Synergistic extraction and spectrophotometric determination of palladium(II), iron(III), and tellurium(IV) at trace level by newly synthesized p-[4-(3,5-dimethylisoxazolyl)azophenylazo]calix(4)arene

A spectrophotometric method for the determination of palladium, iron and tellurium from nitric acid media after extraction of their p-[4-(3,5-dimethylisoxazolyl)azophenylazo]calix(4)arene [DMIAPAC] complexes has been developed and possible synergistic effects have been investigated. Chloroform, carbon tetrachloride, cyclohexane, 1,2-dichloroethane, toluene and xylene were used as the diluents. The maximum enhancement was obtained in the presence of 30% 1,2-dichloroethane. The trace amounts of metals were determined spectrophotometrically. Beer’s law obeyed in the concentration range of 5.0–95.0 μg, 8.0–120.0 μg and 10.0–140.0 μg/10 mL of the final solution of palladium, iron and tellurium, respectively. The molar absorptivities (l mol^?1cm^?1) and Sandell’s sensitivities (μg cm ^?1) were calculated: Pd(II) = 1.73 × 10⁴ and 0.0061; Fe(III) = 1.08 × 10⁴ and 0.0052; Te(IV) = 1.67 × 10⁴ and 0.0077. Ten replicate analyses containing 20 μg of Pd(II), 12.5 μg of Fe(III) and 32 μg of Te(IV) gave mean absorbance of 0.326, 0.242 and 0.418 with relative standard deviation of 0.36, 0.65 and 0.82% for Pd(II), Fe(III) and Te(IV), respectively. The interference of various ions was studied and optimum conditions were developed for the determination of these metals in certain alloys and synthetic mixtures.     

Spectrophotometric determination of palladium with glyoxime and chloroform extraction

Palladium(II) reacts with glyoxime in a 1:2 mole ratio to form a yellow water-insoluble chelate, which is soluble in chloroform; the solution has an absorption maximum at 397 mμ. Absorbance measurements at 397 mμ allow determination of the palladium glyoximate in solution. The maximum amount of palladium is extracted at pH 1.0. Platinum(II), iridium(III), gold(III), and phosphate cause some positive interference, and iron(II, III) causes negative interference; the interferences can be eliminated by masking with EDTA. The species extracted has been shown to be identical with that used to prepare the original palladium glyoximate chloroform solution. With EDTA and multiple extractions, the method is satisfactory for the determination of palladium in the presence of other platinum-group elements and many other cations.     

Sorption-spectrometric determination of palladium and gold using silica chemically modified with dipropyl disulfide groups

It has been found that silica chemically modified with dipropyl disulfide groups (DPDSS) quantitatively extracts palladium(II) from solutions in the acidity range from 4 M HCl to pH 4 and gold(III) in the range from 1 M HCl to pH 2 with a partition coefficient at the level of n × 10⁴ cm³/g. The adsorption of palladium(II) and gold(III) at room temperature is highly selective, whereas non-ferrous and other platinum metals are not adsorbed. Sorption-atomic absorption, sorption-ICP-atomic emission, and sorption-photometric methods for the determination of palladium and gold have been developed using DPDSS. The accuracy of the methods was tested by the analysis of certified reference samples.     

Complexes of d and f Metals with 2-Methyl-3-hydroxy(amino)pyrido[1,2-a]pyrimidine-4-one. Crystal Structure of 2-Methyl-3-hydroxypyrido[1,2-a]pyrimidine-4-one

Six complexes of scandium(III), lanthanum(III), praseodymium(III), and copper(II) chlorides with 2-methyl-3-hydroxypyrido[1,2-a]pyrimidine-4-one (HL¹) and 2-methyl-3-aminopyrido[1,2-a]pyrimidine-4-one (L²), as well as hydrochloride and hydronitrate L², were isolated. The crystal and molecular structures of HL¹ were determined. HL¹ in CCl₄ solution was shown (IR data) to occur as two forms, namely, neutral and zwitterionic forms. The structures for the complexes isolated were proposed.     

A potentiometric study of the oxidation of cobalt(II) with gold(III) chloride in presence of 1,10 phenanthroline or 2,2'-bipyridine : A new titration of cobalt (II) and its application to nickel-base alloys

The redox reaction between cobalt(II) and gold(III) chloride in the presence of 1.10-phenanthroline or 2,2'-bipyridine was studied, and a titration of the cobalt(II) complex with a gold(III) chloride solution was developed. A 4-fold amount of 1,10-phenanthroline or 2,2'-bipyridine was necessary for rapid quantitative reaction; the permissible pH range was 1.5–5. The oxidation of the cobalt(II) complex proceeds rapidly at 40–50°C, and a direct potentiometric titration was possible. The following maximum errors were obtained: 3.3% for 0.2–1.0 mg Co, 2.0% for 1–5 mg Co, and 0.70% for 10–40 mg Co. The following ions did not interfere: Ni(II), Zn(II), Pb(II), Cd(II), Mn(II), Fe(II), Cr(III), Al(III), Th(IV), Se(IV), Ti(IV), U(VI), Mo(VI), SO^2-₄ and PO^3-₄. Even small quantities of silver(I), copper(II), palladium(II), mercury(II)and iron(III) interfered. The method was applied to the determination of high cobalt contents in high-temperature nickel-base alloys.     

Picolinaldehyde 4-phenyl-3-thiosemicarbazone as a spectrophotometric reagent for the selective determination of small amounts of cobalt in the presence of iron

The characteristics and analytical applications of picolinaldehyde 4-phenyl-3-thiosemicarbazone are described. This compound gives coloured reactions with cobalt(II), iron(II) and (III), nickel(II), copper(II), palladium(II) and other ions, that are much more sensitive than those with picolinaldehyde thiosemicarbazone. The 1:2 yellow cobalt(II) complex has been used for the spectrophotometric determination of cobalt in the presence of iron, and applied to steel analysis.     

Substoichiometric isotope dilution analysis of iron in biological materials by the 8-quinolinol-extraction

A highly precise and accurate method for the determination of minor amounts of iron by substoichiometric isotope dilution analysis is described. The constant amount of Fe(III) is substoichiometrically extracted with 2·10⁻⁴M oxine in chloroform from the aqueous phase of pH 9.2–10.0 containing 6·10⁻³M tartrate. The interfering ions such as Mn(II), Co(II), Ni(II), Cu(II), and Zn(II), can be removed by the preliminary extraction of Fe(III) from 7.5M hydrochloric acid solutions into isopropyl ether. The present method has been applied to the determination of iron in biological standard reference materials, i.e., the NBS Spinach (SRM-1570) and the NIES Pepperbush (SRM No. 1), and the results obtained are 548±9 ppm (NBS certified value: 550±20 ppm) and 193±4 ppm, respectively.     

A spectrometric,separation and voltammetric study of the complexation reactions of bromazepam with iron(ii),copper(ii) and cobalt(ii)

Bromazepam, in the form of a cationic iron(II) chelate, can be determined spectrophotometrically at 588 nm with a limit of detection of ca. 10^-6 M. When this chelate is ion-paired with perchlorate, it can be extracted into organic solvents such as 1,2-dichloroethane and 4-methyl-2-pentanone, and determined by atomic absorption spectrometry with a limit of detection of 1.5 × 10^-5 M bromazepam at the iron resonance 248.3-nm line. Ion-pairs involving the Fe(II), Cu(II) and Co(II) chelates and perchlorate can be separated by h.p.l.c. using a C₁₈ reverse-phase column and a mobile phase of 4:1 water—methanol, with a u.v. detector at 242 nm. This approach allowed for the determination of iron(II) ions in aqueous solution with a limit of detection of 10^-8 M. The h.p.l.c. method could also be used to quantify bromazepam spiked in plasma in the concentration range 1–10 μg ml^-1, following extraction of bromazepam from plasma and subsequent formation of the iron(II) ion-pair. Copper(II) forms a labile chelate with bromazepam in pH 4.8 acetate buffer which, when subjected to differential pulse voltammetry at the hanging mercury drop electrode, gives rise to a catalytic phenomenon which can be utilised for the determination of bromazepam in the concentration range 10^-5–10^-9 M.     

Ion-chromatographic analysis of mixtures of ferrous and ferric iron

Determinations of the aqueous iron species Fe(II) and Fe(III) are essential for a fully-informed understanding of redox processes involving iron. Most previous methods for speciation of iron have been based on the calorimetric determination of Fe(II) followed by reduction of Fe(III) and analysis for total iron. The indirect determination of Fe(III) and the consumption of relatively large sample volumes have limited the accuracy and utility of such methods. A method based on ion-chromatography has been developed for simultaneous direct determination of Fe(II) and Fe(III). Sample pretreatment involves only conventional filtration and acidification. No interferences with the iron(II) determination were found; in determination of iron(III) the only interference observed was an artifact peak (of unknown origin) that occurred only when iron(II) was present, and had an area that was a function of the iron(II) concentration and could hence be corrected for. Solutions of iron(II) free from iron(III) can be prepared by treatment with a mixture of hydrogen and nitrogen in the presence of palladium black as catalyst, to reduce the iron(III). Photoreduction of iron(III) in acidified samples increases the Fe(II)/Fe(III) ratio; no means of circumventing this effect is known, other than storing the samples in the dark and analysing them as soon as possible.     

High-performance liquid chromatographic determination of uranium using solvent extraction and bis(salicylaldehyde) tetramethylethylenediimine as complexing reagent

The reagent bis(salicylaldehyde)tetramethylethylenediimine has been used for the determination of dioxouranium(VI), based on complexation in aqueous solution at pH 6, followed by extraction in chloroform and HPLC determination on a Hypersil ODS (3 μm) column. The complex was eluted with the ternary mixture methanol-acetonitrile-water (40:30:30, v/v/v), with UV detection at 260 nm. Oxovanadium(IV), iron(III), copper(II), cobalt(II), nickel(II) and palladium(II) were completely separated and did not interfere in the determination of uranium. The linear calibration range and detection limits have been obtained. The method has been applied to the determination of uranium together with copper, iron and nickel in mineral ore samples.     

Determination of microamounts of iron by hydroxamate resin colorimetry

Summary A new, sensitive chelating ion-exchanger colorimetric method has been developed for the determination of iron at the g/l level in water, based on the direct measurement of light absorption of iron hydroxamate resin complex. In 0.2 N perchloric acid solution, iron could be rapidly, selectively and quantitatively absorbed on the hydroxamate resin. The calibration curve for iron(III) of a 25 ml solution was linear in the concentration range 8.00×10^–6 to 5.00×10^–5 M. For iron(III) with larger sample volumes, the relative detection limit was increased. Most of the metals interfered negligibly, such as Ca(II), Co(II), Cu(II), Ni(II) and Zn(II), except for higher concentration of lead(II) and mercury(II) when present at up to 400 times the concentration of iron(III). The effects of EDTA, glycine, thiourea, phosphate, nitrate and chloride on the retention of iron(III) were also examined. Only thiourea significantly influenced the retention of iron(III). The presence of sodium chloride even at a concentration of 3.5×10⁴ times that of iron(III) did not interfere at all.

---

Bestimmung von Mikromengen Eisen durch Hydroxamatharz-Colorimetrie

     

Spectrophotometric Determination of Iron (III) Using 3-Hydroxy-2-Methyl-1,4-Naphthoquinone Monoxime (HMNQM)

Iron (III) forms brown coloured complex with 3-hydroxy-2-methyl-1,4-naphthoquinone monoxime. The iron (III)-HMNQM complex is found to be soluble in DMF and exhibits maximum absorption at 470 nm in the pH range 4.5–5.5. Beer's law is obeyed upto 5.58 ppm of iron (III) and sensitivity of the reaction is 0.0046 μg/cm², with molar absorptivity of 1.21×10⁴ ? mole^?1 cm^?1. The method has been used for the determination of iron (III) in alloys.     

2-Methyl-1, 4-Naphthoquinone Thiosemicarbazone as a Sensitive and Selective Chromogenic Reagent for Microdetermination of Palladium (II)

A simple, sensitive and selective procedure has been developed for the spectrophotometric determination of palladium. Palladium (II) reacts with 2-methyl-1,4-naphthoquinone thiosemicarbazone to form an orange brown complex in the pH range 8.2–9.5. The sensitivity, in terms of Sandell's definition, is 0.0025 μg Pd/cm² at 500 nm. The system adheres to Beer's law upto 2.66 ppm of palladium and optimum concentration range for the determination of the metal is 0.3–2.29 ppm with molar absorbtivity of 4.2×10⁴ ? mole^?1 cm^?1. The complex has 1:1 molar composition, as deduced by Job's method. The determination of palladium has been carried out in presence of foreign ions especially in presence of eighth group metals.     

Spectrophotometric determination of iron after separation of its 9,10-phenanthrenequinone monoximate on microcrystalline naphthalene

A sensitive and selective spectrophotometric method has been developed for the determination of iron as Fe(II) or Fe(III) using 9,10-phenanthrenequinone monoxime (PQM) as the complexing agent. Fe(II) and Fe(III) react with PQM to form coloured water insoluble complexes which can be adsorbed on microcrystalline naphthalene in the pH ranges 3.7–6.2 and 2.0–8.4, respectively. The solid mass consisting of the metal complex and naphthalene is dissolved in DMF and the metal determined spectrophotometrically by measuring the absorbances Fe(II) at 745 nm and Fe(III) at 425 nm. Beer's law is obeyed over the concentration range 0.5–20.0 g of iron(II) and 20–170.0 g of Fe(III) in 10 ml of DMF solution. The molar absorptivities are 1.333 × 10⁴ 1 · mole^–1 · cm^–1 for Fe(II) and 2.428 × 10³1· mole^–1 · cm^–1 for Fe(III). The precision of determination is better than 1%. The interference of various ions has been studied and the method has been employed for the determination of iron in various standard reference alloys, bears, wines, ferrous gluconate, human hair and environmental samples.     

Analytische Anwendung der Di-thiobenzhydrazone von 1,2-Diketonen

Zusammenfassung Die Anwendung der Di-thiobenzhydrazone von 1,2-Dicarbonylverbindungen zur Extraktion und zur spektralphotometrischen Bestimmung von Metallionen wurde untersucht. Danach bilden die 1,2-Bisthiobenzhydrazone farbige, in organische Lösungsmittel extrahierbare Chelate ( _M=3000–14000) mit Pb(II), mit Elementen der 1., 2. und 8. Nebengruppe, vereinzelt mit In(III), häufiger mit Sb(III) und mit Bi(III). Die Chelatbitdung von Diacetyl-bis-thiobenzhydrazon und von 2,3-Pentandion-bis-thiobenzhydrazon-p-methoxy mit Cu(II), Zn(II), Cd(II), Hg(II) und Pb(II) wurde als Beispiel näher untersucht.

---

Analytical application of 1,2-diketo-bis-thiobenzhydrazones

The application of 1,2-diketo-bis-thiobenzhydrazones as ligands for the extraction and spectrophotometric determination of metal ions has been studied. The 1,2 bisthiobenzhydrazones form highly coloured ( _M=3–14×10³) and with organic solvents easily extractable chelates with Pb(II), In(III), Sb(III), Bi(III) and elements of the Ist, 2nd and 8th subgroup. The application of diacetyl-bis-thiobenzhydrazone and 2,3-pentanedione-bis-(p-methoxy)-thiobenzhydrazone for the determination of Cd(II), Cu(II), Hg(II), Pb(II) and Zn(II) has been studied in detail.

     

Preconcentration of Nickel(II) in White Wine Using Quinoxaline-2,3-dithiol and a Finely Divided Anion-Exchange Resin for the Determination by Solid-Phase Spectrophotometry

A simple and sensitive method for the determination of trace amounts of nickel(II) is described. The method is based on the adsorptive enrichment of nickel(II) as the complex with quinoxaline-2,3-dithiol using a finely divided anion-exchange resin, collection of the resin on a membrane filter by filtration, and direct measurement of the absorbance of the resultant circular thin layer by reflective spectrophotometry at 605 nm. In the presence of interfering cations such as copper(II) and cobalt(II) a sample solution is first filtered, after the addition of ammonium thiocyanate and Zephiramine, to extract these cations onto a membrane filter as the ion-pair precipitate formed between the metal-thiocyanate complex anions and Zephiramine cations, then nickel(II) in the filtrate is determined. Interferences from iron(III), silver(I), bismuth(III), cadmium(II), mercury(II), indium(III), palladium(II), platinum(IV), tin(IV), and zinc(II) can also be eliminated. The proposed method was applied to the determination of nickel in white wine. The concentrations of nickel found in 5-ml aliquots of 10 different wine samples were in the range 16.1-68.0 ng ml⁻¹.     

A sensitive and highly selective extractive spectrophotometric method for the determination of palladium

Summary A Sensitive and Highly Selective Extractive Spectrophotometric Method for the Determination of Palladium Palladium forms an anionic chelate with 4-(2-pyridylazo)resorcinol (PAR, H₂R) which is extractable with xylometazolonium cation (XMH) into chloroform in the pH range 7.2–7.8 giving an intensely pinkish red coloured solution. The coloured species exhibits maximum absorbance at 520 nm with molar absorptivity 3.34×10⁴1·mole^–1·cm^–1 and obeys Beer's law in the range 0.8–5.30g/ml of palladium. The composition of the extracting species is found to be 111 for Pd(II)PARXMH. Large concentrations of EDTA and oxalate have no interference in the spectrophotometric determination of palladium by this procedure. Based on this a highly selective and sensitive method for the determination of palladium in the presence of Zn(II), Cd(II), Hg(II), Fe(III), Mn(II), Co(III), Mo(VI), Ru(IV), Sb(III), Al(III) is described. The application of this method for the determination of palladium in synthetic mixtures corresponding to the composition of jewel alloy and stibiopalladinite mineral is also demonstrated.     

A sensitive and selective method for determination of gold(III) based on electrothermal atomic absorption spectrometry in combination with dispersive liquid-liquid microextraction using dicyclohexylamine

A combined method with dispersive liquid-liquid microextraction (DLLME) and electrothermal atomic absorption spectrometry (ETAAS) has been developed for determining gold(III). Dicyclohexylamine, a new extractant for gold(III), showed excellent performance in DLLME. Acetone was indispensable to the quantitative extraction of gold(III), contributing to decrease in hydration, decrease in the difference in the dielectric constants between the supernatant phase and the sedimented phase, and dissolution of a part of chloroform as an extraction solvent to the supernatant phase as well as improvement of dipersibility. In DLLME using a mixture of 1.0 mL of acetone and 100 μL of chloroform containing 50 mmol L⁻¹ of dicyclohexylamine, gold(III) could be extracted selectively and effectively from 8 mL of a sample solution in the presence of iron(III), cobalt(II), nickel(II), copper(II), palladium(II), and platinum(IV) at pH 1. The extracted gold(III) was determinable by ETAAS; the detection limit was 0.002 μg L⁻¹ (three times the standard deviation of the blank values, n = 8) as a gold(III) concentration in 8 mL of sample solution. The proposed method was applicable to the determination of gold in platinum metal and its alloy as well as effluent without any interference by the matrices.     

Indirect flow-injection determination of ascorbic acid by flame atomic absorption spectrometry

A continuous-flow procedure is proposed for the indirect determination of ascorbic acid, based on its reducing properties because of the oxidation of its 1,2-enediol group. Iron(III) was injected into a 1,10-phenanthroline stream, which was mixed with a sample carrier and then with a sodium picrate solution stream. In these conditions the iron(III) was reduced to iron(II) by the ascorbic acid. Thus, the iron(II) formed reacts with 1,10-phenanthroline to form a charged red complex, which with picrate ion forms a stable red-orange uncharged ion-association complex that is adsorbed on-line on a non-ionic polymeric adsorbent (Amberlite XAD-4), proportionally to the ascorbic acid in the sample. The unadsorbed iron was determined by flame atomic absorption spectrometry. The proposed method allows the determination of ascorbic acid in the range 0.5–25 g ml^–1 with a relative standard deviation of 2.9% at a rate of ca. 90 samples h^–1. This method has been applied to the determination of ascorbic acid in pharmaceutical preparations, fruit juices and sweets. The results obtained in the analysis are compared with those provided by the 2,6-dichloroindophenol method.     

Determination of iron(II) and iron(III) by flow injection and amperometric detection with a glassy carbon electrode

Flow injection analysis can be used for the determination of both iron(II) and iron(III) with an amperometric detector. The flow-through cell contains a glassy carbon electrode. Selection of the appropriate voltammetric technique, choice of the indication potentials, sample size, composition of the carrier stream, etc., are discussed. The limit of determination is about 10^-6 M; the calibration curves are linear in the concentration ranges 10^-3–10^-5 M for iron(III) and 5 × 10^-4–10^-5 M for iron(II). To illustrate the potentialities of the proposed method, standard rocks have been analysed.