巯基-烯光点击反应辅助合成多官能度蓖麻油基聚氨酯丙烯酸酯

研究巯基-烯光点击反应辅助合成多官能度蓖麻油基聚氨酯丙烯酸酯。首先通过光引发的巯基-烯点击反应,于蓖麻油分子上引入巯基乙醇,形成多羟基化合物,然后加入丙烯酸羟丙酯与异佛尔酮二异氰酸酯,以物质的量为1:1反应得到端异氰酸酯丙烯酸酯,最终得到蓖麻油基聚氨酯丙烯酸酯。通过调节羟基含量可以得到不同官能度的丙烯酸酯。采用红外光谱、核磁氢谱、热重分析等手段表征其结构和性能,并测试了合成的聚氨酯丙烯酸脂的吸水率、附着力等性能,同时考察了它的热稳定性。结果表明, 在紫外光照射下,巯基和不饱和双键之间发生了加成反应;该聚合物的固化膜性能得到提高,尤其是硬度和热稳定性。由本文快速合成方法得到的树脂性能良好,具有较好的应用前景,扩大了巯基-烯光点击反应在高性能UV固化材料方面的应用范围。     

Structure and reactivity of bis(iodozincio)methane solution

Bis(iodozincio)methane, which has been shown to be an efficient reagent for organic synthesis, is obtained as THF solution. The structural information about the reagent as THF solution was corrected by small angle neutron scattering and by anomalous X-ray scattering. Those scattering experiments implied that the prepared bis(iodozincio)methane exists without forming any oligomer or aggregate. A coordination of tetrahydrothiophene to bis(iodozincio)methane enhances the nucleophilicity of the reagent and stabilizes its monomeric structure in the solution.     

Flame retardant epoxy polymers based on all phosphorus-containing components

A phosphorus-containing epoxy resin, bis(3-t-butyl-4-glycidyloxyphenyl-2,4-di-t-butylphenyl)resorcinol diphosphate, was synthesized and subsequently cured with non-phosphorus containing amines, and/or novel phosphorus-containing aromatic or polyoxyalkylene amines. Chemical structures of these materials were characterized with FTIR, NMR, elemental analysis, and amine titration. The introduction of soft -P-O- linkage, polyoxyalkyene, or hard aromatic group into the backbones of the synthesized phosphorus-containing amines provides epoxy polymers with high phosphorus contents and tailored flexibility. Thermal analysis of differential scanning calorimeter and thermal gravimetric analysis (TGA) reveals that these resulted epoxy polymers possess moderate T_gs and thermal stability. Furthermore, high char yields in TGA analysis and high limited oxygen index values indicate that these phosphorus-containing epoxy polymers possess excellent flame retardant properties.     

Analysis of six aromatic amines stability in workplace measurement

For aromatic amine determination in workplaces, stabilities of six types of carcinogenic aromatic amines (2,4-diaminotoluene, 4,4'-diamino-3,3'-dimethyldiphenylmethane, o-tolidine, 3,3'-dichlorobenzidine, 4,4'-methylenebis(2-chloroaniline), and o-dianisidine) were evaluated with air or argon gas bubbling for 45 min in aqueous solution under light irradiation (desk lamp) and heating conditions. Gas chromatography–mass spectrometry (GC–MS) was used to identify and quantify the aromatic amines. The following conditions were selected: temperature program 70°C (1 min), 7 grad/min up to 120°C (1 min), 10 grad/min up to 300°C (5 min), carrier gas flow rate 1.0 mL/min. 3,3'-Dichlorobenzidine concentration decreased by approximately 10% after irradiation with a desk lamp for 45 min in distilled water, and a monochloro compound was detected by GC–MS. The other aromatic amines were rarely different from the 0-min concentration. The shielding prevented the decomposition of 3,3'-dichlorobenzidine in distilled water.     

Ceramers Based on Crosslinked Epoxy Resins-Silica Hybrids: Low Surface Energy Systems

Ceramers based on silica and bisphenol-A epoxy resin cured with methyl nadic anhydride (MNA) and diamino diphenyl sulphone (DDS) were prepared in THF solutions. Compatibilization was induced through functionalization of the epoxy resin with amine trialkoxy silanes prior to mixing with a pre-hydrolyzed tetralkoxysilane solution (TEOS).The epoxy ceramers were further modified by the addition of small amounts of a silane functionalized alkane perfluoroether oligomer.A morphology consisting of very fine interpenetrating phases could be easily achieved through the silane functionalization of the epoxy resin. The final ceramer, however, always displayed a reduction in the glass transition temperature (Tg), resulting either from reactions of the anhydride hardener with the ethanol produced from the hydrolysis of TEOS or from the reaction of the acid catalyst with the epoxy groups.The use of the perfluoroether oligomer produced a large reduction in surface energy due to migration of the fluorinated components to the outer layers of the films.     

Microwave-enhanced bismuth triflate-catalyzed epoxide opening with aliphatic amines

In the presence of a catalytic amount of Bi(OTf)₃·4H₂O and under microwave irradiation, neat mixtures of epoxides and amines afforded smoothly the corresponding 2-amino alcohols. A wide variety of aliphatic amines were reacted with cycloalkene oxide, styrene oxide, and stilbene oxide. The reaction proceeded rapidly and afforded the 2-amino alcohols in high up to quantitative yields. All products could be obtained without aqueous work-up by simple filtration.     

Absorption,fluorescence, and photoinitiating properties of the aromatic ethers and aromatic amines complexes of cyclopentadienyliron

The aromatic ethers complexes of cyclopentadienyliron (O-CpFe) and aromatic amines complexes of cyclopentadienyliron (N-CpFe) were prepared by coupling several aniline derivatives and phenol derivatives with (η6-chlorobenzene) (η5-cyclopentadienyl) iron hexafluorophosphate through nucleophilic aromatic substitution reaction. The UV/vis absorption, fluorescence, and excitation spectra of the compounds were measured. The abilities of the photoinitiator in photopolymerizing the diglycidyl ether of the bisphenol-A epoxy oligomer under a halogen lamp were evaluated by near-infrared spectroscopy. The results show that the absorption of N-CpFe is higher than that of O-CpFe in the visible region. However, the photoinitiation ability of N-CpFe is lower than that of O-CpFe.     

Synthesis of Aromatic Polythioethers Containing 1,3,5-Triazine Ring by Aromatic Nucleophilic Substitution Polymerization

Abstract

Reaction of 2,4-dichloro-6-phenyl-1,3,5-triazines with bis(4-mercaptophenyl) sulfide in the presence of a base in THF afforded the corresponding condensation polymer as a whole aromatic polythioether in moderate yield. The polymerization of several 2,4-dichloro-1,3,5-triazine derivatives with this dithiols also proceeded in the o-dichlorobenzene-water two-phase system by using phase transfer catalysts. The resulting polymers consisted of THF-soluble and -insoluble fractions. The x-ray diffraction pattern indicated that these THF-insoluble polymers have a highly crystalline nature. Further, the polymers obtained here showed high thermal stability.     

Curing of epoxy oligomers by the eutectic mixture of aromatic amines

Kinetics of curing of structurally different epoxy oligomers (ED-20 and PDI-3AK resins) in a mixture with other low-molecular-weight epoxy oligomers and plasticizers by the eutectic mixture of aromatic amines UP-0638/1 is studied by the DSC method. The activation energy and the heats of curing reactions are determined. It is established that crosslinked epoxy polymers cured at moderate temperatures (40–80°C) are strong moisture-resistant compositions with different mechanical characteristics. Plasicized elastomers based on PDI-3AK resin with glass transition temperatures of ?78 and ?95°C are freeze-and heat-resistant materials.     

Formation of the Interphase of a Cured Epoxy Resin Near a Metal Surface: Reactive Coarse-Grained Molecular Dynamics Simulations

Mesoscale molecular dynamics simulations are performed to analyze the curing process of an epoxy resin with polyfunctional amines on a generic surface. The coarse grained potentials were derived from all-atomistic molecular dynamics simulations using iterative Boltzmann inversion. The reactive scheme incorporates cross-linking between an epoxy resin and an amine, as well as amine adsorption on the surface. The structure of the cured network is examined and compared with equilibrium properties of the uncured system. Special attention has been paid on the implications of the surface that is believed to play a crucial role in the performance of epoxy systems.     

Structure and properties of epoxy composites cured with new organosilicon amines

The results of the curing of bisphenol A-based epoxy oligomers (ED-20 and NPEL-128) with silicon-containing amines (SCAs) synthesized by the interaction between bifunctional alcohols with different molecular masses and γ-aminopropyltriethoxysilane (AGM-9) are reported. It is shown that, in the case of using SCAs, epoxy oligomer is cured more completely and a higher degree of elasticity in the polymer matrix is achieved without using modifiers, which is impossible in the case when polyethylene polyamines are used.     

A novel cyclic dithiocarbonate having siloxane moiety; Approach to curable siloxane oligomer

A novel 5‐membered cyclic dithiocarbonate (DTC) having a siloxane moiety, 5‐(3‐trimethoxysilylpropyloxymethyl)‐1,3‐oxathiolane‐2‐thione, was synthesized from the corresponding epoxide precursor by its cycloaddition with carbon disulfide. The siloxane group underwent condensation reaction by the treatment with water and a basic or acidic catalyst, to afford the corresponding oligomer having siloxane main chain and DTC pendant. The resulting oligomer was liquid and soluble in organic solvents such as THF and chloroform. Treatment of the oligomer with amines resulted in selective ring‐opening reaction of the DTC group, generating a thiol group, which underwent oxidative coupling reaction to make the oligomer successfully cured. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4422–4430, 2005     

Polyurethane adhesive composition cured at room temperature

The influence of polyfunctional hydroxyl-containing oligomer on the rheological, physicomechanical, and adhesive properties of polyurethane composite based on multicomponent oligomer blend and polyisocyanate is investigated. The kinetics of curing is investigated by the viscometric method, and the composition lifetime is determined. It is shown that the polyurethanes under investigation can be used as fast-curing adhesive composites of cold curing operating in a temperature interval of up to +90°C.     

Synthesis of novel nitrogen-containing polymers by Pd(0)-catalyzed polycondensation of propargylic carbonates and bifunctional nitrogen nucleophiles

A Pd(0)-catalyzed polycondensation of propargylic carbonates and bifunctional nitrogen nucleophiles was investigated. The polycondensation was carried out in THF at 80 °C for 20 h in the presence of a Pd(0) catalyst. The Pd(0)-catalyzed polycondensation with bifunctional nitrogen nucleophiles proceeded successfully when bis[(2-diphenylphosphino)phenyl]ether (DPEphos) was used as the ligand. N-monoalkylated bifunctional benzenesulfonamides and pyromellitic diimide could be used in the polycondensation. Aliphatic and aromatic amines did not afford the corresponding polymers at all. The molecular weights of the obtained polymers were higher when propargylic carbonates having an aryl group on the acetylenic terminal carbon were used.     

Thermal latency of novel chelating borate catalysts as latent catalysts for epoxy–phenolic resins

Novel quaternary ammonium bis(2‐oxybenzoyloxy)borate salts ( 1a – 1c ) or quaternary ammonium bis(1,2‐benzenedioxy)borate salts ( 2a and 2b ) with tetra‐n‐butylammonium (TBA⁺), tetra‐n‐octylammonium (TOA⁺), or bis(triphenylphosphoranylidene)ammonium (PNP⁺) cations were synthesized as latent catalysts of epoxy/phenol–novolac resins by the complexation between boric acid and salicylic acid or catechol, followed by neutralization with quaternary ammonium hydroxide. Polyaddition reactions of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐bisphenol F (44BPF) or bisphenol F (BPF‐D) with the ammonium borates were investigated as model reactions of epoxy/phenol–novolac resin systems with respect to the thermal latency and storage stability of the catalyst. The polyaddition of DGEBA/44BPF with 1a – 1c in diglyme at 150 °C for 6 h proceeded up to 85–96% conversions and gave polymers with number‐average molecular weights of 4180–10,500, whereas the polyaddition at 80 °C for 6 h gave less than 8% conversions. However, the polyaddition with 2a containing TBA⁺ cation proceeded to only a 32% conversion at 150 °C for 6 h in diglyme and to a 64% conversion even at 180 °C for 6 h in triglyme and only gave low molecular weight oligomers, and no reaction proceeded in the polyaddition at 80 °C. However, polyaddition with 2b containing PNP⁺ cation proceeded up to a 96% conversion at 150 °C for 6 h in diglyme and gave a higher molecular weight polymer with a number‐average molecular weight of 8050, whereas the polyaddition at 80 °C for 6 h gave only a 5% conversion. The catalytic activity of ammonium borates 1a – 1c and 2a and 2b depended on the borate anion structure: 1a and 1c with bis(2‐oxybenzoyloxy)borate anion revealed higher activity than 2a and 2b with bis(1,2‐benzenedioxy)borate anion, respectively. In comparison with tetra‐n‐butylammonium bromide (TBAB) as a conventional ammonium salt or tetra‐n‐butylammonium tetrakis(benzoyloxy)borate (TBA‐TBB), 1a – 1c and 2b revealed better thermal latency. The catalytic activity of ammonium borates also depended on the bulkiness of the ammonium cation, and the order of activity was 1c (PNP⁺) > 1b (TOA⁺) ≧ 1a (TBA⁺) and 2b (PNP⁺) > 2a (TBA⁺). The storage stability of DGEBA/BPF‐D with the ammonium borate catalysts 1a – 1c and 2a and 2b in bulk at 40 °C was much better than that with TBAB and TBA‐TBB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2702–2716, 2002     

Synthesis and photochemical properties of novel pentamethylated norbornadiene containing polyimides

A novel pentamethylated norbornadiene (NBD) based dianhydride, α,α′‐bis‐(3,4,5,6,7‐pentamethylcyclopenta‐2,4‐dienyl)meta‐xylene‐1,2‐dianhydride (3), was prepared from α,α′‐bis‐(pentamethylcyclopentadienyl)meta‐xylene (1) and acetylene dicarboxylic acid. The bis‐adduct formed via Diels–Alder reaction afforded tetra‐acid (2), which was chemically cyclodehydrated to lead the targeted dianhydride (3). New polyimides containing NBD moieties in the main chain were prepared from the dianhydride monomer (3) and various aromatic diamines. The chemical structure of the polymers was confirmed by both ¹H and ¹³C NMR analysis. Their Molecular weights were also measured by SEC. All of these polyimides are soluble at room temperature in common organic solvents, such as chloroform, dichloromethane, THF, DMSO, DMF, and NMP, and show good thermal stabilities. The photochemical isomerization of the NBD into quadricyclane (QC) was investigated by UV/vis spectrophotometry from polymer films using visible sunlight as irradiation source. It was found that the kinetic rate of the conversion NBD‐QC which proceeded smoothly is a first kinetic order. The stored energies released by the transformation of QC groups into NBD ones of the irradiated polymer films were also evaluated by DSC measurement and were found to be around 90 kJ mol^?1. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Organo-Mineral Composite Materials Based on Sodium Liquid Glass,Tolylene-2,4-diisocyanate,Epoxy Oligomer,and Polyisocyanate

Organo-mineral composite materials based on sodium liquid glass combined with tolylene-2,4-diisocyanate (TDI), polyisocyanate, and epoxy oligomer have been synthesized. When heated, the organic components of the composites form a polymer network through the trimerization reaction and TDI curing of the epoxy oligomer. The composite materials after heating to 130°C have a uniform structure. The resulting hybrid composite materials are not brittle and exhibit enhanced heat resistance as compared to common polyisocyanurate compositions. Hybrid composites can find wide application in various fields of engineering.     

Surface graft polymerization of glycidyl methacrylate onto polyethylene and the adhesion with epoxy resin

Surface graft polymerization of glycidyl methacrylate (GMA) was carried out onto a high- density polyethylene (PE) sheet pretreated with corona to introduce peroxides onto the PE surface. Graft polymerization of GMA was effected by UV irradiation of the coronatreated PE in the presence of monomer solution without the use of any photosensitizer. The graft layer was found by staining the PE cross section to localize in the surface region of PE. The physical change in the PE surface was characterized by scanning electron microscopy, while the chemical changes due to the GMA graft polymerization were assessed by the dynamic contact angle, FT-IR, and x-ray photoelectron spectroscopy (XPS) measurement. The peroxide formation by corona exposure was confirmed by the XPS measurement after derivatization with SO₂. The epoxy groups introduced onto the PE surface by the GMA graft polymerization were reactive with water (in the presence of HCI) and amines. The adhesion between the GMA-grafted PE and an epoxy resin was studied by means of a shear strength test method. The GMA-grafted PE exhibited strong interfacial adhesion with the epoxy resin, compared to the original and corona-treated PE. The adhesion strength of the GMA-grafted PE was nearly two times higher than that of the corona-treated PE. This strongly suggests that the enhanced adhesion between the surface-grafted PE and the epoxy resin is ascribed to covalent bonding of the epoxy groups on the GMA-grafted surface to the amines in the epoxy resin. © 1995 John Wiley & Sons, Inc.     

A novel halogen‐free co‐curing agent with linear multi‐aromatic rigid structure as flame‐retardant modifier in epoxy resin

A novel halogen‐free 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO)‐containing co‐curing agent, 6,6′‐(1,4‐phenylenebis(((4‐(phenylamino)phenyl)amino)methylene))bis(dibenzo[c,e][1,2]oxaphosphinine 6‐oxide) (DPN) was synthesized via a simple 1‐pot or 2‐step procedure with yield of 86.2% and 70.8%, respectively. The molecular structures of 4,4′‐((1,4‐phenylenebis(methanylylidene))bis(azanylylidene))bis(N‐phenylaniline) (DPN intermediate) and DPN are characterized by FTIR, NMR, and MS. TGA tests show that the char yield of DPN/EP composites raises to 30.9% when the molar ratio of DPN to 4,4‐diaminodiphenyl methane(DDM) is 20:80. T_g values of DPN/EP composites tested by DSC and DMA are similar to neat epoxy resin (EP), which is due to the secondary amine in DPN that participates in the cross‐linking reaction of epoxy resin. The storage modulus in the rubber stage (E′‐190 °C) of flame‐retardant epoxy resin is close to that of neat EP, while their tanδ's are lower, which indicates the similarity of samples' cross‐linking density due to the participation of DPN in the cross‐linking reaction. The results show that when the molar ratio of DPN and DDM is 5:95, the epoxy has a higher T_g value and better mechanical properties than other samples. The introduction of DPN efficiently improves the flame‐retardant properties of epoxy resin with V‐0 rating of UL‐94 vertical burning test, non‐dripping, 41% of limit oxygen index (LOI) value, low peak heat release rate (PHRR), and total heat release (THR).     

Ti(O-i-Pr)4/Me3SiCl/Mg-mediated reductive cleavage of sulfonamides and sulfonates to amines and alcohols

A low-valent titanium generated in situ from Ti(O-i-Pr)(4), Me(3)SiCl, and Mg powder in THF reacted with aryl- and alkyl-sulfonamides of aryl and alkyl amines in a reductive N-S/S-O/S-C bond cleaving pathway to provide the corresponding amines and hydrocarbons (and thiols) derived from the sulfonyl moiety. The reagent could also cleave sulfonates to the corresponding alcohols.