Miscible polybenzimidazole blends with a benzophenone-based polyimide

Miscible blends of the aromatic polybenzimidazole, poly(2,2(m-phenylene)-5,5′-benzimidazole) (PBI), and the aromatic polyimide formed from 3,3′,4,4′-benzophenone tetracarboxylic dianhydride and 3,3′-diaminobenzophenone (LaRC TPI) have been prepared. Blends with PBI were prepared in N,N-dimethylacetamide solution starting with either the polyamic acid or a 95% imidized form of LaRC TPI; the blend was then precipitated into water or cast as films. The mixture was then imidized thermally to obtain PBI/LaRC TPI blends. Evidence for miscibility was obtained in the form of single composition dependent T_g's intermediate between those of the component polymers and single tan δ dynamic mechanical relaxation peaks. The IR spectra displayed shifts in the N? H stretching band, thereby providing evidence for specific interactions related to the miscibility of these two polymers.     

Synthesis and micropatterning properties of a novel base‐soluble,positive‐working,photosensitive polyimide having an o‐nitrobenzyl ether group

A novel positive‐working, photosensitive polyimide, poly[1,4‐phenyleneoxy‐1,4‐phenylene‐2,2′‐di(2‐nitrobenzyloxy)benzophenone‐3,3′,4,4′‐tetracarboxdiimide] (OPI‐Nb), developable with an aqueous base was prepared by the o‐nitrobenzylation of a polyimide, poly(1,4‐phenyleneoxy‐1,4‐phenylene‐2,2′‐dihydroxybenzophenone‐3,3′,4,4′‐tetracarboxdiimide) (OPI), derived from 2,2′‐dihydroxy‐3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (DHBA) and 4,4′‐oxydianiline, and it micropatterning properties were investigated. The o‐nitrobenzylation of OPI to OPI‐Nb was conducted with o‐nitrobenzyl bromide in N‐methyl‐2‐pyrrolidinone containing Et₃N. The DHBA monomer was synthesized by exhaustive KMnO₄ oxidation of bis(2‐dimethoxy‐3,4‐dimethylphenyl)methane obtained by etherification of bis(2‐hydroxy‐3,4‐dimethylphenyl)methane with iodomethane, followed by deprotection of the methoxy groups and cyclodehydration of the obtained 2,2′‐dihydroxy‐3,3′4,4′‐benzophenonetetracarboxylic acid. The intermediate bis(2‐hydroxy‐3,4‐dimethylphenyl)methane was prepared by the condensation of 2,3‐dimethylphenol with paraformaldehyde. The degree of o‐nitrobenzylation was determined to be over 94 mol % from ¹H NMR absorption of benzylic CH₂ protons. The aromatic OPI was perfectly soluble in a dilute aqueous NaOH solution and tetramethylammonium hydroxide (TMAH), whereas OPI‐Nb was not even swellable in them. In the micropatterning process, OPI‐Nb showed a line‐width resolution of 0.4‐μm and a sensitivity of 5.4 J/cm² when its thin films were irradiated with 365‐nm light and developed with a 2.38% aqueous TMAH solution at room temperature for 90 s. The thickness loss of OPI‐Nb films measured after postbaking at 350 °C was in the 8–9% range. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 776–788, 2007     

Thermotropic liquid crystalline polymer. III. Synthesis and properties of poly(amide-azomethine-ester)

A series of novel dialdehydes as new monomers, 4,4′-diformyl-α,ω-diphencarbonylalkane, 4,4′-diformyl-3,3′-methoxy-α,ω-diphencarbonylalkane, and 4,4′-diformyl-3,3′-ethoxy-α,ω-diphencarbonylalkane, was prepared from aliphatic diacid chloride with p-hydroxybenzaldehyde, vanillin, and 3-ethoxy-4-hydroxybenzaldehyde, respectively. A series of poly(amide-azomethine-ester)s was prepared by condensation of 4,4′-diaminoanilide with 4,4′-diformyl-α,ω-α,ω-diphencarbonylalkane, 4,4′-diformyl-3,3′-methoxy-α,ω-diphencarbonylalkane, and 4,4′-diformyl-3,3′-ethoxy-α,ω-diphencarbonylalkane, respectively. Their thermotropic liquid crystalline properties were examined by DSC microscope observations. In most cases, the mesophase extends up to ca. 288–380°C, where thermal decomposition prevents further observation.     

Hydrazine‐based polyimides from isomeric bis(chlorophthalimide)s

3,3′‐Dichloro‐N,N′‐biphthalimide (3,3′‐DCBPI), 3,4′‐dichloro‐N,N′‐biphthalimide (3,4′‐DCBPI), and 4,4′‐dichloro‐N,N′‐biphthalimide (4,4′‐DCBPI) were synthesized from 3‐ or 4‐chlorophthalic anhydrides and hydrazine in glacial acetic acid. The yield of 3,3′‐DCBPI (90%) was much higher than that of 4,4′‐DCBPI (33%) because of the better stability of the intermediate, 3‐chloro‐N‐aminophthalimide, and 3,3′‐DCBPI. A series of hydrazine‐based polyimides were prepared from isomeric DCBPIs and 4,4′‐thiobisbenzenethiol (TBBT) in N,N‐dimethylacetamide in the presence of tributylamine. Inherent viscosity of these polymers was in the range of 0.51–0.69 dL/g in 1‐methyl‐2‐pyrrolidinone (NMP) at 30 °C. These polyimides were soluble in 1,1,2,2‐terachloroethane, NMP, and phenols. The 5% weight‐loss temperatures (T_5%s) of the polymers were near 450 °C in N₂. Their glass‐transition temperatures (T_gs) determined by dynamic mechanical thermal analysis and differential scanning calorimetry increased according to the order of polyimides based on 4,4′‐DCBPI, 3,4′‐DCBPI, and 3,3′‐DCBPI. The hydrolytic stability of these polymers was measured under acid, basic, and neutral conditions and the results indicated that the order was 3,3′‐DCBPI/TBBT > 3,4′‐DCBPI/TBBT > 4,4′‐DCBPI/TBBT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4933–4940, 2007     

New polymer syntheses. LXXXII. Syntheses of poly(ether-sulfone)s from silylated aliphatic diols including chiral monomers

Attempts were made to synthesize poly(ether-sulfone)s from aliphatic diols or bissilylated diols on the one hand, and 4,4′-dichlorodiphenylsulfone or 4,4′-difluorodiphenylsulfone on the other hand. The reaction conditions and the catalyst were varied. Polycondensations of silylated diols with 4,4′-difluorodiphenylsulfone and powdered K₂ CO₃ in N-methylpyr-rolidone proved to give the best results. Using silylated isosorbide and isomannide as mono-mers chiral poly(ether-sulfone)s were prepared. GPC measurements indicate weight-average molecular weights in the range of 27×10³–200×10³. © 1995 John Wiley & Sons, Inc.     

Synthesis and comparative study on polyetherimides from isomeric 4,4′-isopropylidenediphenoxy bis(phthalic anhydride)s

Two isomers of commercial 4,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (4,4′-BPADA), that is, 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,4′-BPADA) and 3,3′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,3′-BPADA), were synthesized through aromatic nucleophilic substitution from nitrophthalonitrile and bisphenol A. 3,4′-BPADA was first synthesized from two intermediates, that is, 3-(4-[4-hydroxyphenylisopropylidene] phenoxy) phthalonitrile (3-BPADN) and 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalonitrile) (3,4′-BPATN). The corresponding three series of polyetherimides (PEIs) were prepared with two representative aromatic diamines (4,4′-oxydianiline and m-phenylenediamine (m-PDA)) via two-step procedure and chemical imidization. Isomeric polyimides showed T_gs from 206 to 256°C in nitrogen and T_d5%s from 488 to 511°C in argon, good mechanical properties (tensile moduli of 2.3–3.3 GPa, tensile strengths of 70–96 MPa, and elongations at break of 3.2%–5.1%), and good solubility. With the introduction of 3-substituted phthalimide unit, PEIs displayed higher T_g values, lower strengths and elongations, better solubility and larger d-spacings. The rheological properties of thermoplastic polyimide resins based on the BPADA isomers were investigated, which showed that polyetherimide PEI-3b derived from 3,3′-BPADA and m-PDA had the lowest melt viscosity among the isomers, indicating that the melt processibility had been greatly improved.     

Low‐CTE photosensitive polyimide based on semialicyclic poly(amic acid) and photobase generator

A negative‐type photosensitive polyimide (PSPI) based on semialicyclic poly(amic acid) (PAA), poly(trans‐1,4‐cyclohexylenediphenylene amic acid), and {[(4,5‐dimethoxy‐2‐nitrobenzyl)oxy]carbonyl} 2,6‐dimethylpiperidine (DNCDP) as a photobase generator has been developed as a next‐generation buffer coat material. The semialicyclic PAA was synthesized from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and trans‐1,4‐cyclohexyldiamine in the presence of acetic acid, and the PAA polymerization solution was directly used for PSPI formulation. This PSPI, consisting of PAA (80 wt %) and DNCDP (20 wt %), showed high sensitivity of 70 mJ/cm² and high contrast of 10.3, when it was exposed to a 365‐nm line (i‐line), postexposure baked at 190 °C for 5 min, and developed with 2.38 wt % tetramethylammonium hydroxide aqueous solution containing 20 wt % isopropanol at 25 °C. A clear negative image of 6‐μm line and space pattern was printed on a film, which was exposed to 500 mJ/cm² of i‐line by a contact printing mode and fully converted to poly(trans‐1,4‐cyclohexylenebiphenylene imide) pattern upon heating at 250 °C for 1 h. The PSPI film had a low coefficient of thermal expansion of 16 ppm/K compared to typical PIs, such as prepared from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 4,4′‐oxydianiline. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1317–1323, 2010     

Preparation of Poly(amic acid) and Polyimide via Microwave-Assisted Polycondensation of Aromatic Dianhydrides and Diamines

Summary: A copolycondesation-type poly (amic acid) (PAA) was synthesized using pyromellitic dianhydride (PMDA) and 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) as dianhydride monomers, and 4,4′-oxydianiline (ODA) as a diamine monomer under microwave irradiation in dimethylformamide (DMF). PAA was then converted into a polyimide (PI) by an imidization. The structure and performance of the polymer were characterized by Fourier-transform infrared (FT-IR) spectroscopy, Proton nuclear magnetic resonance (¹H NMR) spectrometry, viscosity, X-ray diffraction (XRD), and thermogravimetric (TG) analyses. The results showed that under microwave irradiation, the intrinsic viscosity and the yield of PAA were increases, and the reaction time was shortened. The FT-IR spectra of the polymer revealed characteristic peaks for PI around 1778^– and 1723 cm^–1. TG curves indicated that the obtained PI began to lose weight at 535 °C, and its 10% thermal decomposition temperature under N₂ was 587 °C.     

Organosoluble polyimides and copolyimides based on 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenylethane and aromatic dianhydrides

1,1‐Bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenylethane (BAPPE) was prepared through nucleophilic substitution reaction of 1,1‐bis(4‐hydroxyphenyl)‐1‐phenylethane and p‐chloronitrobenzene in the presence of K₂CO₃ in N,N‐dimethylformamide, followed by catalytic reduction with hydrazine and Pd/C. Novel organosoluble polyimides and copolyimides were synthesized from BAPPE and six kinds of commercial dianhydrides, including pyromellitic dianhydride (PMDA, I_a ), 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA, I_b ), 3,3′,4,4′‐ biphenyltetracarboxylic dianhydride (BPDA, I_c ), 4,4′‐oxydiphthalic anhydride (ODPA, I_d ), 3,3′,4,4′‐diphenylsulfonetetracarboxylic dianhydride (DSDA, I_e ) and 4,4′‐hexafluoroisopropylidenediphthalic anhydride (6FDA, I_f ). Differing with the conventional polyimide process by thermal cyclodehydration of poly(amic acid), when polyimides were prepared by chemical cyclodehydration with N‐methyl‐2‐pyrrolidone as used solvent, resulted polymers showed good solubility. Additional, I_a,b were mixed respectively with the rest of dianhydrides (I_c–f) and BAPPE at certain molar ratios to prepare copolyimides with arbitrary solubilities. These polyimides and copolyimides were characterized by good mechanical properties together with good thermal stability. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2082–2090, 2000     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

Selectively sulfonated poly(aryl ether sulfone)‐b‐polybutadiene for proton exchange membrane

A series of selectively sulfonated poly(arylene ether sulfone)‐b‐polybutadiene copolymers (SPAES‐b‐PB) were prepared based on carboxyl terminated polybutadiene (CTPB) and sulfonated poly(arylene ether sulfone) (SPAES) that was directly prepared by polycondensation of 4,4′‐isopropylidenediphenol with different molar ratios of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS) to 4,4′‐dichlorodiphenylsulfone (DCDPS), and subsequent selective postsulfonation of flexible PB block was carried out. Epoxidized modification of membranes was conducted by an in situ‐generated peracid method. The content of sulfonic acid groups attaching to aromatic rings in SPAES was determined by ¹H NMR and was in good aggrement with the controlled ratios. The effect of sulfonated rigid blocks on the postsulfonation of PB blocks was studied by Fourier transform infrared spectroscopy. The glass transition temperature (T_g) and the temperature of the melting peak (T) of membranes in acid form were studied by differential scanning calorimetry. Fenton's reagent test revealed that the selectively sulfonated SPAES‐b‐PB membranes had good stability to oxidation. The microstructure of rod‐like rigid SPAES blocks and interpenetrating network of ions were observed by transmission electron microscopy. Complex impedance measurement showed that an epoxidized membrane with SPAES‐40 exhibited the highest proton conductivity (1.08 × 10^?1 S/cm, 90 °C), which was due to the formation of obvious ionic networks. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 665–672, 2006     

The preparation of perfectly alternating poly(amide-imide)s via amide unit containing new diamine

The synthesis of N,N′-bis(4′-amino-4-biphenylene) isophthalamide (BABPI) and its applicability as a new diamine for the preparation of a series of new, high T_g, perfectly alternating poly(amide-imide)s is described. BABPI was synthesized from the catalytic reduction of the corresponding dinitro compound which was prepared by the condensation of isophthaloyl chloride and 4-amino-4′-nitrobiphenyl. The modified selective reduction technique was used for the preparation of 4-amino-4′-nitrobiphenyl from 4,4′-dinitro-biphenyl. Poly(amide-imide)s were synthesized by polycondensation of diamine BABPI with various commercially available aromatic dianhydrides via a conventional two-step procedure. In the first step, poly(amic-acid)s were prepared in a polar aprotic solvent, such as N-methyl pyrrolidone (NMP) at room temperature. Depending on the dianhydride used, intrinsic viscosities of poly(amic-acid)s were found to range between 0.43–0.69 dL/g. Bulk thermal imidization technique was used to obtain fully imidized poly(amide-imide)s at the second step. The synthesized poly(amide-imide)s showed good thermal stability up to 320°C and the 10% weight loss temperatures were recorded in the range of 525–550°C as evidenced by thermogravimetric analysis (TGA). The glass transition temperatures were found to be between 225–235°C from differential scanning calorimeter (DSC) measurements. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1149–1155, 1997     

Synthesis and properties of aromatic poly (ether sulfone)s and poly (ether ketone)s based on methyl-substituted biphenyl-4,4′-diols

Novel methyl-substituted aromatic poly (ether sulfone)s and poly (ether ketone)s were synthesized from combinations of 3,3′,5,5′-tetramethylbipheny-4,4′-diol and 2,2′,3,3′,5,5′-hexamethylbiphenyl-4,4′-diol, and 4,4′-dichlorodiphenyl sulfone and 4,4′-difluorobenzo-phenone by nucleophilic aromatic substitution polycondensation. The polycondensations proceeded quantitatively in a N-methyl-2-pyrrolidone-toluene solvent system in the presence of anhydrous potassium carbonate to afford the polymers with inherent viscosities between 0.86 and 1.55 dL/g. The methyl-substituted poly (ether sulfone)s and poly (ether ketone)s showed good solubility in common organic solvents such as chloroform, tetrahydrofuran, pyridine, m-cresol, and N,N-dimethylacetamide. The tetramethyl- and hexamethyl-substituted aromatic polyethers had higher glass transition temperatures than the corresponding unsubstituted polymers, and did not decompose below 350°C in both air and nitrogen atmospheres. The films of the methyl-substituted poly (ether ketone)s became insoluble in chloroform by the irradiation of ultraviolet light, indicating the occurrence of photochemical crosslinking reactions. © 1994 John Wiley & Sons, Inc.     

Synthesis and properties of poly(imide-sulfonate)s

Polycondensations of N,N′-bis(hydroxyalkyl)pyromellitic diimides, N,N′-bis(hydroxyphenyl)-pyromellitic diimides, N,N′-bis(hydroxyalkyl)-3,3′,4,4′-benzophenonetetracarboxylic diimides and N,N′-bis(hydroxyphenyl)-3,3′-4,4′-benzophenonetetracarboxylic diimides with aromatic disulfonyl chlorides were carried out in pyridine to produce poly(imide-sulfonate)s. The resulting polymers had inherent viscosities in the range of 0.25–0.38 dL/g. These poly(imide-sulfonate)s were insoluble in common organic solvents and had relatively good thermal stability. The TGA data showed 10% weight losses at 253–365°C and residual weights at 500°C were 22–72% in nitrogen.     

Synthesis and characterization of thermally stable sulfonated polybenzimidazoles obtained from 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone

A novel sulfonated aromatic diacid, 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone (DSDCDPS), was successfully synthesized from 4,4′‐dimethyldiphenylsulfone by sulfonation and further oxidation. A series of sulfonated polybenzimidazoles (sPBI‐SS) with various sulfonation degrees was prepared from DSDCDPS, 4,4′‐sulfonyldibenzoic acid and 3,3′‐diaminobenzidine by solution copolycondensation in poly(phosphoric acid). The chemical structure of the resulting sPBI‐SS was confirmed by FTIR and ¹H NMR. The DSDCDPS‐based sPBI‐SS with the number‐average molecular weights of 32,000–55,000 were easy to dissolve in polar aprotic solvents such as DMF, DMSO, and DMAc, and could be cast into transparent, tough, and flexible membranes. The membranes presented good thermal stabilities (5% weight loss temperatures higher than 430 °C), and the thermal degradation activation energies of the sulfonic group of sPBI‐SS40 evaluated under N₂ by both Ozawa and Kissinger methods were 266.06 and 264.79 kJ/mol, respectively. The membranes also exhibited high storage moduli, glass transition temperatures (above 238 °C) and tensile strengths (～80 MPa), in addition to water uptakes (22.3–25.2%) and low swelling degrees (<14.0%). © 2005 Wiley Periodicals, Inc. J Polym Sci A: Polym Chem 43: 4363–4372, 2005     

Studies on heat-resistant poly(metal phthalocyanine)-imide copolymers

Several new poly(metal phthalocyanine)imide copolymers have been prepared using 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BPTDA), metal(11) 4,4′,4″,4″′-phthalocyanine tetraamines (MPTA), p-phenylenediamine, 4,4′-methylenedianiline, and 9,9-bis(4-aminophenyl)-fluorene (BAF). The attractive feature of these polymers is their high thermooxidative and thermal stability. The polymer decomposition temperatures of all the imide copolymers are greater than 500°C in air and N atomspheres. Another noteworthy property is their high char yield: 60–78% at 800°C in a N₂ atmosphere. Variation of the metal phthalocyanine concentration has a remarkable effect on the thermal stability and degree of polymerization. The most preferred molar proportion of the reagents MPTA, diamine, and BTDA is 1.25:7.5:10. These polymers may be useful in the preparation of heat-resistant films and fibers.     

Direct copolymerization of sulfonated poly(phthalazinone arylene ether)s for proton‐exchange‐membrane materials

Sulfonated poly(phthalazinone ether ketone) (SPPEK) copolymers and sulfonated poly(phthalazinone ether sulfone) (SPPES) copolymers containing pendant sodium sulfonate groups were prepared by direct copolymerization. The reaction of disodium 3,3′‐disulfonate‐4,4′‐difluorobenzophenone (SDFB‐Na), 4,4′‐difluorobenzophenone (DFB), and 4‐(4‐hydroxyphenyl)‐1(2H)‐phthalazinone (DHPZ) at 170 °C in N‐methyl‐2‐pyrrolidione containing anhydrous potassium carbonate gave SPPEKs. SPPESs were similarly obtained with 3,3′‐disulfonate‐4,4′‐difluorophenyl sulfone, 4‐fluorophenyl sulfone (DFS), and DHPZ as monomers. The sulfonic acid groups, being on deactivated positions of the polymer backbone, were expected to be hydrolytically more stable than postsulfonated polymers. Fourier transform infrared and ¹H NMR were used to characterize the structures and degrees of sulfonation of the sulfonated polymers. Membrane films of SPPEKs with SDFB‐Na/DFB molar feed ratios of up to 60/40 and SPPESs with sulfonated 4‐fluorophenyl sulfone/DFS molar feed ratios of up to 50/50 were cast from N,N‐dimethylacetamide polymer solutions. Membrane films in acid form were then obtained by the treatment of the sodium‐form membrane films in 2 N sulfuric acid at room temperature. An increase in the number of sulfonate groups in the copolymers resulted in an increased glass‐transition temperature and enhanced membrane hydrophilicity. The sodium‐form copolymers were thermally more stable than their acid forms. The proton conductivities of the acid‐form copolymers with sulfonated monomer/unsulfonated monomer molar feed ratios of 0.5 and 0.6 were higher than 10^?2 S/cm and increased with temperature; they were less temperature‐dependent than those of the postsulfonated products. SPPESH‐50 showed higher conductivity than the corresponding postsulfonated poly(phthalazinone ether sulfone). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2731–2742, 2003     

Synthesis and Crystal Structure of Two One—dimensional Chain Copper Complexes [Cu（TTA）2（4,4‘’—azpy）] and [Cu（TTA）2（3,3‘’—azpy）

Two copper complexes [Cu(TTA)₂(4,4′‐azpy)] (1) and [Cu‐(TTA)₂(3,3′‐azpy)] (2) (HTTA = 1,1,1‐trifluoro‐3‐(2‐thenoyl)‐acetone, 4,4′‐azpy = 4,4′‐azobispyridine, 3,3′‐azpy = 3,3′‐azobispyridine) were synthesized and characterized. The crystal structures were determined by X‐ray diffraction analysis. The crystal 1 belongs to triclinic with space group P1 , a = 0.8515(2) nm, b = 0.9259(2) nm, c = 0.9468(2) nm, a = 66.126(9)°, β = 79.667(9)°, γ = 90.13(1)°, Z = 1, V = 0.6692(2) nm³, D_c = 3.425 g/cm³, γ = 2.113 mm^?1, F(000) = 694, R₁ = 0.0594, wR₂ = 0.1499. The crystal 2 belongs to monoclinic with space group P2₁/c, a = 1.0661(2) nm, b = 1.4296(3) ran, c = 1.0041(3) nm, β = 114.50(3)°, V = 1.3926(5) nm³, Z = 2, D_c = 1.646 g/ cm³, μ = 1.015 mm^?1, F(000) = 694, R₁, = 0.0535, wR₂ = 0.1113. In the crystals of complexes 1 and 2, the copper atoms have distorted octahedral symmetry. The two compounds possess very similar one‐dimensional linear chains linked through the rodlike 4,4′‐azpy ligands or 3,3′‐azpy ligands.     

Comparative study on polyimides from isomeric 3,3′‐, 3,4′‐, and 4,4′‐linked bis(thioether anhydride)s

Three isomeric bis(thioether anhydride) monomers, 4,4′‐bis(2,3‐dicarboxyphenylthio) diphenyl ketone dianhydride (3,3′‐PTPKDA), 4,4′‐bis(3,4‐dicarboxyphenylthio) diphenyl ketone dianhydride (4,4′‐PTPKDA), and 4‐(2,3‐dicarboxyphenylthio)‐4′‐(3,4‐dicarboxyphenylthio) diphenyl ketone dianhydride (3,4′‐PTPKDA), were prepared through multistep reactions. Their structures were determined via Fourier transform infrared, NMR, and elemental analysis. Three series of polyimides (PIs) were prepared from the obtained isomeric dianhydrides and aromatic diamines in N‐methyl‐2‐pyrrolidone (NMP) via the conventional two‐step method. The PIs showed excellent solubility in common organic solvents such as chloroform, N,N‐dimethylacetamide, and NMP. Their glass‐transition temperatures decreased according to the order of PIs on the basis of 3,3′‐PTPKDA, 3,4′‐PTPKDA, and 4,4′‐PTPKDA. The 5% weight loss temperatures (T_5%) of all PIs in nitrogen were observed at 504–519 °C. The rheological properties of isomeric PI resins based on 3,3′‐PTPKDA/4,4′‐oxydianiline/phthalic anhydride showed lower complex viscosity and better melt stability compared with the corresponding isomers from 4,4′‐ and 3,4′‐PTPKDA. In addition, the PI films based on three isomeric dianhydrides and 2,2′‐bis(trifluoromethyl)benzidine had a low moisture absorption of 0.27–0.35%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A novel cadmium(II) coordination polymer with biphenyl‐3,3′,4,4′‐tetra­carboxylic acid and 4,4′‐bipyridine

A novel cadmium(II) coordination polymer, poly[[[bis­(4,4′‐bipyridine)cadmium(II)]‐μ₃‐4,4′‐dicarboxy­biphenyl‐3,3′‐di­carboxyl­ato] 0.35‐hydrate], {[Cd(C₁₆H₈O₈)(C₁₀H₈N₂)₂]·0.35H₂O}_n, was obtained by reaction of Cd(CH₃COO)₂·3H₂O, 4,4′‐bipyridine (4,4′‐bpy) and biphenyl‐3,3′,4,4′‐tetra­car­boxylic acid (H₄L) under hydro­thermal conditions. Each Cd^II atom lies at the centre of a distorted octa­hedron, coordinated by four O atoms from three H₂L²⁻ ligands and N atoms from two monodentate 4,4′‐bpy ligands. Each H₂L²⁻ ligand coordinates to three Cd^II atoms through two carboxyl­ate groups, one acting as a bridging bidentate ligand and the other in a chelating bidentate fashion. Two Cd atoms, two H₂L²⁻ anions and four 4,4′‐bpy ligands form a ring dimer node, which links into an extended broad zonal one‐dimensional chain along the c axis.