电感耦合等离子体质谱法(ICP-MS)测定稀土矿中钇、镧、铈、镨、钕、钐、铕、钆、铽、镝、钬、铒、铥、镱、镥和钪量

通过用四酸与微波消解法溶解样品对比,建立了用硝酸、盐酸、氢氟酸、高氯酸分解样品,采用电感耦合等离子体质谱法(ICP-MS)测定稀土矿中16种元素含量。方法采用_¹⁰³Rh作为内标消除干扰,确定了最优测定条件,16种稀土元素检出限为0.0029-0.0099ng/mL,测定范围为0.0005-0.020%。精密度试验、加标回收试验及标准物质检测,结果验证了方法的可行性及准确性。该方法简单易操作,结果可靠,能满足实验分析要求。     

ICP–AES法测定铬镍不锈钢中锰、铬、镍、硅、磷、铜、钼的含量

建立电感耦合等离子体原子发射光谱(ICP–AES)法测定铬镍不锈钢中锰、铬、镍、硅、磷、铜、钼7种元素含量的方法。试样用盐酸与硝酸混合酸溶液溶解,采用溶解国家标准样品的方法制备校准曲线溶液,确定了元素最佳分析谱线。各元素的含量在其测试范围内与原子发射强度呈良好的线性关系,线性相关系数不小于0.999,7种元素的检出限在0.000 3%~0.003 0%之间。该方法应用于铬镍不锈钢标准样品的测定,测定值与认定值相符,测定值的相对标准偏差在0.12%~1.15%之间(n=8)。应用于铬镍不锈钢样品测定时,加标回收率在90%~110%之间。该方法操作简便、迅速,可满足日常铬镍不锈钢中多元素含量的检测需要。     

X射线荧光光谱法快速测定黑铜中的铜、砷、锑、铋、铅、镍、锌和锡

建立X射线荧光光谱法快速测定黑铜中的铜,砷,锑,铋,铅,镍,锌和锡等多种元素含量的方法。采用自制的黑铜样品作为标准样品建立标准工作曲线。实验确定了样品加工时最佳的铣样速度及谱线重叠干扰的校正方法,并用理论影响系数校正基体干扰。试验结果表明,各元素的工作曲线线性关系较好,线性相关系数均大于0.996。各元素的检出限在17~47μg/g之间。测定结果的相对标准偏差为0.038%~2.73%(n=7)。两个样品的测定结果与标准分析方法的测定结果相符。该方法具有较好的准确度和精密度,分析速度快,能满足炉前快速分析的需要。     

ICP-OES法测定镍铬合金中Si，Mn，Fe，Ti，Al，Cu多种元素

建立了电感耦合等离子体发射光谱法测定镍铬合金中Si,Mn,Fe,Ti,Al,Cu元素含量的分析方法。确定了溶样方法和分析谱线,采用基体匹配消除干扰。对方法精密度和准确度进行实验,实验结果表明,各元素的相对标准偏差均小于3%,加标回收率在86.8%～106.9%,镍铬合金标准物质的各元素测定结果均与标准值一致。所建立的方法快速、准确,适用于镍铬合金中多元素同时测定。     

ICP-AES法测定松树脂中铁、铅、铜、锌、铝

研究了用ＩＣＰ－ＡＥＳ法测定松树脂中的铁、铅、铜、锌、铝的方法,确定了松树脂中杂质元素同时测定的最佳工作条件．并对实际样品用 ＩＣＰ－ ＡＥＳ与ＡＡＳ法对比试验,回收率在９１％－１０４％之间,结果令人满意。该法快速、简便、可靠,适用于出口松树脂的日常检验。     

电感耦合等离子体发射光谱法(ICP-OES)测定直接法氧化锌中铝、铜、铅、铁、镉、锰

建立了电感耦合等离子体发射光谱法测定直接法氧化锌中铝、铜、铅、铁、镉、锰元素含量的分析方法。确定了溶样方法和分析谱线,对方法精密度和准确度进行了考察,结果表明,各元素的相对标准偏差在2.5%~6.5%,加标回收率在92%~105%,测定结果与其它经典分析方法测定结果一致。所建立的方法准确、快速,适用于直接法氧化锌中多元素同时测定。     

Determination of Co, Cu, Fe, Ga, W, and Zn in rocks by neutron activation and anion-exchange separation

A neutron-activation method for the simultaneous determination of cobalt, copper, gallium, iron, tungsten and zinc in rocks is described. The method is based on anion-excbange separation in hydrochloric acid media. Chemical yield is higher than 97% for all elements, except for tungsten, where the recovery of the carrier is established by re-activation. The precision is about 1-3% for the iron determination and about 3% for cobalt, copper, gallium and zinc.     

电感耦合等离子体原子发射光谱法测定镍基钎料中Cr,Si,B,Fe

建立了电感耦合等离子体原子发射光谱法测定镍基钎料中Cr,Si,B,Fe含量的新方法。以硝酸–氢氟酸溶解样品,分别选择267.716,288.158,249.677,259.940 nm作为分析谱线,不用进行基体匹配,可直接测定镍基钎料中Cr,Si,B,Fe含量。在优化的实验条件下,测定结果的相对标准偏差为0.71%~1.43%(n=11),加标回收率为97.0%~102.0%。该方法可满足日常分析对镍基钎料中Cr,Si,B,Fe含量的检测要求。     

海水中铜锌铅镉的萃取-反萃取法同时提取-原子吸收光谱法测定

采用萃取-反萃取法同时提取出海水中Cu、Zn、Pb、Cd,Cu、Pb、Cd石墨炉法测定,Zn用火焰法测定.对样品的前处理方法和最佳仪器条件进行了研究,并通过加标实验验证了方法的可靠性.结果表明:萃取-反萃取法能完全满足海水中Cu、Zn、Pb、Cd的前处理要求,可节省一半前处理时间,有溶液稳定、环保、节省试剂等优点.     

Determination of B1 2, iodine,iodochlorhydroxyquin, liothyronine,thyroxine and zinc sulfate in drugs by neutron activation analysis

Instrumental neutron activation analysis was used in this study for the determination of the elements cobalt, iodine, and zinc in pharmaceutical dosage forms in order to develop a simple, fast and accurate method for their quantitation in these products. It appears that this procedure could be established as an official method for the determination of the elements iodine and zinc in drugs, in which these are present as active ingredients. Also it could be employed as an alternative technique of the officially used methods for the determination of B_{1 2}, iodochlorhydroxyquin, liothyronine, thyroxine and other substances with pharmaceutical interest, containing these elements in their molecules.     

微波消解-电感耦合等离子体质谱(ICP-MS)法测定山东小麦中铬、镍、铜、砷、镉、铅、锌的含量

建立了微波消解-电感耦合等离子体质谱(ICP-MS)法测定山东小麦中7种重金属元素(Cr、Ni、Cu、As、Cd、Pb、Zn)的方法,并对山东地区千余份小麦进行分析。结果表明,通过使用适宜的内标和He碰撞模式,7种重金属元素的方法检出限在0.0007~0.09 mg/kg,相对标准偏差(RSD,n=6)在10%以内,标准曲线线性关系良好,相关系数均大于0.999,方法用于国家有证标准物质(GSB-3、GSB-4、GSB24)的测定,结果与标准值相符。方法灵敏度高,重现性好,定量准确,可用于大批量小麦样品的测定。     

分光光度法同时测定钙、镁、铁的研究

本文研究了以铬天青 S 为显色剂,用分光光度-CPA 矩阵法同时测定 Ca(Ⅱ)、Mg(Ⅱ)、Fe(Ⅲ)的最佳条件,进行了测定波长的选择,用于合成样品分析,取得满意的效果。     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

电感耦合等离子发射光谱法测定镍铁中Si,Mn,P,Ni

建立ICP–AES法测定新型材料镍铁中的Si,Mn,P,Ni元素的方法。考察了镍铁基体和共存元素对测定结果的影响。通过基体匹配消除基体干扰,确定各待测元素谱线为Mn 293.930 nm,P 178.280 nm,Ni 231.604 nm,Si251.611 nm。Si,Mn,P,Ni的检出限分别为0.06,0.04,0.08,0.04 mg/L,测定结果的相对标准偏差均小于5%(n=11),加标回收率在95%~105%之间。该方法操作简便、测定结果准确可靠,可用于镍铁中Si,Mn,P,Ni的含量测定。     

等离子炬-质谱技术测定白菜、萝卜、大豆、土壤中的痕量锰、钴、镍、铜、锌、砷、钼和锶

营养学家们已经确定了锰、钻、镍、铜、锌、砷、钼和锶等10多种人体所必需的痕量元素,它们对于维持人体的健康和长寿起着重要的生理作用。本文首次应用等离子炬-质谱技术测定了白菜、萝卜、大豆和土壤中这八种痕量元素的含量,并报告了它们的测定结果和标准偏差,其中土壤样品的测定值与参考值相比较,经 T 检验,两者之间在统计学上,没有显著性差异。实验证明该方法可对多种痕量元素同时定性、定量分析。操作简便、快速,灵敏度高;方法准确可靠,重现性好。为开展食品卫生学、营养学的研究,提供了更为先进的测试技术。     

Spectrophotometric determination of cobalt, nickel, palladium, copper, ruthenium and molybdenum after extraction of their isoamyl xanthate complexes into molten naphthalene

A method has been developed for the spectrophotometric determination of microamounts of Co(II), Ni(II), Cu(II), Pd(II), Ru(III) and Mo(VI) after extraction of their isoamyl xanthate complexes into molten naphthalene. The method has been applied to the determination of these metal ions in various alloys and in environmental samples (fly ash).     

X射线荧光光谱法测定含铁原料中钾、钠、锌含量

由于钠、钾为轻元素,极易受其它元素干扰,因此在生产中普遍采用电感耦合等离子体原子发射光谱(ICP-AES)法测定,但较长的分析周期不能满足高效的生产节奏。采用熔融制样,建立X射线荧光光谱法测定含铁原料中的钾、钠、锌的含量。通过实验确定了熔解铁矿石的稀释比为1∶8,在1 150℃熔融12min,K、Na、Zn的测定范围在0.01%~0.5%。用来测定含铁原料中的有害元素,结果与ICPAES法测定结果一致,满足生产检验周期和准确度的要求。     

离子色谱法测定饮用和地下水中氟化物、溴酸盐、氯化物、亚硝酸盐、硝酸盐、硫酸盐

建立离子色谱法测定饮用和地下水中F-、BrO3-、Cl-、NO2、NO3和SO42- 6种阴离子.选用IonPac(R)AS19色谱柱(4 mm×250 mm),NaOH梯度淋洗,抑制电导检测,方法检出限为0.01～0.02 mg/L.对水样进行6次平行测定,测定结果的相对标准偏差为1.1％～2.1％,加标回收率为71...     

Spectrophotometric determination of amikacin,kanamycin, neomycin and tobramycin

A spectrophotometric method for determination of neomycin, kanamycin, tobramycin and amikacin is proposed, based on the Rimini test with disodium pentacyanonitrosylferrate(II) for primary and secondary aliphatic amines. The absorbance of the coloured addition product is measured. Beer's law is valid over a wide concentration range. The method is relatively fast and can be used in control of the manufacture of the antibiotics and their purity, instead of the much slower microbiological method. It is also applicable for determination of these antibiotics in formulations.     

Direct ICP-MS determination of trace and ultratrace elements in geological materials after decomposition in a microwave oven. Part II. Quantitation of Ba, Cs, Ga, Hf, In, Mo, Nb, Pb, Rb, Sn, Sr, Ta and Tl

A new method has been developed for the rapid determination of traces of Ba, Cs, Ga, Hf, In, Mo, Nb, Pb, Rb, Sn, Sr, Ta and Tl in silicate rocks and lake, stream and river sediments. The method involved dissolution of samples in a microwave oven by heating in a pressure decomposition Teflon vessel with a mixture of HF + HNO₃ + HCl + H₃BO₃ + EDTA followed by direct multielement determination using inductively coupled plasma-mass spectrometry (ICP/MS). The method is faster than conventional dissolution of samples by open vessel acid digestion and fusion and determination by instrumental methods. The accuracy and precision of the developed method were tested by replicate analyses of a number of international geochemical reference samples of established trace element contents. Satisfactory correlation with the “recommended” or “consensus” values was found and recoveries were in most cases 95–100%. New values for Ga, In, Nb and Tl in several international geochemical reference materials are first reported in this paper.