A low-temperature electrolyte for lithium-ion batteries

In this paper, the electrochemical performance of a new low-temperature electrolyte, 0.9 mol L^?1 lithium oxalyldifluoroborate (LiODFB)/LiBF₄ (5.365:1, by mass) mixed salts in the ethylene carbonate (EC)/dimethyl sulfite (DMS)/ethyl methyl carbonate (EMC) mixed solvent (1:1:3, by volume, the same below), is studied to seek the promising candidate for advanced low-temperature lithium-ion batteries (LIBs). The results show that LIBs using this new electrolyte can be operable well at temperature below ?20 °C. This is useful to expand the application range of LIBs, especially at specific low-temperature environments, such as military and aerospace applications.     

Effect of sulfolane and lithium bis(oxalato)borate-based electrolytes on the performance of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathodes at 55 °C

To seek a promising candidate electrolyte at elevated temperature for lithium manganese oxide (LiMn₂O₄)/Li cells, the electrochemical performance of 0.7 mol L^?1 LiBOB (lithium bis(oxalate)borate)-SL (sulfolane)/DEC (diethyl carbonate) (1:1, in volume) electrolyte was studied at 55 °C. The Mn dissolution in electrolyte was analyzed by inductively coupled plasma (ICP) analysis. AC impedance measurement and scanning electron microscopy (SEM) analysis were used to analyze the formation of the surface film on the LiMn₂O₄ electrode. The results demonstrate that the LiBOB-SL/DEC electrolyte can slow down the dissolution and erosion of Mn ions, and decrease the interface impedance. Moreover, the LiBOB-SL/DEC electrolyte could obviously improve the capacity retention, the operating voltage (4.05 V), and the rate performance of LiMn₂O₄/Li cells.     

Effects of lithium bis(oxalato)borate on electrochemical stability of [Emim][Al<Subscript>2</Subscript>Cl<Subscript>7</Subscript>] ionic liquid for aluminum electrolysis

Electrodeposition of aluminum from ionic liquids has been considered a promising approach to low-temperature aluminum electrolysis. In this study, we first investigated the electrochemical stability of 1-ethyl-3-methylimidazolium chloride ([Emim][Al₂Cl₇]) electrolyte, which is a typically used electrolyte for aluminum electrodeposition. It was found that part of imidazole ions decomposed on the cathode during the electrolysis process, especially when the temperature was at or over 353 K. In order to enhance the stability of the electrolyte, we further studied the effects of lithium salt and lithium bis(oxalato)borate (LiBOB), on the electrochemical stability of the [Emim][Al₂Cl₇] ionic liquid system. It was found that the electrochemical window of the electrolyte was broadened from 2.59 to 2.74 V at 373 K by addition of 1 mol% LiBOB. With the existence of LiBOB, the reduction current density of Al₂Cl₇ ^- increased before ?0.58 V and the electrodissolution of Al was more complete. The possible mechanism on the LiBOB increases the stability of the electrolyte systems also discussed based on our theoretical calculations.     

Studies on lithium bis(oxalato)-borate/propylene carbonate-based electrolytes for Li-ion batteries

Lithium bis(oxalato)-borate (LiBOB) is a promising salt for Li-ion batteries owing to its various characteristics such as non-fluorine, non-toxicity, low cost, and safety. It has the unique merits such as the stability at high temperature and the film-forming characteristics in propylene carbonate (PC)-based electrolyte. In this work, the utilization of PC as the basal solvent and dimethyl carbonate, γ-butyrolactone and ethylene carbonate as co-solvents for LiBOB have been investigated. The results indicate that the co-solvent has conducive effects on the conductivities, viscosities, and battery performance. The conductivity and viscosity of 0.7 mol L⁻¹ LiBOB in PC+GBL+EC+DMC (1:1:1:1, v/v) are 6.22 mS cm⁻¹ and 3.74 mPa s, respectively, and it is very stable in 0–5 V range. The capacity of Li/LiFePO₄ battery is about 160 mAh g⁻¹ at 0.5 °C. Moreover, the battery has exhibited the excellent rate performance.     

Triethylbutylammonium bis(trifluoromethanesulphonyl)imide ionic liquid as an effective electrolyte additive for Li-ion batteries

Ionic liquids are promising additives for Li-ion batteries owing to its desirable physicochemical properties. Triethylbutylammonium bis(trifluoromethanesulphonyl)imide ([N₂₂₂₄][Tf₂N]) ionic liquid was synthesized and their physical and electrochemical properties were investigated. Among several quaternary ammonium ionic liquids, [N₂₂₂₄][Tf₂N] exhibited higher conductivity (1.31 mS?cm^?1), better thermal and electrochemical stabilities, and wide electrochemical window, i.e., more than 5.9 V. Standard solution was prepared by dissolving lithium bis(trifluoromethanesulphonyl)imide (LiTf₂N) in ethylene carbonates/dimethyl carbonate (1:1, by weight). The conductivity for the electrolyte containing [N₂₂₂₄][Tf₂N] and the mixed electrolyte without additives at 25 °C are 10.24 and 8.79 mS?cm^?1, respectively. LiFePO₄ half-cell containing 0.6 mol?L^?1 LiTf₂N-based organic electrolyte with [N₂₂₂₄][Tf₂N] showed relatively high initial discharge capacity and coulombic efficiency at first cycle. It is found that the mix [N₂₂₂₄][Tf₂N] electrolyte exhibits relatively high-rate capacity. The capacity retention of half-cell containing [N₂₂₂₄][Tf₂N] is 2 % more than without additive at 0.2 C. However, the rate capacity retention of the half-cell with mix [N₂₂₂₄][Tf₂N] electrolyte is above 10 % more than without additive at 0.5 C. The results showed that [N₂₂₂₄][Tf₂N] was an effective electrolyte additive in LiFePO₄ half-cell.     

Conductivity studies of poly(ethylene oxide)(PEO)/poly(vinyl alcohol) (PVA) blend gel polymer electrolytes for dye-sensitized solar cells

Poly(ethylene oxide)(PEO)–poly(vinyl alcohol) (PVA) blend-based gel polymer electrolytes (GPEs) have been prepared by blending equal weights of PEO and PVA in ethylene carbonate (EC), dimethyl sulfoxide (DMSO), tetrabutylammonium iodide (TBAI), and iodine crystals (I₂). The conductivity, diffusion coefficient, number density, and ion mobility of the electrolytes have been calculated from the impedance data obtained from electrochemical impedance spectroscopy (EIS) measurements. The GPE with the composition of 7.02 wt%, PVA, 7.02 wt% PEO, 30.11 wt% ethylene carbonate (EC), 30.11 wt% DMSO, 24.08 wt% TBAI and 1.66 wt% I₂ exhibits the highest conductivity of 5.5 mS cm^?1 at room temperature. Dye-sensitized solar cells (DSSCs) with configuration fluorine tin oxide (FTO)/titanium dioxide/N3-dye/GPE/platinum/FTO have been fabricated and tested under the white light of intensity 100 mW cm^?2. The DSSC containing the highest conducting GPE exhibits the highest power conversion efficiency, η of 5.36 %.     

Electrical and structural studies of a LiBOB-based gel polymer electrolyte

A series of gel polymer electrolytes (GPEs) containing lithium bis(oxalato)borate (LiBOB), propylene carbonate (PC), and ethylene carbonate (EC) have been investigated. Poly(ethylene oxide) (PEO) was used as the polymer. First, a series of liquid electrolytes was prepared by varying the Li:O ratio and obtained the best composition giving the highest conductivity of 7.1?×?10^?3 S cm^?1 at room temperature. Then, the PEO-based GPEs were prepared by adding different amounts of LiBOB and PEO into a mixture of equal weights of EC and PC (40 % of each from the total weight). The gel electrolyte comprises of 12.5 % of LiBOB, 7.5 % of PEO, 40 % of EC, and 40 % of PC gave the highest ionic conductivity of 5.8?×?10^?3 S cm^?1 at room temperature. From the DC polarization measurements, ionic nature of the gel electrolyte was confirmed. Fourier transform infrared (FTIR) spectra of electrolytes showed the Li⁺ ion coordination with EC and PC molecules. These interactions were exhibited in the peaks corresponding to ring breathing of EC at 893 cm^?1 and ring bending of EC and symmetric ring deformation of PC at 712 and 716 cm^?1 respectively. The presence of free Li⁺ ions and ion aggregates is evident in the peaks due to the symmetric stretching of O–B–O at 985 cm^?1.     

Utilization of saffron (<Emphasis Type="Italic">Crocus sativus L.</Emphasis>) as sensitizer in dye-sensitized solar cells (DSSCs)

Photoelectrodes of dye-sensitized solar cells (DSSCs) have been prepared using nanosized titanium dioxide that have soaked in a solution of different saffron (Crocus sativus L.) spice content in ethanol. The optimized polyacrylonitrile (PAN)-based gel polymer electrolyte with 40.93 wt.% ethylene carbonate, 37.97 wt.% propylene carbonate, 4.37 wt.% tetrapropylammonium iodide, 9.86 wt.% PAN, 1.24 wt.% 1-butyl-3-methylimidazolium iodide, 4.35 wt.% lithium iodide and 1.28 wt.% iodine has been used as the electrolyte for DSSC. The electrolyte has conductivity of 2.91 mS cm^?1 at room temperature (298 K). DSSCs were also sensitized with saffron solution that has been added with 30 wt.% chenodeoxycholic acid (CDCA) co-adsorbent and designated as DSSC P4. The solar cell converts light-to-electricity at an efficiency of 0.31%. This is 29% enhancement in efficiency for the DSSC without addition of CDCA in the saffron-ethanol solution. The DSSC exhibits current density at short-circuit (J _sc ) of 1.26 mA cm^?2, voltage at open circuit (V _oc ) of 0.48 V and 51% fill factor. DSSC P4 also exhibits the highest incident photon-to-current density of more than 40% at 340 nm wavelength.     

Dinitrile compound containing ethylene oxide moiety with enhanced solubility of lithium salts as electrolyte solvent for high-voltage lithium-ion batteries

A dinitrile compound containing ethylene oxide moiety (4,7-dioxa-1,10-decanedinitrile, NEON) is synthesized as an electrolyte solvent for high-voltage lithium-ion batteries. The introduction of ethylene oxide moiety into the conventional aprotic aliphatic dinitrile compounds improves the solubility of lithium hexafluorophosphate (LiPF₆) used commercially in the lithium-ion battery industry. The electrochemical performances of the NEON-based electrolyte (0.8 M LiPF₆?+?0.2 M lithium oxalyldifluoroborate in NEON:EC:DEC, v:v:v?=?1:1:1) are evaluated in graphite/Li, LiCoO₂/Li, and LiCoO₂/graphite cells. Half-cell tests show that the electrolyte exhibits significantly improved compatibility with graphite by the addition of vinylene carbonate and lithium oxalyldifluoroborate and excellent cycling stability with a capacity retention of 97 % after 50 cycles at a cutoff voltage of 4.4 V in LiCoO₂/Li cell. A comparative experiment in LiCoO₂/graphite full cells shows that the electrolyte (NEON:EC:DEC, v:v:v?=?1:1:1) exhibits improved cycling stability at 4.4 V compared with the electrolyte without NEON (EC:DEC, v:v?=?1:1), demonstrating that NEON has a great potential as an electrolyte solvent for the high-voltage application in lithium-ion batteries.     

Effect of sodium salts on the cycling performance of tin anode in sodium ion batteries

To determine the effect of electrolyte salts on the cycling properties of tin anodes in sodium ion batteries, sodium/tin cells were prepared using eight electrolytes containing NaCF₃SO₃, NaBF₄, NaClO₄, and NaPF₆ in ethylene carbonate-dimethyl carbonate (EC-DMC) and EC-DMC/fluoroethylene carbonate (FEC) solvents. The first charge capacity and cycling properties strongly depended on the electrolyte salts. Additionally, an appropriately chosen electrolyte salt in combination with the FEC additive improved the cycling properties of the tin electrode. The tin electrode in the presence of the FEC-containing NaPF₆-based electrolyte exhibited the best cycling properties. The first charge capacity and charge capacity after the 45th cycle were 220 and 189 mAh g^?1 _electrode, respectively at a current density of 84.7 mA g^?1 _electrode. The rate performance is also studied using the optimized electrolyte which reveals the ability of the electrode to perform in high current application. At a high current density of 4235 mA g^?1 _electrode, the capacity delivered is 24 mAh g^?1 _electrode. At a current rate of 1694 mA g^?1 _electrode, at the end of 1400th cycle, capacity is about 45 mAh g^?1 _electrode. The results of the study clearly indicate that the electrolyte salts critically affect the electrochemical performance of the tin anode in sodium ion batteries.     

Ion dynamics in methylcellulose–LiBOB solid polymer electrolytes

A polymer electrolyte system comprising methylcellulose (MC) as the host polymer and lithium bis(oxalato) borate (LiBOB) as the lithium ion source has been prepared via the solution cast technique. The electrolyte with the highest conductivity of 2.79 μS cm^?1 has a composition of 75 wt% MC–25 wt% LiBOB. The mobile ion concentration (n) in this sample was estimated to be 5.70?×?10²⁰ cm^?3. A good correlation between ionic conductivity, dielectric constant, and free ion concentration has been observed. The ratio of mobile ion number density (n) at a particular temperature to the concentration n ₀ of free ions at T?=?∞ (n/n ₀) and the power law exponents (s) exhibit opposite trends when varied with salt concentration.     

LiClO4-doped plasticized chitosan and poly(ethylene glycol) blend as biodegradable polymer electrolyte for supercapacitors

Biodegradable polymer electrolyte comprising the blend of chitosan (CS) and poly(ethylene glycol) (PEG) plasticized with ethylene carbonate and propylene carbonate, as host polymer, and lithium perchlorate (LiClO₄), as a dopant, was prepared by solution casting technique. The ionic conductivity has been calculated using the bulk impedance obtained through impedance spectroscopy. The variation of conductivity and dielectric properties has been investigated as a function of polymer blend ratio, plasticizer content and LiClO₄ concentration at temperature range of 298–343 K. The DSC thermograms show two broad peaks for CS/PEG blend and increased with increase in the LiClO₄ content. The maximum conductivity has been found to be 1.1?×?10^?4 S cm^?1 at room temperature for 70:30 (CS/PEG) concentration. The electric modulus of the electrolyte film exhibits a long tail feature indicative of good capacitance. The activation energy of all samples was calculated using the Arrhenius plot, and it has been found to be 0.12 to 0.38 eV. A carbon–carbon supercapacitor has been fabricated using this electrolyte, and its electrochemical characteristics and performance have been studied. The supercapacitor showed a fairly good specific capacitance of 47 F?g^?1.     

Preparation,properties, and Li-ion battery application of EC + PC-modified PVdF-HFP gel polymer electrolyte films

Based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and lithium tetrafluoroborate (LiBF₄) salt along with blending plasticizers, ethylene carbonate (EC) and propylene carbonate (PC), high Li-ion-conducting gel polymer electrolyte films are developed. Their properties are characterized by various techniques. The ambient temperature ionic conductivity of the 85PVdF-HFP:15LiBF₄ + 150(EC + PC) electrolyte film has a high value of 8.1 × 10^?4 S cm^?1. Its crystallinity, melting point, and electrochemical stability window are 9.5%, 115 °C, and 4.6 V, respectively. The mechanical testing shows that the Young’s modulus, yield strength, and breaking strain of this electrolyte film are 36.8 MPa, 3.4 MPa, and 320%, respectively. Lithium-ion batteries based on the gel polymer electrolyte film exhibit remarkable charge–discharge and cycling performances. The initial discharge capacity of this battery is as high as 165.1 mAh g^?1 at 0.1 C and just shows a small capacity fading of 4.8% after 120 cycles, indicating that the 85PVdF-HFP:15LiBF₄ + 150(EC + PC) system is an excellent electrolyte candidate for lithium-ion battery applications. The charge–discharge performance of the Li-ion cell fabricated with this gel polymer electrolyte film is apparently better than that of the previously reported Li-ion cells fabricated with other PVdF-HFP-based gel polymer electrolyte films.     

Effect of different compositions of ethylene carbonate and propylene carbonate containing iodide/triiodide redox electrolyte on the photovoltaic performance of DSSC

The effect of different compositions (in weight percent) of ethylene carbonate (EC) and propylene carbonate (PC) containing iodide/triiodide redox electrolyte on the photoelectrochemical performance of N719-sensitized nanocrystalline TiO₂ solar cell was studied. The cells consisted of 0.6 M 1-hexyl-2,3-dimethylimidazolium iodide, 0.1 M LiI, 0.05 M I₂ and 0.5 M 4-tert-butylpyridine in different compositions such as 1:1, 1:2, and 2:1 wt% of EC and PC. In 1:1 wt% of EC and PC containing redox electrolyte, short circuit photocurrent density (J _sc) increased and open circuit voltage (V _oc) decreased. But in 1:2 and 2:1 wt% of EC and PC containing redox electrolytes, V _oc increased and J _sc decreased but fill factor remained relatively constant. Dye-sensitized solar cells (DSSCs) prepared using these electrolytes give a short circuit photocurrent densities of 16.86, 12.71, and 12.09 mA/cm²; an open circuit voltages of 0.73, 0.78, and 0.79 V; fill factors of 0.63, 0.64, and 0.64; and an overall conversion efficiencies of 7.76, 6.34, and 6.13 % at an incident light of 100 mWcm^?2 for 1:1, 2:1, and 1:2 wt% of EC/PC containing redox electrolytes, respectively. The incident photon-to-current conversion efficiency was higher in the case of 1:1 wt% of EC and PC containing redox electrolyte than 1:2 and 2:1 wt% of EC and PC containing redox electrolyte. It revealed that 1:1 wt% of EC and PC containing iodide/triiodide redox electrolyte is an effective electrolyte system for the fabrication of long-term stable DSSC.     

A novel and shortcut method to prepare ionic liquid gel polymer electrolyte membranes for lithium-ion battery

The ionic liquid polymer electrolyte (IL-PE) membrane is prepared by ultraviolet (UV) cross-linking technology with polyurethane acrylate (PUA), methyl methacrylate (MMA), ionic liquid (Py₁₃TFSI), lithium salt (LiTFSI), ethylene glycol dimethacrylate (EGDMA), and benzoyl peroxide (BPO). N-methyl-N-propyl pyrrolidinium bis(trifluoromethanesulfonyl)imide (Py₁₃TFSI) ionic liquid is synthesized by mixing N-methyl-N-propyl pyrrolidinium bromide (Py₁₃Br) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The addition of Py₁₃TFSI to polymer electrolyte membranes leads to network structures by the chain cross-linking. The resultant electrolyte membranes display the room temperature ionic conductivity of 1.37 × 10^?3 S cm^?1 and the lithium ions transference number of 0.22. The electrochemical stability window of IL-PE is about 4.8 V (vs. Li⁺/Li), indicating sufficient electrochemical stability. The interfacial resistances between the IL-PE and the electrodes have the less change after 10 cycles than before 10 cycles. IL-PE has better compatibility with the LiFePO₄ electrode and the Li electrode after 10 cycles. The first discharge performance of Li/IL-PE/LiFePO₄ half-cell shows a capacity of 151.9 mAh g^?1 and coulombic efficiency of 87.9%. The discharge capacity is 131.9 mAh g^?1 with 95.5% coulombic efficiency after 80 cycles. Therefore, the battery using the IL-PE exhibits a good cycle and rate performance.     

Improving the rate performance and stability of LiNi<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>O<Subscript>2</Subscript> in high voltage lithium-ion battery by using fluoroethylene carbonate as electrolyte additive

Fluoroethylene carbonate (FEC) is investigated as the electrolyte additive to improve the electrochemical performance of high voltage LiNi_0.6Co_0.2Mn_0.2O₂ cathode material. Compared to LiNi_0.6Co_0.2Mn_0.2O₂/Li cells in blank electrolyte, the capacity retention of the cells with 5 wt% FEC in electrolytes after 80 times charge-discharge cycle between 3.0 and 4.5 V significantly improve from 82.0 to 89.7%. Besides, the capacity of LiNi_0.6Co_0.2Mn_0.2O₂/Li only obtains 12.6 mAh g^?1 at 5 C in base electrolyte, while the 5 wt% FEC in electrolyte can reach a high capacity of 71.3 mAh g^?1 at the same rate. The oxidative stability of the electrolyte with 5 wt% FEC is evaluated by linear sweep voltammetry and potentiostatic data. The LSV results show that the oxidation potential of the electrolytes with FEC is higher than 4.5 V vs. Li/Li⁺, while the oxidation peaks begin to appear near 4.3 V in the electrolyte without FEC. In addition, the effect of FEC on surface of LiNi_0.6Co_0.2Mn_0.2O₂ is elucidated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The analysis result indicates that FEC facilitates the formation of a more stable surface film on the LiNi_0.6Co_0.2Mn_0.2O₂ cathode. The electrochemical impedance spectroscopy (EIS) result evidences that the stable surface film could improve cathode electrolyte interfacial resistance. These results demonstrate that the FEC can apply as an additive for 4.5 V high voltage electrolyte system in LiNi_0.6Co_0.2Mn_0.2O₂/Li cells.     

A polymer electrolyte based on poly(vinylidene fluoride-hexafluoropylene)/hydroxypropyl methyl cellulose blending for lithium-ion battery

A polymer electrolyte based on the blending of poly(vinylidene fluoride-hexafluoropylene) (PVDF-HFP) and hydroxypropyl methyl cellulose (HPMC) was prepared for the first time. The structure and performance of the gel polymer electrolyte were characterized and measured by X-ray diffraction, Fourier transform infrared, thermogravimetric analysis, scanning electron microscopy, electrochemical impedance spectroscopy, linear sweep voltammetry, and by a charge/discharge test. The results show that the gel polymer electrolyte has the best performance when PVDF-HFP/HPMC ratio (w/w) is 4:1. At room temperature, the ionic conductivity can reach 0.38?×?10^?3 S cm^?1, the electrochemical stable window is up to 5.0 V (vs. Li/Li⁺), and the half cell of Li/GPE/LiMn₂O₄ shows high-discharge-specific capacity and good cycling performance.     

A piperidinium-based ester-functionalized ionic liquid as electrolytes in Li/LiFePO<Subscript>4</Subscript> batteries

A new functionalized ionic liquid (IL) based on cyclic quaternary ammonium cations with ester group and bis(trifluoromethanesulfonyl)imide ([TFSI]^?) anion, namely, N-methyl-N-methoxycarbonylpiperidinium bis(trifluoromethanesulfonyl)imide ([MMOCPip][TFSI]), was synthesized and characterized. Physical and electrochemical properties, including Li-ion transference number, ionic conductivity, and electrochemical stability, were investigated. The electrochemical window of [MMOCPip][TFSI] was 6 V, which was wide enough to be used as a common electrolyte material. The Li-ion transference number of this IL electrolyte containing 0.1 M LiTFSI was 0.56. The half-cell tests indicated that the [MMOCPip][TFSI] obviously improved the cyclability of a Li/LiFePO₄ cell. For the Li/LiFePO₄ half-cells, after 20 cycles at room temperature at 0.1 C, the discharge capacity was 109.7 mAh g^?1 with 98.7% capacity retention in the [MMOCPip][TFSI]/0.1 M LiTFSI electrolyte. The good electrochemical performance demonstrated that the [MMOCPip][TFSI] could be used as electrolyte for lithium-ion batteries.     

Effect of tetrabutylammonium iodide content on PVDF-PMMA polymer blend electrolytes for dye-sensitized solar cells

The influence of tetrabutylammonium iodide on the polyvinylidene fluoride-poly(methyl methacrylate)-ethylene carbonate (PVDF-PMMA-EC)-I₂ polymer blend electrolytes was investigated and optimized for use in a dye-sensitized solar cell. The different weight ratios (50, 60, 70, and 80 %) of tetrabutylammonium iodide (TBAI)-added PVDF-PMMA-EC-I₂ polymer electrolytes were prepared. The prepared solid polymer blend electrolytes were characterized by using various techniques such as Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC), and electrochemical impedance spectroscopy (EIS). The FT-IR spectra revealed the interaction among all composition of polymer electrolytes. The influence of TBAI salt on the ionic conductivity of polymer electrolytes was studied using electrochemical impedance spectroscopy. The polymer electrolyte containing 60 % of TBAI in PVDF-PMMA-EC-I₂ showed the highest room temperature conductivity of 5.10?×?10^?3 S cm^?1. The fabricated DSSC using PVDF-PMMA-EC-I₂ polymer electrolytes with 60 % of TBAI showed the best performance with a short-circuit current density of 8.0 mA cm^?2, open-circuit voltage of 0.66 V, fill factor of 0.65, and the overall power conversion efficiency of 3.45 % under an illumination of 100 mW cm^?2. Hence, the weight content of organic iodide salt in polymer electrolytes influences the overall performance of dye-sensitized solar cells.     

Vinyl ethylene carbonate as an electrolyte additive for high-voltage LiNi<Subscript>0.4</Subscript>Mn<Subscript>0.4</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript>/graphite Li-ion batteries

Vinyl ethylene carbonate (VEC) is investigated as an electrolyte additive to improve the electrochemical performance of LiNi_0.4Mn_0.4Co_0.2O₂/graphite lithium-ion battery at higher voltage operation (3.0–4.5 V) than the conventional voltage (3.0–4.25 V). In the voltage range of 3.0–4.5 V, it is shown that the performances of the cells with VEC-containing electrolyte are greatly improved than the cells without additive. With 2.0 wt.% VEC addition in the electrolyte, the capacity retention of the cell is increased from 62.5 to 74.5 % after 300 cycles. The effects of VEC on the cell performance are investigated by cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), x-ray powder diffraction (XRD), energy dispersive x-ray spectrometry (EDS), scanning electron microscopy (SEM), and attenuated total reflectance-Fourier transform infrared (ATR-FTIR). The results show that the films electrochemically formed on both anode and cathode, derived from the in situ decomposition of VEC at the initial charge–discharge cycles, are the main reasons for the improved cell performance.