. Spherical LiNi_1/3Co_1/3Mn_1/3O₂ was obtained by sintering of the mixture of as-obtained (Ni_1/3Co_1/3Mn_1/3)₃O₄ and LiOH·H₂O at 900°C for 6 h in air. As-prepared spherical LiNi_1/3Co_1/3Mn_1/3O₂ presented initial discharge capacity of 162.9 mA h g⁻¹ and capacity retention of 98% at 50th cycle.     

Structural and electrochemical properties of LiNi1/3Co1/3Mn1/3O2 material prepared by a two-step synthesis via oxalate precursor

LiNi_1/3Co_1/3Mn_1/3O₂ (LNMCO) powders were formed by a two-step synthesis including preparation of an oxalate precursor by ??chimie douce?? followed by a solid-state reaction with lithium hydroxide. The product was characterized by TG-DTA, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR), Raman spectroscopy, electron spin resonance (ESR), and SQUID magnetometry. XRD data revealed well-crystallized layered LNMCO with ??-NaFeO₂-type structure (R-3?m space group). Morphology studied by SEM and TEM shows submicronic particles of 400?C800?nm with a tendency to agglomerate. The local structure investigated by vibrational spectroscopy (FTIR, Raman), ESR, and SQUID measurements confirms the well-crystallized lattice with a cation disorder of 2.6% Ni²⁺ ions in Li(3b) sites. Electrochemical tests were carried out in the potential range 2.5?C4.5?V vs. lithium metal on samples heated at 900?°C for 12?h. Initial discharge capacity is 154 mAh/g at C/5, while a capacity of 82 mAh/g is still delivered at 10 C by the two-step synthesized LiNi_1/3Co_1/3Mn_1/3O₂ as cathode material.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

The intercalation/deintercalation kinetic studies on the structure-integrated cathode material 0.5Li2MnO3 0.5LiNi0.5Mn0.5O2

A cathode material, 0.5Li₂MnO₃ 0.5LiNi_0.5Mn_0.5O₂, was prepared by citric acid-assisted sol–gel method and its electrochemical performance was investigated. It delivered a charge capacity of 270 mAh g^?1 and a discharge capacity of 189 mAh g^?1 in the first cycle. With the increase of current density from 14 to 28 mA g^?1, the discharge capacity dropped severely to 130 mA g^?1. Obviously, the rate capability of the material was inferior to most of the oxide cathode materials. The diffusion coefficient of this material was calculated to be 6.04?×?10^?12 cm² s^?1 from the results of cyclic voltammetry measurements. Moreover, diffusion coefficients between 3.13?×?10^?12 and 1.22?×?10^?10 cm² s^?1 in the voltage range of 3.8–4.7 V were obtained by capacity intermittent titration technique. This, together with the localized Li₂MnO₃ domains in the crystal structure, may validate the poor rate capability.     

Suppression of structural degradation of LiNi0.9Co0.1O2 cathode at 90 °C by AlPO4-nanoparticle coating

This study examined the electrochemical and structural stability of ∼1.5 wt.% AlPO₄-coated LiNi_0.9Co_0.1O₂. The AlPO₄-coated LiNi_0.9Co_0.1O₂ retained ∼60% of the original capacity after 50 cycles, compared with the ∼30% capacity retention of the bare LiNi_0.9Co_0.1O₂. The discharge profiles and cyclic voltammograms from 4.5 V at 90 °C for 4 h showed enhanced structural stability. Scanning electron microscopy and X-ray diffraction revealed that the AlPO₄-coated LiNi_0.9Co_0.1O₂ had less degradation than the bare LiNi_0.9Co_0.1O₂.     

Roles of Al-doped ZnO (AZO) modification layer on improving electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> thin film cathode

Al-doped ZnO (AZO) was sputtered on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ (NCM) thin film electrode via radio frequency magnetron sputtering, which was demonstrated to be a useful approach to enhance electrochemical performance of thin film electrode. The structure and morphology of the prepared electrodes were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer, and transmission electron microscopy techniques. The results clearly demonstrated that NCM thin film showed a strong (104) preferred orientation and AZO was uniformly covered on the surface of NCM electrode. After 200 cycles at 50 μA μm^?1 cm^?2, the NCM/AZO-60s electrode delivered highest discharge capacity (78.1 μAh μm^?1 cm^?2) compared with that of the NCM/AZO-120s electrode (62.4 μAh μm^?1 cm^?2) and the bare NCM electrode (22.3 μAh μm^?1 cm^?2). In addition, the rate capability of the NCM/AZO-60s electrode was superior to the NCM/AZO-120s and bare NCM electrodes. The improved electrochemical performance can be ascribed to the appropriate thickness of the AZO coating layer, which not only acted as HF scavenger to keep a stable electrode/electrolyte interface but also reduced the charge transfer resistance during cycling.     

Surface-modified Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> nanoparticles with LaF<Subscript>3</Subscript> as cathode for Li-ion battery

The LaF₃-coated Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ nanoparticles were synthesized via co-precipitation method followed by simple chemical deposition process. The crystal structure, particle morphology, and electrochemical properties of the bare and coated materials were studied by XRD, SEM, TEM, charge–discharge tests. The results showed that the surface coating on Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ nanoparticles were amorphous LaF₃ layer with a thickness of about 10–30 nm. After the surface modification with LaF₃ films, the coating layer served as a protective layer to suppress the side reaction between the positive electrode and electrolyte, and the Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ oxide demonstrated the improved electrochemical properties. The LaF₃-coated Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ electrode delivered the capacities of 270.5, 247.9, 197.1, 170.0, 142.7, and 109.5 mAh g^?1 at current rates of 0.1, 0.2, 0.5, 1, 2, and 5 C rate, respectively. Besides, the capacity retention was increased from 85.1 to 94.8 % after 100 cycles at 0.5 C rate. It implied surface modification with LaF₃ played an important role to improve the cyclic stability and rate capacity of the Li-rich nickel manganese oxides.     

Improved electrochemical properties of YF<Subscript>3</Subscript>-coated Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> as cathode for Li-ion batteries

Yttrium fluoride YF₃ layer with different coating contents is successfully covered on the surface of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ via a common wet chemical approach. The XRD, SEM, TEM, and charge-discharge tests are applied to investigate the influence of YF₃ layer on the micro-structural, morphology, and electrochemical properties of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂. And the electrochemical test results demonstrate that the YF₃-coated LMNCO samples exhibit the improved electrochemical properties. The 2wt.%YF₃-coated LMNCO delivers a discharge capacity of 116.6 mAh g^?1 at 5 C rate, much larger than that (95.6 mAh g^?1) of the pristine one. Besides, the electrochemical impedance spectroscopy (EIS) and cyclic voltammetric results indicate that the YF₃ coating layer can promote the optimization formation of SEI film and reversibility of the electrochemical redox.