Ab initio studies on n-type and p-type Li4Ti5O12

This paper studies the structure and electronic properties of Li4Ti5O12, as anode material for lithium ion batteries, from first principles calculations. The results suggest that there are two kinds of unit cell of Li4Ti5O12: n-type and p-type. The two unit cells have different structures and electronic properties:the n-type with two 16d site Li ions is metallic by electron, while the p-type with three 16d Li ions is metallic by hole. However, the Li4Ti5O12 is an insulator. It is very interesting that one n-type cell and two p-type cells constitute one Li4Ti5O12 supercell which is insulating. The results show that the intercalation potential obtained with a p-type unit cell with one additional electron is quite close to the experimental value of 1.5 V.     

Recent development and application of Li4Ti5O12 as anode material of lithium ion battery

Lithium-ion batteries with both high power and high energy density are one of the promising power sources for electric devices, especially for electric vehicles (EV) and other portable electric devices. One of the challenges is to improve the safety and electrochemical performance of lithium ion batteries anode materials. Li₄Ti₅O₁₂ has been accepted as a novel anode material of power lithium ion battery instead of carbon because it can release lithium ions repeatedly for recharging and quickly for high current. However, Li₄Ti₅O₁₂ has an insulating character due to the electronic structure characterized by empty Ti 3d-states, and this might result in the insufficient applications of LTO at high current discharge rate before any materials modifications. This review focuses first on the present status of Li₄Ti₅O₁₂ including the synthesized method, doping, surface modification, application and theoretical calculation, then on its near future development.     

Significant effect of electron transfer between current collector and active material on high rate performance of Li4Ti5O12

The rate and cycling performances of the electrode materials are affected by many factors in a practical complicated electrode process. Learning about the limiting step in a practical electrochemical reaction is very important to effectively improve the electrochemical performances of the electrode materials. Li₄Ti₅O₁₂, as a zero-strain material, has been considered as a promising anode material for long life Li-ion batteries. In this study, our results show that the Li₄Ti₅O₁₂ pasted on Cu or graphite felt current collector exhibits unexpectedly higher rate performance than on Al current collector. For Li₄Ti₅O₁₂, the electron transfer between current collector and active material is the critical factor that affects its rate and cycling performances.     

Preparation and electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Ti<Subscript>4</Subscript>O<Subscript>7</Subscript> composite for lithium-ion batteries

In order to improve the rate capability of Li₄Ti₅O₁₂, Ti₄O₇ powder was successfully fabricated by improved hydrogen reduction method, then a dual-phase composite Li₄Ti₅O₁₂/Ti₄O₇ has been synthesized as anode material for lithium-ion batteries. It is found that the Li₄Ti₅O₁₂/Ti₄O₇ composite shows higher reversible capacity and better rate capability compared to Li₄Ti₅O₁₂. According to the charge-discharge tests, the Li₄Ti₅O₁₂/Ti₄O₇ composite exhibits excellent rate capability of 172.3 mAh g^?1 at 0.2 C, which is close to the theoretical value of the spinel Li₄Ti₅O₁₂. More impressively, the reversible capacity of Li₄Ti₅O₁₂/Ti₄O₇ composite is 103.1 mAh g^?1 at the current density of 20 C after 100th cycles, and it maintains 84.8% of the initial discharge capacity, whereas that of the bare spinel Li₄Ti₅O₁₂ is only 22.3 mAh g^?1 with a capacity retention of 31.1%. The results indicate that Li₄Ti₅O₁₂/Ti₄O₇ composite could be a promising anode material with relative high capacity and good rate capability for lithium-ion batteries.     

Research progress on the low-temperature electrochemical performance of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material

Li₄Ti₅O₁₂ is regarded as the ideal anode material for its stable structure, high charge/discharge platform, and safety performance. But low ionic and electronic conductivity of the Li₄Ti₅O₁₂ anode material under the condition of low temperature greatly limit its application in practical production. In this paper, some modified methods for improving the low-temperature electrochemical performance of Li₄Ti₅O₁₂ anode material were summarized. Meanwhile, we explored its influence mechanisms at low temperature, one is, with the subtle changes of lattice parameters and oxygen atom fraction coordinates of Li₄Ti₅O₁₂ at low temperature, the changes of the bond length influence the structural stability of Li₄Ti₅O₁₂ and the diffusion path of lithium ions; the other reason is that the charge transfer resistance increases obviously and the lithium ion diffusion coefficient reduces under low temperature. Finally, the research directions for improving the low-temperature electrochemical performance were proposed.     

Synthesis and electrochemical properties of Li4Ti5O12/C composite by the PVB rheological phase method

Spinel Li₄Ti₅O₁₂/C powders were synthesized successfully by a simple rheological phase method using polyvinylbutyral (PVB) as both template and carbon source. The structure and morphology characteristics of the composite were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy and transmission electron microscopy. The XRD results showed that the composite had a good crystallinity. Its average particle size was about 2.1 μm with a narrow size distribution as a result of homogeneous mixing of the precursors. The in situ carbon coating produced by decomposition of PVB played an important role in improving electrical conductivity, thereby enhancing the rate capacity of Li₄Ti₅O₁₂ as anode material in Li-ion batteries. The Li₄Ti₅O₁₂/C composite, synthesized at 800 °C for 15 h under argon, containing 0.98 wt% of carbon, exhibited better electrochemical properties in comparison with the pristine Li₄Ti₅O₁₂, which could be attributed to the enhanced electrical conductive network of the carbon coating on the particle surface.     

A new composite material Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>–SnO<Subscript>2</Subscript> for lithium-ion batteries

A new Li₄Ti₅O₁₂–SnO₂ composite anode material for lithium-ion batteries has been prepared by loading SnO₂ on Li₄Ti₅O₁₂ to obtain composite material with improved electrochemical performance relative to Li₄Ti₅O₁₂ and SnO₂. The composite material was characterized by X-ray diffraction and scanning electron microscopy. The results indicated that SnO₂ particles have encapsulated on the surface of the Li₄Ti₅O₁₂ uniformly and tightly. Electrochemical results indicated that the Li₄Ti₅O₁₂–SnO₂ composite material increases the reversible capacity of Li₄Ti₅O₁₂ and has good cycling reliability. At a current rate of 0.5 mA/cm², the material delivered a discharge capacity of 236 mAh/g after 16 cycles. It suggests the existence of synergistic interaction between Li₄Ti₅O₁₂ and SnO₂ and that the capacity of the composite is not a simple weighted sum of the capacities of the individual components. In the composite material, SnO₂ can act as a bridge between the spinel particles to reduce the interparticle resistance and as a good material for the Li intercalation/deintercalation. Thus, electrochemical performance of the Li₄Ti₅O₁₂ spinel can be improved by the surface modification with SnO₂, and the stability of Li₄Ti₅O₁₂ also serves to buffer the internal stress caused by the volume changes in lithium insertion and extraction reactions.     

Integrated investigation of the Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> phase stability

The Li₄Ti₅O₁₂ is applied in lithium ion batteries as anode material, which can be synthesized by various synthesis techniques. In this study, the molten salt synthesis technique at low temperatures, i.e. 350 °C, was applied to synthesize Li₄Ti₅O₁₂. Surprisingly, the Li₄Ti₅O₁₂ was not formed according to XRD analysis, which raised question about the stability range of Li₄Ti₅O₁₂. To investigate the stability of Li₄Ti₅O₁₂ at low temperatures, the high-temperature calcined Li₄Ti₅O₁₂ powder was equilibrated in the LiCl-KCl eutectic salt at 350 °C. The result of experiment revealed that the Li₄Ti₅O₁₂ is not decomposed. Results of ab initio calculations also indicated that the Li₄Ti₅O₁₂ phase is a stable phase at 0 K. The products of molten salt synthesis technique were then annealed at 900 °C, which resulted in the Li₄Ti₅O₁₂ formation. It was concluded that the Li₄Ti₅O₁₂ is a stable phase at low temperatures and the reasons for not forming the Li₄Ti₅O₁₂ by molten salt technique at low temperature are possibly related to activation energy and kinetic barriers. The Li₄Ti₅O₁₂ formation energy is also very small, due to the results of ab initio calculations.     

Design and comparison of ex situ and in situ devices for Raman characterization of lithium titanate anode material

In this paper, ex situ and in situ devices for Raman observations are designed and compared with each other by using lithium titanate as working electrode. In situ cell is made for Raman spectroscopy based on a confocal microscope Raman spectrometer. The instant evolutions of lithium titanate anode material during cycle can be recorded by in situ Raman in detail. Although the in situ technique is an important method to monitor the structure evolution of lithium titanate, it is difficult to conduct an in situ experiment in most laboratories. Moreover, the existence of electrolyte and surface deposits weakens the Raman signals of sample. Therefore, the structure evolution of Li₄Ti₅O₁₂ cannot be described accurately. For comparison, air-free ex situ device is a simple and cheap tool to achieve the information from lithiated and delithiated samples. By removing the electrolyte and deposits on the sample with dimethyl carbonate, the ex situ Raman pattern shows higher signal to noise ratio than that of in situ Raman result. As a result, the shift and recovery of ex situ Raman bands confirms that the electrochemical reaction of Li₄Ti₅O₁₂ with Li in 0.0–2.0 V is not a fully reversible process but a partially reversible process.     

Electrical and electrochemical properties of molten salt-synthesized Li4Ti5−xSnxO12 (x=0.0, 0.05 and 0.1) as anodes for Li-ion batteries

Submicron-sized polyhedral Li₄Ti_5−xSn_xO₁₂ (x=0.0, 0.05, and 0.1) materials were successfully prepared by a single-step molten salt method. The structural, morphological, transport and electrochemical properties of the Li₄Ti_5−xSn_xO₁₂ were studied. X-ray diffraction patterns showed the formation of a cubic structure with a lattice constant of 8.31 Å, and the addition of dopants follows Vegard's law. Furthermore, FT-IR spectra revealed symmetric stretching vibrations of octahedral groups of MO₆ lattice in Li₄Ti₅O₁₂. The formation of polyhedral submicron Li₄Ti_5−xSn_xO₁₂ particles was inferred from FE-SEM images, and a particle size reduction was observed for Sn-doped Li₄Ti₅O₁₂. The chemical composition of Ti, O and Sn was verified by EDAX. The DC electrical conductivity was found to increase with increasing temperature, and a maximum conductivity of 8.96×10⁻⁶ S cm⁻¹ was observed at 200 °C for Li₄Ti₅O₁₂. The galvanostatic charge–discharge behavior indicates that the Sn-doped Li₄Ti₅O₁₂ could be used as an anode for Li-ion batteries due to its enhanced electrochemical properties.     

Kinetic performance of Li4Ti5O12 anode material synthesized by the solid-state method

Li₄Ti₅O₁₂ anode was successfully synthesized by solid-state method. X-ray diffraction and scanning electron micrographs show that Li₄Ti₅O₁₂ prepared by solid-state method has a purity phase with a uniform particle size in the range of 0.5?C1???m. Cyclic voltammogram reveals that there is a big irreversible capacity for the first cycle. Li₄Ti₅O₁₂ shows a stable cycling stability at 1?C rate. After 152 cycles, the discharge capacity is 213?mAh?g^?1, which keeps 93% of it at the second cycle. Electrochemical impedance spectroscopy shows that the resistance of charge-transfer of Li₄Ti₅O₁₂ electrode decreased with increasing the storage temperatures, and the lithium diffusion coefficient is increased with increasing the storage temperatures, revealing that the kinetics of Li⁺ and electron transfer into the electrodes were much faster at high temperature than that at low temperature. The apparent activation energy of the charge transfer and lithium diffusion can be calculated to be 33.1 and 27.3?kJ?mol^?1, respectively.     

Electrospinning preparation of one-dimensional Co<Superscript>2+</Superscript>-doped Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers for high-performance lithium ion battery

One-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofibers with a diameter of approximately 500 nm have been synthesized via a one-step controllable electrospinning method. The Co²⁺-doped Li₄Ti₅O₁₂ nanofibers were systematically characterized by XRD, ICP, TEM, SEM, BET, EDS mapping, and XPS. Based on the cubic spinel structure and one-dimensional effect of Li₄Ti₅O₁₂, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers exhibit the enlarged lattice volume, reduced particle size and enhanced electrical conductivity. More importantly, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers as a lithium ion battery anode electrode performs superior electrochemical performance than undoped Li₄Ti₅O₁₂ electrode in terms of electrochemical measurements. Particularly, the reversible capacity of Co²⁺-doped Li₄Ti₅O₁₂ electrode reaches up to 140.1 mAh g^?1 and still maintains 136.5 mAh g^?1 after 200 cycles at a current rate of 5 C. Therefore, one-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofiber electrodes, showing high reversible capacity and remarkable recycling property, could be a potential candidate as an anode material.     

Spinel lithium titanate (Li4Ti5O12) as novel anode material for room-temperature sodium-ion battery

This is the first time that a novel anode material, spinel Li₄Ti₅O₁₂ which is well known as a “zero-strain” anode material for lithium storage, has been introduced for sodium-ion battery. The Li₄Ti₅O₁₂ shows an average Na storage voltage of about 1.0 V and a reversible capacity of about 145 mAh/g, thereby making it a promising anode for sodium-ion battery. E_x-situ X-ray diffraction (XRD) is used to investigate the structure change in the Na insertion/deinsertion process. Based on this, a possible Na storage mechanism is proposed.     

Electrostatic spray deposition of spinel Li4Ti5O12 thin films for rechargeable lithium batteries

Spinel Li₄Ti₅O₁₂ thin films are important for the fabrication of rechargeable lithium microbatteries. Porous thin films of Li₄Ti₅O₁₂ were prepared by electrostatic spray deposition (ESD) technique with lithium acetate and titanium butoxide as the precursors. The structures of these films were analyzed by scanning electron microscopy and X-ray diffraction. Coin-type cells with a liquid electrolyte were made with the Li₄Ti₅O₁₂ films against metallic lithium. Their electrochemical performance was investigated by means of galvanostatic cell cycling, cyclic voltammetry and Ac impedance spectroscopy. It was found that pure spinel phase of Li₄Ti₅O₁₂ was obtained. After annealing at the optimal temperature of 700 °C, the films can deliver a reversible specific capacity of about 150 mAh/g with excellent capacity retention after 70 cycles. Their electrochemical characteristics were quite comparable with those of the Li₄Ti₅O₁₂ laminate electrodes containing carbon black additive.     

Preparation of carbon encapsulated Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium ion battery through pre-coating method

Carbon encapsulated Li₄Ti₅O₁₂ (C/Li₄Ti₅O₁₂) anode material for lithium ion battery was prepared by using the pre-coat method of two steps, and the TiO₂ was pre coated before the reaction with Li₂CO₃. The structure and morphology of the resultant C/Li₄Ti₅O₁₂ materials were characterized by X-ray diffraction (XRD) and scanning microscopy (SEM). Electrochemical tests showed that at 0.1 C, the initial discharge capacity was 169.9 mAh g^?1, and the discharge capacity was 80 mAh g^?1 at 5 C. After 100 cycles at 2 C, the discharge specific capacity was 108.5 mAh g^?1. Compare with one step coating method, results showed the C/Li₄Ti₅O₁₂ prepared by pre-coat method can reduce the particle’s size and effectively improve the electrochemical performance.     

Influence of post-calcination treatment on the spinel lithium titanium oxide anode material for lithium ion batteries

The influence of post-calcination treatment on spinel Li₄Ti₅O₁₂ anode material is extensively studied combining with a ball-milling-assisted rheological phase reaction method. The post-calcinated Li₄Ti₅O₁₂ shows a well distribution with expanded gaps between particles, which are beneficial for lithium ion mobility. Electrochemical results exhibit that the post-calcinated Li₄Ti₅O₁₂ delivers an improved specific capacity and rate capability. A high discharge capacity of 172.9 mAh g^?1 and a reversible charge capacity of 171.1 mAh g^?1 can be achieved at 1 C rate, which are very close to its theoretical capacity (175 mAh g^?1). Even at the rate of 20 C, the post-calcinated Li₄Ti₅O₁₂ still delivers a quite high charge capacity of 124.5 mAh g^?1 after 50 cycles, which is much improved over that (43.9 mAh g^?1) of the pure Li₄Ti₅O₁₂ without post-calcination treatment. This excellent electrochemical performance should be ascribed to the post-calcination process, which can greatly improve the lithium ion diffusion coefficient and further enhance the electrochemical kinetics significantly.     

Effects of Li/Ti ratios on the electrochemical properties of Li4Ti5O12 examined by time-resolved X-ray diffraction

Li₄Ti₅O₁₂ for anodic active material of lithium ion batteries is synthesized using different Li/Ti ratios of 3.5/5.0, 4.0/5.0 and 4.5/5.0 by a solid-state reaction between Li₂CO₃ and anatase TiO₂ at 850?°C. All samples contain a small amount of transformed rutile TiO₂ in the final Li₄Ti₅O₁₂, where the amount of rutile TiO₂ decreases with the increase in Li/Ti ratio. A stoichiometric Li₄Ti₅O₁₂ with Li/Ti = 4.0/5.0 shows a slightly larger particle size and higher charge capacity than those of Li-deficient and Li-excessive particles, while the discharging rate capability is shown to mainly depend on particle size regardless of Li/Ti ratio. According to the time-resolved X-ray diffraction patterns using a synchrotron source, however, no significant difference is found in spite of the difference in Li/Ti ratio, indicating the structural stability of Li₄Ti₅O₁₂ during the Li insertion and extraction process.     

Structural and electrochemical study on Li(Li1/3Ti5/3)O4 anode material for lithium ion batteries

Chemical and electrochemical studies have shown that various titanium oxides can incorporate lithium in different ratios. Other compounds with a spinel-type structure and corresponding to the spinel oxides LiTi₂O₄ and Li₄Ti₅O₁₂ have been evaluated in rechargeable lithium cells with promising features. The spinel Li[Li_1/3Ti_5/3]O₄ [1–5] compound is a very appealing electrode material for lithium ion batteries. The lithium insertion-deinsertion process occurs with a minimal variation of the cubic unit cell and this assures high stability which may reflect into long cyclability. In addition, the diffusion coefficient of lithium is of the order of 10⁻⁸ cm²s⁻¹ [5] and this suggests fast kinetics which may reflect in high power capabilities. In this work we report a study on the kinetics and the structural properties of the Li[Li_1/3Ti_5/3]O₄ intercalation electrode carried out by: cyclic voltammetry, galvanostatic cycling and in-situ X-ray diffraction. The electrochemical characterization shows that the Li[Li_1/3Ti_5/3]O₄ electrode cycles around 1.56 V vs. Li with a capacity of the order of 130 mAhg⁻¹ which approaches the maximum value of 175 mAhg⁻¹ corresponding to the insertion of 1 equivalent per formula unit. The delivered capacity remains constant for hundred cycles confirming the stability of the host structure upon the repeated Li insertion-deinsertion process. This high structural stability has been confirmed by in situ Energy Dispersion X-ray analysis. Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

Mechanical behavior of Li-ion-conducting crystalline oxide-based solid electrolytes: a brief review

Li-ion-conducting solid electrolytes are receiving considerable attention for use in advanced batteries. These electrolytes would enable use of a Li metal anode, allowing for batteries with higher energy densities and enhanced safety compared to current Li-ion systems. One important aspect of these electrolytes that has been overlooked is their mechanical properties. Mechanical properties will play a large role in the processing, assembly, and operation of battery cells. Hence, this paper reviews the elastic, plastic, and fracture properties of crystalline oxide-based Li-ion solid electrolytes for three different crystal structures: Li_6.19Al_0.27La₃Zr₂O₁₂ (garnet) [LLZO], Li_0.33La_0.57TiO₃ (perovskite) [LLTO], and Li_1.3Al_0.3Ti_1.7(PO₄)₃ (NaSICON) [LATP]. The experimental Young’s modulus value for (1) LLTO is ~?200 GPa, (2) LLZO is ~?150 GPa, and (3) for LATP ~?115 GPa. The experimental values are in good agreement with density functional theory predictions. The fracture toughness value for all three of LLTO, LLZO, and LATP is approximately 1 MPa m^?2. This low value is expected since, they all exhibit at least some degree of covalent bonding, which limits dislocation mobility leading to brittle behavior.     

Preparation of binder-free thin film Li4Ti5O12 anode with an adjustable thickness through anodic TiO2 nanotubes

Binder-free thickness-controllable Li₄Ti₅O₁₂ for application in lithium ion batteries was fabricated by the reaction of Li₂CO₃ and anodic nanotubular TiO₂ at 800 °C. As the concentration of Li₂CO₃ increased, the thickness of Li₄Ti₅O₁₂ film increased, leading to increase in discharge capacity. The Li₄Ti₅O₁₂ film prepared at the optimized concentration of Li₂CO₃ of 3.8 × 10^?6 mol displayed the maximum capacity of 104 μA h cm^?2 at the first cycle, which corresponds to 103 mA h g^?1. We found that excess Li₂CO₃ led to creation of LiTiO₂ phases in the Li₄Ti₅O₁₂ film, which reduced the discharge capacity. For comparison, a Li₄Ti₅O₁₂ film was prepared by the reaction of Li₂CO₃ on a non-anodized Ti foil. In this case, discharge capacity was dramatically reduced due to the formation of Li₂TiO₃ phases in Li₄Ti₅O₁₂, which was confirmed by TEM and XRD analysis.